service JEEP CJ 1953 Service Manual

Fl

EXHAUST
EMISSION
CONTROL
SYSTEMS
IMPORTANT
NOTICE

The
Exhaust
Emission Systems covered
in
this publication
meet
State and

Federal
requirements for hydrocarbon and carbon
monoxide
emissions.

To
assure continued proper operation,
these
systems
must
be
inspected

regularly,
parts must be replaced
at
factory-recommended intervals and
engine

tune-up services performed at intervals specified in the
Exhaust
Emission
Con­
trol
System Maintenance charts.

For
the
above
reasons,
these
systems
must not, under any circumstances,
be

altered
to anything other than
required
specifications provided in this publication.

Further,
the
Exhaust
Emission
Control
System, or any
of
its components, must
not be physically altered or modified in any respect.

DHTfl
TAG

For
the serviceman's guidance, each vehicle equipped with exhaust emission

control
will
have data
tag
permanently affixed
to the
radiator shroud—-in
example:

VEHICLE
EMISSION
CONTROL
INFORMATION
MODEL
F4-134
C.I.D.

•
ENGINE
AT
NORMAL
OPERATING
TEMPERATURE

•
LIGHTS
AND
ALL
ACCESSORIES OFF

•
IDLE
MIXTURE
. . .
LEAN
BEST
IDLE

•
IGNITION
TIMING
0*
(TDC)
•
SPARK
PLUG
GAP
. . . .030

•
DWELL
...
42* (.020
POINT
GAP)
•
IDLE
SPEED
. . .
700-750 RPM
TRANSMISSION
IN
NEUTRAL
DURING
TUNE
UP

SEE SERVICE MANUAL
FOR
ADDITIONAL INFORMATION
THIS VEHICLE CONFORMS
TO U.S.
DEPT.
OF
H.E.W.
REGULATIONS APPLICABLE
TO
1971 MODEL YEAR NEW MOTOR VEHICLES

Jeep
CORPORATION
14401

Important:
Always refer
to
the data tag when checking or re-adjusting ignition

timing,
idle speed, and idle mixture. 148

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

Fl
EXHAUST
EMISSION
CONTROL
SYSTEM

Contents

DAUNTLESS
V-6
ENGINE
SUBJECT
PAR.

GENERAL
.F2-1
HEATED
AIR
SYSTEM.
. F2-2
Testing
Thermo
Air
Cleaner
F2-4
Positive
Crankcase
Ventilation
Valve.
. . .F2-6

Vacuum
Motor Replacement . .F2-8
Air
Cleaner Sensor Replacement F2-9
Replacement Procedures F2-7

AIR
PUMP
.F2-10

AIR
FILTER.
F2-11

AIR
DELIVERY
MANIFOLD.
F2-12

AIR INJECTION TUBES.
F2-13

ANTI-BACKFIRE
VALVE..
.F2-14
ENGINE COMPONENTS
.F2-15
MAINTENANCE
.F2-3
Carburetor
F2-16, F2-17

Distributor
F2-18

Anti-Backfire
Valve . . F2-19
Check
Valve..
F2-20

F2-1.
GENERAL
—V-6
Engine

The
Dauntless V-6
engine
Exhaust
Emission
Con­

trol
System consists of a belt-driven air pump

which
directs compressed air through connecting
hoses
to a steel distribution manifold into stainless steel injection
tubes
in the exhaust port adjacent
to each exhaust valve.
This
air, with its normal
oxygen
content, reacts with the hot but incom­
pletely burned exhaust
gases
and permits further combustion in the exhaust port or manifold.

The
Exhaust
Emission System on V6-225
engines

limits
the hydrocarbon and carbonmonoxide emis­sions from the exhaust system. The system includes

an
engine
designed for low emissions and lean
carburetor
calibration at idle and part throttle.

The
lean carburetion is possible because of the
heated air system that is part of the Emission
System.
See Fig. F2-2.
With
the heated air system
operating, inlet air temperature is around
115°F.
[46°C],
after the first few minutes of operation.

