lock ISUZU TF SERIES 2004 Workshop Manual

7A2-12 DIAGNOSIS (JR405E)
F0: Diagnostic Trouble Code
F0: Read DTC Infor As Stored By ECU
F1: Clear DTC Information
F1: Data Display
F2: Snapshot
F3: Miscellaneous Test
F0: Lamp
F0: Power Lamp Test
F1: 3rd Start Lamp Test
F2: AT Oil Temperature Lamp Test
F3: Transmission Check Light Test
F1: Solenoids
F0: Low & Reverse Brake Solenoid
F1: 2-4 Brake Solenoid
F2: High Clutch Solenoid
F3: Low Clutch Solenoid
F4: Line Pressure Solenoid
F5: Lock Up Duty Solenoid
F4: Programming
F0: Program VIN
F1: Lock ECU

F0: Diagnostic Trouble Code
The purpose of the "Diagnostic Trouble Codes" mode is to
display stored trouble code in the TCM.
When "Clear DTC Information" is selected, a "Clear DTC
Information", warning screen appears. This screen informs you
that by cleaning DTC's "all stored DTC information in the TCM
will be erased".
After clearing codes, confirm system operation by test driving
the vehicle.

F1: Data Display
The purpose of the "Data Display" mode is to continuously
monitor data parameters.
The current actual values of all important sensors and signals
in the system are display through F1mode.
See the "Typical Scan Data" section.

F2: Snapshot
"Snapshot" allows you to focus on making the condition occur,
rather than trying to view all of the data in anticipation of the
fault. The snapshot will collect parameter information around a
trigger point that you select.

F3: Miscellaneous Test:
The purpose of "Miscellaneous Test" mode is to check for
correct operation of electronic system actuators.

F4: Programming (Factory Use Only):
The purpose of "Programming" is to program VIN in the ECM
and lock the programmed data.

7A2-14 DIAGNOSIS (JR405E)
MISCELLANEOUS TEST
The state of each circuit can be tested by using miscellaneous test menus. Especially when DTC cannot be
detected, a faulty circuit can be diagnosed by testing each circuit by means of these menus.
Even DTC has been detected, the circuit tests using these menus could help discriminate between a mechanical
trouble and an electrical trouble.

Connect Tech 2 and select "Powertrain", "JR 405E" & "Miscellaneous Test".
F0: Lamps
The circuit is normal if the warning light in the meter panel comes on and goes out in accordance with Tech 2
instruction.

Lamps

F0: Power Lamp Test
F1: 3rd Start Lamp Test
F2: AT Oil Tempeature Lamp Test
F3: Transmission Check Light Test


F0: Power Lamp Test


Power Lamp Test

Power Lamp Off



 Press "Active" key.
Then, "POWER DRIVE" indicator lamp is turned on in the meter panel.
 Press "Inactive" key.
Then, "POWER DRIVE" indicator lamp is turned off in the
meter panel.
 Press "Quit" Key to cancel the test.
F1: 3rd Start Lamp Test
F2: AT Oil Temperature Lamp Test
F3: Transmisstion Check Light Test
Test procedure is same as "F0: Power Lamp Test".
The circuit is normal if the warning light in the meter panel
comes on and goes out in accordance with Tech 2 instruction.

F1: Solenoids
The circuit is normal if clicking sound is generated in accordance with Tech 2 instruction.

Solenoids
F0: Low & Reverse Brake Solenoid
F1: 2-4 Brake Solenoid
F2: High Clutch Solenoid
F3: Low Clutch Solenoid
F4: Line Pressure Solenoid
F5: Lock Up Duty Solenoid

DIAGNOSIS (JR405E) 7A2-15
F0: Low & Reverse Brake Solenoid

Low & Reverse Brake Solenoid

Low & Reverse Brake Duty 0%



 Press "Active" key.
Then, duty datio is indicated 100 % and "clicking sound" is
generated from the transmission control valve.
 Press "Inactive" key.
Then, duty datio is indicated 0 % and "clicking sound" is
generated from the transmission control valve.
 Press "Quit" Key to cancel the test.

F0: Low & Reverse Brake Solenoid
F1: 2-4 Brake Solenoid
F2: High Clutch Brake Solenoid
F3: Low Clutch Solenoid
F4: Line Pressure Solenoid
F5: Lock Up Duty Solenoid

Test procedure is same as "F0: Low & Revese Brake
Solenoid"
The circuit is normal if clicking sound is generated in
accordance with Tech 2 instruction.

