ISUZU AXIOM 2002 Service Repair Manual

5A±42BRAKE CONTROL SYSTEM
Chart B-8 2WD Controller in 4WD Vehicle Controller (DTC 13 (Flash out) / C0285 (Serial
communications)), 4WD State Input Signal Failure (DTC 24 (Flash out) / C0282 (Serial
communications))
StepActionYe sNo
1Remove coil integrated module connector.
Is the coil integrated module connector (C-6) terminal 8 line
normally?
Go to Step 2
Repair.
Go to
Step 3
2Is the TOD control unit normally?
Replace EHCU.
Go to
Step 3
Replace TOD
control unit.
Go to
Step 3
31. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 3
Chart B-9 Pump Motor Failure (DTC 32 (Flash out) / C0267, C0268 (Serial
communications))
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Measure the voltage between terminal 1 of the coil integrated
module connector (C-5) and body ground.
Is the voltage equal to the battery voltage?
Go to Step 2
Repair
fuse/harness
between battery
and coil
integrated
module connector
(C-5) terminal 1.
Go to
Step 5
2Is the harness from the hydraulic unit connected to the coil
integrated module connector?
Go to Step 3
Connect to the
connector.
Go to
Step 3
3Is the hydraulic unit harness in good condition?
Go to Step 4
Replace EHCU.
Go to
Step 5
4Is the resistance of hydraulic unit connector terminals 1 and 2
between 0.2 and 1.0 ohms?Replace EHCU.
Go to
Step 5
Replace EHCU.
Go to
Step 5
51. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 5

5A±43
BRAKE CONTROL SYSTEM
Chart B-10 EHCU Valve Relay Failure (DTC 35 (Flash out) / C0265, C0266 (Serial
communications))
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Measure the voltage between terminal 1 of the coil integrated
module connector (C-5) and body ground.
Is the voltage equal to the battery voltage?
Replace EHCU.
Go to
Step 2
Repair fuse and
harness between
coil integrated
module connector
(C-5) terminal 1
and battery.
Go to
Step 2
21. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 2
Chart B-11 FL Isolation Solenoid Coil Failure (DTC 41 (Flash out) / C0245, C0247 (Serial
communications))
StepActionYe sNo
1Was the ªEHCU Connector Pin±out Checksº performed?
Go to Step 2
Go to ªEHCU
Connector
Pin±out Checks.º
21. Turn the key switch to off.
2. Disconnect the 2±way EHCU connector (C±5) from the
EHCU.
3. Inspect the connector for damage or corrosion.
Is the connector free from damage or corrosion?
Go to Step 3
Repair the
connector.
Repeat the ªBasic
Diagnostic Flow
Chart.º
31. Replace the Coil Integrated Module.
2. Reconnect all components, ensure all components are
properly mounted.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 3
Chart B-12 FL Dump Solenoid Coil Failure (DTC 42 (Flash out) / C0246, C0248 (Serial
communications))
StepActionYe sNo
1Was the ªEHCU Connector Pin±out Checksº performed?
Go to Step 2
Go to ªEHCU
Connector
Pin±out Checks.º
21. Turn the key switch to off.
2. Disconnect the 2±way EHCU connector (C±5) from the
EHCU.
3. Inspect the connector for damage or corrosion.
Is the connector free from damage or corrosion?
Go to Step 3
Repair the
connector.
Repeat the ªBasic
Diagnostic Flow
Chart.º
31. Replace the Coil Integrated Module.
2. Reconnect all components, ensure all components are
properly mounted.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 3

5A±44BRAKE CONTROL SYSTEM
Chart B-13 FR Isolation Solenoid Coil Failure (DTC 43 (Flash out) / C0241, C0243 (Serial
communications))
StepActionYe sNo
1Was the ªEHCU Connector Pin±out Checksº performed?
Go to Step 2
Go to ªEHCU
Connector
Pin±out Checks.º
21. Turn the key switch to off.
2. Disconnect the 2±way EHCU connector (C±5) from the
EHCU.
3. Inspect the connector for damage or corrosion.
Is the connector free from damage or corrosion?
Go to Step 3
Repair the
connector.
Repeat the ªBasic
Diagnostic Flow
Chart.º
31. Replace the Coil Integrated Module.
2. Reconnect all components, ensure all components are
properly mounted.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 3
Chart B-14 FR Dump Solenoid Coil Failure (DTC 44(Flash out) / C0242, C0244 (Serial
communications))
StepActionYe sNo
1Was the ªEHCU Connector Pin±out Checksº performed?
Go to Step 2
Go to ªEHCU
Connector
Pin±out Checks.º
21. Turn the key switch to off.
2. Disconnect the 2±way EHCU connector (C±5) from the
EHCU.
3. Inspect the connector for damage or corrosion.
Is the connector free from damage or corrosion?
Go to Step 3
Repair the
connector.
Repeat the ªBasic
Diagnostic Flow
Chart.º
31. Replace the Coil Integrated Module.
2. Reconnect all components, ensure all components are
properly mounted.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 3
Chart B-15 Rear Isolation Solenoid Coil Failure (DTC 45 (Flash out) / C0251, C0253 (Serial
communications))
StepActionYe sNo
1Was the ªEHCU Connector Pin±out Checksº performed?
Go to Step 2
Go to ªEHCU
Connector
Pin±out Checks.º
21. Turn the key switch to off.
2. Disconnect the 2±way EHCU connector (C±5) from the
EHCU.
3. Inspect the connector for damage or corrosion.
Is the connector free from damage or corrosion?
Go to Step 3
Repair the
connector.
Repeat the ªBasic
Diagnostic Flow
Chart.º
31. Replace the Coil Integrated Module.
2. Reconnect all components, ensure all components are
properly mounted.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 3

