ignition INFINITI QX56 2011 Factory Service Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2011, Model line: QX56, Model: INFINITI QX56 2011Pages: 5598, PDF Size: 94.53 MB
Page 783 of 5598
![INFINITI QX56 2011 Factory Service Manual
CCS-48
< ECU DIAGNOSIS INFORMATION >[ICC]
ADAS CONTROL UNIT
Fail-safe
INFOID:0000000006227986
If a malfunction occurs in each system, ADAS contro l unit cancels each control, sounds a beep, and turns](/img/42/57033/w960_57033-782.png "INFINITI QX56 2011 Factory Service Manual
CCS-48
< ECU DIAGNOSIS INFORMATION >[ICC]
ADAS CONTROL UNIT
Fail-safe
INFOID:0000000006227986
If a malfunction occurs in each system, ADAS contro l unit cancels each control, sounds a beep, and turns")
CCS-48
< ECU DIAGNOSIS INFORMATION >[ICC]
ADAS CONTROL UNIT
Fail-safe
INFOID:0000000006227986
If a malfunction occurs in each system, ADAS contro l unit cancels each control, sounds a beep, and turns ON
the warning lamp or indicator lamp.
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
+ − Signal name Input/
Output
1
(V/W)
Ground Warning systems
switch
InputIgnition
switch ON When warning systems
switch is not pressed
12 V
When warning systems
switch is pressed 0 V
3
(R/Y) IBA OFF switch Input Ignition
switch
ON When IBA OFF switch is
not pressed
12 V
When IBA OFF switch is
pressed 0 V
4
(LG/B) Warning systems ON
indicator
OutputIgnition
switch ON Warning systems ON indi-
cator ON
0 V
Warning systems ON indi-
cator OFF 12 V
5
(R) ICC brake hold relay
drive signal
OutputIgnition
switch ON —12 V
At “STOP LAMP” test of
“Active test” 0 V
6
(B) Ground — Ignition
switch ON —0 V
7
(L) ITS communication-H — — — —
8
(Y) ITS communication-L — — — —
12
(G/R) Warning buzzer signal Output Ignition
switch ON Warning buzzer operation 0 V
Warning buzzer not oper-
ating
12 V
14
(L) CAN -H — — — —
15
(P) CAN -L — — — —
16
(W/G) Ignition power supply Input Ignition switch ON Battery Voltage
System Buzzer Warning lamp/Indicator lamp Description
Vehicle-to-vehicle distance control mode High-pitched
toneICC system warn
ing lamp Cancel
Conventional (fixed speed) cruise control mode High-pitched
tone
ICC system warn
ing lamp Cancel
Intelligent Brake Assist (IBA) High-pitched
toneIBA OFF indicator lamp Cancel
Forward Collision Warning (FCW) High-pitched
toneIBA OFF indicator lamp Cancel
Distance Control Assist (DCA) High-pitched
tone
ICC system warn
ing lamp Cancel
Lane Departure Warning (LDW) — Lane departure warning lamp Cancel
Revision: 2010 May2011 QX56
Page 786 of 5598
![INFINITI QX56 2011 Factory Service Manual
CCS
ADAS CONTROL UNITCCS-51
< ECU DIAGNOSIS INFORMATION > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
- CRNT: A malfunction is detected now
- PAST: A malfunction was detected in the past
IGN counter is dis](/img/42/57033/w960_57033-785.png "INFINITI QX56 2011 Factory Service Manual
CCS
ADAS CONTROL UNITCCS-51
< ECU DIAGNOSIS INFORMATION > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
- CRNT: A malfunction is detected now
- PAST: A malfunction was detected in the past
IGN counter is dis")
CCS
ADAS CONTROL UNITCCS-51
< ECU DIAGNOSIS INFORMATION > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
- CRNT: A malfunction is detected now
- PAST: A malfunction was detected in the past
IGN counter is displayed on FFD (Freeze Frame Data).
- 0: The malfunctions that are detected now CAN communication system (U1000, U1010)
- 1 - 39: It increases like 0 → 1 → 2 ··· 38 → 39 after returning to the normal condition whenever the ignition
switch OFF → ON. It returns to 0 when a malfunc tion is detected again in the process.
