transmission oil ISUZU TF SERIES 2004 Manual PDF

MANUAL TRANSMISSION 7B1-79

5. Install top gear bearing snap ring (9) and counter
front bearing snap ring (7).


Use a pair of snap ring pliers to install the snap
rings to the mainshaft and countershaft.


The snap rings must be fully inserted into the
bearing snap ring groove.
6. Front cover with oil seal (8).
Front Cover Oil Seal Replacement


Remove the oil seal from the front cover.


Apply engine oil to a new oil seal outer
circumference.

Apply recommended grease to the oil seal lip.


Use the oil seal installer 5-8840-0026-0 to install
the oil seal to the front cover.
220R3000020
8. Apply molybdenum disulfide type grease to the
areas as shown in the figure and install shift fork (6).
(Diesel engine, C24NE)
F07L100026
9. Install the fulcrum bridge to the transmission case.
(6VE1)
Torque: 38 N




m (3.9 kg




m/28 lb




ft)
RTW37ASH0002

Legend
(1) Fulcrum bridge

10. Apply molybdenum disulfide type grease to the pin
hole inner circumferences and thrust surfaces.
(6VE1)
11. Attach the shift fork to the fulcrum bridge and insert
the pin from below of the fulcrum bridge. (6VE1)

7B1-84 MANUAL TRANSMISSION

Reassembly
1. Install rev-5th shift arm and reverse inhibitor (6) and
rev-5th shift rod (5).

Apply oil to the reverse inhibitor inner surface.

Install the shift rod in the intermediate plate (12).


Hold a round bar against the shift rod end lower
face to protect it against damage.

Install a new spring pin.
Never reinstall the used spring pin.


Install the interlock pin (11) in the intermediate
plate (12).
Do not allow the interlock pin to fall from the
intermediate plate (12).
2. Install 1st-2nd shift arm (10) and 3rd-4th shift arm(9)
to intermediate plate and gear assembly (12).
3. Install 3rd-4th shift rod (8) and 1st-2nd shift rod (7).


Install the interlock pin (11) in the intermediate
plate and gear assembly (12).


Install the 3rd-4th shift rod (8) in the intermediate
plate (12).
Do not allow the interlock pin to fall from the
intermediate plate.


Install the interlock pin (11) and then 1st-2nd
shift rod (7) in the intermediate plate (12).
Do not allow the interlock pin to fall from the
intermediate plate.


Hold a round bar against the shift rod end lower
face to protect it against damage.

Install a new spring pin.
Never reinstall the used spring pin.

230RS007
4. Install spring (4).
5. Put detent balls (3) in the intermediate plate holes.


Apply oil to the detent balls.
6. Install detent springs (2) and detent spring plate and
gasket (1).


Install a new gasket and the detent spring plate.


Tighten the detent spring plate bolts to the
specified torque.
Torque: 25 N




m (2.5 kg




m/18 lb




ft)


220RS030

Legend
(1) Warped

MANUAL TRANSMISSION 7B1-85

Reverse Gear and 5th Gear
Disassembled View
226R300024

Legend

(1) Collar Snap Ring (15) Counter 5th Gear
(2) Oil Seal Collar (16) Counter Reverse Gear
(3) Ball Bearing (17) 5th Gear
(4) Retainer (18) 5th Block Ring
(5) Thrust Plate (19) Needle Bearing
(6) Thrust Washer and Lock Ball (20) Mainshaft Nut
(7) Reverse Idler Gear Snap Ring (21) Rev-5th Synchronizer Assembly
(8) Reverse Idler Gear Assembly (22) Reverse Block Ring
(9) Idle Shaft Pin (23) Reverse Gear
(10) Thrust Washer (24) Needle Baring
(11) Reverse Idler Gear (25) Bearing Plate and Screw
(12) Reverse Idler Shaft (26) Bearing Snap Ring
(13) Bearing Snap Ring (27) Intermediate Plate
(14) Ball Bearing

7B1-86 MANUAL TRANSMISSION

Disassembly
1. Use a pair of snap ring pliers to remove the collar
snap ring (1).
2. Set the retaining ring remover 5-8840-2158-0 and
puller 5-8840-2027-0 to the retainer (4) and the
mainshaft end.
262RW079
3. Remove the retainer (4) together with the bearing
(3) and the oil seal collar (2).
The universal puller may be used in place of the
retaining ring remover.
4. Remove thrust plate (5) and thrust washer and lock
ball (6).
5. Use a pair of snap ring pliers to remove reverse idler
gear snap ring (7).

226RS004

6. Remove the reverse idler gear assembly (8) from
the intermediate plate (27).

226RS005
7. Remove idle shaft pin (9), thrust washer (10),
reverse idler gear (11), and reverse idler shaft (12).
8. Use a pair of snap ring pliers to remove the snap
ring (13).
9. Attach a universal puller to the counter gear shaft.
Use a universal puller to remove the ball bearing
(14) and the counter 5th gear (15).

226RS006
10. Remove counter reverse gear (16).

7B1-90 MANUAL TRANSMISSION

6. Mesh the 1st-2nd and 3rd-4th synchronizers with
both the 1st and 3rd gears (double engagement).

226RS015
This will prevent the mainshaft from turning.
7. Install the new mainshaft hub nut.
Use the mainshaft nut wrench 5-8840-2156-0 to
tighten the mainshaft nut (20) to the specified
torque.
Torque: 137 N




m (14 kg




m/101 lb




ft)
226RW214


8. Use a punch to stake the mainshaft nut (20).

226RW153
9. Install needle bearing (19), 5th block ring (18), and
5th gear (17).
10. Apply engine oil to the counter reverse gear (16) and
the reverse gear (23).
Install the counter reverse gear (16) to the counter
shaft.
The reverse gear projection must be facing the
intermediate plate.

