ISUZU AXIOM 2002 Service Repair Manual

6E±74
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS

P1275, P1639, P1271, P1273

P1285, P1272, P1273

P0336, P0337

P1220, P1515, P1221, P1515, P1516

P1280, P1271, P1272
Check for the following conditions:

Poor connection at PCM. Inspect the harness
connectors for backed±out terminals, improper
mating, broken locks, improperly formed or damage
terminals, and a poor terminal±to±wire connection.
Damaged harness. Inspect the wiring harness for
damage. If the harness is not damaged, observe an
affected sensor fs displayed value on the Tech 2 with
the ignition ªONº and the engine ªOFFº while you
move the connectors and the wiring harnesses
related to the following sensors:

Vapor Pressure (Fuel Tank Pressure) Sensor

MAP Sensor

EGR

TPS1/TPS2

APS1/APS2/APS3

CKP
Multiple PCM Information Sensor DTCs Set

StepActionValue(s)Ye sNo
1Was the ªOn-Board (OBD) System Checkº performed?
ÐGo to Step 2
Go to OBD
System
Check
21. Turn the ignition ªOFFº, disconnect the PCM.
2. Turn the ignition ªONº, check the 5 volt reference 1
and 2 circuit for the following conditions:

A poor connection at the PCM.

An open between the PCM connector and the
splice.

A short to ground.

A short to voltage.
Is there an open or short?
ÐGo to Step 3Go to Step 4
3Repair the open or short.
Is the action complete?
ÐVerify repairÐ
4Check the sensor ground circuit for the following
conditions:

A poor connection at the PCM or the affected
sensors.

An open between the PCM connector and the
affected sensors.
Is there an open or a poor connection?
ÐGo to Step 5Go to Step 6
5Repair the open or the poor connection.
Is the action complete?
ÐVerify repairÐ
6Following below the DTCs stored:
P1635, P1639
Ð
Go to
applicable
DTC table
Go to Step 7
7 Measure the resistance below the items:

Between EGR sensor supply circuit and Vapor
Pressure Sensor supply circuit.

Between MAP sensor supply circuit and Vapor
Pressure Sensor supply circuit.

Between Vapor Pressure Sensor supply circuit
and PCM harness connector. (5Volt supply
circuit)
Is the resistance near the specified value?
ÐGo to Step 9Go to Step 8

6E±75
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Multiple PCM Information Sensor DTCs Set

 
StepNo Ye s Value(s) Action
8Locate and repair the open circuit in the MAP or EGR or
Vapor Pressure sensor supply circuit.
Is the action complete?
ÐVerify repairÐ
91. Disconnect the MAP, Vapor pressure sensor and
EGR connector.
2. Ignition ªONº.
3. Measure the resistance of the blow areas:

MAP sensor GND circuit.

EGR GND circuit.

Vapor pressure sensor GND circuit.
Does the voltage resistance near the specified value?
ÐGo to Step 11Go to Step 10
10Locate and repair the short circuit in the MAP or EGR or
Vapor Pressure sensor signal or GND circuit.
Is the action complete?
ÐVerify repairÐ
11 Measure the resistance of the blow areas:

Between CKP Sensor supply circuit and PCM
harness connector. (5Volt supply circuit)
Does the voltage resistance near the specified value?
ÐGo to Step 13Go to Step 12
12Locate and repair the open circuit in the CKP or CMP
sensor supply circuit.
Is the action complete?
ÐVerify repairÐ
131. Disconnect the CKP sensor connector.
2. Ignition ªONº.
3. Measure the voltage of the blow areas:

CKP sensor GND circuit and shield circuit.
Does the voltage resistance near the specified value?
ÐGo to Step 15Go to Step 14
14Locate and repair the short circuit in the CKP sensor
signal or GND circuit.
Is the action complete?
ÐVerify repairÐ
15Are more of the following items for DTCs stored? EGR,
Vapor Pressure Sensor, MAP, CKP, TPS, APS
Ð
Go to
applicable
DTC table
Go to Step 16
16Replace the PCM.
The replacement PCM must be programmed.
Refer to
ON-Vehicle Service in Power Control Module
and Sensors for procedures.
And also refer to latest Service Bulletin. Check to see
if the latest software is released or not. And then Down
Load the LATEST PROGRAMMED SOFTWARE to the
replacement PCM.
Is the action complete?
Ð
Go to OBD
System
Check
Ð

