Timing ISUZU TF SERIES 2004 Owners Manual

6G-4 ENGINE LUBRICATION (6VE1 3.5L)
Disassembly
1. Remove crankshaft timing pulley.
2. Remove crankcase with oil pan.
3. Remove oil pipe.
4. Remove oil strainer.
5. Remove oil pump assembly.
6. Remove plug.
7. Remove spring.
8. Remove relief valve.
9. Remove oil pump cover.
10. Remove driven gear.
11. Remove drive gear.
12. Remove oil seal.
13. Remove O-ring.
Inspection and Repair
CAUTION: Make necessary correction or parts
replacement if wear, damage or any other abnormal
conditions are found during inspection.
Relief Valve (8)
 Check to see that the relief valve slides freely.
 The oil pump must be replaced if the relief valve
does not slide freely.
 Replace the spring and/or the oil pump assembly
(5) if the spring is damaged or badly worn.





051RS002
Body (14) and Gears (10, 11)
The pump assembly must be replaced if one or more of
the conditions below is discovered during inspection.
 Badly worn or damaged driven gear (10).
 Badly worn drive gear (11) driving face.
 Badly scratched or scored body sliding face (14) o
r
driven gear (10).
 Badly worn or damaged gear teeth.
Measure the clearance between the body and the
driven gear with a feeler gauge.
Standard : 0.10 mm–0.18 mm
(0.0039 in.–0.0070 in)
Limit : 0.20mm (0.0079 in)





051RS004
 Measure the clearance between the drive gear and
driven gear with a feeler gauge.
Standard : 0.11 mm–0.24 mm
(0.0043 in–0.0094 in)
Limit : 0.35mm (0.0138 in)




051RS003

6G-6 ENGINE LUBRICATION (6VE1 3.5L)


051RW002





051RW001
Legend
(1) Around Bolt Holes
(2) Around Dowel Pin


8. Install the new oil seal (12). Apply engine oil to the
oil seal lip before installation then use 5–8840–
2287–0 oil seal Installer, install oil seal.






015RS001
9. Install oil strainer (4) with O-ring (13).
Torque: 25 N




m (2.6 kg




m/18 lb ft)
10. Install oil pipe (3) with O-ring (13).
Torque: 25 N




m (2.6 kg




m/18 lb ft)
11. Install crankcase with oil pan (2).
 Remove oil on crankcase mounting surface and
dry the surface.

Apply a proper 4.5 mm (0.7 in) wide bead of
sealant (TB1207C or equivalent) to the
crankcase mounting surface. The bead must be
continuous.
 The crankcase must be installed within 5
minutes after sealant application to preven
t
premature hardening of sealant.
 Tighten fixing bolts to the specified torque.
Torque : 10 N




m (1.0 kg




m/7 lb ft)





013RW010
12. Install crankshaft timing pulley.

ENGINE LUBRICATION (6VE1 3.5L) 6G-9
Oil Pump
Removal
1. Disconnect battery ground cable.
2. Drain engine oil.
3. Remove crankcase assembly.
 Refer to removal procedure for Oil Pan and
Crankcase in this manual.
4. Remove crankshaft pulley.
 Refer to removal procedure for Crankshaf
t
Pulley in this manual.
5. Remove timing belt.
 Refer to removal procedure for Timing Belt in
this manual.
6. Remove timing pulley from crankshaft.
7. Remove four fixing bolts from oil filter assembly.
8. Remove oil strainer fixing bolts, remove oil straine
r
assembly with O-ring.
9. Remove three bolts from oil pipe and O-ring.
10. Remove eight oil pump fixing bolts, then oil pump
assembly.
11. Remove sealant from mounting surface of oil pump
assembly, cylinder block and take care not to
damage mounting surfaces of oil pump and cylinde
r
block.
Installation
1. Install oil pump assembly
 Apply sealant (TB-1207B or equivalent) to the oil
pump mounting surfaces as shown in the
illustration.
 The oil pump assembly must be installed within
5 minutes after sealant application before the
sealant hardens.
NOTE: Do not apply sealant to the oil ports.




051RW002
 Use 5–8840–2287–0 installer when installing
new oil seal.
 Apply engine oil to oil seal lip.
 Install oil pump assembly to the cylinder block.
NOTE: Do not damage oil seal during installation of oil
pump assembly.