226RW151

MANUAL TRANSMISSION 7B1-91

11. Install the counter 5th gear (15) to the counter shaft.

226RS019
12. Install ball bearing (14) and bearing snap ring (13)
by performing the following steps:


Select the snap ring which will provide the
minimum clearance between the ball bearing
and the snap ring.

226RS020


There are six snap ring sizes available.
The snap rings are color‐coded to indicate
their thickness.

226RS021
Ball Bearing and Snap Ring Clearance
Standard: 0 - 0.15 mm (0 - 0.0059 in)

Snap Ring Availability
Thickness Color Coding
1.1 mm (0.043 in) White
1.2 mm (0.047 in) Yellow
1.3 mm (0.051 in) Blue
1.4 mm (0.055 in) Pink
1.5 mm (0.059 in) Green
1.6 mm (0.063 in) Brown


Use a pair of snap ring pliers to install the snap
ring(13) to the counter gear shaft.
The snap ring must be fully inserted into the
counter gear shaft snap ring groove.
13. Assemble reverse idler shaft (12), reverse idler gear
(11), thrust washer (10), and idle shaft pin (9) into
reverse idler gear assembly (8).
The trust washer should be assembled as oil groove
faces to gear side.

MANUAL TRANSMISSION 7B1-93


226RS024


Apply grease to the thrust washer and the lock
ball.


Install the thrust washer and the lock ball.
16. Install thrust plate (5) and retainer (4).
17. Apply engine oil to the bearing inner and outer
circumference.
Use the installer 5-8840-2159-0 to install the ball
bearing (3) to the mainshaft.
226L100002
18. Apply engine oil to the oil seal collar inner
circumference.
Install the oil seal collar (2) to the mainshaft by using
the installer 5-8840-2159-0.
19. Install the oil seal collar snap ring (1).

MANUAL TRANSMISSION 7B1-101

Clutch Hub Spline Play

Set a dial indicator to the clutch hub to be
measured.

226RS042


Move the clutch hub as far as possible to both the
right and the left.
Note the dial indicator reading.
If the measured value exceeds the specified limit,
the clutch hub must be replaced.

Clutch Hub Spline Play
Standard Limit
1st-2nd
3rd-4th 0 - 0.1 mm
(0 - 0.004 in) 0.2 mm
(0.008 in)
Rev. 5th 0 - 0.2 mm
(0 - 0.008 in) 0.3 mm
(0.012 in)
Ball Bearing Play


Use a dial indicator to measure the ball bearing play.
Ball Bearing Play
Limit: 0.2 mm (0.008 in)




226RS043

Reassembly
1. Install center roller bearing (29) to counter gear
shaft (30).


Apply engine oil to the bearing inner and outer
circumferences.


Install the roller bearing in the proper direction.
NOTE: Check that outer race moves only in the
direction of arrow.

226RS044
2. Install front roller bearing (28) by performing the
following steps.


Use bearing installer 5-8840-2194-0 to install the
front roller bearing inner race to the counter gear
shaft (30).


Install the outer race and roller assembly.
The snap ring groove must be facing the
transmission front side.

7B1-102 MANUAL TRANSMISSION



Use bearing installer 5-8840-2194-0 to install the
ring.



226RS045

Legend
(1) Ring
(2) Outer Race and Roller Assembly
(3) Inner Race
3. Install bearing snap ring (27) to counter gear shaft
(30).
4. Apply engine oil to the needle bearing (25) and the
2nd gear (24) thrust surfaces.
Install the needle bearing (25) and the 2nd gear (24)
to the mainshaft (26).
The 2nd gear (24) dog teeth must be facing the
transmission rear side.

226RS046

5. Assemble 2nd inside ring (23), 2nd outside ring (22),
and 2nd block ring (21).


Apply engine oil to the synchronizer ring friction
surfaces.

226RS047

Legend
(1) Block Ring
(2) Outside Ring
(3) Inside Ring
(4) 2nd Gear
(5) Needle Bearing
6. Assemble 1st-2nd synchronizer assembly (20) by
performing the following steps:
1. Check that the inserts (3) fit snugly into the
clutch hub (5) insert grooves.
2. Check that the inserts springs (4) are fitted to
the inserts as shown in the illustration.
3. Check that the clutch hub (5) and the sleeve (6)
slide smoothly.

7B1-104 MANUAL TRANSMISSION


226RS031
9. Install needle bearing (18), 1st block ring (17), 1st
outside ring (16), 1st inside ring (15), and 1st gear
(14).


Apply engine oil to the needle bearing, 1st gear
thrust surfaces and synchronizer ring friction
surfaces.


The 1st gear dog teeth must be facing the
transmission front side.

226RS053

Legend
(1) 1st Gear
(2) Needle Bearing
(3) Inside Ring
(4) Outside Ring
(5) Block Ring

10. Install the 1st gear thrust bearing and the race(13) to
the main shaft.
The thrust bearing side must be facing the
transmission front side.

226RS054
11. Apply engine oil to the mainshaft ball bearing (12)
and the mainshaft (26).
Install the ball bearing (12) and needle bearing collar
(11) to the mainshaft (26).
The ball bearing snap ring groove must be facing
the transmission rear side.
Use a bench press and installer 9-8522-1165-0 to
slowly force the collar into place.

226RS055