lock INFINITI QX56 2011 Factory Service Manual

HAC-2
ACCS (ADVANCED CLIMATE CONTROL SYS-
TEM) : Automatic Intake Control (Exhaust Gas /
Outside Odor Detecting Mechanism) .....................
28
ACCS (ADVANCED CLIMATE CONTROL SYS-
TEM) : Plasmacluster Control .................................
29
OPERATION ......................................................30
FRONT AUTOMATIC AIR CONDITIONING SYS-
TEM ........................................................................ ...
30
FRONT AUTOMATIC AIR CONDITIONING SYS-
TEM : Switch Name and Function ....................... ...
30
REAR AUTOMATIC AIR CONDITIONING SYS-
TEM ........................................................................ ...
35
REAR AUTOMATIC AIR CONDITIONING SYS-
TEM : Switch Name and Function ....................... ...
35
ACCS (ADVANCED CLIMATE CONTROL SYS-
TEM) ....................................................................... ...
37
ACCS (ADVANCED CLIMATE CONTROL SYS-
TEM) : Switch Name and Function .........................
37
DIAGNOSIS SYSTEM (HVAC) ..........................39
Description ........................................................... ...39
CONSULT-III Function ...........................................39
ECU DIAGNOSIS INFORMATION ..............42
A/C AUTO AMP. ............................................. ...42
Reference Value .................................................. ...42
Fail-safe ..................................................................45
DTC Index ..............................................................45
ECM, IPDM E/R .................................................47
List of ECU Reference ......................................... ...47
WIRING DIAGRAM .....................................48
AUTOMATIC AIR CONDITIONING SYSTEM ...48
Wiring Diagram .................................................... ...48
BASIC INSPECTION ...................................60
DIAGNOSIS AND REPAIR WORK FLOW ..... ...60
Work Flow ............................................................ ...60
OPERATION INSPECTION ............................ ...62
FRONT AUTOMATIC AIR CONDITIONING SYS-
TEM ........................................................................ ...
62
FRONT AUTOMATIC AIR CONDITIONING SYS-
TEM : Work Procedure ........................................ ...
62
REAR AUTOMATIC AIR CONDITIONING SYS-
TEM ........................................................................ ...
64
REAR AUTOMATIC AIR CONDITIONING SYS-
TEM : Work Procedure ........................................ ...
64
ACCS (ADVANCED CLIMATE CONTROL SYS-
TEM) ....................................................................... ...
66
ACCS (ADVANCED CLIMATE CONTROL SYS-
TEM) : Work Procedure ..........................................
66
SYSTEM SETTING ............................................68
FRONT AUTOMATIC AIR CONDITIONING SYS-
TEM ........................................................................ ...
68
FRONT AUTOMATIC AIR CONDITIONING SYS-
TEM : Temperature Setting Trimmer (Front) ..........
68
FRONT AUTOMATIC AIR CONDITIONING SYS-
TEM : Foot Position Setting Trimmer ......................
68
FRONT AUTOMATIC AIR CONDITIONING SYS-
TEM : Inlet Port Memory Function (FRE) ................
69
FRONT AUTOMATIC AIR CONDITIONING SYS-
TEM : Inlet Port Memory Function (REC) ...............
69
REAR AUTOMATIC AIR CONDITIONING SYS-
TEM ........................................................................ ...
69
REAR AUTOMATIC AIR CONDITIONING SYS-
TEM : Temperature Setting Trimmer (Rear) ...........
69
ACCS (ADVANCED CLIMATE CONTROL SYS-
TEM) ....................................................................... ...
70
ACCS (ADVANCED CLIMATE CONTROL SYS-
TEM) : Exhaust Gas / Outside Odor Detecting
Sensor Sensitivity Adjustment Function ..................
70
ACCS (ADVANCED CLIMATE CONTROL SYS-
TEM) : Auto Intake Switch Interlocking Movement
Change Function .....................................................
