BATTERY INFINITI QX56 2011 Factory Service Manual

EC-84
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
54
(G/R) 175
(B) Intake valve timing control sole-
noid valve (bank 2)
Output[Engine is running]
 Warm-up condition
 Idle speed
BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000rpm 7 - 12 V
57
(W) 175
(B) Throttle control motor (Open) Output [Ignition switch: ON]
 Engine: Stopped
 Selector lever: D
 Accelerator pedal: Fully depressed
0 - 14 V
[Ignition switch: ON]
 Engine: Stopped
 Selector lever: D position
 Accelerator pedal: Fully released 0 - 14 V
60
(B) — Shield — — —
63
(R) 175
(B) Throttle control motor (Close) Output [Ignition switch: ON]
 Engine: Stopped
 Selector lever: D position
 Accelerator pedal: In the middle of
releasing operation 0 - 14 V
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
JMBIA0038GB
JMBIA0031GB
JMBIA0032GB
JMBIA0031GB
Revision: 2010 May2011 QX56

ECM
EC-85
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
64
(V/W) 175
(B) EVAP canister purge volume
control solenoid valve
Output[Engine is running]
 Idle speed
 Accelerator pedal: Not depressed
even slightly, after engine starting BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Engine speed: About 2,000 rpm (More than 100 seconds after start-
ing engine) BATTERY VOLTAGE
(11 - 14 V)
67
(V) 175
(B) Manifold absolute pressure sen-
sor
Input[Engine is running]
 Warm-up condition
 Idle speed
1.2 V
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm 1.5 V
68
(BR/
W) —
Sensor ground
[Camshaft position sensor (bank
1)] —— —
70
(W/L) —Sensor ground
(Manifold absolute pressure
sensor)
—— —
73
(P) 99
(LG/ B) Camshaft position sensor (bank
2)
Input[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle 3.0 - 5.0 V
[Engine is running]
 Engine speed: 2,000 rpm 3.0 - 5.0 V
74
(L) 175
(B) A/F sensor 1 (bank 2) Input [Ignition switch: ON] 2.5 V
76
(W/
G) 98
(G/
W) Sensor power supply
(Crankshaft position sensor)
— [Ignition switch: ON] 5 V
77
(Y/R) 68
(BR/ W) Sensor power supply
[Camshaft position sensor (bank
1)]
— [Ignition switch: ON] 5 V
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
OutputJMBIA0039GB
JMBIA0040GB
JMBIA0045GB
JMBIA0046GB
Revision: 2010 May2011 QX56

EC-88
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
101
(R)
102 (R) 175
(B) Fuel injector No. 1 (HI)
Fuel injector No. 6 (HI)
Input[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
103 (G)
104 (G) 175
(B) Fuel injector No. 7 (LO)
Fuel injector No. 4 (LO)
Output[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
105
(L/W) 175
(B) High pressure fuel pump (HI) Input [Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
OutputJPBIA3345ZZ
JPBIA3347ZZ
JPBIA3355ZZ
JPBIA3356ZZ
JPBIA3340ZZ
JPBIA3341ZZ
Revision: 2010 May2011 QX56

ECM
EC-89
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
106
(R)
107 (R) 175
(B) Fuel injector No. 7 (HI)
Fuel injector No. 4 (HI)
Output[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
108 (G)
109 (G) 175
(B) Fuel injector No. 1 (LO)
Fuel injector No. 6 (LO)
Output[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
11 0
(L/B) 175
(B) High pressure fuel pump (LO) Input [Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
OutputJPBIA3345ZZ
JPBIA3347ZZ
JPBIA3355ZZ
JPBIA3356ZZ
JPBIA3342ZZ
JPBIA3343ZZ
Revision: 2010 May2011 QX56

EC-90
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
111
(R) 175
(B) Fuel injector driver power supply Input [Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14 V)
11 2
(SB) 175
(B) Fuel injector driver power supply Input [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
11 4 (B) — ECM ground — — —
11 5 (B) — ECM ground — — —
120 (Y) 175
(B) EVAP canister vent control valve Output [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
122
(BR/ W) 175
(B) VVEL actuator motor relay abort
signal (VVEL control module)
Input [Ignition switch: ON] 0 V
123
(V/R) 175
(B) Throttle control mo
tor relay Output [Ignition switch: ON
→ OFF] 0 - 1.0 V
↓
BATTERY VOLTAGE
(11 - 14 V)
↓
0 V
[Ignition switch: ON] 0 - 1.0 V
125
(GR) 175
(B) Fuel pump control module
(FPCM)
Output[When cranking engine] 0 - 0.5 V
[Engine is running]
 Warm-up condition
0 - 4.0 V
126 (O) 129
(P/L) Accelerator pedal position sen-
sor 2
Input[Ignition switch: ON]
 Engine: Stopped
 Accelerator pedal: Fully released
0.28 - 0.48 V
[Ignition switch: ON]
 Engine: Stopped
 Accelerator pedal: Fully depressed 2.0 - 2.5 V
128 (Y) 130
(R) ASCD steering switch Input [Ignition switch: ON]
 ASCD steering switch: OFF
4 V
[Ignition switch: ON]
 MAIN switch: Pressed 0 V
[Ignition switch: ON]
 CANCEL switch: Pressed 1 V
[Ignition switch: ON]
 RESUME/ACCELERATE switch: Pressed 3 V
[Ignition switch: ON]
 SET/COAST switch: Pressed 2 V
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
JPBIA3344ZZ
Revision: 2010 May2011 QX56

