warning INFINITI QX56 2011 Factory Manual PDF

PARKING BRAKE SWITCHBRC-117
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
PARKING BRAKE SWITCH
Component Function CheckINFOID:0000000006222643
1.CHECK PARKING BRA KE SWITCH OPERATION
Check that brake warning lamp in combination meter turns ON/OFF when parking brake is operated.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Proceed to diagnosis procedure. Refer to BRC-117, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006222644
1.CHECK PARKING BRAKE SWITCH CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect parking brake switch harness connector.
3. Disconnect combination meter harness connector.
4. Check continuity between parking brake switch harness connector and combination meter harness con-
nector.
5. Check continuity between parking brake switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.CHECK PARKING BRAKE SWITCH
Check parking brake switch. Refer to BRC-118, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace parking brake switch. Refer to PB-5, "
Removal and Installation".
3.CHECK PARKING BRAKE SWITCH SIGNAL
With CONSULT-III.
1. Connect parking brake switch harness connector.
2. Connect combination meter harness connector.
3. Select “ABS”, “DATA MONITOR” and “PARK BRAKE SW ” according to this order. Check parking brake
switch signal.
Is the inspection result normal?
YES >> INSPECTION END
NO >> GO TO 4.
4.CHECK COMBINATION METER
Check combination meter. Refer to MWI-30, "
CONSULT-III Function".
Parking brake switch Combination meter
Continuity
Connector Terminal Connector Terminal
M11 1 M34 26 Existed
Parking brake switch —Continuity
Connector Terminal
M11 1 Ground Not existed
Condition DATA MONITOR
Operate parking brake On
Release the parking brake Off
Revision: 2010 May2011 QX56

BRC-122
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
ABS WARNING LAMP
ABS WARNING LAMP
Component Function CheckINFOID:0000000006222649
1.CHECK ABS WARNING LAMP FUNCTION
Check that ABS warning lamp in combination meter turns ON for approx. 1 second after ignition switch is
turned ON.
CAUTION:
Never start engine.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Proceed to diagnosis procedure. Refer to BRC-122, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006222650
1.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Perform the trouble diagnosis for ABS actuator and elec tric unit (control unit) power supply and ground circuit.
Refer to BRC-113, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.PERFORM THE SELF-DIAGNOSIS
With CONSULT-III.
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES >> Check the DTC. Refer to BRC-51, "DTC Index".
NO >> GO TO 3.
3.CHECK ABS WARNING LAMP SIGNAL
With CONSULT-III.
1. Select “ABS”, “DATA MONITOR” and “ABS WARN LAMP” according to this order.
2. Turn the ignition switch OFF.
3. Check that data monitor displays “On” for approx. 1 second after ignition switch is turned ON and then
changes to “Off”.
CAUTION:
Never start engine.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace ABS actuator and electric unit (control unit). Refer to BRC-137, "
Removal and Installa-
tion".
4.CHECK COMBINATION METER
Check combination meter. Refer to MWI-30, "
CONSULT-III Function".
Is the inspection result normal?
YES >> Replace ABS actuator and electr ic unit (control unit). Refer to BRC-137, "Removal and Installa-
tion".
NO >> Repair or replace combination meter. Refer to MWI-85, "
Removal and Installation".
Revision: 2010 May2011 QX56

BRAKE WARNING LAMPBRC-123
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
BRAKE WARNING LAMP
Component Function CheckINFOID:0000000006222651
1.CHECK BRAKE WARNING LAMP FUNCTION (1)
Check that brake warning lamp in combination meter turns ON for approx. 1 second after ignition switch is
turned ON.
CAUTION:
Never start engine.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Proceed to diagnosis procedure. Refer to BRC-123, "
Diagnosis Procedure".
2.CHECK BRAKE WARNING LAMP FUNCTION (2)
Check that brake warning lamp in combination meter turns ON/OFF when parking brake is operated.
NOTE:
Brake warning lamp turns ON when parking brake is operated (when parking brake switch is ON).
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check parking brake switch system. Refer to BRC-117, "
Diagnosis Procedure".
3.CHECK BRAKE WARNING LAMP FUNCTION (3)
Check that brake warning lamp in combination meter turns ON/OFF when brake fluid level switch is operated
while brake fluid level in reservoir tank is with the specified level.
NOTE:
Brake warning lamp turns ON when brake fluid is less than the specified level (when brake fluid level switch is
ON).
Is the inspection result normal?
YES >> INSPECTION END
NO >> Check brake fluid level switch system. Refer to BRC-103, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006222652
1.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Perform the trouble diagnosis for ABS actuator and elec tric unit (control unit) power supply and ground circuit.
Refer to BRC-113, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.PERFORM THE SELF-DIAGNOSIS
With CONSULT-III.
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES >> Check the DTC. Refer to BRC-51, "DTC Index".
NO >> GO TO 3.
3.CHECK BRAKE WARNING LAMP SIGNAL
With CONSULT-III.
1. Select “ABS”, “DATA MONITOR” and “EBD WARN LAMP” according to this order.
2. Turn the ignition switch OFF.
3. Check that data monitor displays “On” for approx. 1 second after ignition switch is turned ON and then changes to “Off”.
CAUTION:
Never start engine.
Is the inspection result normal?
Revision: 2010 May2011 QX56