6E±76
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Exhaust Gas Recirculation (EGR)
Diagnosis
An EGR flow check diagnosis of the linear EGR system is
covered by DTC P0401. Pintle position error diagnosis is
covered by DTC P0402, P0404, P1404, P0405, P0406. If
EGR diagnostic trouble codes P0401 and/or P0402,
P0404, P1404, P0405, P0406 are encountered, refer to
the DTC charts.
Engine Tech 2 Data Definitions and
Ranges
A/C CLUTCH ± Tech 2 Displays ON or OFF ±
Indicates whether the PCM has commanded the A/C
clutch ON. Used in A/C system diagnostic.
A/C REQUEST Ð Tech 2 Displays YES or NO Ð
Indicates the state of the A/C request input circuit from the
HVAC controls. The PCM uses the A/C request signal to
determine whether A/C compressor operation is being
requested.
AIR/FUEL RATIO Ð Tech 2 Range 0.0-25.5 Ð
Air/fuel ratio indicates the PCM commanded value. In
closed loop, the air/fuel ratio should normally be
displayed around ª14.2-14.7º. A lower air/fuel ratio
indicates a richer commanded mixture, which may be
seen during power enrichment or TWC protection modes.
A higher air/fuel ratio indicates a leaner commanded
mixture. This can be seen during deceleration fuel mode.
AP1 ÐTech 2 Range 0%-100% Ð
AP (accelerator pedal) angle is computed by the PCM
from the AP sensor voltage. AP angle should display
ª13%º at idle and ª85-89%º at wide open throttle.
AP2 ÐTech 2 Range 0%-100% Ð
AP (accelerator pedal) angle is computed by the PCM
from the AP sensor voltage. AP angle should display
ª85-89%º at idle and ª11-15%º at wide open throttle.
AP3 ÐTech 2 Range 0%-100% Ð
AP (accelerator pedal) angle is computed by the PCM
from the AP sensor voltage. AP angle should display
ª85-89%º at idle and ª32-36%º at wide open throttle.
BAROMETRIC PRESSURE Ð Tech 2 Range 10-105
kPa/0.00-5.00 Volts Ð
The barometric pressure reading is determined from the
MAP sensor signal monitored during key up and wide
open throttle (WOT) conditions. The barometric pressure
is used to compensate for altitude differences and is
normally displayed around ª61-104º depending on
altitude and barometric pressure.
CHECK TRANS LAMP Ð AUTO TRANSMISSION Ð
Indicates the need to check for a DTC with the Tech 2
when the lamp is flashing 0.2 seconds ON and 0.2
seconds OFF.
DESIRED EGR POS. Ð Tech 2 Range 0%-100% Ð
Represents the EGR pintle position that the PCM is
commanding.
DESIRED IDLE Ð Tech 2 Range 0-3187 RPM Ð
The idle speed that the PCM is commanding. The PCM
will compensate for various engine loads based on engine
coolant temperature, to keep the engine at the desired
speed.ECT Ð (Engine Coolant Temperature) Tech 2
Range ±40
C to 151
C (±40
F to 304
F) Ð
The engine coolant temperature (ECT) is mounted in the
coolant stream and sends engine temperature
information to the PCM. The PCM applies 5 volts to the
ECT sensor circuit. The sensor is a thermistor which
changes internal resistance as temperature changes.
When the sensor is cold (high resistance), the PCM
monitors a high signal voltage and interprets that as a cold
engine. As the sensor warms (decreasing resistance),
the voltage signal will decrease and the PCM will interpret
the lower voltage as a warm engine.
EGR DUTY CYCLE Ð Tech 2 Range 0%-100% Ð
Represents the EGR valve driver PWM signal from the
PCM. A duty cycle of 0% indicates that no EGR flow is
being commanded; a 100% duty cycle indicates
maximum EGR flow commanded.
EGR FEEDBACK Ð Tech 2 Range 0.00-5.00 Volts Ð
Indicates the EGR pintle position sensor signal voltage
being monitored by the PCM. A low voltage indicates a
fully extended pintle (closed valve); a voltage near 5 volts
indicates a retracted pintle (open valve).
ENGINE LOAD Ð Tech 2 Range 0%-100% Ð
Engine load is calculated by the PCM from engine speed
and MAF sensor readings. Engine load should increase
with an increase in RPM or air flow.
ENGINE RUN TIME Ð Tech 2 Range
00:00:00-99:99:99 Hrs:Min:Sec Ð
Indicates the time elapsed since the engine was started.
If the engine is stopped, engine run time will be reset to
00:00:00.
ENGINE SPEED Ð Range 0-9999 RPM Ð
Engine speed is computed by the PCM from the 58X
reference input. It should remain close to desired idle
under various engine loads with engine idling.
EVAP PURGE PWM Ð Tech 2 Range 0%-100% Ð
Represents the PCM commanded PWM duty cycle of the
EVAP purge solenoid valve. ª0%º displayed indicates no
purge; ª100%º displayed indicates full purge.
FUEL PUMP Ð Tech 2 Displays ON or OFF Ð
Indicates the PCM commanded state of the fuel pump
relay driver circuit.
HO2S BANK 1, SEN. 1
Ð Tech 2 Range 0-1132 mV Ð
Represents the fuel control exhaust oxygen sensor
output voltage. Should fluctuate constantly within a range
between 10 mV (lean exhaust) and 1000 mV (rich
exhaust) while operating in closed loop.
HO2S BANK 1, SEN. 2
Ð Tech 2 Range 0-1000mV Ð
Monitors the exhaust oxygen sensor output voltage. The
PCM monitors the operating efficiency of catalytic
converter by comparing the output voltages of sensor 1
and sensor 2 in this bank. If the catalytic converter is
operating efficiently, the output voltage of sensor 1 will
give a greater fluctuation than that of sensor 2. If the
PCM detects an abnormal level of voltage fluctuation
from sensor 2, a DTC P0420 will be set, indicating that the
catalytic converter for this bank is no longer operating
efficiently.

