steering ISUZU TF SERIES 2004 Workshop Manual

POWER-ASSISTED STEERING SYSTEM 3B-19

Reassembly
1. Install oil seal to front housing. Be sure to discard
used oil seal, and always use new parts fo
r
installation.
CAUTION: When installing the oil seal, be careful
not to damage the oil seal contacting surface of the
housing.
2. Install shaft assembly.
3. Install the vanes to roter with curved face in contac
t
with the inner wall of cam.
442RS005

4. Install roter and vanes to cam.
5. Install pin to front housing.
6. Install two new O-rings to front housing. Be sure to
discard used O-ring.
7. Install side plate.
CAUTION: When installing side plate, be careful not
to damage its inner surface. Damaged side plate
may cause poor pump performance, pump seizure
or oil leakage.
8. Install pump cartridge assembly to front housing.
9. Install snap ring to shaft end.
10. Install rear housing with a new O-ring. Be sure to
discard used O-ring. Then install bolt and tighten it
to specified torque.
Torque: 22-26 N




m (2.2-2.7kg




m/16-20 lb ft)
11. Install suction pipe with a new O-ring. Be sure to
discard used O-ring. Then install bolt and tighten it
to specified torque.
Torque: 7.8-12 N




m (0.8-1.2kg




m/69-104 lb in)
12. Install relief valve and spring.
13. Install connector with a new O-ring. Be sure to
discard used O-ring. Tighten the connector to
specified torque.
Torque: 49-69 N




m (5.0-7.0kg




m/36-51 lb ft)

Main Data and Specifications
General Specifications
Oil pump Type Vane
Operating fluid
ATF DEXRON®
III

3B-20 POWER-ASSISTED STEERING SYSTEM

Torque Specifications
4JH1-TC, 4JA1-TC, 4JA1-L N
m (kg
m/Ib ft)


RTW43BLF000501

POWER-ASSISTED STEERING SYSTEM 3B-21

Power Steering Pump and Associated Parts (C24SE)
RTW33BLF000801

Legend
(1) Pump Assembly
(2) Hose, Suction
(3) Hose, Flexible

(4) Bolt
(5) Connector, Pressure switch

Removal
1. Remove the drive belt.
2. Remove the pulley
3. Place a drain pan below the pump.
4. Disconnect the suction hose.
5. Disconnect the flexible hose.
6. Disconnect the oil pressure switch connector.
7. Remove the power steering fixing bolt and remove
the pump assembly.

Installation
1. Install the pump assembly to the pump braket,
tighten the fixing bolt to the specified torque.
Torque: 34-46 N·m (3.5-4.7 kg·m/25-34 lb ft)
2. Connector the oil pressure switch connector.
3. Install the flexible hose.
Tighten the eye bolt to specified torque.
Torque: 49-59 N·m (5.0-6.0 kg·m/36-43 lb ft)
4. Install the pulley and tighten the bolt to the specified
torque.
Torque: 69-88 N·m (7.0-9.0 kg·m/51-65 lb ft)

5. Install the drive belt.
6. Connect the suction hose, then fill and bleed
system.
Refer to Bleeding the Power Steering System in this
section.

3B-22 POWER-ASSISTED STEERING SYSTEM

Power Steering Pump Disassembled View

RTW43BMF000101

Legend
(1) Bolt
(2) Suction Pipe
(3) O-ring
(4) Shaft
(5) O-ring
(6) Front Housing
(7) O-ring
(8) O-ring
(9) Side plate
(10) Roter and vane
(11) Pin
(12) Cam
(13) Pump Cartridge
(14) O-ring


(15) Snap Ring
(16) Rear Housing
(17) Bolt
(18) Spring
(19) Relief Valve
(20) O-ring
(21) Connector
(22) Bush
(23) Pressure Switch Assembly

POWER-ASSISTED STEERING SYSTEM 3B-23

Disassembly
1. Clean the oil pump with solvent (plug the discharge
and suction ports to prevent the entry of solvent). Be
careful not to expose the oil seal of shaft assembl
y
to solvent.
2. Remove the bolt, suction pipe and O-ring.
Remove the O-ring.
3. Remove the connector, O-ring, relief valve and
spring.
4. Remove the pressure switch assembly.
5. Remove the bolt, rear housing and O-ring.
6. Remove the snap ring.
7. Remove the shaft assembly.
8. Remove the oil seal.
CAUTION: When removing the oil seal, be careful
not to damage the housing.
9. Remove the pump cartridge assembly from the fron
t
housing.
10. Remove two O-rings.
Inspection and Repair
Make all necessary adjustments, repairs, and part
replacements if wear, damage, or other problems are
discovered during inspection.


