torque INFINITI QX56 2011 Factory Service Manual

TM-170
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
*: Parts behind drum support is impossible to perform inspection by disassembly. Refer to
TM-16, "TRANSMISSION : Cross-Sectional
View".Symptom
Diagnostic item
Oil pump
Torque converter
Low brake*
Front brake
High and low reverse clutch
Input clutch
Direct clutch
2346 brake
Reverse brake
1st one-way clutch
2nd one-way clutch
gear
control valve
Parking component
TM-270
TM-211TM-211TM-211TM-292TM-282TM-294TM-270TM-211TM-211TM-287TM-211TM-182TM-211
Poor
perfor-
mance
Driving
perfor-
mance Shift point is high in “D” position.
Shift point is low in “D” position.
Large
shock
When
shifting
gears →
“D” position 1 2 2
→ “R” position 1 1 2
1GR ⇔ 2GR 1 2
2GR ⇔ 3GR 1 2
3GR ⇔ 4GR 2 1 2
4GR ⇔ 5GR 1 1 2
5GR ⇔ 6GR 1 1 2
6GR ⇔ 7GR 1 1 2
Downshift when accel-
erator pedal is de-
pressed 211111 11 2
Upshift when accelera-
tor pedal is released 211111 11 2
Lock-up 1 2
Judder Lock-up 1 2
Strange noise In “R” position 1 1 1 1 2
In “N” position 1 1 1 2
In “D” position 1 1 1 1 2
Engine at idle 1 1 1 2
Revision: 2010 May2011 QX56

SYSTEM SYMPTOMTM-171
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
*: Parts behind drum support is impossible to perform inspection by disassembly. Refer to TM-16, "TRANSMISSION : Cross-Sectional
View".Symptom
Diagnostic item
Oil pump
Torque converter
Low brake*
Front brake
High and low reverse clutch
Input clutch
Direct clutch
2346 brake
Reverse brake
1st one-way clutch
2nd one-way clutch
gear
control valve
Parking component
TM-270
TM-211TM-211TM-211TM-292TM-282TM-294TM-270TM-211TM-211TM-287TM-211TM-182TM-211
Func-
tion
trouble
Gear
does no
change“D” posi-
tion Locks in 1GR 1 1 1 2
Locks in 2GR
1
Locks in 3GR 1
Locks in 4GR 1
Locks in 5GR 1
Locks in 6GR 1
Locks in 7GR 1
1GR → 2GR 1 1 1 2
2GR → 3GR 1 2
3GR → 4GR 2111 2
4GR → 5GR 1 1 2
5GR → 6GR 1 2
6GR → 7GR 2111 2
5GR → 4GR 1 2
4GR → 3GR 2 1 2
3GR → 2GR 1 1 2
2GR → 1GR 1 1 1 2
Does not lock-up 1211111 11 2
“M” posi-
tion 1GR
⇔ 2GR 211111 11 2
2GR ⇔ 3GR 211111 11 2
3GR ⇔ 4GR 211111 11 2
4GR ⇔ 5GR 211111 11 2
5GR ⇔ 6GR 211111 11 2
6GR ⇔ 7GR 211111 11 2
Revision: 2010 May2011 QX56

TM-172
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
SymptomDiagnostic item
Oil pump
Torque converter
Low brake*
Front brake
High and low reverse clutch
Input clutch
Direct clutch
2346 brake
Reverse brake
1st one-way clutch
2nd one-way clutch
gear
control valve
Parking component
TM-270
TM-211TM-211TM-211TM-292TM-282TM-294TM-270TM-211TM-211TM-287TM-211TM-182TM-211
Func-
tion
trouble
Poor
shift-
ingSlip
When
shifting
gears 1GR
⇔ 2GR 1 1 1 2
2GR ⇔ 3GR 1 1 2
3GR ⇔ 4GR 1 2 1 2
4GR ⇔ 5GR 1 1 1 2
5GR ⇔ 6GR 1 1 1 2
6GR ⇔ 7GR 1 1 1 2
En-
gine
brake
does
not
work “D” position
→ “M” position 1 1 1 1 1 2
“M” posi-
tion 7GR
→ 6GR 1 1 1 2
6GR → 5GR 1 1 1 2
5GR → 4GR 1 1 1 2
4GR → 3GR 1 2 1 2
3GR → 2GR 1 1 1 1 1 2
2GR → 1GR 1 1 1 1 2
Revision: 2010 May2011 QX56