5A±45
BRAKE CONTROL SYSTEM
Chart B-16 Rear Dump Solenoid Coil Failure (DTC 46 (Flash out) / C0252, C0254 (Serial
communications))
StepActionYe sNo
1Was the ªEHCU Connector Pin±out Checksº performed?
Go to Step 2
Go to ªEHCU
Connector
Pin±out Checks.º
21. Turn the key switch to off.
2. Disconnect the 2±way EHCU connector (C±5) from the
EHCU.
3. Inspect the connector for damage or corrosion.
Is the connector free from damage or corrosion?
Go to Step 3
Repair the
connector.
Repeat the ªBasic
Diagnostic Flow
Chart.º
31. Replace the Coil Integrated Module.
2. Reconnect all components, ensure all components are
properly mounted.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 3
Chart B-17 FL Speed Sensor Open or Shorted (DTC 51 (Flash out) / C0225 (Serial
communications))
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Measure the resistance between coil integrated module
connector (C-6) terminals 2 and 10.
Is the resistance between 2.0k and 2.8k ohms?Check for faults
in harness
between speed
sensor and coil
integrated
module.
Fault found:
Repair, and
perform system
self-check.
No fault found:
Replace coil
integrated
module.
Go to
Step 3Go to Step 2
2Measure the FL speed sensor resistance at the sensor connector.
Is the resistance between 2.0k and 2.8k ohms?Repair harness
abnormality
between sensors
and coil
integrated
module.
Go to
Step 3
Replace sensor.
Go to
Step 3
31. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 3

5A±46BRAKE CONTROL SYSTEM
Chart B-18 FR Speed Sensor Open or Shorted (DTC 52 (Flash out) / C0221 (Serial
communications))
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Measure the resistance between coil integrated module
connector (C-6) terminals 3 and 11.
Is the resistance between 2.0k and 2.8k ohms?Check for faults
in harness
between speed
sensor and coil
integrated
module.
Fault found:
Repair, and
perform system
self-check.
No fault found:
Replace coil
integrated
module.
Go to
Step 3Go to Step 2
2Measure the FR speed sensor resistance at the sensor
connector.
Is the resistance between 2.0k and 2.8k ohms?Repair harness
abnormality
between sensors
and coil
integrated
module.
Go to
Step 3
Replace sensor.
Go to
Step 3
31. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 3

5A±47
BRAKE CONTROL SYSTEM
Chart B-19 Rear Speed Sensor Open or Shorted (DTC 53 (Flash out) / C0235 (Serial
communications))
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Measure the resistance between coil integrated module
connector (C-6) terminals 4 and 12.
Is the resistance between 1.0k and 1.7k ohms?Check for faults
in harness
between speed
sensor and coil
integrated
module.
Fault found:
Repair, and
perform system
self-check.
No fault found:
Replace EHCU.
Go to
Step 3Go to Step 2
2Measure the Rear speed sensor resistance at the sensor
connector.
Is the resistance between 1.0k and 1.7k ohms?Repair harness
abnormality
between sensors
and coil
integrated
module.
Go to
Step 3
Replace sensor.
Go to
Step 3
31. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 3

5A±48BRAKE CONTROL SYSTEM
Chart B-20 FL Speed Sensor Missing Signal (DTC 61 (Flash out) / C0226, C0227 (Serial
communications))
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Measure the FL speed sensor resistance between coil
integrated module connector (C-6) terminals 2 and 10.
Is the resistance between 2.0k and 2.8k ohms?
Go to Step 2Go to Step 3
2Is there play sensor/sensor rotor?Repair.
Go to
Step 6Go to Step 4
3Measure the FL speed sensor resistance at the sensor connector.
Is the resistance between 2.0k and 2.8k ohms?Repair harness
abnormality
between sensors
and coil
integrated
module.
Go to
Step 6
Replace sensor.
Go to
Step 6
4Damage and powdered iron sticking to sensor/sensor ring?Repair.
Go to
Step 6Go to Step 5
5Is sensor output normal? (Chart C-1-1 or TC-1)Check for faults
in harness
between speed
sensor and coil
integrated
module.
Fault found:
repair, and
perform system
self-check.
No fault found:
replace EHCU.
Go to
Step 6
Replace sensor.
Go to
Step 6
61. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 6
NOTE: Even after repairing the faulty part the warning
light (W/L) does not go out if the vehicle is at a stop. Turn
the ignition switch to the ON position and drive the vehicle
at 12 km/h (8 mph) or higher to make sure that the
warning light goes out.