BRC-124
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
BRAKE WARNING LAMP
YES >> GO TO 4.
NO >> Replace ABS actuator and electric unit (control unit). Refer to
BRC-137, "
Removal and Installa-
tion".
4.CHECK COMBINATION METER
Check combination meter. Refer to MWI-30, "
CONSULT-III Function".
Is the inspection result normal?
YES >> Replace ABS actuator and electr ic unit (control unit). Refer to BRC-137, "Removal and Installa-
tion".
NO >> Repair or replace combination meter. Refer to MWI-85, "
Removal and Installation".
Revision: 2010 May2011 QX56

VDC WARNING LAMPBRC-125
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
VDC WARNING LAMP
Component Function CheckINFOID:0000000006222653
1.CHECK VDC WARNING LAMP FUNCTION
Check that VDC warning lamp in combination meter turns ON for approx. 1 second after ignition switch is
turned ON.
CAUTION:
Never start engine.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Proceed to diagnosis procedure. Refer to BRC-125, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006222654
1.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Perform the trouble diagnosis for ABS actuator and elec tric unit (control unit) power supply and ground circuit.
Refer to BRC-113, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.PERFORM THE SELF-DIAGNOSIS
With CONSULT-III.
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES >> Check the DTC. Refer to BRC-51, "DTC Index".
NO >> GO TO 3.
3.CHECK VDC WARNING LAMP SIGNAL
With CONSULT-III.
1. Select “ABS”, “DATA MONITOR” and “SLI P/VDC LAMP” according to this order.
2. Turn the ignition switch OFF.
3. Check that data monitor displays “On” for approx. 1 second after ignition switch is turned ON and then
changes to “Off”.
CAUTION:
Never start engine.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace ABS actuator and electric unit (control unit). Refer to BRC-137, "
Removal and Installa-
tion".
4.CHECK COMBINATION METER
Check combination meter. Refer to MWI-30, "
CONSULT-III Function".
Is the inspection result normal?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-137, "Removal and Installa-
tion".
NO >> Repair or replace combination meter. Refer to MWI-85, "
Removal and Installation".
Revision: 2010 May2011 QX56

BRC-126
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
VDC OFF INDICATOR LAMP
VDC OFF INDICATOR LAMP
Component Function CheckINFOID:0000000006222655
1.CHECK VDC OFF INDICATO
R LAMP FUNCTION (1)
Check that VDC OFF indicator lamp in combination me ter turns ON for approx. 1 second after ignition switch
is turned ON.
CAUTION:
Never start engine.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Proceed to diagnosis procedure. Refer to BRC-126, "
Diagnosis Procedure"
2.CHECK VDC WARNING LAMP FUNCTION (2)
Check that VDC OFF indicator lamp in combination meter turns ON/OFF when VDC OFF switch is operated.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Check VDC OFF switch system. Refer to BRC-119, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006222656
1.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Perform the trouble diagnosis for ABS actuator and elec tric unit (control unit) power supply and ground circuit.
Refer to BRC-113, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.CHECK VDC OFF INDICATOR LAMP SIGNAL (1)
With CONSULT-III.
1. Select “ABS”, “DATA MONITOR” and “OFF LAMP” according to this order.
2. Turn the ignition switch OFF.
3. Check that data monitor displays “On” for approx. 1 second after ignition switch is turned ON and then
changes to “Off”.
CAUTION:
Never start engine.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace ABS actuator and electric unit (control unit). Refer to BRC-137, "
Removal and Installa-
tion".
3.CHECK VDC OFF INDICATOR LAMP SIGNAL (2)
With CONSULT-III.
1. Select “ABS”, “DATA MONITOR” and “OFF LAMP” according to this order.
2. Check that data monitor displays “On” or “Off” each time when VDC OFF switch is operated.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Check VDC OFF switch system. Refer to BRC-119, "
Diagnosis Procedure".
4.CHECK COMBINATION METER
Check combination meter. Refer to MWI-30, "
CONSULT-III Function".
Is the inspection result normal?
YES >> Replace ABS actuator and electr ic unit (control unit). Refer to BRC-137, "Removal and Installa-
tion".
NO >> Repair or replace combination meter. Refer to MWI-85, "
Removal and Installation".
Revision: 2010 May2011 QX56