This
makes the use of lean (hot weather)
cali­
bration
possible, and the vehicle
still
responds and

drives
well in cold weather.

The
engine
has a "ported"
spark
advance, with the

vacuum
take-off just above the throttle valve, so that there is no vacuum advance at closed throttle,
but there is vacuum advance as
soon
as the throttle is opened slightly. To reduce emissions at idle and
at lower
engine
speeds, the
engine
timing is such
that the distributor
will
not have centrifugal ad­
vance until about 900 RPM.
F2-2.
HEATED
AIR
SYSTEM

The
heated air system on late model V6 engines,
consists of a manifold heat collector, a heated-air
SUBJECT
PAR.

Air
Pump F2-21
Intake
Manifold F2-22
Carburetor
Air Cleaner F2-5, F2-23

REMOVAL PROCEDURES
F2-24
Air
Pump. F2-25
Anti-Backfire
Valve..
. . .F2-26
Air
Distribution Manifold,

And
Air Injection Tubes F2-27

REQUIRED
EQUIPMENT..
. F2-28
REPLACEMENT
PARTS..
.F2-29

WARRANTY
F2-30
DIAGNOSIS GUIDE
F2-31
MAINTENANCE CHART.
F2-32
GENERAL
SPECIFICATIONS
F2-33

CARBURETOR SPECIFICATIONS.
.... .F2-34

DISTRIBUTOR SPECIFICATIONS
. .F2-35
SPARK PLUG GAP
F2-36
pipe, a adapter elbow and an air cleaner contain­ing temperature control doors operated by vacuum
through a temperature sensor. The heat
stove
is a
sheet
metal cover, shaped to and bolted on with
the right exhaust manifold. Air drawn in along the lower
edge
of the
stove
passes across the mani­
fold surface, picking-up heat. The heated air is
drawn
out from the front of the manifold, through
the heated air pipe and adapter elbow into the
snorkel
of the air cleaner.

The
temperature control air cleaner is designed to mix this heated air with cold air from under the
hood so that carburetor inlet air temperature aver­
ages
about
115°F.
[46°C.].
This
mixing is
done
by two air doors, a cold air door and a hot air door,

which
move
together
so that when the cold air door is closed, the hot air door is open and vice
versa.
Most of the time, both doors
will
be partially
open as required to control the temperature. When
the underhood temperature reaches about 135
°F
[57°C]
the cold air door
will
open wide and the
hot air door
will
close
tight See Fig. F2-3. Ob­ viously, if underhood temperatures rise above
135°F.
[57°C]
the air cleaner
will
no longer be
able to control temperatures and the inlet air tem­

perature
will
rise with underhood temperature.
The
temperature doors are moved by a diaphragm
type vacuum door. When there is no vacuum pres­ ent in the motor, the diaphragm spring forces the
cold air door open and the hot air door closed.

Whenever
the
engine
is running, the amount of
vacuum
present in the vacuum motor depends on
the temperature sensor in the air cleaner which is located in the vacuum line
between
the intake
manifold and the vacuum motor. In the sensor, a 149

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

F2

FIG.
F2-2—DAUNTLESS
V-6
ENGINE
EXHAUST
EMISSION
HEATED
AIR
SYSTEM
1—
Air
Cleaner 4—Adapter
Elbow
and Hose
2—
Vacuum
Motor 5—Manifold Heat Collector
3—
Control
Damper and
Linkage
accelerating the
engine
hard
will
cause the vacuum
level in the intake manifold and in the vacuum motor to drop. Whenever vacuum drops
below
5 inches [12,7 cm.] the diaphragm spring
will
open

the cold air door wide in order to get the maximum

air
flow required for maximum acceleration.
F2-3.
MAINTENANCE

Efficient
performance of the
Exhaust
Emission
System is
dependent
on precise maintenance. In
addition to the heated air system, air pump, con­ necting
hoses
and tubes, it is essential that the

carburetor
and ignition distributor be properly ad­
justed to specifications listed at the end of this section.