70
DTC/CIRCUIT DIAGNOSIS ........................72
U1000 CAN COMM CIRCUIT ......................... ...72
Description ........................................................... ...72
DTC Logic ...............................................................72
Diagnosis Procedure ...............................................72
U1010 CONTROL UNIT (CAN) .........................73
Description ........................................................... ...73
DTC Logic ...............................................................73
Diagnosis Procedure ...............................................73
B2578, B2579 FRONT IN-VEHICLE SENSOR ...74
DTC Logic ............................................................ ...74
Diagnosis Procedure ...............................................74
Component Inspection ............................................75
B257B, B257C AMBIENT SENSOR .................77
DTC Logic ............................................................ ...77
Diagnosis Procedure ...............................................77
Component Inspection ............................................78
B2581, B2582 INTAKE SENSOR .....................80
DTC Logic ............................................................ ...80
Diagnosis Procedure ...............................................80
Component Inspection ............................................81
B262A, B262B, B2657, B2658 EXHAUST
GAS/OUTSIDE ODOR DETECTING SENSOR
...
83
DTC Logic ............................................................ ...83
Diagnosis Procedure ...............................................83
Revision: 2010 May2011 QX56

SYSTEMHAC-29
< SYSTEM DESCRIPTION > [AUTOMATIC AIR CONDITIONING]
C
D
E
F
G H
J
K L
M A
B
HAC
N
O P
 Sensitivity of exhaust gas / out side odor detecting sensor can be changed by “GAS SENSOR ADJUST-
MENT” in “WORK SUPPORT” mode of CONSULT-III. Refer to HAC-70, "
ACCS (ADVANCED CLIMATE
CONTROL SYSTEM) : Exhaust Gas / Outside Odor Detecting Sensor Sensitivity Adjustment Function".
 Automatic intake control (exhaust gas / outside odor detecting mechanism) does not operate when ambient
temperature is −2 °C (28 °F) or less. In this case, control is only for control of automatic air inlet of automatic
air conditioning system.
ACCS (ADVANCED CLIMATE CONTROL SYSTEM) : Plasmacluster Control
INFOID:0000000006275878
DESCRIPTION
Plasmacluster™ control eliminates microbes and reduces odor on interior surface by including high density
Plasmacluster
™ ion in air conditioning outlet air flow.
OPERATION DESCRIPTION
 Plasmacluster™ control operates by interlocking to blower motor. Plasmacluster™ control operates when
blower motor operates.
 Control status is displayed on front air conditioning system display screen. Refer to HAC-37, "
ACCS
(ADVANCED CLIMATE CONTROL SYSTEM) : Switch Name and Function".
NOTE:
 Plasmacluster
™ ion technology developed by Sharp Corporation is installed in this item.
 Plasmacluster
™ is a trademark of Sharp Corporation.
Revision: 2010 May2011 QX56

HAC-32
< SYSTEM DESCRIPTION >[AUTOMATIC AIR CONDITIONING]
OPERATION
WITHOUT ACCS (ADVANCED CLIMATE CONTROL SYSTEM)
A/C Display
 Front air conditioning system state is indicated on the display.
 When “STATUS” on multifunction switch is pressed while
front air conditioning system is in the ON position,
the display changes to state indication display of fr ont air conditioning system. When front air conditioning
system is operated while navigation system or audio system is displayed, front air conditioning system state
is indicated in the lower portion of display for several seconds.
 When MODE switch is pressed while front air conditioni ng system is in the OFF position, state indication dis-
play is indicated for several seconds.
Display Screen
Controller (Preset Switch)
Intake switch Air inlet changes between recirculation (REC)
⇔ fresh air intake (FRE) each time this switch is
pressed.
 Intake switch indicator ON: Recirculation
 Intake switch indicator OFF: Fresh air intake
NOTE:
 When front air conditioning system is in the OFF position, air inlet can be selected.
 When MODE switch and DEF switch is in the D/F or DEF position, air inlet cannot be selected to recirculation (REC).
Temperature control dial
(driver side)  Selects set temperature within a range between 18.0
°C (60 °F) – 32.0 °C (90 °F) at a rate of 0.5 °C
(1.0 °F) each time the dial is rotated.
- Clockwise rotation: Set temperature increases.
- Counterclockwise rotation: Set temperature decreases.
NOTE:
When front air conditioning system is in the OFF position, set temperature can be selected only while
front air conditioning system state (when MODE switch is pressed) is indicated on the display.
