Interior JAGUAR XFR 2010 1.G User Guide

DTC Description Possible Causes Action U3000-04
Control Module -
System internal
failures
Diversity antenna amplifier internal
failure
Renew the amplifier module U3000-4A
Control Module -
Incorrect
component
installed
Diversity antenna amplifier internal
incorrect component installed
- The module has been installed to
a vehicle not configured to accept
it
Using the manufacturer approved
diagnostic system select the vehicle
configuration main menu, select configure
existing modules menu and program the
module U3000-55
Control Module -
Not configured
Diversity antenna amplifier not
configured correctly
Using the manufacturer approved
diagnostic system select the vehicle
configuration main menu, select configure
existing modules menu and program the
module U3000-87
Control Module -
Missing message
Missing message
Using the manufacturer approved
diagnostic system select the vehicle
configuration main menu, select configure
existing modules menu and program the
module U3000-98
Control Module -
Component or
system over
temperature
Diversity antenna amplifier component or
system over temperature
Consider moving the amplifier mounting
position to prevent unit overheating. Cool
the vehicle interior down by ensuring it is
in the shade and have the A/C on cool.
When cool, clear the DTC and retest. If
the problem persists, renew the amplifier
module U3003-62
Battery Voltage -
Signal compare
failure
Mismatch in battery voltage of 2 volts or
more for longer than 1 minute, between
the measured battery voltage at the
Digital Audio Control Module C and the
battery voltage signal sent from the Rear
Junction Box.
Refer to the electrical guides and check
that power supply voltage at Digital Audio
Control Module C and Rear Junction Box is
not different by more than 2 volts. Rectify
as required

5
Maximum permitted front axle loading 6
Maximum permitted rear axle loading 7
Date of manufacture 8
Interior trim code 9
Paint code VIN Label (North America)



Item
Description 1
Maximum permitted front axle loading 2
Date of manufacture 3
Gross vehicle weight 4
Maximum permitted rear axle loading 5
VIN 6
Type 7
Interior trim code 8
Paint code

1
Date of manufacture 2
VIN 3
Interior trim code 4
Paint code VIN Label (Saudi Arabia and Gulf States)

1
Maximum permitted front axle loading 2
Date of manufacture 3
Gross vehicle weight 4
Maximum permitted rear axle loading 5
VIN 6
Paint code 7
Interior trim code 8
Type VIN Label (China)

1
Occupant number 2
Engine specification (Type/Capacity/Power) 3
VIN 4
Trade mark 5
Vehicle type 6
Gross vehicle weight 7
Date of manufacture 8
Manufacturer name VIN Label (Argentina)



Item
Description 1
VIN 2
Trade mark and manufacturer adress (in Spanish) 3
Gross vehicle weight 4
Gross train weight 5
Maximum permitted front axle loading 6
Maximum permitted rear axle loading 7
Date of manufacture 8
Interior trim code 9
Paint code Automatic Transmission Number

The serial number of the transmission unit is displayed on a metal label or bar code (if equipped) attached to the transmission
casing.

Engine Number(s)

Engine Number - 2.2L Diesel

The serial number is stamped on an engine web on the right-hand side of the cylinder block behind the engine mounting.

Engine Number - 2.7L Diesel

The serial number is stamped on an engine web on the right-hand side of the cylinder block behind the engine mounting.

Engine Number - 3.0L Diesel

The serial number is stamped on an engine web on the right-hand side of the cylinder block behind the engine mounting.

Engine Number - 3.0L

The engine number is contained on a bar code label on the front cover and is also stamped in the cylinder block casting on the www.JagDocs.com

Published: 06-Jun-2013
Front Suspension - Front Stabilizer Bar V8 5.0L Petrol/V8 S/C 5.0L Petrol
Removal and Installation


Removal


NOTE: Removal steps in this procedure may contain installation details.

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.

3. Refer to: Air Conditioning (A/C) System Recovery, Evacuation and Charging (412-00 Climate Control System - General Information, General Procedures).

4. Refer to: Radiator Splash Shield (501-02 Front End Body Panels, Removal and Installation).

5. Refer to: Air Deflector (501-02 Front End Body Panels, Removal and Installation).

6. Refer to: Front Wheel Bearing and Wheel Hub - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol (204-01 Front Suspension, Removal and Installation).

7. Refer to: Engine Cover - V8 5.0L Petrol/V8 S/C 5.0L Petrol (501-05 Interior Trim and Ornamentation, Removal and Installation).

8.
Secure the radiator assembly. 303-021
Engine support bracket Special Tool(s) www.JagDocs.com

Interior Trim and Ornamentation, Removal and Installation).

Vehicles with active damping

2. Disconnect the active suspension damper electrical connector.













All vehicles

3. Remove the shock absorber and spring assembly top mount
nuts. TORQUE: 28 Nm













4. WARNING: Make sure to support the vehicle with axle stands.
Raise the vehicle.

5. Remove the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

Interior Trim and Ornamentation, Removal and Installation). Vehicleswithactivedamping

Published: 11-May-2011
Wheels and Tires - Tire Pressure Monitoring System (TPMS) Module
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details.

1. Switch the igntion off.

2. Remove the right-hand front seat.

Refer to: Front Seat (501-10 Seating, Removal and Installation).
3. Refer to: B-Pillar Lower Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).

4. Detach and reposition the floor covering.
5. www.JagDocs.com

Vehicle Dynamic Suspension - Adaptive Damping Module
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Front Seat (501-10 Seating, Removal and Installation).
2. Refer to: B-Pillar Lower Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).

3. Detach and reposition the floor covering.
4.
5. www.JagDocs.com