torque INFINITI QX56 2011 Factory Service Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2011, Model line: QX56, Model: INFINITI QX56 2011Pages: 5598, PDF Size: 94.53 MB
Page 5188 of 5598
![INFINITI QX56 2011 Factory Service Manual
TM-100
< BASIC INSPECTION >[7AT: RE7R01B]
STALL TEST
STALL TEST
Inspection and JudgmentINFOID:0000000006226793
INSPECTION
1. Inspect the amount of engine oil. Replenish the engine oil if necessary.
2](/img/42/57033/w960_57033-5187.png "INFINITI QX56 2011 Factory Service Manual
TM-100
< BASIC INSPECTION >[7AT: RE7R01B]
STALL TEST
STALL TEST
Inspection and JudgmentINFOID:0000000006226793
INSPECTION
1. Inspect the amount of engine oil. Replenish the engine oil if necessary.
2")
TM-100
< BASIC INSPECTION >[7AT: RE7R01B]
STALL TEST
STALL TEST
Inspection and JudgmentINFOID:0000000006226793
INSPECTION
1. Inspect the amount of engine oil. Replenish the engine oil if necessary.
2. Drive for about 10 minutes to warm up the vehicle
so that the A/T fluid temperature is 50 to 80°C (122 to
176 °F). Inspect the amount of AT F. Replenish if necessary.
3. Securely engage the parking brake so that the tires do not turn.
4. Start the engine, apply foot brake, and place selector lever in “D” position.
5. Gradually press down the accelerator pedal while holding down the foot brake.
6. Quickly read off the stall speed, and quickly release the accelerator pedal. CAUTION:
Never hold down the accelerator pedal for more than 5 seconds during this test.
7. Shift the selector lever to “N” position.
8. Cool down the ATF. CAUTION:
Run the engine at idle for at least 1 minute.
9. Repeat steps 5 through 8 with selector lever in “R” position.
JUDGMENT OF STALL TEST
O: Stall speed within standard value position
H: Stall speed higher than standard value
L: Stall speed lower than standard value
Stall test standard value position
Stall speed : Refer to TM-297, "Stall Speed".
Selector lever position
Possible location of malfunction
“D” and “M” “R”
Stal l s pe ed HO
Low brake
1st one-way clutch
2nd one-way clutch
OH Reverse brake
1st one-way clutch
2nd one-way clutch
L L Engine and torque converter one-way clutch
H H Line pressure low
Does not shift-up “D” or “M” position 1 → 2 Slipping in 2GR, 3GR, 4GR or 6GR 2346 brake slippage
Does not shift-up “D” or “M” position 2 → 3 Slipping in 3GR, 4GR or 5GR Direct clutch slippage
Does not shift-up “D” or “M” position 3 → 4 Slipping in 4GR, 5GR, 6GR or 7GR High and low reverse clutch slippage
Does not shift-up “D” or “M” position 4 → 5 Slipping in 5GR, 6GR or 7GR Input clutch slippage
Does not shift-up “D” or “M” position 5 → 6 Slipping in 2GR, 3GR, 4GR or 6GR 2346 brake slippage
Does not shift-up “D” or “M” position 6 → 7 Slipping in 7GR Front brake slippage
Revision: 2010 May2011 QX56
Page 5189 of 5598
![INFINITI QX56 2011 Factory Service Manual
A/T POSITIONTM-101
< BASIC INSPECTION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
A/T POSITION
InspectionINFOID:0000000006226794
1. Place selector lever in “P” position, and turn ignition s](/img/42/57033/w960_57033-5188.png "INFINITI QX56 2011 Factory Service Manual
A/T POSITIONTM-101
< BASIC INSPECTION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
A/T POSITION
InspectionINFOID:0000000006226794
1. Place selector lever in “P” position, and turn ignition s")
A/T POSITIONTM-101
< BASIC INSPECTION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
A/T POSITION
InspectionINFOID:0000000006226794
1. Place selector lever in “P” position, and turn ignition switch ON (engine stop).
2. Check that selector lever can be shifted to other than “P” position when brake pedal is depressed. Also
check that selector lever can be shifted from “P” position only when brake pedal is depressed.
3. Shift the selector lever and check for excessive effort, sticking, noise or rattle.
4. Confirm that the selector lever stops at each pos ition by feeling the engagement when it is moved through
all the positions. Check whether or not the actual pos ition the selector lever matches the position shown
by the shift position indicator and the A/T body.
5. The method of operating the lever to individual positions cor- rectly is shown in the figure.
6. When selector button is pressed in “P”, “R”, or “N” position with-
out applying forward/backward force to selector lever, check but-
ton operation for sticking.
7. Confirm that the back-up lamps illuminate only when lever is placed in the “R” position. Confirm that the back-up lamps do not
illuminate when selector lever is pushed against “R” position in
the “P” or “N” position.