SYSTEM SYMPTOMTM-173
< SYMPTOM DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
*: Parts behind drum support is impossible to perform inspection by disassembly. Refer to TM-16, "TRANSMISSION : Cross-Sectional
View".
Func-
tion
trouble
Poor
pow-
er
trans-
mis-
sion
Slip With selector lever
in “D” position, ac-
celeration is ex-
tremely poor.
112 1 12
With selector lever
in “R” position, ac-
celeration is ex-
tremely poor. 11 11112
While starting off
by accelerating in
1GR, engine rac-
es. 112 1112
While accelerating
in 2GR, engine
races. 1 2 1 112
While accelerating
in 3GR, engine
races. 1 2 11 12
While accelerating
in 4GR, engine
races. 1 1 11 12
While accelerating
in 5GR, engine
races. 1 111 12
While accelerating
in 6GR, engine
races. 111112
While accelerating
in 7GR, engine
races. 1 111 2
Lock-up 1 1 1 2
No creep at all. 11211111 11121
Extremely large
creep. 1
Symptom
Diagnostic item
Oil pump
Torque converter
Low brake*
Front brake
High and low reverse clutch
Input clutch
Direct clutch
2346 brake
Reverse brake
1st one-way clutch
2nd one-way clutch
gear
control valve
Parking component
TM-270
TM-211TM-211TM-211TM-292TM-282TM-294TM-270TM-211TM-211TM-287TM-211TM-182TM-211
Revision: 2010 May2011 QX56

TM-174
< SYMPTOM DIAGNOSIS >[7AT: RE7R01B]
SYSTEM SYMPTOM
*: Parts behind drum support is impossible to perform inspection by disassembly. Refer to
TM-16, "TRANSMISSION : Cross-Sectional
View".Symptom
Diagnostic item
Oil pump
Torque converter
Low brake*
Front brake
High and low reverse clutch
Input clutch
Direct clutch
2346 brake
Reverse brake
gear
1st one-way clutch
2nd one-way clutch
control valve
Parking component
TM-270
TM-211TM-211TM-211TM-292TM-282TM-294TM-270TM-211TM-211TM-287TM-211TM-182TM-211
Function
trouble
Power trans-
mission cannot
be performed
Vehicle cannot run in all position. 1 1 2 1 1 1 1 1 1 2 1
Driving is not possible in “D” posi-
tion.
11211111 11121
Driving is not possible in “R” posi-
tion. 1 111121
Engine stall 1
Engine stalls when selector lever
shifted “N” → “D” or “R”. 1
Engine does not start in “N” or “P”
position. 1
Engine starts in position other
than “N” or “P”.
Poor operation Vehicle does not enter parking
condition.
1
Parking condition is not cancelled. 1
Vehicle runs with A/T in “P” posi-
tion. 2111111 21
Vehicle moves forward with the
“R” position. 211111 2
Vehicle runs with A/T in “N” posi-
tion. 2111111 2
Vehicle moves backward with the
“D” position. 12
Revision: 2010 May2011 QX56

