brake sensor INFINITI QX56 2011 Factory Service Manual

TM-64
< SYSTEM DESCRIPTION >[7AT: RE7R01B]
DIAGNOSIS SYSTEM (TCM)
TRG PRE 2346/B
(kPa, kg/cm2 or psi)—— Displays the target oil pressure value of 2346
brake solenoid valve calculated by the oil pres-
sure calculation process of shift change control.
SHIFT PATTERN — — Displays the gear change data using the shift
pattern control.
VEHICLE SPEED (km/h or mph) — — Displays the vehicle speed for control using the
control of TCM.
G SEN SLOPE (%) X — Displays the inclination angle calculated by the
G sensor signal received via CAN communica-
tion.
RANGE SW 4 (ON/OFF) X — Displays the operation status of transmission
range switch 4.
RANGE SW 3 (ON/OFF) X — Displays the operation status of transmission
range switch 3.
RANGE SW 2 (ON/OFF) X — Displays the operation status of transmission
range switch 2.
RANGE SW 1 (ON/OFF) X — Displays the operation status of transmission
range switch 1.
SFT DWN ST SW (ON/OFF) X —  Displays the operation status of paddle
shifter (down switch).
 Not mounted but displayed.
SFT UP ST SW (ON/OFF) X —  Displays the operation status of paddle
shifter (up switch).
 Not mounted but displayed.
DOWN SW LEVER (ON/OFF) X — Displays the operation status of selector lever
(down switch).
UP SW LEVER (ON/OFF) X — Displays the operation status of selector lever
(up switch).
NON M-MODE SW (ON/OFF) X — Displays whether the selector lever is in any po-
sition other than manual shift gate position.
MANU MODE SW (ON/OFF) X — Displays whether the selector lever is in the
manual shift gate position.
TOW MODE SW (ON/OFF) — — Displays the reception status of tow mode
switch signal received via CAN communication.
DS RANGE (ON/OFF) — —  Displays whether it is the DS mode.
 Not mounted but displayed.
1 POSITION SW (ON/OFF) X —  Displays the reception status of 1 position
switch signal received via CAN communica-
tion.
 Not mounted but displayed.
OD CONT SW (ON/OFF) X —  Displays the reception status of overdrive
control switch signal received via CAN com-
munication.
 Not mounted but displayed.
BRAKESW (ON/OFF) X — Displays the reception status of stop lamp
switch signal received via CAN communication.
POWERSHIFT SW (ON/OFF) X —  Displays the reception status of POWER
mode signal received via CAN communica-
tion.
 Not mounted but displayed.
Monitored item (Unit)
Monitor Item Selection
Remarks
ECU IN-
PUT SIG- NALS MAIN SIG-
NALS SELEC-
TION
FROM ITEM
Revision: 2010 May2011 QX56

