ECU INFINITI QX56 2011 Factory Service Manual

DIAGNOSIS SYSTEM (ECM)EC-61
< SYSTEM DESCRIPTION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
 ECM blinks MIL for about 10 seconds if all SRT codes are not set.
MALFUNCTION WARNING MODE
Description
In this function ECM turns on or blinks MIL when it det
ects a malfunction in the emission control system com-
ponents and/or the powertrain control components (which affe ct vehicle emissions) to inform the driver that a
malfunction has been detected.
Operation Procedure
1. Turn ignition switch ON.
2. Check that MIL illuminates. If it remains OFF, check MIL circuit. Refer to EC-515, "
Diagnosis Procedure".
3. Start engine and let it idle.  For two trip detection logic diagnoses, ECM turns on MIL when it detects the same malfunction twice in
the two consecutive driving cycles.
 For 1st trip detection logic diagnoses, ECM turns on MIL when it detects a malfunction in one driving cycle.
 ECM blinks MIL when it detects a malfunction t hat may damage the three way catalyst (misfire).
SELF-DIAGNOSTIC RESULTS MODE
Description
This function allows to indicate DTCs or 1st trip DTCs stored in ECM according to the number of times MIL is
blinking.
How to Set Self-diagnostic Results Mode
NOTE:
 It is better to count the time accurately with a clock.
 It is impossible to switch the diagnostic mode when an accelerator pedal position sensor circuit has a mal-
function.
 After ignition switch is turned off, ECM is a lways released from the “Self-diagnostic results” mode.
1. Confirm that accelerator pedal is fully releas ed, turn ignition switch ON and wait 3 seconds.
2. Repeat the following procedure quickly five times within 5 seconds.  Fully depress the accelerator pedal.
 Fully release the accelerator pedal.
3. Wait 7 seconds, fully depress the accelerator pedal and keep it depressed for approx. 10 seconds until the
MIL starts blinking.
NOTE:
Do not release the accelerator pedal for 10 seconds if MIL starts blinking during this period. This blinking
is displaying SRT status and is continued for another 10 seconds.
4. Fully release the accelerator pedal. ECM has entered to Self-diagnostic results mode.
JMBIA1515GB
Revision: 2010 May2011 QX56

DIAGNOSIS SYSTEM (ECM)EC-63
< SYSTEM DESCRIPTION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
In this way, all the detected malfunctions are classi
fied by their DTC numbers. The DTC 0000 refers to no mal-
function. Refer to EC-98, "
DTC Index".
How to Erase Self-diagnostic Results
By performing this procedure, ECM memory is erased and the following diagnostic information is erased as
well.
 Diagnostic trouble codes
 1st trip diagnostic trouble codes
 Freeze frame data
 1st trip freeze frame data
 System readiness test (SRT) codes
 Test values
NOTE:
Also, if a battery terminal is disconnected, ECM memory is erased and the diagnostic information as listed
above is erased. (The amount of time required for eras ing may vary from a few seconds to several hours.)
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
5. Set ECM in Self-diagnostic results.
6. The diagnostic information has been erased from the backup memory in the ECM. Fully depress the accelerator pedal and keep it depressed for more than 10 seconds.
7. Fully release the accelerator pedal, and confirm the DTC 0000 is displayed.
CONSULT-III FunctionINFOID:0000000006217729
FUNCTION
*: The following emission-related diagnostic information is cleared when the ECM memory is erased.
 Diagnostic trouble codes
 1st trip diagnostic trouble codes
 Freeze frame data
 1st trip freeze frame data
 System readiness test (SRT) codes
Test values
WORK SUPPORT MODE
Work Item
Diagnostic test mode Function
Work support This mode enables a technician to adjust some devices faster and more accurately by following the in-
dications on the CONSULT-III unit.
Self diagnostic result Self-diagnostic results such as 1st trip DTC, DTCs and 1st trip freeze frame data or freeze frame data
can be read and erased quickly.*
Data monitor Input/Output data in the ECM can be read.
Active test Diagnostic Test Mode in which CONSULT-III drives some actuators apart from the ECMs and also shifts
some parameters in
a specified range.
DTC & SRT confirmation The status of system monitoring tests and the self-diagnosis status/results can be confirmed.
Function test This mode is used to inform customers when the vehicle requires periodic maintenance.
ECU identification ECM part number can be read.
Revision: 2010 May2011 QX56