CONTROL VALVE & TCMTM-185
< REMOVAL AND INSTALLATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
CAUTION:
 Make sure that turbine revolution sensor securely installs input speed sensor holes (A).
 Hang down output speed senso r harness toward outside so
as not to disturb installation of the control valve & TCM.
 Adjust A/T assembly harness connector of the control valve
& TCM to terminal hole of transmission case.
 Assemble it so that manual valve (1) cutout is engaged with manual plate (2) projection.
- Install bolts and clip (1) to the control valve & TCM. Tighten bolt (E) to the specified torque before tightening the other than bolts.
*: Reamer bolt
 Refer to the following when installing oil pan to transmission case.CAUTION:
 Clean foreign materials (gear wear particles) that adhere on the inside of the oil pan and on the
magnet, and then assembly.
 Completely remove all moisture, oil and old gasket, etc. from oil pan gasket mounting surface of
transmission case and oil pan.
 Never reuse oil pan gasket and oil pan mounting bolts.
 Install oil pan gasket in the di rection to align hole position.
- Tighten the oil pan mounting bolts to the specified torque in the numerical order as shown in the figure after temporarily tightening
them.
JPDIA1106ZZ
JPDIA0012ZZ
: Vehicle front
Bolt symbol Length mm (in) Number of bolts A 43 (1.69) 3
B 40 (1.57) 2
C 54 (2.13) 6
D 50 (1.97) 2
E* 50 (1.97) 1
: Vehicle front
JPDIA1105ZZ
JSDIA1592GB
Revision: 2010 May2011 QX56

TM-190
< REMOVAL AND INSTALLATION >[7AT: RE7R01B]
PARKING COMPONENTS
16. Remove return spring (1) from parking pawl (2).
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
 Never reuse seal rings and drain plug gasket.
 Apply petroleum jelly to n
eedle bearing and seal rings.
 Insert the tip of parking rod between the parki ng pawl and the parking actuator support when assem-
bling the rear extension assembly.
 Refer to the followings installing rear extension assembly.
- Apply recommended sealant (Genuine Anaerobic Liquid Gasket or
equivalent. Refer to GI-22, "
Recommended Chemical Products
and Sealants".) to rear extension assembly as shown in the figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc. from
the transmission case and rear extension assembly mounting
surfaces.
- Tighten rear extension assembly bolts to the specified torque.
2WD : InspectionINFOID:0000000006233260
INSPECTION AFTER REMOVAL
SCIA6180J
Sealant starting
point and end-
point (A) : Start and finish
point shall be in
the center of two bolts.
Overlap width of
sealant starting
point and end-
point (B) : 3 – 5 mm (0.12 – 0.20 in)
Sealant width (C) : 1.0 – 2.0 mm (0.04 – 0.08 in)
Sealant height (C) : 0.4 – 1.0 mm (0.016 – 0.04 in)
JSDIA1855ZZ
1: Bracket
A: Bolt
B : Self-sealing bolt
JSDIA1845ZZ
Revision: 2010 May2011 QX56

TM-198
< REMOVAL AND INSTALLATION >[7AT: RE7R01B]
OUTPUT SPEED SENSOR
- Tighten rear extension assembly bolts to the specified torque.
 Refer to the followings when installing oil pan (2) (with oil pan gas-
ket) and clips (1) to transmission case.
CAUTION:
 Never reuse oil pan gasket and oil pan mounting bolts.
 Install oil pan gasket in the di rection to align hole position.
 Install it so that drain plug comes to the position as shown
in the figure.
 Be careful not to pinch harnesses.
 Completely remove all moisture, oil and ol d gasket, etc. from oil pan mounting surface.
- Tighten oil pan mounting bolts to the specified torque in numerical
order shown in the figure after temporarily tightening them. Tighten
necessary oil pan mounting bolts with specified torque.
2WD : Inspection and AdjustmentINFOID:0000000006228121
INSPECTION AFTER REMOVAL
Check foreign materials in oil pan to help determine causes of mal-
function. If the ATF is very dark, smells burned, or contains foreign
particles, the frictional material (clutches, band) may need replace-
ment. A tacky film that will not wipe clean indicates varnish build up.
Varnish can cause valves, servo, and clutches to stick and can
inhibit pump pressure.
If frictional material is det ected, perform A/T fluid cooler
cleaning. Refer to TM-97, "
Cleaning".
INSPECTION AFTER INSTALLATION
Check A/T fluid leakage Refer to TM-175, "Inspection".
1: Bracket
A: Bolt
B : Self-sealing bolt
JSDIA1845ZZ
: Vehicle front
: Oil pan mounting bolt
: Vehicle front
JSDIA1591ZZ
JSDIA1592GB
SCIA5199E
Revision: 2010 May2011 QX56