DIAGNOSIS SYSTEM (TCM)TM-67
< SYSTEM DESCRIPTION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
Item name Description Check item
1ST GR FNCTN P0731 Following items for “1GR incorrect ratio” can be confirmed.
 Self-diagnosis status (whether the diagnosis is being performed or not)
 Self-diagnostic results (OK or NG)
 Input clutch solenoid
valve
 Front brake solenoid
valve
 Direct clutch solenoid valve
 High and low reverse clutch solenoid valve
 Low brake solenoid
valve
 2346 brake solenoid valve
 Anti-interlock sole- noid valve
 Each clutch and brake
 Output speed sensor
 Input speed sensor 1, 2
 Hydraulic control cir- cuit
2ND GR FNCTN P0732
Following items for “2GR incorrect ratio” can be confirmed.
 Self-diagnosis status (whether the diagnosis is being performed or not)
 Self-diagnostic results (OK or NG)
3RD GR FNCTN P0733 Following items for “3GR incorrect ratio” can be confirmed.
 Self-diagnosis status (whether the diagnosis is being performed or not)
 Self-diagnostic results (OK or NG)
4TH GR FNCTN P0734 Following items for “4GR incorrect ratio” can be confirmed.
 Self-diagnosis status (whether the diagnosis is being performed or not)
 Self-diagnostic results (OK or NG)
5TH GR FNCTN P0735 Following items for “5GR incorrect ratio” can be confirmed.
 Self-diagnosis status (whether the diagnosis is being performed or not)
 Self-diagnostic results (OK or NG)
6TH GR FNCTN P0729 Following items for “6GR incorrect ratio” can be confirmed.
 Self-diagnosis status (whether the diagnosis is being performed or not)
 Self-diagnostic results (OK or NG)
7TH GR FNCTN P1734 Following items for “7GR incorrect ratio” can be confirmed.
 Self-diagnosis status (whether the diagnosis is being performed or not)
 Self-diagnostic results (OK or NG)
TCC SOL FUNCTN CHECK Following items for “TCC solenoid function” can be confirmed.
 Self-diagnosis status (whether the diagnosis is being performed or not)
 Self-diagnostic results (OK or NG)  Harness or connec-
tors
 Torque converter
clutch solenoid valve
 Torque converter
 Input speed sensor 1, 2
 Hydraulic control cir- cuit
Revision: 2010 May2011 QX56

TM-114
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0729 6GR INCORRECT RATIO
P0729 6GR INCORRECT RATIO
DescriptionINFOID:0000000006226815
This malfunction is detected when the A/T does not shift
into 6GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or s horted) but by mechanical malfunction such as control
valve sticking, improper solenoid valve operation, etc.
DTC LogicINFOID:0000000006226816
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
“ TM-115, "
Diagnosis Procedure"” must be performed before starting “DTC CONFIRMATION PROCE-
DURE”.
 Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause secondary malfunction.
 Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK ATF TEMPERATURE
With CONSULT-III
1. Start the engine.
2. Select “ATF TEMP 1” in “Data Monitor” in “TRANSMISSION”.
3. Check ATF temperature is in the following range.
With GST
1. Start the engine.
2. Drive vehicle for approximately 5 minutes in urban areas.
Is ATF temperature within specified range?
YES >> GO TO 3.
NO >> Drive vehicle to warm ATF or stop engine to cool ATF.
3.CHECK SYMPTOM (PART 1)
With CONSULT-III
1. Select “6TH GR FNCTN P0729” in “DTC & SRT confirmation” in “TRANSMISSION”.
2. Drive vehicle with manual mode and maintain the following conditions.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0729 Gear 6 Incorrect Ratio The gear ratio is:
 0.915 or more
 0.813 or less Input clutch solenoid valve
 Direct clutch solenoid valve
 High and low reverse clutch
solenoid valve
 Front brake solenoid valve
 Low brake solenoid valve
 2346 brake solenoid valve
 Anti-interlock solenoid valve
 Each clutch and brake
 Output speed sensor
 Input speed sensor 1, 2
 Hydraulic co ntrol circuit
ATF TEMP 1 : 20 °C (68 °F) – 140 °C (284 °F)
Revision: 2010 May2011 QX56