- If it is over 39, it is fixed to 39 unt il the self-diagnosis results are erased.
Other than CAN communication s ystem (Other than U1000, U1010)
- 1 - 49: It increases like 0 → 1 → 2 ··· 38 → 49 after returning to the normal condition whenever the ignition
switch OFF → ON. It returns to 0 when a malfunc tion is detected again in the process.
- If it is over 49, it is fixed to 49 unt il the self-diagnosis results are erased.
Systems for fail-safe
A: Vehicle-to-vehicle distance control mode
B: Conventional (fixed speed) cruise control mode
C: Intelligent Brake Assist (IBA)
D: Forward Collision Warning (FCW)
E: Distance Control Assist (DCA)
F: Lane Departure Warning (LDW)/Lane Departure Prevention (LDP)
G: Blind Spot Warning (BSW)
DTC
CONSULT-III display Warning lamp Fail-safe
Reference
CONSULT-III On board
display
ICC system warning lamp
IBA OFF indicator lamp
Lane departure warning lamp BSW warning lamp
System
C1A00 0 CONTROL UNIT ON ON ON ON A, B, C, D, E, F, G CCS-83
C1A01 1 POWER SUPPLY CIR ON ON ON ON A, B, C, D, E, F, GCCS-85
C1A02 2 POWER SUPPLY CIR 2 ON ON ON ON A, B, C, D, E, F, GCCS-85
C1A03 3 VHCL SPEED SE CIRC ON ON ON ON A, B, C, D, E, F, GCCS-87
C1A04 4 ABS/TCS/VDC CIRC ON ON ON A, B, C, D, E, FCCS-89
C1A05 5 BRAKE SW/STOP L SW ON ON ON A, B, C, D, E, FCCS-90
C1A06 6 OPERATION SW CIRC ON ON A, B, E, FCCS-94
C1A12 12LASER BEAM OFFCN-
TR ON ON A, C, D, E
CCS-96
C1A13 13 STOP LAMP RLY FIX ON ON A, B, C, D, E CCS-97
C1A14 14 ECM CIRCUIT ON ON A, B, E, FCCS-103
C1A15 15 GEAR POSITION ON ON ON ON A, B, C, D, E, F, GCCS-104
C1A16 16 RADAR STAIN ON ON A, C, D, ECCS-106
C1A17 17 ICC SENSOR MALF ON ON A, B, C, D, ECCS-108
C1A18 18 LASER AIMING INCMP ON ON A, C, D, ECCS-109
C1A21 21ICC SENSOR HIGH
TEMP ON ON A, B, C, D, E
CCS-111
C1A24 24 NP RANGE ON ON ON ON A, B, C, D, E, F, G CCS-113
C1A26 26 ECD MODE MALF ON ON A, B, C, D, ECCS-115
C1A27 27 ECD PWR SUPLY CIR ON ON A, B, C, D, ECCS-116
C1A33 33CAN TRANSMISSION
ERR ON A, B, E
CCS-118
Revision: 2010 May2011 QX56
Page 789 of 5598
![INFINITI QX56 2011 Factory Service Manual
CCS-54
< ECU DIAGNOSIS INFORMATION >[ICC]
ICC SENSOR
ICC SENSOR
Reference ValueINFOID:0000000006224285
VALUES ON THE DIAGNOSIS TOOL
TERMINAL LAYOUT
PHYSICAL VALUES
Monitor item Condition Value/Status](/img/42/57033/w960_57033-788.png "INFINITI QX56 2011 Factory Service Manual
CCS-54
< ECU DIAGNOSIS INFORMATION >[ICC]
ICC SENSOR
ICC SENSOR
Reference ValueINFOID:0000000006224285
VALUES ON THE DIAGNOSIS TOOL
TERMINAL LAYOUT
PHYSICAL VALUES
Monitor item Condition Value/Status")
CCS-54
< ECU DIAGNOSIS INFORMATION >[ICC]
ICC SENSOR
ICC SENSOR
Reference ValueINFOID:0000000006224285
VALUES ON THE DIAGNOSIS TOOL
TERMINAL LAYOUT
PHYSICAL VALUES
Monitor item Condition Value/Status
VHCL SPEED SE While driving Value of vehicle
speed signal
(wheel speed)
YAW RATE While driving Vehicle stopped 0.0
Vehicle turning right Positive value
Vehicle turning left Negative value
PWR SUP MONI Ignition switch ON Power supply