7A2-34 DIAGNOSIS (JR405E)


Flash Code
(P-Code)

CHECK TRANS Flash Pattern

Description
CHECK
TRANS
Warning

34 (P0768) Low Clutch Duty Solenoid FailureON


35 (P0748) Line Pressure Solenoid Failure ON


36 (P1860) Lock-up Duty Solenoid Failure ON


41 (P0731) 1stGearRatioError ON


42 (P0732) 2ndGearRatioError ON


43 (P0733) 3rdGearRatioError ON


44 (P0734) 4thGearRatioError ON


51 (P1750) ON

Low & Reverse Brake Fail-safe
Valve Failure

52 (P1755) 2-4BrakeFail-safeValveFailure ON


- (P0602) No Flash Code ECU Programming Error ON

DIAGNOSIS (JR405E) 7A2-35
FAIL-SAFEFUNCTION
Fail-Safe Condition
Flash Code
(P-Code)

Description
CHECK
TRANS
Warning

Gear Shift
Solenoid
Line
Pressure
Solenoid

Lock-up

Remark
11
(P0722)
Vehicle peed Sensor No
Signal ON 3rdFix All Stop - Inhibited
13
(P0727)
Engine Revolution Sensor
No Signal ON - - - Inhibited
14
(P0717)
Turbine Speed Sensor No
Signal ON 3rdFix All Stop - Inhibited
15
(P0710)
ATF Temperature Sensor
Failure OFF 3,2,L - - Inhibited*1
16
(P0560)
System Voltage Failure ON 3rdFix All Stop - Inhibited*2
17
(P0705)
Inhibitor Switch Failure ON 3rdFix All Stop - Inhibited
22
(P1120)
Throttle Signal Failure ON 3rdFix All Stop - Inhibited
25
(P1875)
GND Return Circuit
Failure ON 3rdFix All Stop - Inhibited*2
26
(P1853)
Low & Reverse Brake
Pressure Switch Failure ON No Fail-safe Function
27
(P1858)
2-4 Brake Pressure
Switch Failure ON No Fail-safe Function
28
(P1863)
High Clutch Pressure
Switch Failure ON No Fail-safe Function
31
(P0753)
Low & Reverse Brake
Duty Solenoid Failure ON 3rdFix All Stop - Inhibited
32
(P0758)
2-4 Brake Duty Solenoid
Failure ON 3rdFix All Stop - Inhibited
33
(P0763)
High Clutch Duty Solenoid
Failure ON 3rdFix All Stop - Inhibited
34
(P0768)
Low Clutch Duty Solenoid
Failure ON 3rdFix All Stop - Inhibited
35
(P0748)
Line Pressure Solenoid
Failure ON - - Stop -
36
(P1860)
Lock-up Duty Solenoid
Failure ON - - - Inhibited
41
(P0731)
1stGearRatioError ON No Fail-safe Function
42
(P0732)
2ndGearRatioError ON No Fail-safe Function
43
(P0733)
3rdGearRatioError ON No Fail-safe Function
44
(P0734)
4thGearRatioError ON No Fail-safe Function
51
(P1750)
Low & Reverse Brake
Fail-safe Valve Failure ON 3rdFix All Stop - Inhibited
52
(P1755)
2-4 Brake Fail-safe Valve
Failure ON 3rdFix All Stop - Inhibited
-
(P0602)
ECU Programming Error ON No Fail-safe Function
*1: When the engine speed is more than 470 rpm for 10 minuets, the lock-up and gear shift to 4th (over-drive) are
allowed.
*2: In case of fail-safe valve failure, gear shift to 4th (over-drive) is inhibited.

7A2-36 DIAGNOSIS (JR405E)
DTC P0722 (Flash Code 11) Vehicle Speed Sensor No Signal


Speed
Sensor
TCM



B13
H23
(4)C95
(13)E30
(2)
(1)
(3)
E10
Key SW
YEL/RED
BLK YEL/RED

Speed Sensor Turbine Sensor

Setting Condition:

When the vehicle speed exceeds 5 km/h with the turbine speed over 1000 rpm for 5 seconds, after 25.5
seconds elapsed in D, 3, 2 or L range.

Fail Safe:

When the vehicle is running, the gear position selected at the trouble detection is held and the lock-up is
inhibited.

After the vehicle stopped, all solenoid operations stop (OFF) and the gear is fixed to the 3rd.

Possible Cause:

Speed sensor malfunction.

Sensor wheel (parking gear) malfunction.

Large sensing gap between speed sensor and sensor wheel (parking gear).

Sensor wire open circuit, short circuit to battery or short circuit to ground between speed sensor terminal 1 and
TCM terminal B13 (C95).

Sensor wire open circuit or short circuit to ground of the harness between speed sensor terminal 2 and power
supply circuit.

Sensor wire open circuit or short circuit to battery between speed sensor terminal 3 and ground circuit.

Poor connection of each connector.

7A2-38 DIAGNOSIS (JR405E)
DTC P0727 (Flash Code 13) Engine Revolution Sensor No Signal



RED
TDC
Sensor TCM



A7
C94 (7)
BLK/RED
WHT
C56
(27)
E9
(1)

(2)
(3)

C57 (98)

(90)
(101)

ECM




C56 (ECM-A)

Setting Condition:

The engine speed becomes 0 rpm for 2 seconds while the vehicle is running at the over 40 km/h.