EC-64
< SYSTEM DESCRIPTION >[VK56VD]
DIAGNOSIS SYSTEM (ECM)
*: This function is not necessary
in the usual service procedure.
SELF-DIAG RESULTS MODE
Self Diagnostic Item
Regarding items of DTC and 1st trip DTC, refer to EC-98, "DTC Index".
How to Read DTC and 1st Trip DTC
DTCs and 1st trip DTCs related to the malfunction are displayed in “Self-diag results”.
 When ECM detects a 1st trip DTC, “1t” is displayed for “TIME”.
 When ECM has detected a current DTC, “0” is displayed for “TIME”.
 If “TIME” is neither “0” nor “1t”, the DTC occurred in the past and ECM shows the number of times the vehi-
cle has been driven since the last detection of the DTC.
How to Erase DTC and 1st Trip DTC
NOTE:
 If the ignition switch stays ON after repair work, be su re to turn ignition switch OFF once. Wait at least 10
seconds and then turn it ON (engine stopped) again.
 If the DTC is not for A/T related items (see EC-98, "
DTC Index"), skip step 1.
1. Erase DTC in TCM. Refer to TM-60, "
Diagnosis Description".
2. Select “ENGINE” with CONSULT-III.
3. Select “SELF-DIAG RESULTS”.
4. Touch “ERASE”. (DTC in ECM will be erased.)
WORK ITEM CONDITION USAGE
IDLE AIR VOL LEARN  THE IDLE AIR VOLUME THAT KEEPS THE ENGINE
WITHIN THE SPECIFIED RANGE IS MEMORIZED IN
ECM. When learning the idle air volume
EVAP SYSTEM CLOSE CLOSE THE EVAP CANISTER VENT CONTROL VALVE IN
ORDER TO MAKE EVAP SYSTEM CLOSE UNDER THE
FOLLOWING CONDITIONS.
 IGN SW ON
 ENGINE NOT RUNNING
 AMBIENT TEMPERATURE IS ABOVE 0
°C (32 °F).
 NO VACUUM AND NO HIGH PRESSURE IN EVAP SYS-
TEM
 FUEL TANK TEMP. IS MORE THAN 0 °C (32 °F).
 WITHIN 10 MINUTES AFTER STARTING “EVAP SYS-
TEM CLOSE”
 WHEN TRYING TO EXECUTE “EVAP SYSTEM CLOSE” UNDER THE CONDITION EXCEPT ABOVE, CONSULT-
III WILL DISCONTINUE IT AND DISPLAY APPROPRI-
ATE INSTRUCTION.
NOTE:
WHEN STARTING ENGINE, CONSULT-III MAY DIS-
PLAY “BATTERY VOLTAGE IS LOW. CHARGE BAT-
TERY”, EVEN WHEN USING A CHARGED BATTERY. When detecting EVAP vapor leak
in the EVAP system
FUEL PRESSURE RELEASE  FUEL PUMP WILL STOP BY TOUCHING “START” DUR-
ING IDLING.
CRANK A FEW TIMES AFTER ENGINE STALLS. When releasing fuel pressure from
fuel line
SELF-LEARNING CONT  THE COEFFICIENT OF SELF-LEARNING CONTROL
MIXTURE RATIO RETURNS TO THE ORIGINAL COEF-
FICIENT. When clearing mixture ratio self-
learning value
TARGET IDLE RPM ADJ*  IDLE CONDITION When setting target idle speed
VIN REGISTRATION  IN THIS MODE, VIN IS REGISTERED IN ECM. When registering VIN in ECM
TARGET IGN TIM ADJ*  IDLE CONDITION When adjusting target ignition tim-
ing
CLSD THL POS LEARN  IGNITION ON AND ENGINE STOPPED. When learning the throttle valve
closed position
VVEL POS SEN ADJ PREP  USE THIS ITEM ONLY WHEN REPLACING VVEL ACTU-
ATOR SUB ASSEMBLY.
 IGNITION ON AND ENGINE STOPPED. When adjusting VVEL control
shaft position sensor
Revision: 2010 May2011 QX56