Road
test
is a factory-recommended optional serv­
ice every
6,000
miles
[9,600
km.] to evaluate
overall
performance.

The
following procedure is recommended to assist

in
diagnosing performance and/or emission level problems that are peculiar to Controlled Combus­
tion Equipped vehicles.

F2-4.
Testing Thermo
Air
Cleaner Operation
Since
failure of the air cleaner
will
generally result

in
the snorkel cold air door staying open, failure
will
probably go unnoticed in warm or hot weather.
In
cold weather, however, owners
will
complain of
leanness, hesitation, sag, surge or stalling. When any
type
of lean operation complaint is received, always

test
the heated air system for proper functioning
before
doing any work on the carburetor.

Note:
Always perform checks in the same order
as listed
below.
151

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

F2

FIG.
F2-4—HOT
AIR
DOOR
OPEN

1—
Linkage

2— Motor
3—
Air
Cleaner
4— Sensor 5—
Temp
Sensing Spring
6—
Air
Bleed Valve 7—
Hot
Air Pipe 8—
Diaphragm
Spring
9—
Diaphragm

10—
Control
Damper
11—
Air
Inlet
12—
Vacuum
Chamber
13—
Snorkel
Tube
To
perform the thermometer check, proceed as
follows:
1. Start
test
with air cleaner temperature below
85°
F.
[29.4°
C.]. If
engine
has been run recently, allow it to cool down. While
engine

is cooling, remove air cleaner cover and

install
a temperature
gage
next to sensor.

Reinstall
air cleaner cover. Do not install wing nut. Let car stand idle for
V2
hour or
more before proceeding to
step
2.
2. Start engine.
Cold
air door should
close
im­ mediately if
engine
is cool enough. When cold air door starts to open (in a few min­
utes), remove air cleaner cover and read
temperature
gage.
It must read 115° F.
[46°
C]
±20°.
3.
If cold air door
does
not start to open at
temperature indicated, temperature sensor is
defective and must be replaced.

F2-5.
Carburetor Air
Cleaner—Dry
Type

Every
24,000
miles
[38,400
km.] (or more fre­
quently in dusty territory) replace the air cleaner element. To do this, remove the wing nut and cover

from
the air cleaner housing.
Lift
out the air cleaner
element. Wipe the inside of the housing clean.
Service
the positive crankcase valve filler as out­
lined in paragraph F2-6. Make sure the air cleaner gasket is in
good
condition and properly located
on the carburetor flange.
Install
a new element, the cover and wing nut. Tighten the wing nut by hand.

Tighten
to make sure the air cleaner remains 153

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

F2

14043

FIG.
F2-6—REPLACING VACUUM MOTOR ASSEMBLY

A—Drill
VW
Hole
B—Sensor
Unit
Replacement Position
1—
Motor
3—Sensor
Unit

2—
Spot
Welds
4—Retaining
Strap
•e.
Drill
a
%j
inch [2,78 mm.] hole in snorkel tube

at
point
"A"
as shown in Fig.
F2-6.
f.
Use the motor strap retainer and the
sheet
metal

screw
provided in the motor replacement kit to secure the retainer and motor to the snorkel tube.
g. Make sure the screw
does
not interfere with the
operation of the damper assembly. Shorten screw
if
required.

F2-9.
Replacement
of Air
Cleaner Sensor

a.
Remove two sensor retaining clips by
prying.
See

Fig.
F2-7.

b.
Pull
vacuum
hoses
from sensor.

c.
Note
carefully the installed position of the sensor so that you can install new sensor in same position.