8. Confirm that the engine can only be started with the selector lever in the “P” and “N” positions. (With selector lever in the “P”
position, engine can be started even when selector lever is
moved forward and backward.)
9. Make sure that A/T is locked completely in “P” position.
10. When selector lever is set to manual shift gate, ma ke sure that manual mode is displayed on combination
meter.
In addition, a set shift position must be changed when t he selector lever is shifted to the “+” or “−” side in
the manual mode. (Only while driving.)
AdjustmentINFOID:0000000006379166
1. Shift selector lever in “P” position.
2. Loosen nut (1).
3. Turn the manual lever (2) all the way in the “P” range direction
[ (A)].
4. Hold and push the control cable (3 ) in the vehicle front direction
[ (B)], and tighten the nut by hand with cable set in free condi-
tion.
CAUTION:
Be careful not put any load to manual lever.
NOTE:
Press control cable with a force of 9.8 N (approximately 1 kg, 2.2
lb).
5. Tighten nut to specified torque. Refer to TM-178, "
Exploded View".
JSDIA0790GB
JSDIA1587ZZ
Revision: 2010 May2011 QX56
Page 5216 of 5598
![INFINITI QX56 2011 Factory Service Manual
TM-128
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0740 TORQUE CONVERTER
P0740 TORQUE CONVERTER
DTC LogicINFOID:0000000006226836
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehi](/img/42/57033/w960_57033-5215.png "INFINITI QX56 2011 Factory Service Manual
TM-128
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0740 TORQUE CONVERTER
P0740 TORQUE CONVERTER
DTC LogicINFOID:0000000006226836
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehi")
TM-128
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0740 TORQUE CONVERTER
P0740 TORQUE CONVERTER
DTC LogicINFOID:0000000006226836
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Start the engine.
2. Select “MANU MODE SW”, “GEA R” and “VEHICLE SPEED” in “Data Monitor” in “TRANSMISSION”.
3. Drive vehicle and maintain the following conditions for 30 seconds or more.
NOTE:
Driving the vehicle uphill (increased engine load) will help maintain the driving conditions required for this
test.
4. Perform “Self Diagnostic Results” in “TRANSMISSION”. With GST
Follow the procedure “With CONSULT-III”.
Is
“P0740” detected?
YES >> Go to TM-128, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226837
1.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace the control valve & TCM. Refer to TM-182, "Exploded View".
NO >> Repair or replace damaged parts.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0740 Torque Converter Clutch Cir-
cuit/Open The torque converter clutch so-
lenoid valve monitor value is 0.4
A or less when the torque con-
verter clutch solenoid valve
command value is more than
0.75 A. Harness or connectors
(Solenoid valve circuit is
open or shorted.)
Torque converter clutch sole- noid valve
MANU MODE SW : ON
GEAR : 2nd
VEHICLE SPEED : 40 km/h (25 MPH) or more
Revision: 2010 May2011 QX56
Page 5217 of 5598
![INFINITI QX56 2011 Factory Service Manual
P0744 TORQUE CONVERTERTM-129
< DTC/CIRCUIT DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
P0744 TORQUE CONVERTER
DescriptionINFOID:0000000006226838
This malfunction is detected when the A](/img/42/57033/w960_57033-5216.png "INFINITI QX56 2011 Factory Service Manual
P0744 TORQUE CONVERTERTM-129
< DTC/CIRCUIT DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
P0744 TORQUE CONVERTER
DescriptionINFOID:0000000006226838
This malfunction is detected when the A")
P0744 TORQUE CONVERTERTM-129
< DTC/CIRCUIT DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
P0744 TORQUE CONVERTER
DescriptionINFOID:0000000006226838
This malfunction is detected when the A/T does not lock-up. This is not only caused by electrical malfunction
(circuits open or shorted) but also by mechanical malfunc tion such as control valve sticking, improper solenoid
valve operation, etc.
DTC LogicINFOID:0000000006226839
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Start the engine.
2. Select “MANU MODE SW”, “GEAR” and “VEHICLE SPEED” in “Data Monitor” in “TRANSMISSION”.
3. Drive vehicle and maintain the following conditions for 10 seconds or more. NOTE:
Driving the vehicle uphill (increased engine load) will hel p maintain the driving conditions required for this
test.
4. Perform “Self Diagnostic Resu lts” in “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is
“P0744” detected?
YES >> Go to TM-129, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226840
1.DETECT MALFUNCTIONING ITEM
Disassemble the A/T assembly to check component parts. Refer to TM-226, "
Disassembly".
NOTE:
Check the component parts, referring to “Possibl e cause” in “DTC DETECTION LOGIC”. Refer to TM-129,
"DTC Logic".
Is the inspection result normal?
YES >> Replace the control valve & TCM. Refer to TM-182, "Exploded View".