EC-72
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
ECU DIAGNOSIS INFORMATION
ECM
Reference ValueINFOID:0000000006217730
VALUES ON THE DIAGNOSIS TOOL
NOTE:
 Specification data are reference values.
 Specification data are output/input values which are
detected or supplied by the ECM at the connector.
* Specification data may not be directly relat ed to their components signals/values/operations.
i.e. Adjust ignition timing with a timing light before monitoring IGN TIMING, because the monitor may show
the specification data in spite of the ignition timing not being adjusted to the specification data. This IGN TIM-
ING monitors the data calculated by the ECM accordi ng to the signals input from the camshaft position sen-
sor and other ignition timing related sensors.
CONSULT-III MONITOR ITEM
Monitor Item Condition Values/Status
ENG SPEED  Run engine and compare CONSULT-III value with the tachometer indication. Almost the same speed as
the tachometer indication
MAS A/F SE-B1 See EC-161, "
Description".
B/FUEL SCHDL See EC-161, "
Description".
A/F ALPHA-B1 See EC-161, "
Description".
A/F ALPHA-B2 See EC-161, "
Description".
COOLAN TEMP/S  Ignition switch: ON Indicates engine coolant
temperature
A/F SEN1 (B1)  Engine: After warming up Maintaining engine speed at 2,000 rpm Fluctuates around 1.5 V
A/F SEN1 (B2)  Engine: After warming up Maintaining engine speed at 2,000 rpm Fluctuates around 1.5 V
HO2S2 (B1)  Revving engine from idle up to 3,000 rpm quickly after the following condi-
tions are met.
- Engine: After warming up
- After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load 0 - 0.3 V
⇔ Approx. 0.6 - 1.0
V
HO2S2 (B2)  Revving engine from idle up to 3,000 rpm quickly after the following condi-
tions are met.
- Engine: After warming up
- After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load 0 - 0.3 V
⇔ Approx. 0.6 - 1.0
V
HO2S2 MNTR (B1)  Revving engine from idle up to 3,000 rpm quickly after the following condi-
tions are met.
- Engine: After warming up
- After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and
at idle for 1 minute under no load LEAN
⇔ RICH
HO2S2 MNTR (B2)  Revving engine from idle up to 3,000 rpm quickly after the following condi-
tions are met.
- Engine: After warming up
- After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load LEAN
⇔ RICH
VHCL SPEED SE  Turn drive wheels and compare CONSULT-III value with the speedometer in-
dication. Almost the same speed as
speedometer indication
BATTERY VOLT  Ignition switch: ON (Engine stopped) 11 - 14 V
ACCEL SEN 1  Ignition switch: ON
(Engine stopped) Accelerator pedal: Fully released 0.65 - 0.87 V
Accelerator pedal: Fully depressed 4.3 - 4.8 V
ACCEL SEN 2*
1 Ignition switch: ON (Engine stopped) Accelerator pedal: Fully released 0.56 - 0.96 V
Accelerator pedal: Fully depressed 4.0 - 4.8 V
Revision: 2010 May2011 QX56

ECM
EC-73
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
TP SEN 1-B1
 Ignition switch: ON
(Engine stopped)
 Selector lever: D position Accelerator pedal: Fully released More than 0.36 V
Accelerator pedal: Fully depressed Less than 4.75 V
TP SEN 2-B1*
1 Ignition switch: ON (Engine stopped)
 Selector lever: D position Accelerator pedal: Fully released More than 0.36 V
Accelerator pedal: Fully depressed Less than 4.75 V
FUEL T/TMP SE  Ignition switch: ON Indicates fuel tank tempera-
ture
EVAP SYS PRES  Ignition switch: ON Approx. 1.8 - 4.8 V
FUEL LEVEL SE  Ignition switch: ON Depending on fuel level of
fuel tank
START SIGNAL  Ignition switch: ON → START → ON OFF → ON → OFF
CLSD THL POS  Ignition switch: ON
(Engine stopped) Accelerator pedal: Fully released ON
Accelerator pedal: Slightly depressed OFF
AIR COND SIG  Engine: After warming up, idle
the engine Air conditioner switch: OFF OFF
Air conditioner switch: ON
(Compressor operates.)
ON
PW/ST SIGNAL  Engine: After warming up, idle
the engine Steering wheel: Not being turned OFF
Steering wheel: Being turned ON
LOAD SIGNAL  Ignition switch: ON Rear window defogger switch: ON
and/or
Lighting switch: 2nd position
ON
Rear window defogger switch and lighting
switch: OFF OFF
IGNITION SW  Ignition switch: ON → OFF → ON ON → OFF → ON
HEATER FAN SW  Engine: After warming up, idle
the engine Heater fan switch: ON ON
Heater fan switch: OFF OFF
BRAKE SW  Ignition switch: ON Brake pedal: Fully released OFF
Brake pedal: Slightly depressed ON
IGN TIMING  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle 1 - 4
°BTDC
2,000 rpm 25 - 45 °BTDC
COMBUSTION — These items are displayed
but are not applicable to this
model.
CAL/LD VALUE  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle 5 - 35%
2,500 rpm 5 - 35%
MASS AIRFLOW  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle 2.0 - 6.0 g/s
2,500 rpm 7.0 - 20.0 g/s
PURG VOL C/V  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
(Accelerator pedal: Not depressed even
slightly, after engine starting.)
0%
2,000 rpm 5%
INT/V SOL (B1)  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle 0 - 2%
2,000 rpm Approx. 0 - 50%
Monitor Item Condition Values/Status
Revision: 2010 May2011 QX56