voltage value of ICC sensor
DISTANCE Drive the vehicle and activate
the vehicle-to-vehicle distance
control mode When a vehicle ahead is detected
Displays the dis-
tance from the
preceding vehi- cle
When a vehicle ahead is not detected 0.0
RELATIVE SPD Drive the vehicle and activate
the vehicle-to-vehicle distance
control mode When a vehicle ahead is detected
Displays the rel-
ative speed
When a vehicle ahead is not detected 0.0
LASER OFFSET NOTE:
The item is indicated, but not used
—
LASER HEIGHT NOTE:
The item is indicated, but not used —
STEERING ANGLE Ignition switch ON When setting the steering wheel in straight-ahead posi-
tion
0.0
When turning the steering wheel 90 ° rightward +90
When turning the steering wheel 90 ° leftward -90
STRG ANGLE
SPEED Ignition switch ON At the time of turning the steering wheel Steering wheel
turning speed is
displayed
L/R ADJUST Ignition switch ON At the completion of laser beam adjustment Horizontal cor-
rection value is
displayed
U/D ADJUST Ignition switch ON At the completion of laser beam adjustment Vertical correc-
tion value is dis-
played
JPOIA0105ZZ
Revision: 2010 May2011 QX56
Page 790 of 5598
![INFINITI QX56 2011 Factory Service Manual
CCS
ICC SENSORCCS-55
< ECU DIAGNOSIS INFORMATION > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
Fail-safeINFOID:0000000006224286
If a malfunction occurs in the ICC sensor, ADAS cont rol unit cancels control,](/img/42/57033/w960_57033-789.png "INFINITI QX56 2011 Factory Service Manual
CCS
ICC SENSORCCS-55
< ECU DIAGNOSIS INFORMATION > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
Fail-safeINFOID:0000000006224286
If a malfunction occurs in the ICC sensor, ADAS cont rol unit cancels control,")
CCS
ICC SENSORCCS-55
< ECU DIAGNOSIS INFORMATION > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
Fail-safeINFOID:0000000006224286
If a malfunction occurs in the ICC sensor, ADAS cont rol unit cancels control, sounds a beep, and turns ON the
ICC system warning lamp in the combination meter.
DTC Inspection Priority ChartINFOID:0000000006224287
If multiple DTCs are detected simultaneously, che ck them one by one depending on the following DTC inspec-
tion priority chart.
DTC IndexINFOID:0000000006224288
NOTE:
The details of time display are as per the following.
- 0: The malfunctions that are detected now
CAN communication system (U1000, U1010)
- 1 - 39: It increases like 0 → 1 → 2 ··· 38 → 39 after returning to the normal condition whenever the ignition
switch OFF → ON. It returns to 0 when a malfunc tion is detected again in the process.
- If it is over 39, it is fixed to 39 unt il the self-diagnosis results are erased.
Other than CAN communication s ystem (Other than U1000, U1010)
- 1 - 49: It increases like 0 → 1 → 2 ··· 38 → 49 after returning to the normal condition whenever the ignition
switch OFF → ON. It returns to 0 when a malfunc tion is detected again in the process.
- If it is over 49, it is fixed to 49 unt il the self-diagnosis results are erased.