6E±77
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
HO2S BANK2, SEN. 1 ÐTech 2 Range 0-1132 mVÐ
Represents the fuel control exhaust oxygen sensor
output voltage. Should fluctuate constantly within a range
between 10mV (lean exhaust) and 1000 mV (rich
exhaust) while operating in closed loop.
HO2S BANK 2, SEN. 2ÐTech 2 Range 0-1000 mVÐ
Monitors the exhaust oxygen sensor output voltage. The
PCM monitors the operating efficiency of catalytic
converter by comparing the output voltages of sensor 1
and sensor 2 in this bank. If the catalytic converter is
operating efficiently, the output voltage of sensor 1 will
have a greater fluctuation than that of sensor 2. If the
PCM detects an abnormal level of voltage fluctuation
from sensor 2, a DTC P0430 will be set, indicating that the
catalytic converter for this bank is no longer operating
efficiently.
HO2S BANK 1, SEN. 1ÐTech 2 Displays NOT
READY or READYÐ
Indicates the status of the exhaust oxygen sensor. The
Tech 2 will indicate that the exhaust oxygen sensor is
ready when the PCM detects a fluctuating HO2S voltage
sufficient to allow closed loop operation. This will not
occur unless the exhaust oxygen sensor is warmed up.
HO2S BANK 2, SEN. 1 Ð Tech 2 Displays NOT
READY or READY Ð
Indicates the status of the exhaust oxygen sensor. The
Tech 2 will indicate that the exhaust oxygen sensor is
ready when the PCM detects a fluctuating HO2S voltage
sufficient to allow closed loop operation. This will not
occur unless the exhaust oxygen sensor is warmed up.
HO2S WARM UP TIME BANK 1, SEN. 1/BANK 1,
SEN 2/BANK 2 SEN. 1/BANK 2 SEN. 2 Ð Tech 2
Range 00:00:00-99:99:99 HRS:MIN:SEC Ð
Indicates warm-up time for each HO2S. The HO2S
warm-up time is used for the HO2S heater test. The PCM
will run the heater test only after a cold start (determined
by engine coolant and intake air temperature at the time
of start-up) and only once during an ignition cycle. When
the engine is started the PCM will monitor the HO2S
voltage. When the HO2S voltage indicates a sufficiently
active sensor, the PCM looks at how much time has
elapsed since start-up. If the PCM determines that tool
much time was required for the HO2S to become active,
a DTC will set. If the engine was warm when started,
HO2S warm-up will the display ª00:00:00º.
IAT (INTAKE AIR TEMPERATURE) Ð Tech 2 Range
±40
C to 151
C (±40
F to 304
F) Ð
The PCM converts the resistance of the intake air
temperature sensor to degrees. Intake air temperature
(IAT) is used by the PCM to adjust fuel delivery and spark
timing according to incoming air density.
IGNITION 1 Ð Tech 2 Range 0-25.5 Volts Ð
This represents the system voltage measured by the
PCM at its ignition feed.INJ. PULSE BANK 1/INJ. PULSE BANK 2 Ð Tech 2
Range 0-1000 msec. Ð
Indicates the amount of time the PCM is commanding
each injector ªONº during each engine cycle. A longer
injector pulse width will cause more fuel to be delivered.
Injector pulse width should increase with increased
engine load.
LONG TERM FUEL TRIM BANK 1/BANK 2 Ð
The long term fuel trim is derived from the short term fuel
trim values and represents a long term correction of fuel
delivery for the bank in question. A value of 0% indicates
that fuel delivery requires no compensation to maintain
the PCM commanded air/fuel ratio. A negative value
significantly below 0% indicates that the fuel system is
rich and fuel delivery is being reduced (decreased injector
pulse width). A positive value significantly greater than
0% indicates that a lean condition exists and the PCM is
compensating by adding fuel (increased injector pulse
width). Because long term fuel trim tends to follow short
term fuel trim, a value in the negative range due to
canister purge at idle should not be considered unusual.
Fuel trim values at maximum authority may indicate an
excessively rich or lean system.
Fuel System STATUS Ð Tech 2 Displays OPEN or
CLOSED Ð
ªCLOSEDº indicates that the PCM is controlling fuel
delivery according to oxygen sensor voltage. In ªOPENº
the PCM ignores the oxygen sensor voltage and bases
the amount of fuel to be delivered on TP sensor, engine
coolant, and MAF sensor inputs only.
MAF Ð Tech 2 Range 0.0-512 gm/s Ð
MAF (mass air flow) is the MAF input frequency
converted to grams of air per second. This indicates the
amount of air entering the engine.
MAP
Ð Tech 2 Range 10-105 kPa (0.00-4.97 Volts) Ð
The manifold absolute pressure (MAP) sensor measures
the change in the intake manifold pressure from engine
load, EGR flow, and speed changes. As intake manifold
pressure increases, intake vacuum decreases, resulting
in a higher MAP sensor voltage and kPa reading. The
MAP sensor signal is used to monitor intake manifold
pressure changes during the EGR flow test, to update the
BARO reading, and as an enabling factor for several of
the diagnostics.
MIL Ð Tech 2 Displays ON or OFF Ð
Indicates the PCM commanded state of the malfunction
indicator lamp.
MISFIRE CUR. CYL. #1 /#2 /#3 /#4 / #5 / #6 Ð Tech 2
Range 0-255 Counts Ð
The misfire current counters increase at a rate according
to the number of the possible misfires being detected on
each cylinder. The counters may normally display some
activity, but the activity should be nearly equal for all the
cylinders.