Temperature control dial
(passenger side)  Selects set temperature within a range between 18.0
°C (60 °F) – 32.0 °C (90 °F) at a rate of 0.5 °C
(1.0 °F) each time the dial is rotated.
- Clockwise rotation: Set temperature increases.
- Counterclockwise rotation: Set temperature decreases.
 When the temperature control dial is turned, DUAL switch indicator turns ON.
NOTE:
When front air conditioning system is in the OFF position, set temperature can be selected only while
front air conditioning system state (when MODE switch is pressed) is indicated on the display.
Upper ventilator switch Turns the upper ventilator control (switch indicator) between ON
⇔ OFF each time while front blower
fan is activated.
NOTE:
 When front air conditioning system is in the OFF position and air outlet is DEF position, upper ven- tilator control cannot be activated.
 When front air conditioning system is in the OFF position, upper ventilator control can be selected
only while front air conditioning system state (when MODE switch is pressed) is indicated on the
display.
JMIIA0719GB
Revision: 2010 May2011 QX56

HAC-34
< SYSTEM DESCRIPTION >[AUTOMATIC AIR CONDITIONING]
OPERATION
DUAL switch Turns left and right ventilation temperature separately control (switch indicator) between ON
⇔
OFF each time.
 When DUAL switch indicator is ON, the driver side and passenger side temperatures can each be set independently.
 When DUAL switch indicator is OFF, the driver side outlet and setting temperature is applied to both
sides.
 Left and right ventilation temperature separately control is cancelled by turning the DEF mode ON.
NOTE:
When front air conditioning system is in the OFF position, left and right ventilation temperature sepa-
rately control can be selected only while front air conditioning system state (when MODE switch is
pressed) is indicated on the display.
Fan switch (UP/DOWN) Blower fan speed is manually controlled with these switches. Seven speeds are available for manual
control (as shown on the display screen)
NOTE:
 When fan switch is pressed while front air conditioning system is in OFF, front air conditioning sys-
tem is activated. (Compressor control state returns to the previous state before front air condition-
ing system OFF.)
 When fan switch is pressed while front air conditioning system is in automatic control (“AUTO” is
indicated), automatic control is released (“AUTO” turns OFF).
FRE switch  Air inlet is selected to fresh air intake (FRE) by pressing this switch.
- FRE indicator: ON
- REC indicator: OFF
 When FRE indicator is ON, pressing the FRE switch for approximately 1.5 seconds or more, and
then the FRE and REC switch indicators blink twice and the system is switched to the automatic
control.
NOTE:
When front air conditioning system is in the OFF position, air inlet can be selected.
MODE switch Selects air outlet sequentially from VENT
⇒ B/L ⇒ FOOT ⇒ D/F ⇒ VENT each time.
NOTE:
 When front air conditioning system is in the OFF position, air outlet can be selected.
 When MODE switch is pressed while front air conditioning system is in automatic control (“AUTO” is indicated), automatic control is released (“AUTO” turns OFF).
OFF switch  Turns front air conditioning system OFF.
 When front air conditioning system turns OFF, air inlet and air outlet become the automatic control.
REC switch  Air inlet is selected to fresh air intake (REC) by pressing this switch.
- REC indicator: ON
- FRE indicator: OFF
 When REC indicator is ON, pressing the REC switch for approximately 1.5 seconds or more, and
then the FRE and REC switch indicators blink twice and the system is switched to the automatic
control.
NOTE:
 When front air conditioning system is in the OFF position, air inlet can be selected.
 When MODE switch and DEF switch is in the D/F or DEF position, air inlet cannot be selected to recirculation (REC).
Temperature control dial
(driver side)  Selects set temperature within a range between 18.0
°C (60 °F) – 32.0 °C (90 °F) at a rate of 0.5 °C
(1.0 °F) each time the dial is rotated.
- Clockwise rotation: Set temperature increases.
- Counterclockwise rotation: Set temperature decreases.
NOTE:
When front air conditioning system is in the OFF position, set temperature can be selected only while
front air conditioning system state (when MODE switch is pressed) is indicated on the display.