Then
remove sensor.

d.
Install
sensor and gasket assembly in air cleaner

m
same position as noted in
step
c.
This
is to eliminate the possibility of interference with the air

filter
element.
e.
Install
sensor retaining
clip,
meanwhile support­
ing
sensor at B around the outside rim to prevent 14042

FIG.
F2-7—REPLACING SENSOR ASSEMBLY

1—Sensor
Retaining
Clip
damage to the temperature sensing spring. See

Fig.
F2-7.

f.
Reinstall
vacuum hoses.

F2-10.
AIR
PUMP
The
air injection pump is a positive displacement
vane type which is permanently lubricated and
requires
no periodic maintenance.

The
pump contains an integral relief valve which
controls the
air
supplied to the
engine
exhaust ports

during
high speed operation to limit maximum exhaust system temperatures.

F2-11.
AIR
FILTER
The
air injection system draws clean air from the
carburetor
air filter through an inlet hose, into the

air
pump and from the pump through two
outlets
(one for each cylinder head).

F2-12.
AIR
DELIVERY MANIFOLD

The
air delivery manifolds constructed of cold
rolled
steel with a zinc plating, distribute the air

from
the pump to each of the air delivery tubes in

a
uniform manner.

Two
check valves are included to prevent the
reverse
flow of exhaust
gases
to the pump should
the pump drive
fail.
This
reverse flow would dam­
age the air pump and connecting hose.

F2-13.
AIR
INJECTION TUBES
The
air injection tubes of stainless steel are in­ serted into machined
bosses
of the cylinder head.

The
tubes project into the exhaust ports directing
air
into the vicinity of the exhaust valve stem.

F2-14.
ANTI-BACKFIRE VALVE
The
anti-backfire valve is used to provide a "gulp" of air into the
engine
induction system during
rapid

throttle opening and subsequent closure.
During
rapid
throttle closure, the valve
opens
for approxi­
mately one (1) second and bleeds air into the
intake
manifold through a fitting in the carburetor.

Its
function is to bleed an adequate amount of

air
below the carburetor throttle plate to compen­ sate for the
overrich
fuel mixture normally inducted
into the combustion chamber during
rapid
throttle

closure.

Filtered
air from the pump is provided to the
anti-backfire
valve by means of a connecting hose.

An
exhaust system backfire
will
result if the valve

fails
to function properly.

F2-15.
ENGINE COMPONENTS
The
following item varies in design or specifications

from
those
on vehicles not equipped with the Ex­

haust
Emission
Control
System.

F2-16.
Carburetor

Check
carburetor number for proper application. Specifications are listed in this section.

Proper
carburetor idle mixture adjustment is im­ perative for
best
exhaust emission control.

The
idle adjustment should be made with the en­
gine
at normal operating temperature, lights and accessories off and the air cleaner in place.
Adjust
155

F2
EXHAUST EMISSION CONTROL SYSTEMS
the throttle
stop
screw to idle the
engine
at 650
to 700 rpm.

F2-17. Carburetor Idle Setting
The
"Lean
Best
Idle"
Method of Idle Setting is as
follows:

a.
Any scheduled service of ignition system should
precede this adjustment

b.
Connect tachometer to engine.

c.
Warm
up
engine
and stabilize temperatures.

d.
Adjust
engine
idle to speed desired, using throt­
tle idle speed adjusting screw.
e.
Turn
idle mixture screws out (counterclockwise)

until
a
loss
of
engine
speed is indicated; then slowly
turn
mixture screws in (clockwise-leaner)
until
maximum speed (rpm) is reached. Continue

turning
in (clockwise) until speed begins to drop;

turn
mixture adjustment back out (counterclock­
wise-richer)
until maximum speed is just regained

at
a "lean as possible" mixture adjustment.

F2-18. Distributor
The
ignition distributor used with the
Exhaust
Emission
Control
System is the same as that used
on
engines
without
Exhaust
Emission
Control.
Check
the distributor cam dwell angle and point
condition.
Check
ignition timing and adjust to specifications shown on the last
page
of this section.