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
1
(W/G)
GroundIgnition power supply Input Ignition switch ON Battery voltage
3
(L) ITS communication-H — — —
4
(B) Ground — Ignition switch ON 0 V
6
(Y) ITS communication-L — — —
Priority Detected items (DTC)
1 U1000: CAN COMM CIRCUIT
U1010: CONTROL UNIT (CAN)
2 C1A50: ADAS MALFUNCTION
3 C1A01: POWER SUPPLY CIR
C1A02: POWER SUPPLY CIR 2
C1A12: LASER BEAM OFFCNTR
C1A16: RADAR STAIN
C1A18: LASER AIMING INCMP
C1A21: UNIT HIGH TEMP
C1A39: STRG SEN CIR
U0104: ADAS CAN CIR1
U0121: VDC CAN CIR2
U0126: STRG SEN CAN CIR1
U0405: ADAS CAN CIR2
U0415: VDC CAN CIR1
U0428: STRG SEN CAN CIR2
4 C1A00: CONTROL UNIT
Revision: 2010 May2011 QX56
Page 825 of 5598
![INFINITI QX56 2011 Factory Service Manual
CCS-90
< DTC/CIRCUIT DIAGNOSIS >[ICC]
C1A05 BRAKE SW/STOP LAMP SW
C1A05 BRAKE SW/STOP LAMP SW
DTC LogicINFOID:0000000006224312
DTC DETECTION LOGIC
NOTE:
If DTC “C1A05” is detected along with DTC](/img/42/57033/w960_57033-824.png "INFINITI QX56 2011 Factory Service Manual
CCS-90
< DTC/CIRCUIT DIAGNOSIS >[ICC]
C1A05 BRAKE SW/STOP LAMP SW
C1A05 BRAKE SW/STOP LAMP SW
DTC LogicINFOID:0000000006224312
DTC DETECTION LOGIC
NOTE:
If DTC “C1A05” is detected along with DTC")
CCS-90
< DTC/CIRCUIT DIAGNOSIS >[ICC]
C1A05 BRAKE SW/STOP LAMP SW
C1A05 BRAKE SW/STOP LAMP SW
DTC LogicINFOID:0000000006224312
DTC DETECTION LOGIC
NOTE:
If DTC “C1A05” is detected along with DTC “U
1000”, first diagnose the DTC “U1000”. Refer to CCS-145,
"ADAS CONTROL UNIT : DTC Logic".
Diagnosis ProcedureINFOID:0000000006224313
1.CHECK SELF-DIAGNOSIS RESULTS
1. Perform “All DTC Reading” with CONSULT-III.
2. Check if the “U1000” is detected other than “C1A 05” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communication system inspecti on. Repair or replace the malfunctioning parts.
Refer to CCS-145, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK STOP LAMP SWITCH AND ICC BRAKE SWITCH
Check that “STOP LAMP SW” and “BRAKE SW” operate normally in “DATA MONITOR” of “ICC/ADAS”.
Is the inspection result normal?
YES >> GO TO 3.
NO-1 >> When “BRAKE SW” operation is malfunctioning: GO TO 4.
NO-2 >> When “STOP LAMP SW” operation is malfunctioning: GO TO 9.
3.CHECK STOP LAMP SWITCH
Check that “STOP LAMP SW” operate norma lly in “DATA MONITOR” of “ABS”.
Is the inspection result normal?
YES >> GO TO 14.
NO >> GO TO 9.
4.CHECK ICC BRAKE SWITCH INSTALLATION
1. Turn ignition switch OFF.
2. Check ICC brake switch for correct installation. Refer to BR-7, "
Inspection and Adjustment".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Adjust ICC brake switch installation. Refer to BR-7, "
Inspection and Adjustment".
5.ICC BRAKE SWITCH INSPECTION
1. Disconnect ICC brake switch connector.
2. Check ICC brake switch. Refer to CCS-93, "
Component Inspection (ICC Brake Switch)".
Is the inspection result normal?
DTC
(On board dis-
play) Trouble diagnosis
name DTC detecting condition Possible causes
C1A05 (5) BRAKE SW/STOP L
SW A mismatch between a stop lamp switch signal
and a ICC brake switch signal received from
ECM and a stop lamp signal received from the
ABS actuator and electric unit (control unit) con-
tinues for 10 seconds or more with vehicle
speeds at approximately 40 km/h or more Stop lamp switch circuit
ICC brake switch circuit
Stop lamp switch
ICC brake switch
Incorrect stop lamp switch installa-
tion
Incorrect ICC brake switch installa- tion
ECM
ABS actuator and electric unit (con-
trol unit)
Revision: 2010 May2011 QX56
Page 826 of 5598
![INFINITI QX56 2011 Factory Service Manual
CCS
C1A05 BRAKE SW/STOP LAMP SWCCS-91
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
YES >> GO TO 6.