Revision: 2010 May2011 QX56

OPERATIONHAC-35
< SYSTEM DESCRIPTION > [AUTOMATIC AIR CONDITIONING]
C
D
E
F
G H
J
K L
M A
B
HAC
N
O P
REAR AUTOMATIC AIR CONDITIONING SYSTEM
REAR AUTOMATIC AIR CONDITIONING SY STEM : Switch Name and Function
INFOID:0000000006275882
FRONT CONTOLLER OPERATION
A/C Display
 Rear air conditioning system state is indicated on the front display.
 When REAR switch is pressed while air conditioning syst em is in the ON position, the front display changes
to state indication display (rear contro l mode) of rear air conditioning system.
Display screen
Controller (Preset Switch)
With ACCS (advanced climate control system)
Temperature control dial
(passenger side)  Selects set temperature within a range between 18.0
°C (60 °F) – 32.0 °C (90 °F) at a rate of 0.5 °C
(1.0 °F) each time the dial is rotated.
- Clockwise rotation: Set temperature increases.
- Counterclockwise rotation: Set temperature decreases.
 When the temperature control dial is turned, DUAL switch indicator turns ON.
NOTE:
When front air conditioning system is in the OFF position, set temperature can be selected only while
front air conditioning system state (when MODE switch is pressed) is indicated on the display.
Upper ventilator switch Turns the upper ventila
tor control (switch indicator) between ON ⇔ OFF each time while front blower
fan is activated.
NOTE:
 When front air conditioning system is in the OFF position and air outlet is DEF position, upper ven- tilator control cannot be activated.
 When front air conditioning system is in the OFF position, upper ventilator control can be selected only while front air conditioning system state (when MODE switch is pressed) is indicated on the
display.
JMIIA0720ZZ
JMIIA0825ZZ
1. AUTO switch 2. Temperature control dial (Driver
side)3. MODE switch
4. REAR switch 5. OFF switch 6. Fan switch
Revision: 2010 May2011 QX56

HAC-36
< SYSTEM DESCRIPTION >[AUTOMATIC AIR CONDITIONING]
OPERATION
Without ACCS (advanced
climate control system)
Switch Operation
REAR CONTROLLER OPERATION
Controller (Rear A/C Control)
JMIIA0824ZZ
1. AUTO switch 2. Temperature control dial (Driver
side)3. MODE switch
4. REAR switch 5. OFF switch 6. Fan switch
AUTO switch Turns the switch indicator lamp and "AUTO" indicator on the front display ON, and then rear air con-
ditioning system becomes the following state.
 Air outlet: Automatic control
 Blower fan: Automatic control
 Compressor: ON
Fan switch (UP/DOWN) Blower fan speed is manually controlled with these switches. Seven speeds are available for manual
control (as shown on the display screen)
NOTE:
When fan switch is pressed while air conditioning system is in automatic control (“AUTO” is indicated),
automatic control is rele
ased (“AUTO” turns OFF).
MODE switch Selects air outlet sequentially from VENT
⇒ B/L ⇒ FOOT ⇒ VENT each time.
NOTE:
When MODE switch is pressed while air conditioning system is in automatic control (“AUTO” is indi-
cated), automatic control is released (“AUTO” turns OFF).
OFF switch  Turns rear air conditioning system OFF. (When rear control mode is ON)
 When rear air conditioning system turns OFF, air outlet become the automatic control.
REAR switch  Turns the switch indicator lamp and rear control mode on the front display ON, and then rear air
conditioning system becomes the following state.
- Air outlet: Automatic control
- Blower fan: Automatic control
- Compressor: ON
 Rear control mode is released when switch is pressed again (rear air conditioning system operates continuously).
Temperature control dial
(driver side)  Selects set temperature within a range between 18.0
°C (60 °F) – 32.0 °C (90 °F) at a rate of 0.5 °C
(1.0 °F) each time the dial is rotated.
- Clockwise rotation: Set temperature increases.
- Counterclockwise rotation: Set temperature decreases.
