torque JAGUAR XFR 2010 1.G Repair Manual

Installation
1. Torque: 11 Nm























2. CAUTIONS:


Make sure that the mating faces are clean and free of
foreign material.


Apply a continuous bead of silicone gasket sealant
(Loctite 5999) as shown on the illustration. The application
of the sealant must be 4mm diameter. Install the
component immediately after applying the sealant without
smearing the sealant.


NOTE: New units must be configured using the
Programmable Module Installation Routine in the diagnostic
tool.
Torque: 11 Nm Apply a suitable amount of approved sealant to one
of the mating faces.

8. Torque: 25 Nm

Rear Drive Halfshafts -
Lubricants, Fluids, Sealers and Adhesives Published: 11-May-2011
Item Specification Constant velocity (CV) grease Optimal LN 584 LO Fill Capacities
Description Grams Grease for inner CV joint - all vehicles 140 Grease for outer CV joint - all vehicles 125 Torque Specifcations

NOTE: Make sure that a new nut is installed.

Item Nm lb-ft lb-in Halfshaft outer constant velocity joint retaining nut 300 221 -

5. CAUTIONS:


Do not install the rear halfshaft fully at this stage.


Only install the rear halfshaft until the halfshaft
splines have past the halfshaft oil seal.







6. Remove and discard the halfshaft oil seal plutector.


7. CAUTION: Make sure that the rear halfshaft circlip is
installed correctly by pulling the halfshaft gently to make
sure it is engaged.














8. CAUTION: The final tightening of the suspension
components must be carried out with the vehicle on its
wheels.

Torque: 90 Nm

9.
















10.
11. CAUTION: Install the halfshaft nut finger tight.


NOTE: Do not fully tighten the locking nut at this
stage.













CAUTION: The final tightening of the suspension
components must be carried out with the vehicle on its
wheels.
Torque: 150 Nm













CAUTION: The final tightening of the suspension
components must be carried out with the vehicle on its
wheels.
Torque: 55 Nm

Install the brake disc.

















Torque: 103 Nm

15.
















16. CAUTION: Do not use air tools to install the nut.
Failure to follow this instruction may result in damage to
the component.
Torque: 300 Nm











Check and top-up the differential case.














17.
Install the LH rear wheel and tire.

Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

3. NOTE: Left-hand shown, right-hand similar.
















4. NOTE: Left-hand shown, right-hand similar.
5. NOTE: Left-hand shown, right-hand similar.
Torque: 58 Nm

6. NOTE: Left-hand shown, right-hand similar.

Secure the bottom arm of the anti-rattle spring
under the bottom anchor bracket of the caliper.
Compress the upper spring arm into the correct
position, under the upper anchor bracket, whilst
retaining the logo plate.
Using the screw-driver, tap the central locating tag
into the locked position.
















7. CAUTIONS:


Always plug any open connections to prevent
contamination.


Make sure new sealing washers are installed.

NOTES:


To prevent the loss of brake fluid, using the special
tool apply the brake pedal and set to 40mm ( 1.6 in ) below
the rest position.


Left-hand shown, right-hand similar.
Torque: 42 Nm www.JagDocs.com

Published: 11-May-2011
Front Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Brake Disc Vehicles With: High Performance Brakes
Removal and Installation

Removal


CAUTION: Brake discs must be renewed in pairs.


NOTE: Removal steps in this procedure may contain installation details.


1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.

2. Refer to: Brake Pads - Vehicles With: High Performance Brakes (206-03B Front Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol,
Removal and Installation).

3. Torque: 115 Nm 4.
Remove the 2 clips.
Clean the components mating faces.













Installation 5. Repeat the above procedure on the opposite side.

1. To install, reverse the removal procedure.