TM-116
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0730 INCORRECT GEAR RATIO
P0730 INCORRECT GEAR RATIO
DescriptionINFOID:0000000006226818
 TCM detects a high-rpm state of the under drive sun gear.
 The number of revolutions of the under drive sun gear
is calculated with the input speed sensor 1 and 2.
DTC LogicINFOID:0000000006226819
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
“TM-116, "
Diagnosis Procedure"” must be performed before starting “DTC CONFIRMATION PROCE-
DURE”.
 Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause secondary malfunction.
 Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Start the engine.
2. Select “Self Diagnostic Results” in “ENGINE”.
3. Drive vehicle under the similar conditions to (1st trip) Freeze Frame Data for 10 minutes. Refer to the
table below.
Hold the accelerator pedal as steady as possible.
With GST
Follow the procedure “With CONSULT-III”.
Is
“P0730” detected?
YES >> Go to TM-116, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226820
1.DETECT MALFUNCTIONING ITEM
Disassemble the A/T assembly to check component parts. Refer to TM-211, "
Exploded View".
NOTE:
Check the component parts, referring to “Possible cause” in “DTC DETECTION LOGIC”. Refer to TM-116,
"DTC Logic".
Is the inspection result normal?
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0730 Incorrect Gear Ratio The revolution of under drive
sun gear is 8,000 rpm or more.
NOTE:
Not detected when in “P” or “N”
position and during a shift to “P”
or “N” position. 2346 brake solenoid valve
 Front brake solenoid valve
 Input speed sensor 2
ENGINE SPEED Same value as
the Freeze Frame Data.
VEHICLE SPEED Same value as the Freeze Frame Data.
B/FUEL SCHDL Same value as the Freeze Frame Data.
Revision: 2010 May2011 QX56

TM-118
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0731 1GR INCORRECT RATIO
P0731 1GR INCORRECT RATIO
DescriptionINFOID:0000000006226821
This malfunction is detected when the A/T does not shift
into 1GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or s horted) but by mechanical malfunction such as control
valve sticking, improper solenoid valve operation, etc.
DTC LogicINFOID:0000000006226822
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
“ TM-119, "
Diagnosis Procedure"” must be performed before starting “DTC CONFIRMATION PROCE-
DURE”.
 Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause secondary malfunction.
 Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK ATF TEMPERATURE
With CONSULT-III
1. Start the engine.
2. Select “ATF TEMP 1” in “Data Monitor” in “TRANSMISSION”.
3. Check ATF temperature is in the following range.
With GST
1. Start the engine.
2. Drive vehicle for approximately 5 minutes in urban areas.
Is ATF temperature within specified range?
YES >> GO TO 3.
NO >> Drive vehicle to warm ATF or stop engine to cool ATF.
3.CHECK SYMPTOM (PART 1)
With CONSULT-III
1. Select “1ST GR FNCTN P0731” in “DTC & SRT confirmation” in “TRANSMISSION”.
2. Drive vehicle with manual mode and maintain the following conditions.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0731 Gear 1 Incorrect Ratio The gear ratio is:
 5.180 or more
 4.594 or less Input clutch solenoid valve
 Direct clutch solenoid valve
 High and low reverse clutch
solenoid valve
 Front brake solenoid valve
 Low brake solenoid valve
 2346 brake solenoid valve
 Anti-interlock solenoid valve
 Each clutch and brake
 Output speed sensor
 Input speed sensor 1, 2
 Hydraulic co ntrol circuit
ATF TEMP 1 : 20 °C (68 °F) – 140 °C (284 °F)
Revision: 2010 May2011 QX56

TM-120
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0732 2GR INCORRECT RATIO
P0732 2GR INCORRECT RATIO
DescriptionINFOID:0000000006226824
This malfunction is detected when the A/T does not shift
into 2GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or s horted) but by mechanical malfunction such as control
valve sticking, improper solenoid valve operation, etc.
DTC LogicINFOID:0000000006226825
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
“ TM-121, "
Diagnosis Procedure"” must be performed before star ting “DTC CONFIRMATION PROCE-
DURE”.
 Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause secondary malfunction.
 Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK ATF TEMPERATURE
With CONSULT-III
1. Start the engine.
2. Select “ATF TEMP 1” in “Data Monitor” in “TRANSMISSION”.
3. Check ATF temperature is in the following range.
With GST
1. Start the engine.
2. Drive vehicle for approximately 5 minutes in urban areas.
Is ATF temperature within specified range?
YES >> GO TO 3.
NO >> Drive vehicle to warm ATF or stop engine to cool ATF.
3.CHECK SYMPTOM (PART 1)
With CONSULT-III
1. Select “2ND GR FNCTN P0732” in “DTC & SRT confirmation” in “TRANSMISSION”.
2. Drive vehicle with manual mode and maintain the following conditions.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0732 Gear 2 Incorrect Ratio The gear ratio is:
 3.360 or more
 2.980 or less Input clutch solenoid valve
 Direct clutch solenoid valve
 High and low reverse clutch
solenoid valve
 Front brake solenoid valve
 Low brake solenoid valve
 2346 brake solenoid valve
 Anti-interlock solenoid valve
 Each clutch and brake
 Output speed sensor
 Input speed sensor 1, 2
 Hydraulic control circuit
ATF TEMP 1 : 20 °C (68 °F) – 140 °C (284 °F)
Revision: 2010 May2011 QX56