EXCESSIVE OPERATION FREQUENCYBRC-127
< SYMPTOM DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
SYMPTOM DIAGNOSIS
EXCESSIVE OPERATION FREQUENCY
DescriptionINFOID:0000000006222657
VDC function, TCS function, ABS functi on, EBD function, hill start assist function and brake limited slip differ-
ential (BLSD) function operates in excessive operation frequency.
Diagnosis ProcedureINFOID:0000000006222658
1.CHECK BRAKING FORCE
Check brake force using a brake tester.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Check brake system.
2.CHECK FRONT AND REAR AXLE
Check that there is no excessive looseness in front and rear axle.
 Front axle: Refer to FA X - 7 , "
Inspection" (2WD), FAX-16, "Inspection" (4WD).
 Rear axle: Refer to RAX-5, "
Inspection"
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace error-detected parts.
3.CHECK WHEEL SENSOR
Check wheel sensor.
 Check installation and damage of wheel sensor.
 Check connection of wheel sensor harness connector.
 Check terminal of wheel sensor harness connector.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace wheel sensor.  Front wheel sensor: Refer to BRC-134, "
FRONT WHEEL SENSOR : Removal and Installation".
 Rear wheel sensor: Refer to BRC-135, "
REAR WHEEL SENSOR : Removal and Installation".
4.CHECK WARNING LAMP TURNS OFF
Check that ABS warning lamp, brake warning lamp and VDC warning lamp turn OFF approx. 1 second after
key switch is turned ON and stay in OFF status during driving.
CAUTION:
Brake warning lamp turns ON when parking brake is operated (parking brake switch is ON) or brake
fluid is less than the specified level (brake fluid level switch is ON).
Is the inspection result normal?
YES >> Normal
NO >> Perform self-diagnosis for “ABS” with CONSULT-III.
Revision: 2010 May2011 QX56

BRC-130
< SYMPTOM DIAGNOSIS >[WITH VDC]
DOES NOT OPERATE
DOES NOT OPERATE
DescriptionINFOID:0000000006222663
VDC function, TCS function, ABS functi
on, EBD function, hill start assist function and brake limited slip differ-
ential (BLSD) function does not operate.
Diagnosis ProcedureINFOID:0000000006222664
CAUTION:
 VDC function, ABS function and EBD function never operate when the vehicle speed is 10 km/h (6.2
MPH) or less.
 TCS function, hill start assist fu nction and brake limited slip diffe rential (BLSD) function operates
when the vehicle speed is 0 km/h (0 MPH) (the vehicle is in stop status).
 VDC function and TCS function never operate wh en VDC OFF switch is operated (when VDC OFF
indicator lamp turns ON).
1.CHECK ABS WARNING LAMP
Check that ABS warning lamp, brake warning lamp and VDC warning lamp turn ON and turn OFF approx. 1
second after key switch is turned ON. Check that ABS warning lamp, brake warning lamp and VDC warning
lamp and stay in OFF status during driving.
CAUTION:
Brake warning lamp turns ON when parking brake is operated (parking brake switch is ON) or brake
fluid is less than the specified level (brake fluid level switch is ON).
Is the inspection result normal?
YES >> Normal
NO >> Perform self-diagnosis for “ABS” with CONSULT-III.
Revision: 2010 May2011 QX56