Revision: 2010 May2011 QX56

HAC-38
< SYSTEM DESCRIPTION >[AUTOMATIC AIR CONDITIONING]
OPERATION
- When air flow is small
- When air flow is large
Controller (Preset Switch)
JMIIA0410ZZ
JMIIA0411ZZ
1. Auto intake switch
Switch name Function
Auto intake switch  Automatic intake control (exhaust gas / outside odor detecting mechanism) mode (switch indicator)
changes between ON ⇔ OFF each time when auto intake switch is pressed while front blower mo-
tor is activated.
 When auto intake switch turns ON, front air conditioning system becomes the following status.
- A/C switch: ON
- Air inlet: Recirculation [After approximately 5 minutes, air inlet is switched to automatic intake con- trol (exhaust gas / outside odor detecting mechanism).]
 When auto intake switch turns ON ⇒ OFF, air inlet becomes the fresh air intake.
NOTE:
 Interlocking condition of A/C switch can be changed. Refer to HAC-70, "
ACCS (ADVANCED CLI-
MATE CONTROL SYSTEM) : Auto Intake Switch Interlocking Movement Change Function".
 Auto intake switch does not turn ON during the following status.
- Air outlet: DEF
- Ambient temperature: −2 °C (28 °F) or less
JMIIA0826ZZ
Revision: 2010 May2011 QX56

DIAGNOSIS SYSTEM (HVAC)HAC-41
< SYSTEM DESCRIPTION > [AUTOMATIC AIR CONDITIONING]
C
D
E
F
G H
J
K L
M A
B
HAC
N
O P
*: With ACCS (advanced climate control system)
NOTE:
Perform the inspection of each output device after starting the engine because the compressor is operated.
WORK SUPPORT
*: With ACCS (advanced climate control system)
NOTE:
When the battery cable is disconnected from the negative terminal or when the battery voltage becomes 10 V
or less, the setting of WORK SUPPORT may be cancelled.
Rear A/C relay ON ON ON ON OFF OFF ON
Ionizer
*ON ON ON ON ON ON OFF
Front display (Ion mode)
*CLEAN CLEAN QUICK
CLEAN QUICK
CLEAN QUICK
CLEAN QUICK
CLEAN OFF
Te s t i t e m
MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 MODE 6 MODE 7
Work item Description Refer to
TEMP SET CORRECT Setting change of temperature setting trimmer (front) can be per-
formed. HAC-68, "
FRONT AUTO-
MATIC AIR CONDITION-
ING SYSTEM :
Temperature Setting Trim-
mer (Front)"
BLOWER SET Setting change of foot position setting trimmer can be performed.
HAC-68, "
FRONT AUTO-
MATIC AIR CONDITION-
ING SYSTEM : Foot
Position Setting Trimmer"
REC MEMORY SET
Setting change of inlet port memory function (REC) can be per-
formed. HAC-69, "
FRONT AUTO-
MATIC AIR CONDITION-
ING SYSTEM : Inlet Port
Memory Function (REC)"
FRE MEMORY SET
Setting change of inlet port memory function (FRE) can be per-
formed. HAC-69, "
FRONT AUTO-
MATIC AIR CONDITION-
ING SYSTEM : Inlet Port
Memory Function (FRE)"
GAS SENSOR ADJUSTMENT*Setting change of exhaust gas / outside odor detecting sensor sensi-
tivity adjustment function can be performed. HAC-70, "
ACCS (AD-
VANCED CLIMATE CON-
TROL SYSTEM) :
Exhaust Gas / Outside
Odor Detecting Sensor
Sensitivity Adjustment
Function"
CLEAN SW SET*Setting change of auto intake switch interlocking movement change
function can be performed.
HAC-70, "
ACCS (AD-
VANCED CLIMATE CON-
TROL SYSTEM) : Auto
Intake Switch Interlocking
Movement Change Func-
tion"
REAR TEMP SET CORRECT
Setting change of temperature setting trimmer (rear) can be per-
formed. HAC-68, "
FRONT AUTO-
MATIC AIR CONDITION-
ING SYSTEM :
Temperature Setting Trim-
mer (Front)"
Revision: 2010 May2011 QX56

HAC-70
< BASIC INSPECTION >[AUTOMATIC AIR CONDITIONING]
SYSTEM SETTING
If the temperature felt by the customer is different from
the rear air flow temperature controlled by the temper-
ature setting, the A/C auto amp. control temperature can be adjusted to compensate for the temperature set-
ting.