015RS001

6G-10 ENGINE LUBRICATION (6VE1 3.5L)
 Tighten fixing bolts to the specified torque.
Torque : 25 N




m (2.5 kg




m/18 lb ft)



051RW001
2. Install oil pipe with O-ring, tighten fixing bolt to the
specified torque.
Torque : 10 N




m (1.0 kg




m/7 lb ft)
3. Install oil strainer with O-ring, tighten fixing bolt to
the specified torque.
Torque : 25 N




m (2.5 kg




m/18 lb ft)
4. Install oil filter assembly and tighten bolts to the
specified torque.
Torque : 25 N




m (2.5 kg




m/18 lb ft)





050RW001
Legend
(1) Oil Pump
(2) Oil Filter
(3) Oil Gallery
(4) From Oil Filter
(5) To Oil Filter


5. Install timing pulley on crankshaft.
Install timing belt.
 Refer to installation procedure for Timing Belt in
this manual.
6. Install crankshaft pulley.
 Refer to install procedure for Crankshaft Pulley
in this manual.
7. Install crankcase assembly.
 Refer to installation procedure for Oil Pan and
Crankcase in this manual.
8. Refill engine oil until full level on engine oil dipstick.

ENGINE LUBRICATION (6VE1 3.5L) 6G-11
Oil Pump Oil Seal
Removal
1. Disconnect battery ground cable.
2. Drain engine oil.
3. Remove crankshaft pulley.
 Refer to removal procedure for Crankshaf
t
Pulley in this manual.
4. Remove timing belt.
 Refer to removal procedure for Timing Belt in
this manual.
5. Remove timing pulley from crankshaft.
6. Remove oil pump oil seal using a sealer puller.
NOTE: Take care not to damage sealing surfaces of oil
pump and crankshaft when removing oil seal.

Installation
1. Install oil pump oil seal, apply engine oil to oil seal
lip, then install oil seal using 5–8840–2287–0
installer.





015RS001
2. Install timing pulley to crankshaft.
3. Install timing belt.
 Refer to installation procedure for Timing Belt in
this manual.
4. Install crankshaft pulley.
 Refer to installation procedure for Crankshaf
t
Pulley in this manual.
5. Refill engine oil until full level.

6G-12 ENGINE LUBRICATION (6VE1 3.5L)
Main Data and Specifications
General Specifications

Item Specifications
Oil capacity 5.3 liters

Torque Specifications
Crankcase, Oil pan, Timing belt tensioner, Timing pulley, timing belt cover, Oil pump, Oil gallery, Oil strainer
N




m (kg




m/lb ft)




RTW46GLF000101

6-2 ENGINE DIAGNOSIS (C24SE)
Engine Diagnosis
Hard Starting
1.Starting Motor Does Not Turn Over
Trouble Shooting Procedure
Turn on headlights and starter switch.
Condition Possible cause Correction
Headlights go out or dim
considerably Battery run down or under
charged Recharge or replace battery
Terminals poorly connected Clean battery posts and terminals
and connect properly
Starting motor coil circuit shorted Overhaul or replace
Starting motor defective Overhaul or replace
2.Ignition Trouble - Starting Motor Turns Over But Engine Does Not Start
Spark Test
Disconnect a high tension cable from any spark plug.
Connect the spark plug tester (use commercially
available tool), crank the engine, and check if a spark is
generated in the spark plug tester. Before cranking the
engine, make sure that the spark plug tester is properly
grounded. To avoid electrical shock, do not touch the
high tension cable while the engine is running.

Condition Possible cause Correction
Spark jumps across gap Spark plug defective Clean, adjust spark gap or replace
Spark plug wire in correct Connect properly or replace
Ignition timing incorrect Refer to Ignition System
Fuel not reaching fuel injector(s)
or engine Refer to item 3 (Trouble in fuel
system)
Valve timing incorrect Adjust
Engine lacks compression Refer to item 4 (Engine lacks
compression)
No sparking takes place Ignition coil disconnected or
broken Connect properly or replace
Electronic Ignition System with
module Replace
Poor connections in engine
harness Correct
Engine Control Module cable
disconnected or defective Correct or replace