5A±49
BRAKE CONTROL SYSTEM
Chart B-21 FR Speed Sensor Missing Signal (DTC 62 (Flash out) / C0222, C0223 (Serial
communications))
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Measure the FR speed sensor resistance between coil
integrated module connector (C-6) terminals 3 and 11.
Is the resistance between 2.0k and 2.8k ohms?
Go to Step 2Go to Step 3
2Is there play sensor/sensor rotor?Repair.
Go to
Step 6Go to Step 4
3Measure the FR speed sensor resistance at the sensor
connector.
Is the resistance between 2.0k and 2.8k ohms?Repair harness
abnormality
between sensors
and coil
integrated
module.
Go to
Step 6
Replace sensor.
Go to
Step 6
4Damage and powered iron sticking to sensor/sensor ring?Repair.
Go to
Step 6Go to Step 5
5Is sensor output normal? (Chart C-1-2 or TC-1)Check for faults
in harness
between speed
sensor and coil
integrated
module.
Fault found:
repair, and
perform system
self-check.
No fault found:
replace EHCU.
Go to
Step 6
Replace sensor.
Go to
Step 6
61. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 6
NOTE: Even after repairing the faulty part the warning
light (W/L) does not go out if the vehicle is at a stop. Turn
the ignition switch to the ON position and drive the vehicle
at 12 km/h (8 mph) or higher to make sure that the
warning light goes out.

5A±50BRAKE CONTROL SYSTEM
Chart B-22 Rear Speed Sensor Missing Signal (DTC 63 (Flash out) / C0236, C0237 (Serial
communications))
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Measure the Rear speed sensor resistance between coil
integrated module connector (C-6) terminals 4 and 12.
Is the resistance between 1.0k and 1.7k ohms?
Go to Step 2Go to Step 3
2Is there play sensor/sensor rotor?Repair.
Go to
Step 6Go to Step 4
3Measure the rear speed sensor resistance at the sensor
connector.
Is the resistance between 1.0k and 1.7k ohms?Repair harness
abnormality
between sensors
and coil
integrated
module.
Go to
Step 6
Replace sensor.
Go to
Step 6
4Damage and powered iron sticking to sensor/sensor ring?Repair.
Go to
Step 6Go to Step 5
5Is sensor output normal? (Chart C-1-3 or TC-1)Check for faults
in harness
between speed
sensor and coil
integrated
module.
Fault found:
repair, and
perform system
self-check.
No fault found:
replace EHCU.
Go to
Step 6
Replace sensor.
Go to
Step 6
61. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 6
NOTE: Even after repairing the faulty part the warning
light (W/L) does not go out if the vehicle is at a stop. Turn
the ignition switch to the ON position and drive the vehicle
at 12 km/h (8 mph) or higher to make sure that the
warning light goes out.

5A±51
BRAKE CONTROL SYSTEM
Chart B-23 Simultaneous Drop-out of Front Speed Sensor Signal (DTC 64 (Flash out) /
C0229 (Serial communications))
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Measure the FL speed sensor resistance between coil
integrated module connector (C-6) terminals 2 and 10.
Is the resistance between 2.0k and 2.8k ohms?
Go to Step 2Go to Step 3
2Measure the FR speed sensor resistance between coil integrated
module connector (C-6) terminals 3 and 11.
Is the resistance between 2.0k and 2.8 k ohms?
Go to Step 5Go to Step 4
3Measure the FL speed sensor resistance at the sensor connector.
Is the resistance between 2.0k and 2.8k ohms?Repair harness
abnormality
between sensors
and coil
integrated
module.
Go to
Step 2
Replace sensor.
Go to
Step 2
4Measure the FR speed sensor resistance at the sensor
connector.
Is the resistance between 2.0k and 2.8k ohms?Repair harness
abnormality
between sensors
and coil
integrated
module.
Go to
Step 5
Replace sensor.
Go to
Step 5
5Damage and powered iron sticking to sensor/sensor ring?Repair.
Go to
Step 6Go to Step 6
6Is there play sensor/sensor rotor?Repair.
Go to
Step 7Go to Step 7
7Is sensor output normal? (Chart C-1-1&C-1-2 or TC-1)Check for faults
in harness
between speed
sensor and coil
integrated
module.
Fault found:
repair, and
perform system
self-check.
No fault found:
replace EHCU.
Go to
Step 8
Replace sensor.
Go to
Step 8
81. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
Repeat ªBasic
diagnostic flow
chartº
Go to Step 8
NOTE: Even after repairing the faulty part the warning
light (W/L) does not go out if the vehicle is at a stop. Turn
the ignition switch to the ON position and drive the vehicle
at 12 km/h (8 mph) or higher to make sure that the
warning light goes out.