Crank JAGUAR XFR 2010 1.G Service Manual

Engine - V8 S/C 5.0L Petrol - Crankshaft Rear Seal
Removal and Installation

Special Tool(s)






Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 12-May-2014

1. Refer to: Flexplate (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).

2. 303-1442
Rear Crankshaft Seal Installer JLR-303-1622
Alignment Tool, Engine Rear Oil Seal

Engine - V8 S/C 5.0L Petrol - Flexplate
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. CAUTION: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

3. Refer to: Transmission - V8 5.0L Petrol/V8 S/C 5.0L Petrol (307-01B Automatic Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8
S/C 5.0L Petrol, Removal).

4. CAUTIONS:


Install all the bolts finger tight before final tightening.


The bolts can only be used 3 times, mark the bolts
with a center punch. If 2 punch marks are visible, discard
the bolts.
Make sure that no components fall off during removal.
Install the bolts in the noted position.

NOTES:


Make sure the crankshaft and flexplate mating faces
are clean before installation.


Make sure that the crankshaft is not rotated.


Tighten the retaining bolts working diagonally.
Torque:
Stage 1:45 Nm Stage 2:90°
Installation

1. To install, reverse the removal procedure.

303-1442
Rear Crankshaft Seal Installer
303-1443
Rear Crankshaft Cover Alignment Tool Removal

NOTES:

Removal steps in this procedure may contain installation details.
Some variation in the illustrations may occur, but the essential information is always correct. Published: 03-Dec-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Do not work on or under a vehicle supported only by a jack. Always
support the vehicle on safety stands.

Raise and support the vehicle.

3. Refer to: Crankshaft Pulley (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).

4. Refer to: Engine (303-01D Engine - V8 S/C 5.0L Petrol, Installation).

5. CAUTIONS:


The bolts can only be used 3 times, mark the bolts with a center punch.
If 2 punch marks are visible, discard the bolts.


Make sure that no components fall off during removal.

NOTES:


Make sure that the crankshaft is not rotated.


Make sure the crankshaft and flexplate mating faces are clean before
installation.


6.
7.
8.

49. CAUTIONS:


Install all the bolts finger tight before final tightening.


The bolts can only be used 3 times, mark the bolts with a center punch.
If 2 punch marks are visible, discard the bolts.


Install the bolts in the noted position.

NOTES:


Make sure that the crankshaft is not rotated.


Make sure the crankshaft and flexplate mating faces are clean before
installation.


Tighten the retaining bolts working diagonally.

Torque:
Stage 1:45 Nm Stage 2:90°
50. Refer to: Engine (303-01D Engine - V8 S/C 5.0L Petrol, Installation).
51. Refer to: Crankshaft Pulley (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).

52. Lower the vehicle.

53. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

6. NOTE: Tsubaki timing drive only.
Install the lower timing chain making sure the coloured
chain links align correctly with the fuel rail high-pressure
fuel pumps camshaft and crankshaft sprocket markings.

7. CAUTION: Make sure that the tensioner spring is
correctly located.


NOTE: Tsubaki timing drive only.
Torque: 21 Nm









8. NOTE: INA timing drive only.
Install the lower timing chain making sure the coloured
chain links align correctly with the fuel rail high-pressure
fuel pumps camshaft and crankshaft sprocket markings.

Engine - V8 S/C 5.0L Petrol - Timing Cover
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 12-Sep-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

3. Refer to: Accessory Drive Belt (303-05D Accessory Drive - V8 S/C 5.0L Petrol, Removal and Installation).

4. Refer to: Accessory Drive Belt Tensioner (303-05D Accessory Drive - V8 S/C 5.0L Petrol, Removal and Installation).

5. Refer to: Thermostat Housing - Vehicles With: Supercharger (303-03C Engine Cooling - V8 5.0L Petrol/V8 S/C 5.0L Petrol, Removal and
Installation).

6. Refer to: Valve Cover LH (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).

7. Refer to: Valve Cover RH (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).

8. Refer to: Crankshaft Pulley (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).


9. NOTE: Engine shown removed for clarity.

12.
Refer to: Crankshaft Pulley (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).

13. Refer to: Valve Cover RH (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).

14. Refer to: Valve Cover LH (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).

15. Refer to: Thermostat Housing - Vehicles With: Supercharger (303-03C Engine Cooling - V8 5.0L Petrol/V8 S/C 5.0L Petrol, Removal and
Installation).

16. Refer to: Accessory Drive Belt Tensioner (303-05D Accessory Drive - V8 S/C 5.0L Petrol, Removal and Installation).

17. Refer to: Accessory Drive Belt (303-05D Accessory Drive - V8 S/C 5.0L Petrol, Removal and Installation).

18. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures). www.JagDocs.com

Some variation in the illustrations may occur, but the essential information is always correct.

1. Disconnect the battery ground cable.

Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

3. Refer to: Timing Cover (303-01C Engine - V8 5.0L Petrol, Removal and Installation).

4.
5. CAUTION: Only rotate the crankshaft clockwise.
Install the special tool.

Special Tool(s): 303-1447