ENGINE DIAGNOSIS (C24SE) 6-3
3.Trouble in Fuel System
Condition Possible cause Correction
Starting motor turns over and
spark occurs but engine does not
start. Fuel tank empty Fill
Water in fuel system Clean
Fuel filter clogged Replace filter
Fuel pipe clogged Clean or replace
Fuel pump defective Replace
Fuel pump circuit open Correct or replace
Evaporative Emission Control
system circuit clogged Correct or replace
Multiport Fuel Injection System
faulty Refer to "Electronic Fuel Injection"
section
4.Engine Lacks Compression
Condition Possible cause Correction
Engine lacks compression Spark plug loosely fitted or spark
plug gasket defective Tighten to specified torque or
replace gasket
Spark plug wire incorrect Connect properly or replace
Valve timing incorrect Adjust
Cylinder head gasket defective Replace gasket
Valve incorrectly seated Lap valve
Valve stem seized Replace valve and valve guide
Valve spring weakened Replace
Cylinder or piston rings worn Overhaul engine
Piston ring seized Overhaul engine.

Engine Compression Test Procedure
1. Start and run the engine until the engine
reaches normal operating temperature.
2. Turn the engine off.
3. Remove all the spark plugs.
4. Remove ignition coil fuse (15A) and disable the
ignition system.
5. Remove the fuel pump relay from the relay and
fuse box. 6. Engage the starter and check that the cranking
speed is approximately 300 rpm.
7. Install cylinder compression gauge into spark
plug hole.
8. With the throttle valve opened fully, keep the
starter engaged until the compression gauge
needle reaches the maximum level. Note the
reading.
9. Repeat the test with each cylinder.
The pressure difference between the individual
cylinders should not exceed 100kPa (14.5 psi).

6-4 ENGINE DIAGNOSIS (C24SE)
Rough Engine Idling or Engine Stalling
Condition Possible cause Correction
Trouble in fuel injection system Idle air control valve defective Replace
Throttle shutting off incomplete Correct or replace
Throttle position sensor circuit
open or shorted Correct or replace
Fuel injector circuits open or
shorted Correct or replace
Fuel injectors damaged Replace
Fuel pump relay defective Replace
Manifold Absolute Pressure
Sensor cable disconnected or
broken Correct or replace
Manifold Absolute Pressure
Sensor defective Replace
Engine Coolant Temperature
Sensor cable disconnected or
broken Correct or replace
Engine Coolant Temperature
Sensor defective Replace
Intake Air Temperature sensor
cable disconnected or broken Correct or replace
Intake Air Temperature sensor
defective Replace
Knock Sensor (KS) circuits open
or shorted Correct or replace
KS defective Replace
KS Module circuits open or
ground Correct or replace
KS Module defective Replace
Vehicle Speed Sensor circuit open
or shorted Correct or replace
Vehicle Speed Sensor defective Replace
Trouble in emission control
system Engine Control Module defective Replace
Canister purge solenoid circuit
open Correct
Canister purge solenoid defective Replace
Evaporative Emission Canister
Purge control valve defective Replace
Trouble in ignition system Refer to Hard Start
Troubleshooting Guide
Others Engine lacks compression Refer to Hard Start
Troubleshooting Guide
Valve incorrectly seated Lap valve
Air Cleaner Filter clogged Replace filter element
Valve timing incorrect Readjust
Idle air control valve broken Replace

6-10 ENGINE DIAGNOSIS (C24SE)
Troubleshooting Procedure

Condition Possible cause Correction
Piston pin noise
(Piston makes noise each time it
goes up and down) Piston pin or piston pin hole worn Replace piston, piston pin and
connecting rod assy

Troubleshooting Procedure
The slapping sound stops when spark plug on bad
cylinder is shorted out.

Condition Possible cause Correction
Timing belt noise Timing belt tension is incorrect Replace pusher or adjust the
tension pulley or replace timing
belt
Tensioner bearing defective Replace
Timing belt defective Replace
Timing wheels defective Replace
Timing belt comes in contact with
timing cover Replace timing belt and timing
cover
Valve noise Valve and valve guide seized Replace valve and valve guide
Valve spring broken Replace
Valve seat off-positioned Correct
Crankshaft noise Crankshaft end play excessive
(noise occurs when clutch is
engaged) Replace thrust bearing
Engine knocking Preignition due to use of spark
plugs of inadequate heat range Install Spark Plugs of adequate
heat range
Fuel too low in octane rating Replace fuel
Wide Open Throttle enrichment
system failure Refer to Section 6E
Selection of transmission gear
incorrect Caution operator or incorrect gear
selection
Engine overheating Refer to "Engine Lacks Power"
Others Water pump defective Replace
V-belt slipping Adjust tension of V-belt or replace
V-belt