6E±78
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
MISFIRE CUR. CYL. #1 /#2 /#3 /#4 / #5 / #6 Ð Tech 2
Range 0-65535 Counts Ð
The misfire history counters display the relative level of
misfire that has been detected on each cylinder. The
misfire history counters will not update or show any
activity until a misfire DTC (P0300) has become active.
MISFIRE FAILURES SINCE FIRST FAIL Ð Tech 2
Range 0-65535 Counts Ð
Indicates the number of 200 crankshaft revolution sample
periods during which the level of misfire was sufficiently
high to report a fail.
MISFIRE PASSES SINCE FIRST FAIL Ð Tech 2
Range 0-65535 Counts Ð
Indicates the number of 200 crankshaft revolution sample
periods during which the level of misfire was sufficiently
low to report a pass.
POWER ENRICHMENT Ð Tech 2 Displays ACTIVE
or INACTIVE Ð
ªACTIVEº displayed indicates that the PCM has detected
conditions appropriate to operate in power enrichment
mode. The PCM will command power enrichment mode
when a large increase in throttle position and load is
detected. While in power enrichment mode, the PCM will
increase the amount of fuel delivered by entering open
loop and increasing the injector pulse width. This is done
to prevent a possible sag or hesitation from occurring
during acceleration.
SPARK Ð Tech 2 Range ±64
to 64
Ð
Displays the amount of spark advance being commanded
by the PCM on the IC circuit.
START-UP ECT Ð Tech 2 Range ±40
C to 151
C
(±40
F to 304
F) Ð
Indicates the engine coolant temperature at the time that
the vehicle was started. Used by the HO2S diagnostic to
determine if the last start-up was a cold start.
START-UP IAT Ð Tech 2 Range ±40
C to 151
C
(±40
F to 304
F) Ð
Indicates the intake air temperature at the time that the
vehicle was started. Used by the HO2S diagnostic to
determine if the last start-up was a cold start.
TOTAL MISFIRE CURRENT COUNT Ð Tech 2
Range 0-255 Ð
Indicates the total number of cylinder firing events that
were detected as being misfires during the last 200
crankshaft revolution sample period.
TP Ð Tech 2 Range 0%-100% Ð
TP (throttle position) angle is computed by the PCM from
the TP sensor voltage. TP angle should display ª3-5%º
at idle and ª100%º at wide open throttle.
CATALYST PROTECTION MODE Ð Tech 2 Displays
YES or NO Ð
ªYESº displayed indicates that the PCM has detected
conditions appropriate to operate in TWC protection
mode. The PCM will decrease the air/fuel ratio to a value
that depends on mass air flow (higher mass air flow =
lower air/fuel ratio).UPSHIFT LAMP (MANUAL TRANSMISSION)
VEHICLE SPEED Ð Tech 2 Range 0-255 km/h
(0-155 mph) Ð
The vehicle speed sensor signal is converted into km/h
and mph for display.
WEAK CYLINDER Ð Tech 2 Displays Cylinder
Number Ð
This indicates that the PCM has detected crankshaft
speed variations that indicate 2% or more cylinder firing
events are misfires.
Typical Scan Data Values
Use the Typical Scan Data Values Table only after the
On-Board Diagnostic System Check has been
completed, no DTC(s) were noted, and you have
determined that the on-board diagnostics are functioning
properly. Tech 2 values from a properly-running engine
may be used for comparison with the engine you are
diagnosing. The typical scan data values represent
values that would be seen on a normally-running engine.
NOTE: A Tech 2 that displays faulty data should not be
used, and the problem should be reported to the Tech 2
manufacturer. Use of a faulty Tech 2 can result in
misdiagnosis and unnecessary replacement of parts.
Only the parameters listed below are referred to in this
service manual for use in diagnosis. For further
information on using the Tech 2 to diagnose the PCM and
related sensors, refer to the applicable reference section
listed below. If all values are within the typical range
described below, refer to the
Symptoms section for
diagnosis.
Test Conditions
Engine running, lower radiator hose hot, transmission in
park or neutral, closed loop, accessories off, brake not
applied and air conditioning off.