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0744 Torque Converter Clutch Circuit
Intermittent The lock-up is not performed in
spite of within the lock-up area. Harness or connectors
Torque converter clutch sole-
noid valve
Torque converter
Input speed sensor 1, 2
Hydraulic control circuit
MANU MODE SW : ON
GEAR : 2nd
VEHICLE SPEED : 40 km/h (25 MPH) or more
Revision: 2010 May2011 QX56
Page 5218 of 5598
![INFINITI QX56 2011 Factory Service Manual
TM-130
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0744 TORQUE CONVERTER
NO >> Repair or replace damaged parts.
Revision: 2010 May2011 QX56](/img/42/57033/w960_57033-5217.png "INFINITI QX56 2011 Factory Service Manual
TM-130
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0744 TORQUE CONVERTER
NO >> Repair or replace damaged parts.
Revision: 2010 May2011 QX56")
TM-130
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0744 TORQUE CONVERTER
NO >> Repair or replace damaged parts.
Revision: 2010 May2011 QX56
Page 5253 of 5598
![INFINITI QX56 2011 Factory Service Manual
SYSTEM SYMPTOMTM-165
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYMPTOM DIAGNOSIS
SYSTEM SYMPTOM
Symptom TableINFOID:0000000006226890
The diagnostics item numbers show the](/img/42/57033/w960_57033-5252.png "INFINITI QX56 2011 Factory Service Manual
SYSTEM SYMPTOMTM-165
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYMPTOM DIAGNOSIS
SYSTEM SYMPTOM
Symptom TableINFOID:0000000006226890
The diagnostics item numbers show the")
SYSTEM SYMPTOMTM-165
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYMPTOM DIAGNOSIS
SYSTEM SYMPTOM
Symptom TableINFOID:0000000006226890
The diagnostics item numbers show the sequence for inspection. Inspect in order from item 1.
Perform diagnoses of symptom table 1 before symptom table 2.
SYMPTOM TABLE 1
Symptom Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Poor
perfor-
mance
Driving
perfor-
manceShift point is high in “D” position. 1 2 3
Shift point is low in “D” position. 1 2
Large
shock
When
shifting
gears →
“D” position4 7665 32 31
→ “R” position 4 7 6 6 5 3 2 1
1GR ⇔ 2GR 4 2544 3 1
2GR ⇔ 3GR 4 2544 3 1
3GR ⇔ 4GR 4 2544 3 3 1
4GR ⇔ 5GR 4 2544 3 3 1
5GR ⇔ 6GR 4 2544 33 1
6GR ⇔ 7GR 4 2544 3 3 1
Downshift when
accelerator ped-
al is depressed 3 2433 1
Upshift when ac-
celerator pedal
is released 3 2433 1
Lock-up 4 2444 3 1
Judder Lock-up 2 1 1 4 3
Strange noise In “R” position 2 1
In “N” position 2 1
In “D” position 2 1
Engine at idle 2 1
Revision: 2010 May2011 QX56
Page 5254 of 5598
![INFINITI QX56 2011 Factory Service Manual
TM-166
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
SymptomDiagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input spe](/img/42/57033/w960_57033-5253.png "INFINITI QX56 2011 Factory Service Manual
TM-166
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
SymptomDiagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input spe")
TM-166
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
SymptomDiagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Func-
tion
trouble
Gear
does no
change “D” position Locks in 1GR 1 1 1 1
Locks in 2GR
Locks in 3GR
Locks in 4GR
Locks in 5GR 1
Locks in 6GR
Locks in 7GR
1GR
→ 2GR 1 1 1 1
2GR → 3GR 1
3GR → 4GR 2 22 2222 1
4GR → 5GR 1 1
5GR → 6GR 1
6GR → 7GR 1 1 1 1 1
5GR → 4GR 1
4GR → 3GR 1 1 1
3GR → 2GR 1 1
2GR → 1GR 1 1 1
Does not lock-up 2 22245 32222222 2 2 1
“M” posi-
tion 1GR
⇔ 2GR 3 33 32 3333333 3 3 1
2GR ⇔ 3GR 3 33 32 3333333 3 3 1
3GR ⇔ 4GR 3 33 32 3333333 3 3 1
4GR ⇔ 5GR 3 33 32 3333333 3 3 1
5GR ⇔ 6GR 3 33 32 3333333 3 3 1
6GR ⇔ 7GR 3 33 32 3333333 3 3 1
Revision: 2010 May2011 QX56
Page 5255 of 5598
![INFINITI QX56 2011 Factory Service Manual
SYSTEM SYMPTOMTM-167
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Symptom Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sen](/img/42/57033/w960_57033-5254.png "INFINITI QX56 2011 Factory Service Manual
SYSTEM SYMPTOMTM-167
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Symptom Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sen")
SYSTEM SYMPTOMTM-167
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Symptom Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter clutch solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Func-
tion trou-
ble
Poor
shiftingSlip
When
shifting
gears1GR
⇔ 2GR 3 3 3 4 2 2 1
2GR ⇔ 3GR 3 3 3 4 2 2 1
3GR ⇔ 4GR 3 3 3 4 2 2 2 2 1
4GR ⇔ 5GR 3 3 3 4 2 2 2 1
5GR ⇔ 6GR 3 3 3 4 2 2 2 1
6GR ⇔ 7GR 3 3 3 4 2 2 2 1
Engine
brake
does
not
work “D” position
→ “M” posi-
tion 5556423 33 1
“M” po-
sition 7GR
→ 6GR 5 5 5 6 4 2 3 3 3 1
6GR → 5GR 5 5 5 6 4 2 3 3 3 1
5GR → 4GR 5 5 5 6 4 2 3 3 3 1
4GR → 3GR 5 5 5 6 4 2 3 3 3 3 1
3GR → 2GR 5 556423 33 1
2GR → 1GR 5 5 5 6 4 2 3 3 3 1
Revision: 2010 May2011 QX56
Page 5256 of 5598
![INFINITI QX56 2011 Factory Service Manual
TM-168
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
Func-
tion trou-
blePoor
power
trans-
mission
Slip With selector
lever in “D”
position, ac-
celeration is
extremely
poor.