HOW TO SET
With CONSULT-III
Perform “REAR TEMP SET CORRECT” of HVAC work support item.
NOTE:
 When −3.0 °C ( −6 °F) is corrected on the temperature setting set as 25.0 °C (77 °F) the temperature controlled
by A/C auto amp. is 25.0 °C (77 °F) −3.0 °C ( −6 °F) = 22.0 °C (72 °F) and the temperature becomes lower than
the temperature setting.
 When the battery cable is disconnected from the negativ e terminal or when the battery voltage becomes 10
V or less, the setting of the difference between t he set temperature and control temperature may be can-
celled.
ACCS (ADVANCED CLIM ATE CONTROL SYSTEM)
ACCS (ADVANCED CLIMATE CONTROL SYSTE M) : Exhaust Gas / Outside Odor
Detecting Sensor Sensitiv ity Adjustment Function
INFOID:0000000006275901
DESCRIPTION
According to customer’s sense of smell, exhaust gas / outside odor detecting sensor sensitivity can be
changed.
HOW TO SET
With CONSULT-III
Perform the “GAS SENSOR ADJUSTME NT” of HVAC work support item.
NOTE:
When the battery cable is disconnected from the negativ e terminal or when the battery voltage becomes 10 V
or less, the setting of WORK SUPPORT may be cancelled.
ACCS (ADVANCED CLIMATE CONTROL SYSTEM) : Auto Intake Switch Interlocking
Work support items Display ( °C) Display ( °F)
REAR TEMP SET CORRECT 3.0 6
2.5 5
2.0 4
1.5 3
1.0 2
0.5 1
0 (initial status) 0 (initial status) −0.5 −1
− 1.0 −2
− 1.5 −3
− 2.0 −4
− 2.5 −5
− 3.0 −6
Work support items Display Setting
GAS SENSOR ADJUSTMENT 2 Less sensitive setting than display 1 (REC later than display 1.)
1 Less sensitive setting than normal setting (REC later than normal operation.)
0 (initial status) Normal −1 More sensitive setting than normal setting (REC earlier than normal operation.)
− 2 More sensitive setting than display −1 (REC earlier than display −1.)
Revision: 2010 May2011 QX56

SYSTEM SETTINGHAC-71
< BASIC INSPECTION > [AUTOMATIC AIR CONDITIONING]
C
D
E
F
G H
J
K L
M A
B
HAC
N
O P
Movement Change FunctionINFOID:0000000006275902
DESCRIPTION
Condition for interlocking movement of auto intake switch and A/C switch can be changed. In addition opera-
tion of the auto intake switch, which activates the aut omatic intake control (exhaust gas / outside odor detect-
ing mechanism), can be set to become available when the A/C switch is ON.
HOW TO SET
With CONSULT-III
Perform the “CLEAN SW SET” of HVAC work support item.
NOTE:
When the battery cable is disconnect ed from the negative terminal or when the battery voltage becomes 10 V
or less, the setting of WO RK SUPPORT may be cancelled.
Work support items Display Setting
CLEAN SW SET Mode1 Initial setting
Mode2 Setting 1
Mode3 Setting 2
Mode4 Setting 3
Initial setting
When the auto intake switch is ON, the A/C switch is al
so turned ON in synchronization with the auto intake
switch.
Control of the auto intake switch is function al even when the A/C switch is turned OFF.
Setting 1 When the auto intake switch is ON, the A/C switch is
not turned ON in synchronization with the auto intake
switch.
Control of the auto intake switch is function al even when the A/C switch is turned OFF.
Setting 2 When the auto intake switch is ON, the A/C switch is al
so turned ON in synchronization with the auto intake
switch.
When the A/C switch is turned OFF, the auto intake switch is turned OFF in synchronization with the A/C
switch.
Setting 3 Auto intake switch can be turned ON only when A/C switch is ON.
When the A/C switch is turned OFF, the auto intake switch is turned OFF in synchronization with the A/C
switch.
Revision: 2010 May2011 QX56