NORMAL OPERATING CONDITIONBRC-133
< SYMPTOM DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
NORMAL OPERATING CONDITION
DescriptionINFOID:0000000006222669
Symptom Result
Brake pedal slightly vibrates and operation sound (motor sound and sound from suspen-
sion) occurs when VDC function, TCS function, ABS function, EBD function, hill start assist
function and brake limited slip differential (BLSD) function operates. This is not a malfunction, The symptom
occurs VDC function
, TCS function, ABS
function, EBD function, hill start assist
function and brake limited slip differential
(BLSD) function that are normally operat-
ed.
Brake stopping distance may become longer than models without ABS function depending
on the road conditions, when
ABS function is operated on slip pery road like rough road,
gravel road or snowy road.
Brake pedal vibrates and operation sound occurs during sudden acceleration and corner-
ing, when VDC function, TCS function, hill start assist function and brake limited slip differ-
ential (BLSD) function is operated.
Brake pedal vibrates and motor sound from the engine room occurs, when the engine starts
or the vehicle starts just after starting the engine This is not a malfunction. The symptom
occurs during the brake fluid accumula-
tion in the accumulator and operational
check of the ABS actuator and electric
unit (control unit).
Acceleration may be felt insufficient depending on the road conditions. This is not a malfunction. The symptom occurs TCS function that puts the highest
priority to obtain the optimum traction
(stability).
TCS may operate momentarily, while driving on a road where friction coefficient varies, or
when downshifting or fully depressing accelerator pedal
ABS warning lamp and VDC warning lamp may turn ON, when the vehicle is on a rotating
turntable or is given a strong shaking or large vibrations on a ship while the engine is run-
ning.
In this case, restart the engine on a nor-
mal road. If the normal condition is re-
stored, there is no malfunction. In that
case, erase self-diagnosis result memory
for “ABS” with CONSULT-III.
VDC warning lamp may turn ON and VDC function, TCS function, hill start assist function
and brake limited slip differential (BLSD) function may not normally operate, when driving
on a special road the is extremely slanted (bank in a circuit course).
A malfunction in yaw rate/side/decel G sensor system may be detected when the vehicle
sharply turns during a spin turn, acceleration turn or drift driving while VDC function and
TCS function are OFF (VDC OFF switch is pressed and VDC OFF indicator lamp is in ON
status).
The vehicle speed does not increase, when the accelerator pedal is depressed while the
vehicle is on a 2-wheel chassis dynamometer for speedometer check.
This is not malfunction. (When checking
the vehicle on a chassis dynamometer,
operate VDC OFF switch so that TCS
function is OFF.)
The VDC warning lamp, ABS warn ing lamp and brake warning lamp turn ON and DTC
“C118E” may be detected in self-diagnosis resu lt of “ABS” when the brake pedal is exces-
sively operated, such as air bleeding. This is not a system malfunction because
this occurs due to the temporary de-
crease in accumulator fluid pressure. The
system returns to no
rmal condition when
the accumulator fluid pressure reaches
the specified pressure with the ignition
switch ON and the VDC warning lamp,
ABS warning lamp, a nd brake warning
lamp turn OFF. After these steps, ABS
self-diagnosis results are erased.
VDC OFF indicator lamp turns ON and TCS function is not operate when 4WD mode is “4L”.
(Models with 4WD system) This is not a malfunction. When the 4WD
mode becomes “4L” state, the TCS func-
tion is disabled. This function is enabled
when the 4WD mode becomes “AUTO”
or “4H”.
Revision: 2010 May2011 QX56

BRC-142
< SYSTEM DESCRIPTION >[BRAKE ASSIST (WITH PREVIEW FUNCTION)]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts LocationINFOID:0000000006248456
1. ICC steering switch 2. Information display, ICC system
warning lamp, IBA OFF indicator
lamp, buzzer
(On the combination meter)3. BCM
Refer to BCS-4, "
BODY CONTROL
SYSTEM : Component Parts Loca-
tion"
4. Transfer control unit
Refer to DLN-10, "
Component Parts
Location"
5. ICC brake hold relay 6. ECM
Refer to EC-16, "
Component Parts
Location"
7. ICC sensor 8. TCM
Refer to TM-10, "
A/T CONTROL
SYSTEM : Component Parts Loca-
tion"
9. ABS actuator and el ectric unit (con-
trol unit)
Refer to BRC-10, "
Component Parts
Location"
10. Stop lamp switch 11. ICC brake switch 12. IBA OFF switch
JSOIA0362ZZ
Revision: 2010 May2011 QX56