53 334 2](/img/42/57033/w960_57033-5255.png "INFINITI QX56 2011 Factory Service Manual
TM-168
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
Func-
tion trou-
blePoor
power
trans-
mission
Slip With selector
lever in “D”
position, ac-
celeration is
extremely
poor.
53 334 2")
TM-168
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
Func-
tion trou-
blePoor
power
trans-
mission
Slip With selector
lever in “D”
position, ac-
celeration is
extremely
poor.
53 334 2 2 2 1
With selector
lever in “R”
position, ac-
celeration is
extremely
poor. 53 334 2 2 2 1
While starting
off by acceler-
ating in 1GR,
engine races. 3 334 2 2 2 1
While acceler-
ating in 2GR,
engine races. 3 334 2 2 22 1
While acceler-
ating in 3GR,
engine races. 3 334 2 2 22 1
While acceler-
ating in 4GR,
engine races. 3 334 2 2 22 1
While acceler-
ating in 5GR,
engine races. 3 334 2 222 2 1
While acceler-
ating in 6GR,
engine races. 3 334 2 22221
While acceler-
ating in 7GR,
engine races. 3 334 2 2 22 2 1
Lock-up 3 334 2 2 1
No creep at
all. 111111111
Extremely
large creep. 1
Symptom
Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter clutch solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Revision: 2010 May2011 QX56
Page 5257 of 5598
![INFINITI QX56 2011 Factory Service Manual
SYSTEM SYMPTOMTM-169
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYMPTOM TABLE 2
Symptom Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pe](/img/42/57033/w960_57033-5256.png "INFINITI QX56 2011 Factory Service Manual
SYSTEM SYMPTOMTM-169
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYMPTOM TABLE 2
Symptom Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pe")
SYSTEM SYMPTOMTM-169
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYMPTOM TABLE 2
Symptom Diagnostic item
Control cable
Output speed sensor
Vehicle speed signal
Accelerator pedal position sensor
Engine speed signal
Input speed sensor
A/T fluid temperature sensor
Battery voltage
Transmission range switch
Manual mode switch
Stop lamp switch
Line pressure solenoid valve
Torque converter clutch solenoid valve
Low brake solenoid valve
Front brake solenoid valve
High and low reverse clutch solenoid valve
Input clutch solenoid valve
Direct clutch solenoid valve
2346 brake solenoid valve
Anti-interlock solenoid valve
Starter relay
CAN communication
TM-101
TM-110TM-138TM-137TM-112TM-109TM-107TM-151TM-106TM-144TM-159TM-131TM-128TM-148TM-136TM-147TM-133TM-150TM-149TM-132TM-104TM-103
Function
trouble
Power transmis-
sion cannot be
performed Vehicle cannot run in all
position.
3 2 111111111
Driving is not possible in
“D” position. 3 2 111111111
Driving is not possible in
“R” position. 32111
Engine stall 4 5 5 6 3 2 1
Engine stalls when selec-
tor lever shifted “N” → “D”
or “R”. 455 3 2 1
Engine does not start in
“N” or “P” position. 312 1
Engine starts in position
other than “N” or “P”. 32 1
Poor operation Vehicle does not enter
parking condition.
12
Parking condition is not
cancelled. 12
Vehicle runs with A/T in
“P” position. 12
Vehicle moves forward
with the “R” position. 12
Vehicle runs with A/T in
“N” position. 12
Vehicle moves backward
with the “D” position. 12
Revision: 2010 May2011 QX56