6E±79
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
3.5L V-6 Engine (Automatic and Manual Transmission)
Tech 2
Parameter
Data ListUnits DisplayedTypical Data
Values (IDLE)Typical Data
Values
(2500 RPM)Refer To
A/C Clutch
RelayEngineOn/OffOffOffGeneral Description and
Operation, A/C Clutch
Circuit Operation
A/C RequestEngineYes/NoNoNoGeneral Description and
Operation, A/C Request
Signal
Air/Fuel RatioEngineRatio: _ to 114.714.7General Description and
Operation, Fuel System
Metering Purpose
APP Sensor1EnginePercent11±1335±40General Description and
Operation
APP Sensor2EnginePercent87±8860±65General Description and
Operation
APP Sensor3EnginePercent87±8850±57General Description and
Operation
Barometric
PressureEnginekPa61-104
(depends on
altitude and
barometric
pressure)61-104
(depends on
altitude and
barometric
pressure)General Description and
Operation
Brake Light
SwitchEngineOpen 0V/Closed
12VOpen 0VOpen 0VRefer to Section 5
Check Trans
Lamp (Auto
Trans)EngineOn/OffOffOff4L30-E Automatic
Transmission Diagnosis
Cruise Main
SwitchEngineActive/InactiveInactiveInactiveRefer to Section 10
Cruise Set
SwitchEngineActive/InactiveInactiveInactiveRefer to Section 10
Cruise Cancel
SwitchEngineActive/InactiveInactiveInactiveRefer to Section 10
Cruise
Resume
SwitchEngineActive/InactiveInactiveInactiveRefer to Section 10
Decel Fuel
CutoffEngineActive/InactiveInactiveInactiveGeneral Description and
Operation, Deceleration
Mode
Desired EGR
PositionEnginePercent0%0%General Description and
Operation, EGR Pintle
Position Sensor
Desired Idle
SpeedEngineRPM750800General Description and
Operation
ECT (Engine
Coolant Temp)EngineDegrees C,
Degrees F80-100
C
(176-212
F)80-100
C
(176-212
F)General Description and
Operation, Engine
Coolant Temperature
(ECT) Sensor
EGR Closed
Pintle PositionEngineSteps20-4020-40General Description and
Operation, EGR Pintle
Position Sensor