EC-74
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
INT/V SOL (B2) Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle 0 - 2%
2,000 rpm Approx. 0 - 50%
AIR COND RLY  Engine: After warming up, idle
the engine A/C switch: OFF OFF
A/C switch: ON
(Compressor operates)
ON
VENT CONT/V  Ignition switch: ON OFF
THRTL RELAY  Ignition switch: ON ON
A/F S1 HTR (B1)  Engine: After warming up, idle the engine
(More than 140 seconds after starting engine) 4 - 100%
A/F S1 HTR (B2)  Engine: After warming up, idle the engine
(More than 140 seconds after starting engine) 4 - 100%
HO2S2 HTR (B1)  Engine speed: Below 3,600 rpm after the following conditions are met.
- Engine: After warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load ON
 Engine speed: Above 3,600 rpm OFF
HO2S2 HTR (B2)  Engine speed: Below 3,600 rpm after the following conditions are met.
- Engine: After warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load ON
 Engine speed: Above 3,600 rpm OFF
ALT DUTY SIG  Power generation voltage variable control: Operating ON
 Power generation voltage variable control: Not operating OFF
I/P PULLY SPD  Vehicle speed: More than 20 km/h (12 MPH) Almost the same speed as
the tachometer indication
VEHICLE SPEED  Turn drive wheels and compare CONSULT-III value with the speedometer in-
dication. Almost the same speed as
the speedometer indication
IDL A/V LEARN  Engine: Running Idle air volume learning has not been per-
formed yet.
YET
Idle air volume learning has already been
performed successfully. CMPLT
TRVL AFTER MIL  Ignition switch: ON Vehicle has traveled after MIL has illumi-
nated.0 - 65,535 km
(0 - 40,7
23 miles)
SNOW MODE SW  Ignition switch: ON Snow mode switch: ON ON
Snow mode switch: OFF OFF
ENG OIL TEMP  Engine: After warming up More than 70 °C (158 °F)
MAIN SW  Ignition switch: ON MAIN switch: Pressed ON
MAIN switch: Released OFF
CANCEL SW  Ignition switch: ON CANCEL switch: Pressed ON
CANCEL switch: Released OFF
RESUME/ACC SW  Ignition switch: ON RESUME/ACCELERATE switch:
Pressed
ON
RESUME/ACCELERATE switch: Re-
leased OFF
SET SW  Ignition switch: ON SET/COAST switch: Pressed ON
SET/COAST switch: Released OFF
BRAKE SW1
(ASCD/ICC brake
switch)  Ignition switch: ON
Brake pedal: Fully released ON
Brake pedal: Slightly depressed OFF
Monitor Item Condition Values/Status
Revision: 2010 May2011 QX56

ECM
EC-75
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
BRAKE SW2
(Stop lamp switch)
 Ignition switch: ON Brake pedal: Fully released OFF
Brake pedal: Slightly depressed ON
DIST SW  Ignition switch: ON DISTANCE switch: Pressed ON
DISTANCE switch: Released OFF
CRUISE LAMP  Ignition switch: ON MAIN switch: Pressed at the 1st time
→
at the 2nd time ON
→ OFF
AC EVA TEMP  Engine: Running Indicates A/C evaporator
temperature sent from“uni-
fied meter and A/C amp.”.
AC EVA TARGET  Engine: Running Indicates target A/C evapo-
rator temperature sentfrom
“unified meter and A/C
amp.”.
FAN DUTY  Engine: Running 0 - 100%
ALT DUTY  Engine: Idle 0 - 80%
BAT CUR SEN  Engine speed: Idle
 Battery: Fully charged*
2
 Selector lever: P or N position
 A/C switch: OFF
No load Approx. 2,600 - 3,500 mV
A/F ADJ-B1  Engine: Running −0.330 - 0.330
A/F ADJ-B2  Engine: Running −0.330 - 0.330
P/N POSI SW  Ignition switch: ON Selector lever: P or N ON
Selector lever: Except above position OFF
INT/A TEMP SE  Ignition switch: ON Indicates intake air temper-
ature
AC PRESS SEN  Engine: Idle
 Both A/C switch and blower fan switch: ON (Compressor operates) 1.0 - 4.0 V
FUEL PRES SEN  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 2.74 Mpa
2,000 rpm Approx. 3.0 Mpa
FUEL INJ B1  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 1.4 msec
2,000 rpm Approx. 1.0 msec
FUEL INJ B2  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 1.4 msec
2,000 rpm Approx. 1.0 msec
INT/V TIM (B1)  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
−5 - 5 °CA
2,000 rpm Approx. 0 - 30 °CA
INT/V TIM (B2)  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
−5 - 5 °CA
2,000 rpm Approx. 0 - 30 °CA
MAP SENSOR  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 1.0 V
2,000 rpm Approx. 1.35 V
EVAP LEAK DIAG  Ignition switch: ON Indicates the condition of
EVAP leak diagnosis.
Monitor Item Condition Values/Status
Revision: 2010 May2011 QX56