Fail Safe:

Lock-up is inhibited.

Possible Cause:

Crank position sensor malfunction.

Sensor wheel (flywheel) malfunction.

Large sensing gap between speed sensor and sensor wheel (flywheel).

Faulty input signal from crank position sensor to ECM.

Signal wire open circuit or short circuit to battery between ECM A24 and TCM terminal A7 (C94).

Poor connection of each connector.

Reference:
When the engine speed 2000rpm, following signal is outputted.
Measurement terminal: A7 (C94) and B5 (C95)
-AC range by circuit tester: Approximately 6.2V
-Oscilloscope: Following wave form can be found.

7A2-40 DIAGNOSIS (JR405E)
DTC P0717 (Flash Code 14) Turbine Speed Sensor No Signal

Turbine
Sensor TCM



B3
H23 (9)C95 (3) E31 (2)
(1)
(3)
E10
Key SW
BRN/RED
WHT
BLK BRN/RED


Speed Sensor Turbine Sensor

Setting Condition:

The turbine speed below 300 rpm for 2 seconds while the vehicle is running at the speed over 40 km/h with the
engine speed over 1500 rpm in the D, 3, 2, or L range.

Fail Safe:

When the vehicle is running, the gear position selected at the trouble detection is held and the lock-up is
inhibited.

After the vehicle stopped, all solenoid operations stop (OFF) and the gear is fixed to the 3rd.

Possible Cause:

Turbine speed sensor malfunction.

Sensor wheel (reverse & high clutch drum) malfunction.

Large sensing gap between speed sensor and sensor wheel (reverse & high clutch drum).

Sensor wire open circuit, short circuit to battery or short circuit to ground between turbine speed sensor terminal
1 and TCM terminal B3 (C95).

Sensor wire open circuit or short circuit to ground between turbine speed sensor terminal 2 and power supply
circuit.

Sensor wire open circuit or short circuit to battery between turbine speed sensor terminal 3 and ground circuit.

Poor connection of each connector.

7A2-42 DIAGNOSIS (JR405E)
DTC P0710 (Flash Code 15) ATF Temperature Sensor Failure

ATF
Temp.
Sensor
TCM


B4 (+)



B14 (-)

H23 (8)



(3)
C95 (4)



(14)
BLU
Terminal
Assembly
BLU/BLKE54 (2)



(8)
BLU
BLU/BLK


Setting Condition:

The condition in which the voltage of oil temperature sensor is below 0.1V (146 C) and ATF temperature
warning lamp ON in the P or N range lasts for more than 5 minutes.
Or

The vehicle speed exceeds 20 km/h and the voltage of oil temperature sensor exceeds 2.43V (-40 C) for more
than 10 seconds.

Fail Safe:

The lock-up is inhibited, and TCM is controlled ATF temperature 80 C condition as substitute.

When the engine speed is more than 470 rpm for 10 minuets, the lock-up and gear shift to 4th (over-drive) are
allowed.

Possible Cause:

Oil temperature sensor wire open circuit or short circuit.

Oil temperature sensor malfunction.

Power supply wire open circuit, short circuit to battery or short circuit to ground between oil temperature sensor
and TCM terminal B4 (C95).

Ground wire open circuit or short circuit to battery between oil temperature sensor terminal and TCM terminal
B14 (C95).

Poor connection of each connector.

Reference:
Following output voltage and resistance can be measured by circuit tester.
Measurement terminal: B4 (C95) and B14 (C95)

ATF Temperature Output Voltage Resistance ATF Temperature Output Voltage Resistance
20
C
1.55V 2,500  80
C
0.5V 320 
40
C 1.08V 1,160  100
C
0.3V 190 
60
C
0.7V 590  120
C
0.2V 120 

DIAGNOSIS (JR405E) 7A2-43
DTC P0560 (Flash Code 16) System Voltage Failure
TCM


A1 (+B)



B5

B15

H23 (15)C95 (5)
(15)
BLK/YEL
BLK
BLK
Battery
C94
(1)
BLK


Setting Condition:

The supply voltage is below 10V and the engine speed exceeds 1000 rpm for more than 1 second.

Fail Safe:

When the vehicle is running, the gear position selected at the trouble detection is held and the lock-up is
inhibited.

After the vehicle stopped, all solenoid operations stop (OFF) and the gear is fixed to the 3rd. (In case of fail-safe
valve failure, gear shift to 4th (over-drive) is inhibited.)

Possible Cause:

Alternator or battery malfunction.

Power supply wire open circuit or short circuit to ground between power supply and TCM terminal A1 (C94).

Ground wire open circuit or short circuit to battery between ground location and TCM terminal B5 (C95) or B15
(C95).

Poor connection of each connector.