ECM
EC-91
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
128
(Y) 175
(B) ICC steering switch Input [Ignition switch: ON]
 ICC steering switch: OFF
4.2 V
[Ignition switch: ON]
 MAIN switch: Pressed 0 V
[Ignition switch: ON]
 CANCEL switch: Pressed 1.9 V
[Ignition switch: ON]
 RESUME/ACCELERATE switch: Pressed 3.7 V
[Ignition switch: ON]
 SET/COAST switch: Pressed 3.2 V
[Ignition switch: ON]
 DISTANCE switch: Pressed 2.6 V
[Ignition switch: ON]
 DYNAMIC DRIVER ASSISTANCE switch: Pressed 1.0 V
129
(P/L) —Sensor ground
(Accelerator pedal position sen-
sor 2)
—— —
130 (R) —Sensor ground
(ASCD steering switch/ICC
steering switch) —— —
131
(L/W) 129
(P/L) Sensor power supply
(Accelerator pedal position sen-
sor 2)
— [Ignition switch: ON] 5 V
133
(SB) 150
(R) Sensor power supply
(Refrigerant pressure sensor/
Battery current sensor/EVAP
control system pressure sensor)
— [Ignition switch: ON] 5 V
134
(V/W) 175
(B) Fuel temperature sensor Input
[Engine is running]
 Warm-up condition2.8 V
136 (W/
R) 140
(R/Y) Accelerator pedal position sen-
sor 1
Input[Ignition switch: ON]
 Engine: Stopped
 Accelerator pedal: Fully released
0.65 - 0.87 V
[Ignition switch: ON]
 Engine: Stopped
 Accelerator pedal: Fully depressed 4.3 - 4.8 V
137 (W/
G) 140
(R/Y) Sensor power supply
(Accelerator pedal position sen-
sor 1)
— [Ignition switch: ON] 5 V
138 (V) 150
(R) Battery current sensor Input [Engine is running]
 Battery: Fully charged*
2
 Idle speed2.6 - 3.5 V
139 (G) 175
(B) Battery temperature sensor Input [Engine is running]
 Battery temperature: 25
°C
 Idle speed 3.3 V
140
(R/Y) —Sensor ground
(Accelerator pedal position sen-
sor 1) —— —
141
(SB) 175
(B) Ignition switch Input [Ignition switch: OFF] 0 V
[Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14 V)
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
Revision: 2010 May2011 QX56

EC-92
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
142
(R/W) 175
(B) Fuel pump control module
(FPCM) check
Input[When cranking engine] 0 V
[Engine is running]
 Warm-up condition
 Idle speed
9 V
143
(L/Y) 150
(R) EVAP control system pressure
sensor
Input [Ignition switch: ON] 1.8 - 4.8 V
144
(O/B) 150
(R) Refrigerant pressure sensor Input [Engine is running]
 Warm-up condition
 Both A/C switch and blower fan mo-
tor switch: ON (Compressor oper-
ates) 1.0 - 4.0 V
146 (L) — CAN communication line — — —
147
(G/Y) 175
(B) ASCD/ICC brake switch Input [Ignition switch: ON]
 Brake pedal: Slightly depressed
0 V
[Ignition switch: ON]
 Brake pedal: Fully released BATTERY VOLTAGE
(11 - 14 V)
150 (R) —Sensor ground
(Refrigerant pressure sensor/
Battery current sensor/EVAP
control system pressure sensor) —— —
151 (P) — CAN communication line — — —
156 (L) 175
(B) Power supply
for ECM (Back-
up) Input [Ignition switch: OFF] BATTERY VOLTAGE
(11 - 14 V)
158
(W/B) 175
(B) Stop lamp switch Input [Ignition switch: OFF]
 Brake pedal: Fully released
0 V
[Ignition switch: OFF]
 Brake pedal: Slightly depressed BATTERY VOLTAGE
(11 - 14 V)
161 (R/W) — ENG communication line — — —
163
(L/G) 175
(B) ECM relay (Self shut-off) Output [Engine is running]
[Ignition switch: OFF]
 A few seconds after turning ignition
switch OFF 0 - 1.5 V
[Ignition switch: OFF]
 More than a few seconds after turn- ing ignition switch OFF BATTERY VOLTAGE
(11 - 14 V)
165
(GR/ R) —
NOTE:
Not used —— —
166 (W) — ENG communication line — — —
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
Revision: 2010 May2011 QX56