EC-76
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
EVAP DIAG READY  Ignition switch: ON Indicates the ready condi-
tion of EVAP leak diagnosis.
VVEL LEARN  Ignition switch: OFF
→ ON
(After warming up) VVEL learning has no
t been performed
yet. YET
VVEL learning has already been per-
formed successfully. DONE
VVEL SEN LEARN-B1  VVEL learning has already been performed successfully Approx. 0.30 - 0.80 V
VVEL SEN LEARN-B2  VVEL learning has already been performed successfully Approx. 0.30 - 0.80 V
VVEL POSITION SEN-
B1  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 0.25 - 1.50 V
When revving engine up to 2,000 rpm
quickly
Approx. 0.25 - 4.75 V
VVEL POSITION SEN-
B2  Engine: After warming up
 Selector lever: P or N position
 Air conditioner switch: OFF
No load Idle Approx. 0.25 - 1.50 V
When revving engine up to 2,000 rpm
quickly
Approx. 0.25 - 4.75 V
VVEL TIM-B1  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 0 - 23 deg
When revving engine up to 2,000 rpm
quickly
Approx. 0 - 90 deg
VVEL TIM-B2  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 0 - 23 deg
When revving engine up to 2,000 rpm
quickly
Approx. 0 - 90 deg
FPCM  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load  Engine: Cranking HI
 Revving engine from idle to 4,000 rpm
quickly MID
 Engine: Idle
 Engine coolant temperature: More than 10 °C (50 °F) LOW
BAT TEMP SEN  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
Indicates the temperature
around the battery.
COOLING FAN SPD  Engine speed: Idle
 Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Water temp: Less than 98
°C Approx. 100 – 200 rpm
Water temp: More than 98 °C Approx. 600 – 700 rpm
THRTL STK CNT B1 NOTE:
The item is indicated, but not used. —
HO2 S2 DIAG2(B1) NOTE:
The item is indicated, but not used.
—
HO2 S2 DIAG2(B2) NOTE:
The item is indicated, but not used. —
FUEL INJ TIMG Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 16 deg
2,000 rpm Approx.
−170 deg
H/P FUEL PUMP DEG  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 211.0 deg
2,000 rpm Approx. 206.0 deg
Monitor Item Condition Values/Status
Revision: 2010 May2011 QX56

ECM
EC-77
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
*1: Accelerator pedal position sensor 2 signal and throttle position sensor 2 signal are converted by ECM internally. Thus, the
y differ
from ECM terminals voltage signal.
*2: Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to PG-159, "
How to Handle Battery".
TERMINAL LAYOUT
PHYSICAL VALUES
NOTE:
 Specification data are reference values and are measured between each terminals.
 Pulse signal is measured by CONSULT-III.
FUEL PRES SEN V Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 1150 mV
2,000 rpm Approx. 1200 mV
L/FUEL PRES SEN  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 0.45 MPa
2,000 rpm Approx. 0.45 MPa
L/FUEL PRES SEN V  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 3250 mV
3,000 rpm Approx. 3100 mV
ECM TEMP 1  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
Indicates the temperature of
ECM internal circuit 1.
ECM TEMP 2  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
Indicates the temperature of
ECM internal circuit 2.
FUEL PUMP DUTY  Engine: After warming up
 Shift lever: P or N
 Air conditioner switch: OFF
No load Engine speed: Idle 30 - 40%
Monitor Item Condition Values/Status
JPBIA3371ZZ
Revision: 2010 May2011 QX56

EC-78
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
1
(R)
2
(R) 175
(B) Fuel injector No. 8 (HI)
Fuel injector No. 5 (HI)
Output[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
3
(G)
4
(G) 175
(B) Fuel injector No. 3 (LO)
Fuel injector No. 2 (LO)
Input[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
5
(B/R) — ECM ground — — —
JPBIA3345ZZ
JPBIA3347ZZ
JPBIA3355ZZ
JPBIA3356ZZ
Revision: 2010 May2011 QX56