6E±80
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Tech 2
ParameterRefer To Typical Data
Values
(2500 RPM) Typical Data
Values (IDLE) Units Displayed Data List
EGR Duty
CycleEnginePercent0%0%General Description and
Operation, Linear EGR
Operation and Results of
Incorrect Operation
EGR
FeedbackEngineVolts0.45-0.800.45-0.80Ð
EGR
NormalizedEnginePercent0%0%Ð
Engine LoadEnginePercent2.0% - 5.5%8.0% - 16.0%General Description and
Operation, Mass Air Flow
(MAF) Sensor
Time From
StartEngineSecVaries. Resets
at each engine
start.Varies. Resets
at each engine
start.
Ð
Engine SpeedEngineRPMWithin ±50 to
+100 of
ªDesired IdleºActual engine
speed
Ð
EVAP Purge
SolenoidEnginePercent0%0%Diagnosis, EVAP
Emission Canister Purge
Valve Check
EVAP Vent
ValveEngineOn/OffOffOffDiagnosis, EVAP Canister
Purge Solenoid and
EVAP Vacuum Switch
and Visual Check; DTCs:
P1441, P1442
Fuel System
StatusEngineOpen
Loop/Closed
LoopClosed LoopClosed LoopGeneral Description
Fuel LevelEnginePercentÐÐEngine Fuel
Fuel Level
SensorEngineVoltsÐÐEngine Fuel
Fuel Tank
(Vapor)EngineVolts1.02 ± 1.861.02 ± 2.57General Description and
Operation
Pressure
Sensorin. H2OÐÐ
Fuel PumpEngineOn/OffOnOnEngine Fuel
HO2S Bank 1
Sen.1
(millivolts)O2
Sensor
DataMillivolts50-950
changing
quickly50-950, always
changing
quicklyGeneral Description and
Operation, Fuel control
HO2S
HO2S Bank 1
Sen.2
(millivolts)
(Auto Trans)O2
Sensor
DataMillivolts200-700
changing slowly250-650
changing slowlyGeneral Description and
Operation, Fuel Metering
System
HO2S Bank 1
Sen.2
(millivolts)
(Manual
Trans)O2
Sensor
DataMillivolts50-950
changing
quickly50-950
changing
quicklyGeneral Description and
Operation, Fuel Metering
System
HO2S Bank 1
Sen.3
(millivolts)
(Manual
Trans)O2
Sensor
DataMillivolts200-700
changing slowly250-650
changing slowlyGeneral Description and
Operation, Catalyst
Monitor Heated Oxygen
Sensor (Manual Trans)