TM-206
< UNIT REMOVAL AND INSTALLATION >[7AT: RE7R01B]
TRANSMISSION ASSEMBLY
8. Remove exhaust front tube (RH and LH) and main muffler. Refer to
EX-5, "Exploded View".
9. Separate propeller shaft assembly. Refer to DLN-144, "
Removal and Installation".
NOTE:
Cap or plug opening to prevent fluid from spilling.
10. Remove front under cover with a power tool. Refer to EXT-25, "
Removal and Installation".
11. Remove protector A and B. Refer to SCS-32, "
FRONT TUBE ASSEMBLY : Exploded View".
12. Remove front suspension rear cross member.
13. Remove crankshaft position sensor (POS) from A/T assembly. Refer to EM-106, "
Exploded View".
CAUTION:
 Never subject it to impact by dropping or hitting it.
 Never disassemble.
 Never allow metal filings, etc. to ge t on the sensor's front edge magnetic area.
 Never place in an area affected by magnetism.
14. Remove rear plate cover. Refer to EM-54, "
Exploded View".
15. Turn crankshaft, and remove the four tight ening bolts for drive plate and torque converter.
CAUTION:
When turning the crankshaft, turn it clockw ise as viewed from the front of the engine.
16. Remove A/T fluid cooler tube A and D. Refer to TM-202, "
Exploded View".
NOTE:
Cap or plug openings to prevent fluid from spilling.
17. Remove bolts fixing A/T assembly to engine with a power tool.
18. Disconnect connector from A/T assembly.
19. Remove harness and brackets from A/T assembly.
20. Remove A/T assembly from the vehicle. CAUTION:
 Secure torque converter to prevent it from dropping.
 Secure A/T assembly to a transmission jack.
21. Remove air breather hose and bracket. Refer to TM-199, "
2WD
: Exploded View".
22. Remove manual lever from A/T assembly. Refer to TM-178,
"Exploded View".
INSTALLATION
Note the following, and Install in the reverse order of removal.
 Check fitting of dowel pin ( ).
ATA0025D
JSDIA1597ZZ
Revision: 2010 May2011 QX56

TRANSMISSION ASSEMBLYTM-207
< UNIT REMOVAL AND INSTALLATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
 When installing A/T assembly to the engine, be sure to check dimension “A” to ensure it is within the reference value limit.
 When installing A/T assembly to the engine, attach the fixing bolts in accordance with the following standard.
*: Tightening the bolt with bracket (and washer). Refer to TM-199, "2WD : Exploded View".
 Align the positions of tightening bolts for drive plate with those of the torque converter, and temporarily
tighten the bolts. Then, tighten the bolts with the specified torque.
CAUTION:
 When turning crankshaft, turn it clockwise as viewed from the front of the engine.
 When tightening the tightening bolts for the torq ue converter after fixing the crankshaft pulley
bolts, be sure to confirm the tightening torque of the crankshaft pulley mounting bolts. Refer to
EM-62, "
Removal and Installation".
 Rotate crankshaft several turns and check to be sure that A/T rotates freely without binding after
converter is installed to drive plate.
2WD : Inspection and AdjustmentINFOID:0000000006233265
INSPECTION AFTER INSTALLATION
 Check A/T fluid leakage. Refer to TM-175, "Inspection".
 Check A/T position after adjusting A/T position. Refer to TM-101, "
Inspection".
ADJUSTMENT AFTER INSTALLATION
 Adjust A/T fluid level. Refer to TM-95, "Adjustment".
 Adjust A/T position. Refer to TM-101, "
Adjustment".
 Perform decel G sensor calibration when replacing A/T assembly. Refer to TM-91, "
Special Repair Require-
ment".
4WD
B: Scale
C : Straightedge
Dimension “A” : Refer to TM-297, "Torque Convert-
er".
JPDIA0042ZZ
Bolt symbol A
Insertion direction A/T assembly to engine
Number of bolts 9
Bolt length “L”
mm (in) 70 (2.76)
Tightening torque
N·m (kg-m, ft-lb) 113 (12, 83)
JSDIA1598ZZ
Revision: 2010 May2011 QX56