NO >> Replace ICC brake switch.
6.CHECK ICC BRAKE SWITCH POWER SUPPLY CIRCUIT
1. Tu](/img/42/57033/w960_57033-825.png "INFINITI QX56 2011 Factory Service Manual
CCS
C1A05 BRAKE SW/STOP LAMP SWCCS-91
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
YES >> GO TO 6.
NO >> Replace ICC brake switch.
6.CHECK ICC BRAKE SWITCH POWER SUPPLY CIRCUIT
1. Tu")
CCS
C1A05 BRAKE SW/STOP LAMP SWCCS-91
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
YES >> GO TO 6.
NO >> Replace ICC brake switch.
6.CHECK ICC BRAKE SWITCH POWER SUPPLY CIRCUIT
1. Turn the ignition switch ON.
2. Check voltage between ICC brake switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair the harnesses or connectors.
7.CHECK HARNESS BETWEEN I CC BRAKE SWITCH AND ECM
1. Turn ignition switch OFF
2. Disconnect ECM connector.
3. Check for continuity between ICC brake sw itch harness connector and ECM harness connector.
4. Check for continuity between ICC br ake switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 8.
NO >> Repair the harnesses or connectors.
8.PERFORM SELF-DIAGNOSIS OF ECM
1. Connect all connectors again if the connectors are disconnected.
2. Turn ignition switch ON.
3. Perform “All DTC Reading”.
4. Check if any DTC is detected in “Self Diagnostic Result” of “ENGINE”. Refer to EC-98, "
DTC Index".
Is any DTC detected?
YES >> Repair or replace the malfunctioning part s identified by the self-diagnosis result.
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
9.CHECK STOP LAMP SWITCH INSTALLATION
1. Turn ignition switch OFF.
2. Check stop lamp switch for correct installation. Refer to BR-7, "
Inspection and Adjustment".
Is the inspection result normal?
YES >> GO TO 10.
NO >> Adjust stop lamp switch installation. Refer to BR-7, "
Inspection and Adjustment".
10.STOP LAMP SWITCH INSPECTION
1. Disconnect stop lamp switch connector.
2. Check stop lamp switch. Refer to CCS-93, "
Component Inspection (Stop Lamp Switch)".
Is the inspection result normal?
YES >> GO TO 11.
Te r m i n a l s
Vo l ta g e
(Approx.)
(+) (-)
ICC brake switch Ground
Connector Terminal
E68 1 Battery voltage
ICC brake switch ECM Continuity
Connector Terminal Connector Terminal
E68 2 E80 147 Existed
ICC brake switch GroundContinuity
Connector Terminal
E68 2 Not existed
Revision: 2010 May2011 QX56
Page 827 of 5598
![INFINITI QX56 2011 Factory Service Manual
CCS-92
< DTC/CIRCUIT DIAGNOSIS >[ICC]
C1A05 BRAKE SW/STOP LAMP SW
NO >> Replace stop lamp switch.
11 .CHECK STOP LAMP SWITCH
POWER SUPPLY CIRCUIT
1. Turn the ignition switch ON.
2. Check voltage be](/img/42/57033/w960_57033-826.png "INFINITI QX56 2011 Factory Service Manual
CCS-92
< DTC/CIRCUIT DIAGNOSIS >[ICC]
C1A05 BRAKE SW/STOP LAMP SW
NO >> Replace stop lamp switch.
11 .CHECK STOP LAMP SWITCH
POWER SUPPLY CIRCUIT
1. Turn the ignition switch ON.
2. Check voltage be")
CCS-92
< DTC/CIRCUIT DIAGNOSIS >[ICC]
C1A05 BRAKE SW/STOP LAMP SW
NO >> Replace stop lamp switch.