TM-122
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0733 3GR INCORRECT RATIO
P0733 3GR INCORRECT RATIO
DescriptionINFOID:0000000006226827
This malfunction is detected when the A/T does not shift
into 3GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or s horted) but by mechanical malfunction such as control
valve sticking, improper solenoid valve operation, etc.
DTC LogicINFOID:0000000006226828
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
“ TM-123, "
Diagnosis Procedure"” must be performed before star ting “DTC CONFIRMATION PROCE-
DURE”.
 Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause secondary malfunction.
 Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK ATF TEMPERATURE
With CONSULT-III
1. Start the engine.
2. Select “ATF TEMP 1” in “Data Monitor” in “TRANSMISSION”.
3. Check ATF temperature is in the following range.
With GST
1. Start the engine.
2. Drive vehicle for approximately 5 minutes in urban areas.
Is ATF temperature within specified range?
YES >> GO TO 3.
NO >> Drive vehicle to warm ATF or stop engine to cool ATF.
3.CHECK SYMPTOM (PART 1)
With CONSULT-III
1. Select “3RD GR FNCTN P0733” in “DTC & SRT confirmation” in “TRANSMISSION”.
2. Drive vehicle with manual mode and maintain the following conditions.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0733 Gear 3 Incorrect Ratio The gear ratio is:
 2.148 or more
 1.906 or less Input clutch solenoid valve
 Direct clutch solenoid valve
 High and low reverse clutch
solenoid valve
 Front brake solenoid valve
 Low brake solenoid valve
 2346 brake solenoid valve
 Anti-interlock solenoid valve
 Each clutch and brake
 Output speed sensor
 Input speed sensor 1, 2
 Hydraulic control circuit
ATF TEMP 1 : 20 °C (68 °F) – 140 °C (284 °F)
Revision: 2010 May2011 QX56

TM-124
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0734 4GR INCORRECT RATIO
P0734 4GR INCORRECT RATIO
DescriptionINFOID:0000000006226830
This malfunction is detected when the A/T does not shift
into 4GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or s horted) but by mechanical malfunction such as control
valve sticking, improper solenoid valve operation, etc.
DTC LogicINFOID:0000000006226831
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
“ TM-125, "
Diagnosis Procedure"” must be performed before star ting “DTC CONFIRMATION PROCE-
DURE”.
 Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause secondary malfunction.
 Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK ATF TEMPERATURE
With CONSULT-III
1. Start the engine.
2. Select “ATF TEMP 1” in “Data Monitor” in “TRANSMISSION”.
3. Check ATF temperature is in the following range.
With GST
1. Start the engine.
2. Drive vehicle for approximately 5 minutes in urban areas.
Is ATF temperature within specified range?
YES >> GO TO 3.
NO >> Drive vehicle to warm ATF or stop engine to cool ATF.
3.CHECK SYMPTOM (PART 1)
With CONSULT-III
1. Select “4TH GR FNCTN P0734” in “DTC & SRT confirmation” in “TRANSMISSION”.
2. Drive vehicle with manual mode and maintain the following conditions.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0734 Gear 4 Incorrect Ratio The gear ratio is:
 1.496 or more
 1.328 or less Input clutch solenoid valve
 Direct clutch solenoid valve
 High and low reverse clutch
solenoid valve
 Front brake solenoid valve
 Low brake solenoid valve
 2346 brake solenoid valve
 Anti-interlock solenoid valve
 Each clutch and brake
 Output speed sensor
 Input speed sensor 1, 2
 Hydraulic co ntrol circuit
ATF TEMP 1 : 20 °C (68 °F) – 140 °C (284 °F)
Revision: 2010 May2011 QX56