Rotor
442RS002
Check that the groove in the vane is free from excessive
wear and that the vane slides smoothly. When part
replacement becomes necessary, the pump cartridge
should be replaced as a subassembly.

Vane
442RS003
Sliding faces of the vane should be free from wear.
(Particularly the curved face at the tip that contact with
the cam should be free from wear and distortion). When
part replacement becomes necessary, the pump
cartridge should be replaced as a subassembly.

Cam
The inner face of the arm should have a uniform contact
pattern without a sign of step wear. When part
replacement becomes necessary, the pump cartridge
should be replaced as a subassembly.

3B-24 POWER-ASSISTED STEERING SYSTEM

Side Plate
The sliding faces of parts must be free from step wear
(more than 0.01 mm), which can be felt by the finger
nail. The parts with minor scores may be reused after
lapping the face.

Valve
The sliding face of the valve must be free from burrs
and damage. The parts with minor scores may be
reused after smoothing with emery cloth (#800 or finer).

Shaft
Oil seal sliding faces must be free from a step wear
which can be felt by the finger nail. Needle bearing fitting
face must be free from damage and wear.

O-ring, Oil Seal, Retaining Ring
Be sure to discard used parts, and always use new
parts for installation. Prior to installation, lubricate all
seals and rings with power steering fluid.

Pressure Switch
Check the switch operation as follows:
With engine idling and A/C on, turn the steering wheel
fully to the left; compressor should interrupt and engine
idle speed will increase. Shut off A/C and again turn
steering fully to the left; engine idle will increase. I
f
system fails to function properly, disconnect connector
at the pressure switch and repeat system check while
testing continuity across disconnected SW connector.

Reassembly
1. Install oil seal to front housing. Be sure to discard
used oil seal, and always use new parts fo
r
installation.
CAUTION: When installing the oil seal, be careful
not to damage the oil seal contacting surface of the
housing.
2. Install shaft assembly.
3. Install the vanes to roter with curved face in contact
with the inner wall of cam.
442RS005
4. Install rotor and vanes to cam.
5. Install pin to front housing.
6. Install two new O-rings to front housing. Be sure to
discard used O-ring.
7. Install side plate.
CAUTION: When installing side plate, be careful not
to damage its inner surface. Damaged side plate
may cause poor pump performance, pump seizure
or oil leakage.
8. Install pump cartridge assembly to front housing.
9. Install snap ring to shaft end.
10. Install rear housing with a new O-ring. Be sure to
discard used O-ring. Then install bolt and tighten it
to specified torque.
Torque: 22-26 N




m (2.2-2.7 kg




m/16-20 lb ft)
11. Install suction pipe with a new O-ring. Be sure to
discard used O-ring. Then install bolt and tighten it
to specified torque.
Torque: 7.8-12 N




m (0.8-1.2 kg




m/6-9 lb ft)
12. Install relief valve and spring.
13. Install connector with a new O-ring. Be sure to
discard used O-ring. Tighten the connector to
specified torque.
Torque: 49-69 N




m (5.0-7.0 kg




m/36-51 lb ft)
14. Install pressure switch assembly and tighten it to
specified torque.
Torque: 15-20 N




m (1.5-2.0 kg




m/11-14 lb ft)

POWER-ASSISTED STEERING SYSTEM 3B-25

Main Data and Specifications
General Specifications
Oil pump Type Vane
Operating fluid
ATF DEXRON®
III



Torque Specifications
C24SE N
m (kg
m/Ib ft)


RTW43BLF000401

3B-26 POWER-ASSISTED STEERING SYSTEM

Power Steering Pump and Associated Parts (6VE1)
RTW33BLF000701

Legend
(1) Pump Assembly
(2) Hose, Suction
(3) Hose, Flexible


(4) Bolt
(5) Connector, Pressure switch

Removal
1. Remove the drive belt.
2. Place a drain pan below the pump.
3. Disconnect the suction hose.
4. Disconnect the flexible hose.
5. Disconnect the oil pressure switch connector.
6. Remove the power steering fixing bolt and remove
the pump assembly.