F2-19.
Anti-Backfire
Valve

The
anti-backfire valve remains closed except when
the throttle is closed rapidly from an open position.
To
check the valve for proper operation, accelerate
the
engine
in neutral, allowing the throttle to close

rapidly.
The valve is operating satisfactorily when
no exhaust system backfire occurs. A further check
to determine whether the valve is functioning can
be made by removing from the anti-backfire valve
the large
hose
which connects the valve to the

pump.
With
a finger placed over the open end of
the
hose
(not the valve), accelerate the
engine
and allow the throttle to close rapidly. The valve is
operating satisfactorily if a momentary air rushing
noise is audible.

F2-20.
Check
Valve

The
check valves in the lines to the air distribution manifolds prevent the reverse flow of exhaust
gases

to the pump in the event the pump should, for

any
reason,
become
inoperative or should exhaust

pressure
ever exceed pump pressure.

To
check this valve for proper operation, remove the air supply
hose
from the pump at the check

valve.
With
the
engine
running, listen for exhaust
leakage at the check valve which is connected to
the distribution manifold.

F2-21.
Air
Pump

Check
for proper drive belt tension with belt tension
gauge
W-283. The belt strand tension should be 60 pounds measured on the
longest
accessible span
between two pulleys. DO NOT PRY ON THE

DIE
CAST
PUMP
HOUSING. To
check the pump for proper operation, remove
the air
outlet
hose
at the pump.
With
the
engine

running,
air discharge should be felt at one of
the pump
outlet
openings. The pump
outlet
air
pressure,
as determined by the relief valve, is preset
and
is not adjustable.

The
air pump
rear
cover assembly, housing the pressed in inlet and discharge tubes, and the pres­
sure
relief valve are the only pump components
recommended for service replacement. These parts
are
to be replaced only when damaged as a result
of handling or in the event the relief valve was
tampered with.

F2-22.
Intake Manifold

Intake
manifold leaks must not be overlooked. Air
leakage at the intake manifold may be compen­
sated for by
richer
idle mixture setting, however, this
will
usually cause uneven fuel-air distribution
and
will
always result in
loss
of performance and
exhaust emission control. To check for air leakage
into the intake manifold, apply kerosene or naph­
tha,
on the intake manifold to cylinder head joints

and
observe whether any changes in
engine
rpm

occur.
If an air leak is indicated, check the mani­
fold to cylinder head bolt torque. The correct torque is 25-35 lbs. ft. [3,46 a 4,84 kg-m.]. If the

leak
is
still
evident,
loosen
the manifold assembly

and
torque-tighten the bolts evenly.
Start
from the center and use proper torque values. Replace the
manifold
gasket if the leak
still
exists.
Clean
both
mating surfaces and check for
burrs
or other ir­

regularities.

Always
torque the bolts evenly to the specified
torque value to prevent warpage.

F2-23.
Carburetor
Air
Cleaner
—Oil
Bath

Every
6,000
miles [9,600 km.] disconnect attach­

ing
hoses
and unscrew the wing nut from the top
of the air cleaner and lift it off the carburetor.

Lift
the cover and filter element off the oil sump.

Clean
the inside surface of the sump and
refill
to

indicated
oil level with SAE 40 or 50
engine
oil
above 32 F; SAE 20 below 32 F.
Wash
filter element in kerosene and
drain.
Reassemble the air

cleaner
and install on carburetor.

More
frequent cleaning and replacement are advis­ able when the car is operated in dusty areas or on

unpaved
roads. Accumulated
dirt
restricts air flow,
reducing
fuel economy and performance.

F2-24.
REMOVAL PROCEDURES
The
following paragraphs
give
the procedures for removing the major units of the exhaust emission
control
system and the required equipment needed.

F2-2S.
Air
Pump

Loosen
the air pump mounting bracket bolts. Re­ move the air pump air hose(s). Separate the air pump from its mounting bracket. At time of install­
ation,
torque tighten the air pump mounting bolts
to
30-40
lbs.-ft [4,15 a 5,53 kg-m.].
Adjust
the
belt strand tension to 60 pounds. 156

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

F2
F2-26.
Anti-Backfire
Valve

The
anti-backfire valve removal requires discon­ necting the
hoses
and bracket to
engine
attaching
screws.