TM-126
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0735 5GR INCORRECT RATIO
P0735 5GR INCORRECT RATIO
DescriptionINFOID:0000000006226833
This malfunction is detected when the A/T does not shift
into 5GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or s horted) but by mechanical malfunction such as control
valve sticking, improper solenoid valve operation, etc.
DTC LogicINFOID:0000000006226834
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
“ TM-127, "
Diagnosis Procedure"” must be performed before star ting “DTC CONFIRMATION PROCE-
DURE”.
 Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause secondary malfunction.
 Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK ATF TEMPERATURE
With CONSULT-III
1. Start the engine.
2. Select “ATF TEMP 1” in “Data Monitor” in “TRANSMISSION”.
3. Check ATF temperature is in the following range.
With GST
1. Start the engine.
2. Drive vehicle for approximately 5 minutes in urban areas.
Is ATF temperature within specified range?
YES >> GO TO 3.
NO >> Drive vehicle to warm ATF or stop engine to cool ATF.
3.CHECK SYMPTOM (PART 1)
With CONSULT-III
1. Select “5TH GR FNCTN P0735” in “DTC & SRT confirmation” in “TRANSMISSION”.
2. Drive vehicle with manual mode and maintain the following conditions.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0735 Gear 5 Incorrect Circuit The gear ratio is:
 1.060 or more
 0.940 or less Input clutch solenoid valve
 Direct clutch solenoid valve
 High and low reverse clutch
solenoid valve
 Front brake solenoid valve
 Low brake solenoid valve
 2346 brake solenoid valve
 Anti-interlock solenoid valve
 Each clutch and brake
 Output speed sensor
 Input speed sensor 1, 2
 Hydraulic co ntrol circuit
ATF TEMP 1 : 20 °C (68 °F) – 140 °C (284 °F)
Revision: 2010 May2011 QX56

TM-140
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P1730 INTERLOCK
P1730 INTERLOCK
DescriptionINFOID:0000000006226857
Fail-safe function to detect interlock conditions.
DTC LogicINFOID:0000000006226858
DTC DETECTION LOGIC
NOTE:
When the vehicle is driven fixed
in 2GR, an input speed sensor malfunction is displayed, but this is
not an input speed sensor malfunction.
DTC CONFIRMATION PROCEDURE
CAUTION:
“TM-141, "
Diagnosis Procedure"” must be performed before star ting “DTC CONFIRMATION PROCE-
DURE”.
 Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause
secondary malfunction.
 Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Start the engine.
2. Select “SLCT LVR POSI” and “GEAR” in “Data Monitor” in “TRANSMISSION”.
3. Drive vehicle the following condition.
4. Perform “Self Diagnostic Results” in “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is
“P1730” detected?
YES >> Go to TM-141, "Diagnosis Procedure".
NO >> INSPECTION END
Judgment of InterlockINFOID:0000000006226859
Refer to TM-74, "Fail-Safe".
DTC Trouble diagnosis name DTC is detected if... Possible cause
P1730 Interlock The output speed sensor de-
tects the deceleration of 12 km/
h (7 MPH) or more for 1 sec-
ond. Harness or connectors
(Solenoid valve circuit is open
or shorted.)
 Input clutch solenoid valve
 Direct clutch solenoid valve
 High and low reverse clutch solenoid valve
 Front brake solenoid valve
 Low brake solenoid valve
 2346 brake solenoid valve
 Anti-interlock solenoid valve
 Each clutch
 Hydraulic co ntrol circuit
SLCT LVR POSI : D
GEAR : 1st through 7th
Revision: 2010 May2011 QX56