6E±81
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Tech 2
ParameterRefer To Typical Data
Values
(2500 RPM) Typical Data
Values (IDLE) Units Displayed Data List
HO2S Bank 2
Sen.1
(millivolts)O2
Sensor
DataMillivolts50-950
changing
quickly50-950
changing
quicklyGeneral Description and
Operation, Fuel Control
HO2S
HO2S Bank 2
Sen.2
(millivolts)
(Auto trans)O2
Sensor
DataMillivolts200-700
changing slowly250-650
changing slowlyGeneral Description and
Operation, Fuel Metering
System
HO2S Bank 1
Sen.1
(ready/not
ready)O2
Sensor
DataReady
Yes/NoReady
Ye sReady
Ye sGeneral Description and
Operation, Fuel Control
HO2S; DTC: P0135
HO2S Bank 2
Sen.1
(ready/not
ready)O2
Sensor
DataReady
Yes/NoReady
Ye sReady
Ye sGeneral Description and
Operation, Fuel Control
HO2S
HO2S
Warm-Up Time
Bank 1 Sen.1O2
Sensor
DataSeconds25-4525-45General Description and
Operation, Fuel Control
HO2S
HO2S
Warm-Up Time
Bank 1 Sen.2O2
Sensor
DataSeconds60-10060-100General Description and
Operation, Fuel Control
HO2S
HO2S
Warm-Up Time
Bank 2 Sen.1O2
Sensor
DataSeconds25-4525-45General Description and
Operation, Fuel Control
HO2S
HO2S
Warm-Up Time
Bank 2 Sen.2O2
Sensor
DataSeconds60-10060-100General Description and
Operation, Catalyst
Monitor Heated Oxygen
Sensor (Auto Trans)
IAT (Intake Air
Temp)EngineDegrees C,
Degrees F0-100
C,
depends on
underhood
temperature0-80
C,
depends on
underhood
temperatureGeneral Description and
Operation, Intake Air
Temperature (IAT) Sensor
Illumination
SwitchEngineClosed 0V/Open
12VClosed 0VClosed 0VRefer to Section 8
Ignition
VoltageEngineVolts12.8-14.112.8-14.1General Description and
Operation, Electronic
Ignition System
Inj. Pulse Bank
1EngineMilliseconds2.0-4.02.5-4.0General Description, Fuel
Metering, Fuel Injector
Inj. Pulse Bank
2EngineMilliseconds2.0-4.02.5-4.0General Description, Fuel
Metering, Fuel Injector
Knock PresentEngineNo/YesNoNoGeneral Description and
ION Sensing Module
Knock SignalEnginePercent1~41~4General Description and
ION Sensing Module
Knock Sensor
RetardEngine
CA00General Description and
ION Sensing Module
Knock CounterEngineCountsÐÐGeneral Description
Long Term FT
Bank 1 (Long
Term Fuel
Trim)MisfireCounts and
Percentage100 to 150
counts, ±22%
to +17%100 to 150
counts, ±22%
to +17%Diagnosis, Fuel Trim
System Monitor; DTCs:
P0171, P0172