F2-27.
Air Distribution Manifold and
Injection
Tubes

The
air distribution manifolds can be removed
from the cylinder heads without removing the

cylinder
head assemblies. Disconnect the air delivery
hose
from the pump at
the distribution manifold inlet (check valve).
Loosen the distribution manifold
tube
attaching nuts from the cylinder head and carefully work the
distribution manifold away from the cylinder head.

The
air injection
tubes
can be removed from the
cylinder
head with head on the
engine.
Insert
an easy-out through the
boss
opening on the

cylinder
head
into
the injection
tube
and twist
the
tube
out gradually. Some interference to re­ moval may be encountered due to normal carbon
build-up on the tubes. Injection
tubes
removed in
this manner should be replaced.
The
injection
tubes
used are all of the same diam­
eter and length.

F2-28.
REQUIRED EQUIPMENT

Each
station licensed to perform repair and main­ tenance on the Exhaust Emission Control System
must be equipped with that equipment necessary
for major
engine
tune-up analysis which shall in­ clude at least the following or equivalent:
Ignition Analyzer Oscilloscope
Ammeter
Ohmmeter
Voltmeter
Tachometer 2 Vacuum Gauges
Pressure
Gauge (0-10 psi.)

Cam
Angle Dwell Meter
Ignition Timing
Light

Engine
Exhaust Combustion Analyzer Compression Tester

F2-29.
REPLACEMENT PARTS

Parts
necessary to repair and/or maintain the Ex­
haust Emission Control System are available through any Jeep
SALES
CORPORATION
ware­
house.

F2-30.
WARRANTY
All
parts of the Exhaust Emission Control System
are
covered by the Manufacturer's
Warranty
as stated in the
Warranty
Service and 'Jeep' Quality
Maintenance Plan booklet. 157

F2
EXHAUST EMISSION CONTROL SYSTEMS
F2-3L
EXHAUST EMISSION CONTROL SYSTEM
DIAGNOSIS
GUIDE

Pump Noisy
Hoses Touching Other Parts of Engine or Body (Hood).

Note:
The Air Pump is not completely noiseless.

Under
normal conditions, pump
noise
rises in pitch as
engine
speed
increases. It is desirable to allow
for normal break-in wear of the pump prior to re­
placement for
excessive
noise.
Pump Seized
Replace pump.
-
do not pry on housing.
Leak
In Hose

Check
for leaks; using
soap
and water, tighten clamps or replace
hoses.

Pump Inoperative
Loose Belt — tighten belt
-

Filter
Plugged — replace.

Exhaust
Backfire

Check
for vacuum leaks — correct as necessary.
Check
anti-backfire valve — replace as necessary
Induction System Backfire

Verify
engine
timing and distributor dwell.
Verify
accelerator pump charge.

F2-32.
EXHAUST EMISSION CONTROL SYSTEM MAINTENANCE CHART

Efficient
performance of the Exhaust Emission very important that all of the maintenance require-

Control
System is
dependent
upon precise main-
ments
are performed with extreme care at the
tenance. As indicated in the following chart, it is specific interval indicated.
Thousands of miles* or

OPERATION
number of months whichever occurs first 2 6 12 18 24 30
Inspect engine-driven
belts
for condition and tension R R
Replace positive crankcase ventilation valve
(PCV)
R R

Check
for free operation of exhaust manifold heat control valve O O O O O

Clean
carburetor air cleaner — Oil Bath O O O O O
Replace carburetor air cleaner
element
— Dry Type O
Check
heated air system O O

Engine
tune-up O O

Check
engine
timing R O O O
Adjust
carburetor idle
speed
and mixture R O O O

Perform
factory-recommended road
test
for evaluation of overall performance and handling O O O O O

R
— Required Services O — Recommended Services

*
Miles Kilometers
2,000
—
3,200

6,000
—
9,600

12,000
—
19,200 18,000
—
28,800
24,000
—
38,400
30,000
—
48,000

F2-33.
GENERAL SPECIFICATIONS
Air
Pump Belt Tension 60 lb.

