torque ISUZU KB P190 2007 Workshop Owners Manual

3D-12 REAR SUSPENSION
Reassembly
1. Apply grease to both faces of each leaf spring at
reassembly.
2. Set the leaf springs, aligning them to the setting mark made
before disassembly.

F03L100006
3. Assemble the leaf springs using a bench press.
4. Apply grease to the outside of the bushing.
Install a new center bolt and tighten it to the specified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅ft)
29 (3.0/22)
5. Install the bushing using a bench press and a suitable metal fitting.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3D-14 REAR SUSPENSION

Removal
1. Remove the bolt and nut.
2. Take out the stabilizer bar assembly.
3. Remove the nut and take out the link from the stabilizer
bar.
4. Take out the cap and bush from the stabilizer bar.




Installation
1. Set the bush and cap on the stabilizer bar.
2. Install the link on the stabilizer bar and tighten the nut to the specified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅ft)
50 (5.1/37)

3. Install the stabilizer bar assembly on the rear axle and
tighten the bolt to the specified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅ft)
25 (2.5/18)

4. Set the stabilizer bar assembly to the frame bracket and
tighten the nut to the specified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅ft)
50 (5.1/37)



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

WHEELS AND TIRES 3E-1
SECTION 3E
WHEELS AND TIRES
TABLE OF CONTENTS
PAGE
Main Data and Specifications ........................................................................................... 3E- 2
Torque Specifications ....................................................................................................... 3E- 3
Special Parts Fixing Nuts and Bolts ........................................................................... 3E- 3
Wheels and Tires ............................................................................................................... 3E- 4
General Description...................................................................................................... 3E- 4
Servicing...................................................................................................................... .. 3E- 6
Disassembly and Reassembly..................................................................................... 3E- 7
Inspection and Repair .................................................................................................. 3E- 8
Troubleshooting ................................................................................................................ 3E- 10


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

WHEELS AND TIRES 3E-3
TORQUE SPECIFICATIONS
SPECIAL PARTS FIXING NUTS AND BOLTS
WHEELS AND TIRES
N⋅m (kgf ⋅m/lb ⋅ft)






RTW 73ELF000101



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3E-6 WHEELS AND TIRES
SERVICING
Servicing refers to general maintenance procedures to be performed by qualified service personnel.




WHEEL NUT TORQUES
W heel Nut Torque N⋅m (kgf ⋅m/lb ⋅ft)
117.7 ± 9.8 (12 ± 1.0 / 86.8 ± 7.2)





TIRE ROTATION
For of radial tires, interchange the front and the rear wheels on
the same side as shown in the figure.





If one-sided tire wear appears on radial tires, rotate the wheels
as shown in the figure.

Note:
After rotation, adjust the front and rear tire pressure and be sure to check wheel nut tightness.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

WHEELS AND TIRES 3E-9
Important Operations
1. Tire Assembly
To assemble, align the match mark (approx. 10mm diameter
paint mark) on the wheel with the match mark (approx. 8mm
diameter red paint mark) on the tire. If the match mark on the
wheel has disappeared, align with air valve instead.

2. Wheel and Tire Assembly





3. Wheel Nut
Tighten wheel nuts in numerical order.
W heel Nut Torque N⋅m (kgf ⋅m/lb ⋅ft)
117.7 ± 9.8 (12 ± 1.0 / 86.8 ± 7.2)



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

PROPELLER SHAFT 4A-1
Torque Specifications .................................................................................................. 4A- 8
Rear Propeller Shaft .......................................................................................................... 4 A- 9
General Description...................................................................................................... 4A- 9
Removal and Installation.............................................................................................. 4A- 12
Universal Joint Disassembly ....................................................................................... 4A- 13
Inspection and Repair ................................................................................................. 4A- 15
Universal Joint Reassembly ....................................................................................... 4A- 17
Rear Propeller Shaft Assembly ........................................................................................ 4A- 18 Disassembly and Reassembly .................................................................................... 4A- 19
Front Propeller Shaft ........................................................................................................ 4 A- 20
Removal and Installation.............................................................................................. 4A- 20
Disassembly ................................................................................................................. 4A - 22
Universal Joint Disassembly and Reassembly ......................................................... 4A- 24
Reassembly .................................................................................................................. 4A - 28


SECTIO
N 4A
PROPELLER SHAFT
TABLE OF CONTENTS
PA GE
Rear Propeller Shaft ..................................................................................................... 4A- 3
Torque Specifications .................................................................................................. 4A- 6
Front Propeller Shaft ................................................................................................... 4A- 7
M
ain D ata a n d S pecif ic atio ns ........................................................................................... 4 A - 3
Service Precautions
........................................................................................ .................4 A - 2

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4A-2 PROPELLER SHAFT
Service Precaution
WARNING: THIS VEHICLE HAS A
SUPPLEMENTAL RESTRAINT SYSTEM (SRS).
REFER TO THE SRS COMPONENT AND WIRING
LOCATION VIEW IN ORDER TO DETERMINE
WHETHER YOU ARE PERFORMING SERVICE ON
OR NEAR THE SRS COMPONENTS OR THE SRS
WIRING. WHEN YOU ARE PERFORMING
SERVICE ON OR NEAR THE SRS COMPONENTS
OR THE SRS WIRING, REFER TO THE SRS
SERVICE INFORMATION. FAILURE TO FOLLOW
WARNING COULD RESULT IN POSSIBLE AIR
BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM
REPAIRS.
CAUTION : Always use the correct fastener in the
proper location. When you replace a fastener,
use ONLY the exact part number for that
application. ISUZU/GM will call out those
fasteners that require a replacement afte
r
removal. ISUZU/GM will also call out the
fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do
not use supplemental coatings (Paints, greases,
or other corrosion inhibitors) on threaded
fasteners or fastener joint interfaces. Generally,
such coatings adversely affect the fastene
r
torque and the joint clamping force, and may
damage the fastener. When you install fasteners,
use the correct tightening sequence and
specifications. Following these instructions can
help you avoid damage to parts and systems.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4A-6 PROPELLER SHAFT

401R300006


Torque Specifications
N ⋅m (kgf ⋅m/lb ⋅ft)
RTW 34ASF000301


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

4A-8 PROPELLER SHAFT
Torque Specifications
N⋅m (kgf ⋅m/lb ⋅ft)





RUW 54ASF000501


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007