11 .CHECK STOP LAMP SWITCH
POWER SUPPLY CIRCUIT
1. Turn the ignition switch ON.
2. Check voltage between stop lamp switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 12.
NO >> Repair the harnesses or connectors.
12.CHECK HARNESS BETWEEN STOP LAMP SWITCH AND ECM
1. Turn ignition switch OFF
2. Disconnect ECM, rear combination la mp and high-mounted stop lamp connectors.
3. Check for continuity between stop lamp s witch harness connector and ECM harness connector.
4. Check for continuity between stop la mp switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 13.
NO >> Repair the harnesses or connectors.
13.CHECK HARNESS BETWEEN STOP LAMP SWIT CH AND ABS ACTUATOR AND ELECTRIC UNIT
(CONTROL UNIT)
1. Disconnect ABS actuator and electric unit (control unit) connector.
2. Check for continuity between stop lamp switch harness connector and ABS actuator and electric unit
(control unit) harness connector.
3. Check for continuity between stop la mp switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 14.
NO >> Repair the harnesses or connectors.
Te r m i n a l s Voltag e
(Approx.)
(+) (-)
Sto p l am p s w it ch
Ground
Connector Terminal
E115 1
Battery voltage
3
Stop lamp switch ECM Continuity
Connector Terminal Connector Terminal
E115 2 E80 158 Existed
Stop lamp switch GroundContinuity
Connector Terminal
E115 2 Not existed
Stop lamp switch ABS actuator and electric
unit (control unit) Continuity
Connector Terminal Connector Terminal
E115 4 E36 17 Existed
Stop lamp switch GroundContinuity
Connector Terminal
E115 4 Not existed
Revision: 2010 May2011 QX56
Page 828 of 5598
![INFINITI QX56 2011 Factory Service Manual
CCS
C1A05 BRAKE SW/STOP LAMP SWCCS-93
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
14.PERFORM SELF-DIAGNOSIS OF ECM
1. Connect all connectors again if the connectors are disconnecte](/img/42/57033/w960_57033-827.png "INFINITI QX56 2011 Factory Service Manual
CCS
C1A05 BRAKE SW/STOP LAMP SWCCS-93
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
14.PERFORM SELF-DIAGNOSIS OF ECM
1. Connect all connectors again if the connectors are disconnecte")
CCS
C1A05 BRAKE SW/STOP LAMP SWCCS-93
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
14.PERFORM SELF-DIAGNOSIS OF ECM
1. Connect all connectors again if the connectors are disconnected.
2. Turn ignition switch ON.
3. Perform “All DTC Reading”.
4. Check if any DTC is detected in “Self Diagnostic Result” of “ENGINE”. Refer to EC-98, "
DTC Index".
Is any DTC detected?
YES >> Repair or replace the malfunctioning part s identified by the self-diagnosis result.
NO >> GO TO 15.
15.PERFORM SELF-DIAGNOSIS OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”. Refer to BRC-51, "
DTC Index".
Is any DTC detected?
YES >> Repair or replace the malfunctioning part s identified by the self-diagnosis result.
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
Component Inspection (ICC Brake Switch)INFOID:0000000006224314
1.CHECK ICC BRAKE SWITCH
Check for continuity between I CC brake switch terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace ICC brake switch.
Component Inspection (Stop Lamp Switch)INFOID:0000000006224315
1.CHECK STOP LAMP SWITCH
Check for continuity between stop lamp switch terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace stop lamp switch.