Rotor
Ring Screw Torque . 37 lb-in.
Housing Cover Bolt Torque 10 lb-ft. Speed Ratio, Air Pump to Engine
1
\i to 1

F2-34.
EXHAUST EMISSION CONTROL SYSTEM CARBURETOR SPECIFICATIONS

Make
Rochester Model Designation 2G Code Number
7027082
—
7041185

Choke
Manual
Number of Barrels 2

Throttle
Bore... \W [3,65 cm.]
Main
Metering Jet Production .051" - 60° [1,29 mm.]
High
Altitude — over
5000
ft .049" - 60° [1,24 mm.]
—
over
10,000
ft .047" - 60° [1,19 mm.]

Float
Level
Adjustment* 1%," [2,94 cm.]
Float
Drop Adjustment l%" [4,76 cm.]
Pump Rod Adjustment** 1%" [2,94 cm.]
Engine
Idle
R.P.M.
(In Neutral) 650 to 700

Initial
Idle Speed-screw
setting
3 turns in

Initial
Idle Mixture-screw
setting
2 turns out
Dash
Pot Setting. Y%w [3,75 mm.]
*From
air horn gasket to top of float at toe.

**From
air cleaner ring to top of pump rod.
158

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

F2
F2-35.
EXHAUST EMISSION CONTOL SYSTEM
DISTRIBUTOR SPECIFICATIONS

Distributor:
Make
Delco-Remy Prestolite Prestolite
Model...
1110376
IAT-4501 or IAT-4502 IAT-4502A

Breaker
Point Gap .016"
[0,406
mm.] .016"
[0,406
mm.] .016"
[0,406
mm.]

Breaker
Arm Tension 19 to 23 oz. [538 a 652 gr.] 17 to 22 oz. [482 a 623 gr.] 17 to 22 oz. [482 a 623 gr.]

Cam
Angle. 29° to 31° 29° + 3° 29° ± 3°

Max.
Auto Advance
(Crankshaft
Degrees). 13° to 15° at 1,950 rpm. 16° (& 1800 rpm. 21° @ 1800 rpm.
26°
@
4200
rpm. (Max.) 32° @
4200
rpm. (Max.)

Max.
Vac. Advance
(Distributor
Degrees) 8° 8° 8°
Condenser Capacity. .18 to .23 mfd. .25 to .28 mfd. .25 to .28 mfd.

Timing:
Crankshaft
5°
(BTC)
@ Idle 5°
(BTC)
© Idle 0°
(TDC)
© Idle

Mark
Location Crankshaft Pulley Crankshaft Pulley Crankshaft Pulley

Firing
Order
1-6-5-4-3-2 1-6-5-4-3-2 1-6-5-4-3-2

F2-36.
SPARK PLUG
GAP

Spark
Plug Gap. .035"
[0,889
mm.]

IMPORTANT
NOTICE
The
Exhaust Emission Systems covered in this publication
meet
State and Federal
requirements for hydrocarbon and carbon
monoxide
emissions.

To
assure continued proper operation,
these
systems
must be inspected regularly,
parts must be replaced at factory-recommended intervals and
engine
tune-up services
performed at intervals specified in the Exhaust Emission Control System Maintenance
charts.

For
the
above
reasons,
these
systems
must not, under any circumstances, be altered
to anything other than required specifications provided in this publication.
Further,

the Exhaust Emission Control System, or any of its components, must not be physi­
cally
altered or modified in any respect.

DATA
TAG

For
the serviceman's guidance, each vehicle equipped with exhaust emission control

will
have data tag permanently affixed to the radiator shroud — in example:

VEHICLE EMISSION CONTROL INFORMATION MODEL V6-225 C.I.D.