ECM
EC-93
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
*1: This may vary depending on internal resistance of the tester.
*2: Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to PG-159, "
How to Handle Battery".
Fail-safeINFOID:0000000006217731
NON DTC RELATED ITEM
DTC RELATED ITEM
169
(G/B) 175
(B) Engine speed signal output Input [Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle 0 - 7.0 V
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm 0 - 7.0 V
171 (W) 175
(B) Power supply for ECM Input [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
172 (W) 175
(B) Power supply for ECM Input [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
173 (O) 175
(B) Throttle contro
l motor power
supply Input [Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14 V)
174 (B) — ECM ground — — —
175 (B) — ECM ground — — —
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
OutputJPBIA3352ZZ
JPBIA3354ZZ
Detected items Engine operating condition
in fail-safe mode RemarksReference
page
Malfunction indicator
circuit Engine speed will not rise
more than 2,500 rpm due
to the fuel cut When there is an open circuit on MIL circuit, the ECM cannot warn
the driver by illuminating MIL when there is malfunction on engine
control system.
Therefore, when electrical controlled throttle and part of ECM related
diagnoses are continuously detected as NG for 5 trips, ECM warns
the driver that engine control system malfunctions and MIL circuit is
open by means of operating the fail-safe function.
The fail-safe function also operates when above diagnoses except
MIL circuit are detected and demands the driver to repair the malfunc-
tion. EC-515
Revision: 2010 May2011 QX56

ECM
EC-97
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
Priority Detected items (DTC)
1  U0101 CAN communication line  U0113 U1003 CAN communication line
 U1001 CAN communication line
 U1024 VVEL CAN communication line
 P006A P0101 P0102 P0103 Mass air flow sensor
 P010A Manifold absolute pressure sensor
 P0112 P0113 P0127 Intake air temperature sensor
 P0116 P0117 P0118 P0125 Engine coolant temperature sensor
 P0122 P0123 P0222 P0223 P1225 P1226 P2135 Throttle position sensor
 P0128 Thermostat function
 P0181 P0182 P0183 Fuel tank temperature sensor
 P0196 P0197 P0198 Engine oil temperature sensor
 P0327 P0328 P0332 P0333 Knock sensor
 P0335 Crankshaft position sensor
 P0340 P0345 Camshaft position sensor
 P0460 P0461 P0462 P0463 Fuel level sensor
 P0500 Vehicle speed sensor
 P0527 Cooling fan speed sensor
 P0605 P0607 P0611 P062B ECM
 P0643 Sensor power supply
 P0700 TCM
 P0705 P0850 Transmission range switch
 P1089 P1092 P1608 VVEL control shaft position sensor
 P1197 Out of gas*
 P1220 Fuel pump control module (FPCM)
 P1421 P1423 P1424 Cold start control
 P1550 P1551 P1552 P1553 P1554 Battery current sensor
 P1556 P1557 Battery temperature sensor
 P1606 P1607 VVEL control module
 P1610 - P1615 NATS
 P2122 P2123 P2127 P2128 P2138 Accelerator pedal position sensor
 P2539 P2541 P2542 Low fuel pressure sensor
Revision: 2010 May2011 QX56

EC-110
< ECU DIAGNOSIS INFORMATION >[VK56VD]
VVEL CONTROL MODULE
VVEL CONTROL MODULE
Reference ValueINFOID:0000000006217735
TERMINAL LAYOUT
PHYSICAL VALUES
NOTE:
 VVEL control module is located under the battery. Temporarily remove the battery to check voltage of the
terminals.
 Specification data are reference values and are measured between each terminals.
 Pulse signal is measured by CONSULT-III.
JMBIA0857ZZ
Terminal No. Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
1
(R) 14
(B) VVEL actuator motor power
supply (bank 2)
Input [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14V)
2
(L/W) 14
(B) VVEL actuator motor
(High lift) (bank 2)
Output[Engine is running]
 Warm-up condition
 Idle speed
0 - 14 V
[Engine is running]
 Warm-up condition
 When revving engine up to 2,000 rpm quickly 0 - 14 V
3
(W) 6
(R) VVEL control shaft position
sensor 1 (bank 1)
Input[Engine is running]
 Warm-up condition
 Idle speed
0.25 - 1.40 V
[Engine is running]
 Warm-up condition
 When revving engine up to 3,000 rpm quickly 0.25 - 4.75 V
4
(L/W) —Sensor ground
[VVEL control shaft position
sensor 1 (bank 2)] —— —
JMBIA0854ZZ
JMBIA0855ZZ
Revision: 2010 May2011 QX56