Installation
1. Install the pump assembly to the pump braket,
tighten the fixing bolt to the specified torque.
Torque: 31-63 N·m (3.2-6.4 kg·m/23-46 lb ft)
2. Connector the oil pressure switch connector.
3. Install the flexible hose.
Tighten the eye bolt to specified torque.
Torque: 49 - 59 N·m (5.0 – 6.0 kg·m/36 - 43 lb ft)
4. Install the drive belt.
5. Connect the suction hose, then fill and bleed
system.
Refer to Bleeding the Power Steering System in this
section.

POWER-ASSISTED STEERING SYSTEM 3B-27

Power Steering Pump Disassembled View

RTW43BMF000301
Legend
(1) Bolt
(2) Suction Pipe
(3) O-ring
(4) Shaft Assembly
(5) Oil Seal
(6) Front Housing
(7) O-ring
(8) O-ring
(9) Side Plate
(10) Rotor and Vane
(11) Pin
(12) Cam

(13) Pump Cartridge Assembly
(14) O-ring
(15) Snap Ring
(16) Rear Housing
(17) Bolt
(18) Spring
(19) Relief Valve
(20) O-ring
(21) Connector
(22) Bush
(23) Pressure Switch Assembly

Disassembly
1. Clean the oil pump with solvent (plug the discharge
and suction ports to prevent the entry of solvent). Be
careful not to expose the oil seal of shaft assembl
y
to solvent.
2. Remove the bolt, suction pipe and O-ring.
Remove the O-ring.
3. Remove the connector, O-ring, relief valve and
spring.
4. Remove the pressure switch assembly.
5. Remove the bolt, rear housing and O-ring.
6. Remove the snap ring.
7. Remove the shaft assembly.
8. Remove the oil seal.
CAUTION: When removing the oil seal, be careful
not to damage the housing.
9. Remove the pump cartridge assembly from the front
housing.
10. Remove two O-rings.

3B-28 POWER-ASSISTED STEERING SYSTEM

Inspection and Repair
Make all necessary adjustments, repairs, and part
replacements if wear, damage, or other problems are
discovered during inspection.

Rotor
442RS002
Check that the groove in the vane is free from excessive
wear and that the vane slides smoothly. When par
t
replacement becomes necessary, the pump cartridge
should be replaced as a subassembly.

Vane
442RS003
Sliding faces of the vane should be free from wear.
(Particularly the curved face at the tip that contact with
the cam should be free from wear and distortion). When
part replacement becomes necessary, the pump
cartridge should be replaced as a subassembly.

Cam
The inner face of the arm should have a uniform contact
pattern without a sign of step wear. When part
replacement becomes necessary, the pump cartridge
should be replaced as a subassembly.

Side Plate
The sliding faces of parts must be free from step wear
(more than 0.01 mm), which can be felt by the finge
r
nail.
The parts with minor scores may be reused after lapping
the face.

Relief Valve
The sliding face of the valve must be free from burrs
and damage. The parts with minor scores may be
reused after smoothing with emery cloth (#800 or finer).

Shaft
Oil seal sliding faces must be free from a step wear
which can be felt by the finger nail. Bushing fitting face
must be free from damage and wear.

O-ring, Oil Seal, Snap Ring
Be sure to discard used parts, and always use new
parts for installation. Prior to installation, lubricate all
seals and rings with power steering fluid.

Pressure Switch
Check the switch operation as follows:
With engine idling and A/C on, turn the steering wheel
fully to the left; compressor should interrupt and engine
idle speed will increase. Shut off A/C and again turn
steering fully to the left; engine idle will increase. I
f
system fails to function properly, disconnect connecto
r
at the pressure switch and repeat system check while
testing continuity across disconnected SW connector.

Reassembly
1. Install oil seal to front housing. Be sure to discard
used oil seal, and always use new parts fo
r
installation.
CAUTION: When installing the oil seal, be careful
not to damage the oil seal contacting surface of the
housing.
2. Install shaft assembly.