•
ENGINE
AT
NORMAL OPERATING TEMPERATURE

•
LIGHTS
AND ALL
ACCESSORIES
OFF

•
IDLE MIXTURE
.. .
LEAN BEST IDLE

•
IGNITION TIMING
0*
(TDC)
*
SPARK PLUG
GAP 035
•
DWELL
. . . 30* (.016
POINT
GAP) •
IDLE SPEED
. . .
650- 700
RPM
TRANSMISSION
IN
NEUTRAL DURING TUNE
UP

SEE
SERVICE MANUAL FOR ADDITIONAL INFORMATION

THIS VEHICLE CONFORMS
TO U.S. DEPT. OF H.E.W.
REGULATIONS APPLICABLE
TO
1971
MODEL YEAR
NEW
MOTOR VEHICLES
Jeep
CORPORATION
14400
NOTE:
The
above
tag applies to vehicles equipped with Distributor Model
IAT-4502A.

On
vehicles equipped with Distributor Models
1110376,
IAT-4501 and IAT-4502 the tag is the same

except
that Ignition Timing is 5°
T.D.C.

Always
refer to the data tag when checking or re-adjusting ignition timing, idle speed, and idle mixture.
159

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

COOLING
SYSTEM

Contents

SUBJECT
PAR.

GENERAL
.G-l Antifreeze Solutions. .G-l6
Cylinder
Block.
..................
.G-8

Draining
Cooling System............... G-3

Engine
Overheating..
.................
.G-19
Fan
Belt.
......... .........
.G-18
Filling
Cooling System.................
G-2

Inhibited
Coolant Solution .G-l7

Temperature
Sending Unit.
...........
.G-l0

Thermostat
.........................
G-9

RADIATOR
.G-5
Radiator
and Heater Hoses.............
G-7
SUBJECT
PAR.

Radiator
Pressure
Cap.................
G-4

Radiator
Removal and Replacement..... G-6

WATER
PUMP.
. . .G-ll
Water
Pump Disassembly. .............G-13

Water
Pump Inspection.
..............
.G-12

Water
Pump Reassembly.
.............
.G-14

Water
Pump Removal and Replacement. .G-l5

SERVICE
DIAGNOSIS.
.G-20

SPECIFICATIONS
. .G-21

ANTIFREEZE
CHART.
..... ... .G-22

G-l. GENERAL
a.
The satisfactory performance of the Hurricane

F4
engine
is controlled to a great
extent
by the proper operation of the cooling system. The
engine

block is full length water jacketed which prevents
distortion of the cylinder walls. Directed cooling
and
large water holes, properly placed in the cylin­
der head gasket cause more water to flow past the
valve
seats
(which are the
hottest
parts of the

block)
and
carry
the heat away from the valves, giving positive cooling of valves and seats.

Minimum
temperature of the coolant is controlled by a thermostat mounted in the
outlet
passage of
the engine. When the coolant temperature is below
thermostat-rated temperature, the thermostat re­ mains closed and the coolant is directed through
the radiator-bypass
hose
to the water pump. When the thermostat opens, coolant flow is directed to
the top of the radiator. The radiator dissipates the
excess
engine
heat before the coolant is recirculated
through the engine.
The
cooling system is pressurized. Operating pres­
sure
is regulated by the rating of the radiator cap

which
contains a relief valve, b. The Dauntless V-6
engine
efficiency and per­formance is controlled to a great
extent
by proper
operation of the cooling system. The cooling system

does
more than cool the engine. It also directs
the flow of coolant to provide the
best
operating
temperature range for each part of the engine.

In
the Dauntless V-6
engine
coolant is forced by
the water pump into two main passages that run the length of the block on each side (Fig. G-l).
FIG.
G-1—COOLANT
FLOW
THROUGH
THE
DAUNTLESS
V-6
ENGINE

161