Terminal Condition Continuity
12 When brake pedal is depressed
Not exist-
ed
When brake pedal is released Existed
Terminal Condition Continuity
12 When brake pedal is depressed Existed
When brake pedal is released
Not exist-
ed
34 When brake pedal is depressed Existed
When brake pedal is released
Not exist-
ed
Revision: 2010 May2011 QX56
Page 829 of 5598
![INFINITI QX56 2011 Factory Service Manual
CCS-94
< DTC/CIRCUIT DIAGNOSIS >[ICC]
C1A06 OPERATION SW
C1A06 OPERATION SW
DTC LogicINFOID:0000000006224316
DTC DETECTION LOGIC
NOTE:
If DTC “C1A06” is detected along with DTC “U
1000”, firs](/img/42/57033/w960_57033-828.png "INFINITI QX56 2011 Factory Service Manual
CCS-94
< DTC/CIRCUIT DIAGNOSIS >[ICC]
C1A06 OPERATION SW
C1A06 OPERATION SW
DTC LogicINFOID:0000000006224316
DTC DETECTION LOGIC
NOTE:
If DTC “C1A06” is detected along with DTC “U
1000”, firs")
CCS-94
< DTC/CIRCUIT DIAGNOSIS >[ICC]
C1A06 OPERATION SW
C1A06 OPERATION SW
DTC LogicINFOID:0000000006224316
DTC DETECTION LOGIC
NOTE:
If DTC “C1A06” is detected along with DTC “U
1000”, first diagnose the DTC “U1000”. Refer to CCS-145,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Wait for approximately 5 minutes after tu rning the MAIN switch of ICC system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “C1A06” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“C1A06” detected as the current malfunction?
YES >> Refer to CCS-94, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006224317
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected ot her than “C1A06” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communication system inspecti on. Repair or replace the malfunctioning parts.
Refer to CCS-145, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ICC STEERING SWITCH
1. Turn the ignition switch OFF.
2. Disconnect the ICC steering switch connector.
3. Check the ICC steering switch. Refer to CCS-95, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace the steering wheel.
3.CHECK HARNESS BETWEEN SPIRAL CABLE AND ECM
1. Disconnect the ECM connector.
2. Check for continuity between the spiral cable harness connector and ECM harness connector.
3. Check for continuity between spiral cable harness connector and ground.
DTC
(On board dis-
play) Trouble diagnosis
name DTC detecting condition Possible causes
C1A06 (6) OPERATION SW
CIRC Any switch of the ICC steering switch is de-
tected as “ON” continuously for 60 seconds
An ON/OFF state judgment of the ICC differs
between ECM and ADAS control unit, and the
state continues for 2 seconds or more ICC steering switch circuit
ICC steering switch
ECM
Spiral cable ECM
Continuity
Connector Terminal Connector Terminal
M33 25
E80 128
Existed
32 130
Revision: 2010 May2011 QX56
Page 830 of 5598
![INFINITI QX56 2011 Factory Service Manual
CCS
C1A06 OPERATION SWCCS-95
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair the harnesses or connectors.
4.CHECK SPIRAL CA](/img/42/57033/w960_57033-829.png "INFINITI QX56 2011 Factory Service Manual
CCS
C1A06 OPERATION SWCCS-95
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair the harnesses or connectors.
4.CHECK SPIRAL CA")
CCS
C1A06 OPERATION SWCCS-95
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair the harnesses or connectors.
4.CHECK SPIRAL CABLE
Check for continuity between spiral cable terminals.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace the spiral cable.
5.PERFORM SELF-DIAGNOSIS OF ECM
1. Connect the connectors of ICC st eering switch and ECM connector.
2. Turn the ignition switch ON.
3. Perform “All DTC Reading”.
4. Check if any DTC is detected in “Self Diagnostic Result” of “ENGINE”.
Is any DTC detected?
YES >> Perform self-diagnosis on the detected DTC and re pair or replace the malfunctioning parts. Refer
to EC-98, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
Component InspectionINFOID:0000000006224318
1.CHECK ICC STEERING SWITCH
Check resistance between ICC steering switch terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace the steering wheel.
Spiral cable
GroundContinuity
Connector Terminal
M33 25
Not existed
32
Spiral cable Continuity
Te r m i n a l
13 25 Existed
16 32
Terminal Switch operation Resistance
[Ω ]
13 16 When pressing MAIN switch Approx. 0
When pressing dynamic driver assistance
switch
Approx. 267
When pressing CANCEL switch Approx. 615
When pressing DISTANCE switch Approx.
1090
When pressing SET/COAST switch Approx.
1805
When pressing RESUME/ACCELERATE
switch Approx.
2985
When all switches are not pressed Approx.
5415
JSOIA0319GB
Revision: 2010 May2011 QX56