bonnet JAGUAR XJ6 1994 2.G Workshop Manual

Terrn(s) Abbreviation Definition Previously used (if applicable) terrn(s1 (or Eng-
lish Eauivalent)
Hall Effect process
where current is passed through a
small slice of semi-conductor material at the
same time as a magnetic field. Produces a
small voltage
in the semi-conductor
a fault currently present
in the system
hard fault
headlamp HL
Heated Oxygen Sensor
H02S electrically heated oxygen sensor which Lambda sensor, .- induces fueling corrections. HEGO, HOS
heavy
duty HD
Hertz (frequency)
HZ frequency, one cycle per second
High Mounted
Stoplamp HMSL
high tension (electrical) ht
hood bonnet
hose clamp hose clip
hour hour
h, hr
hydrocarbon HC
hydroplaning
I aquaplaning
X300 VSM Issue 1 August 1994 16

12.1.5. ABS Components
Hydraulic Module
The hydraulic module is located under the bonnet adjacent
to the engine compartment firewall. It is secured within a steel mounting bracket at three securing points. All elec- tronic and power connections are made through one cable
loom connect ion.
The hydraulic pump
(1 Fig. 1) is a reciprocating two-circuit pump in which one brake circuit is assigned to each pump
circuit. The pump supplies adequate pressure and volume
supply to the brake circuits under anti
-lock braking condi- tions. The pump is driven by and electric motor (2 Fig. 1). The
pump housing incorporates two low pressure accumulators
and damping chambers for each brake circuit.
A modulator valve block
(3 Fig. 1) incorporates the ABS CM or ABS / TC CM (4 Fig. 1). Vehicles with traction control are
fitted with a throttle position actuator (5 Fig. I), which is an
electrical device controlled by the ABS 1 TC CM.
Valve blocks on vehicles without traction control comprise
six solenoid valves, three normally open (NO) inlet valves
and three normally closed
(NC) outlet valves. These valve
blocks have three outlet ports. Valve blocks on vehicles with
traction control comprise nine solenoid valves, four
NO inlet valves,four NC outlet valves and one special isolating valve.
Fig. 2 shows a hydraulic module for vehicles with traction
control. The valve block (2 Fig. 2) has four outlet ports (Indi- vidual control of the driven wheels).
A BS CM, A BS / TC CM
The ABS CM or ABS TCI CM locates beneath the modulator
valve block and is secured by
two screws. The CM houses
the solenoids which operate the inlet and outletvalves of the
modulator valve block. When fitted, the valve stems locate
in the
CM mounted solenoids. There is no electrical connec- tion between the CM and the modulator valve block. Fig. 3 shows an ABS TC 1 CM having nine solenoids.
The
CM functions include the following:
0 Providing control signals for the operation of ABS
and traction control solenoid valves
0 Calculating wheel speed from voltage signals trans- mitted by the wheel speed sensors
0 Monitoring of all electrical components
0 On Board Diagnostics (OBD): storage of possible fail- ures in a non-volatile memory.
The signals from the four wheel speed sensors are indepen
- dently processed by the ABS CM or ABSITC CM, calculating
numerical values which correspond directly to the wheel
speed. These values are converted into control signals for
pressure modulation during ABS control.
The ABS and traction control
are continuously monitored,
whilst the ignition is on,for possiblefaults and interruptions.
If a fault is detected, the module deactivates the ABS and
indicates this by lighting the ABS warning lamp. In a fault
condition, conventional braking is unaffected. The module
stores fault codes in a non
-volatile memory which can be
read via the OBD link.
U: For electrical diagnostic information on the ABS I traction control systems, refer to EDM, Section 12. Fia.
1
Fia. 2
Fin. 3 I
J70286
Issue 1 August 1994 X300 VSM

rl Electrical
15.12 RELAYS
15.12.1 €@ne Compartment Relays, General Description
05
04
03
02
Fig. 1 Engine Compartment Relays
In order to locate individual relays,
Fig.1, showing all relay locations within the engine compartment, is to be read in
conjunction with the following table. The numbers indicating the relays on the illustration correspond to the numbers
in the right
-hand column. To remove and refit individual relays, open the bonnet, locate the faulty relay, unplug and
renew.
Issue 1 August 1994 32 X300 VSM