6E±82
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Tech 2
ParameterRefer To Typical Data
Values
(2500 RPM) Typical Data
Values (IDLE) Units Displayed Data List
Long Term FT
Bank 2 (Long
Term Fuel
Trim)MisfireCounts and
Percentage100 to 150
counts, ±22%
to +17%100 to 150
counts, ±22%
to +17%Diagnosis, Fuel Trim
System Monitor; DTCs:
P0171
MAF (Mass Air
Flow)EngineGrams per
second2.85-6.659.5-16.5General Description and
Operation, MAF; DTCs:
P101, P0102, P0103
MAP kPa
(Manifold
Absolute
EngineKilopascals23-4019-32General Description and
Operation, Manifold
Absolute Pressure (MAP)Absolute
Pressure)Volts0.65-1.320.46-1.10Absolute Pressure (MAP)
Sensor; DTCs: P0106,
P0107, P0108
MILEngineOn/OffOffOffOn-Board Diagnostic
System Check
Misfire Cur. Cyl
#1MisfireCounts0-20-2DTC P0300
Misfire Cur. Cyl
#2MisfireCounts0-20-2DTC P0300
Misfire Cur. Cyl
#3MisfireCounts0-20-2DTC P0300
Misfire Cur. Cyl
#4MisfireCounts0-20-2DTC P0300
Misfire Cur. Cyl
#5MisfireCounts0-20-2DTC P0300
Misfire Cur. Cyl
#6MisfireCounts0-20-2DTC P0300
Misfire Hist.
Cyl #1MisfireCounts00DTC P0300
Misfire Hist.
Cyl #2MisfireCounts00DTC P0300
Misfire Hist.
Cyl #3MisfireCounts00DTC P0300
Misfire Hist.
Cyl #4MisfireCounts00DTC P0300
Misfire Hist.
Cyl #5MisfireCounts00DTC P0300
Misfire Hist.
Cyl #6MisfireCounts00DTC P0300
Misfire Failures
Since First FailMisfireCounts00DTC P0300
Misfire Passes
Since First FailMisfireCounts00DTC P0300
PNP
(Park/Neutral
Position)EngineP-N /
R-D-3-2-LP-NP-N4L30-E Automatic
Transmission Diagnosis
Power
EnrichmentEngineNO/YESNONOGeneral Description and
Operation, Acceleration
Mode
PSP Switch
(Power
Steering
Pressure)EngineNormal/HiNormal
PressureNormal
PressureRefer to 2A Section

6E±83
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Tech 2
ParameterRefer To Typical Data
Values
(2500 RPM) Typical Data
Values (IDLE) Units Displayed Data List
Spark
(Advance)EngineDegrees Before
Top Dead Center15-2234-44General Description and
Operation, Electronic
Ignition System
Start-Up ECT
(Engine
Coolant Temp)EngineDegrees C,
Degrees FDepends on
engine coolant
temperature at
time of start-upDepends on
engine coolant
temperature at
time of start-upGeneral Description and
Operation, Engine
Coolant Temperature
(ECT) Sensor
Start-Up IAT
(Intake Air
Temp)EngineDegrees C,
Degrees FDepends on
intake air
temperature at
time of start-upDepends on
intake air
temperature at
time of start-upGeneral Description and
Operation, Intake Air
Temperature (IAT) Sensor
TCC Cruise
Brake SwitchEngineActive/InactiveActiveActiveRefer to Section 10
Total Misfire
Current CountMisfireCounts0-50-5DTC P0300
TP Sensor 1
(Throttle
Position
Sensor 1)EnginePercentage8±1228±36General Description and
Operation, Throttle
Position (TP) Sensor
TP Sensor 2
(Throttle
Position
Sensor 2)EnginePercentage8±1228±36General Description and
Operation, Throttle
Position (TP) Sensor
Throttle at IdleEngineNo/YesYe sNoGeneral Description and
Operation, Throttle
Position (TP) Sensor
Upshift Lamp
(manual trans)EngineOn/OffOffOffManual Transmission
Vehicle SpeedEngineMPH / km/h004L30-E Automatic
Transmission Diagnosis
Weak CylinderMisfireCylinder #ÐÐDTC P0300