service JEEP CJ 1953 Service Manual

'Jeep*
UNIVERSAL
SERIES SERVICE
MANUAL

D
©—P3
10789

FIG.
0-8—STEERING TIE ROD
1—
Cotter
Pin 6—Lockwasher

2—
Nut 7—Left Tie Rod

3—
Dust
Cover
8—Lubrication
Fitting
4—
Left
Socket 9—Left Socket (For Right Tie Rod) 5— Nut 10—Right Tie Rod 11—
Right
Socket

12—
Bolt

13— Tie
Rod
Clamp

0-17.
Tie Rod
Removal
First
disconnect and remove the steering tie rod

from
the bellcrank. Refer to Fig. O-l. The tie
rod
can then be removed by removing the cotter
pins and
nuts
at the
ends.
To remove the tie rod

from
the steering knuckle arms, use a puller or
expansion
fork.
Then
separate
the
joint
seals
and
fittings,
if
necessary.
The tie rod
sockets
can be
removed by loosening the
nuts
on the clamp bolts
and unscrewing the
sockets
from
the tie rod
tubes.

Refer to Fig. 0-8. When installing the
components

of
the steering linkage, new
seals
should be in­ stalled as
necessary.
All
nuts
should be torqued 38
to 42
lb-ft.
{5,2 a 5,8
kg-m.],
and new cotter pins
installed.
If the bellcrank was removed, the
steer­

ing
bellcrank nut should be torqued 70 to 90
lb-ft.
[9,7
a 12,4
kg-m.].

0-18.
Steering
Bellcrank
Service
Refer to Fig. 0-9.
The
assembly
and adjustment of this unit is ex­
tremely important; the information outlined below must be
followed
carefully whenever servicing the
bellcrank
assembly
on late model vehicles.
A
service kit
Part
No. 991381 containing the
bell­

crank shaft, bearings,
seals,
bolt, nuts, and
washer
is
available for servicing this
assembly.
Be certain that all
parts
are installed in their proper position.
When assembling the parts, be
sure
the new
bear­

ings in the bellcrank are positioned
Y%"
[3,175 mm.]
below the
surface
of the bellcrank
face
as shown. The
bearings
have
a
light
press"
fit that
will
hold
them in
place
after locating them in the proper
position.
Finally, when installing
washers,
the
chamfer on the
washer
must be installed toward
the bellcrank.

After
completing the
assembly,
and before attach­

ing
the connecting
rods
to the bellcrank levers,
make
your
final
adjustment to the
assembly
as

follows:

a.
With
the W [11,113 mm.] diameter clamp bolt
loosened, adjust the locknut on the end of the
bell­
crank shaft
until
the bellcrank just
rotates
freely

without
a bind.

Note:
On early model vehicles using bellcrank kit

Part
No. 920556, torque the bellcrank shaft nut
(Fig.
O-l #14) 70 - 90
lb-ft.
[9,7 a 12,4
kg-m.].
319

STEERING
SYSTEM

FIG.
0-9—STEERING

BELLCRANK
ASSEMBLY

1— 5s'-18
Stollock
Lockout

2—
Plain
Washer

3— 7 us"-20
x
2 l2' Bolt

4—
71«
*-20
Stollock
Locknut
5—
Beilcrank
Support

6—
Special
Ground
Washer
7— Seal
8—
Bearing
9— Beilcrank
10— Beilcrank
Shaft

11—
Seals

12—
Bearings

13— } s *
b.
Torque the
Vfc"
[11,113
mm.] diameter elamp
bolt to
50-70
lb-ft. [6,9 a 9,7 kg-m.].

c.
Assemble the tie rod to the beilcrank lever,
making
sure to tighten the nut to the proper
torque value of 38 to 45 lb-ft. [5,2 a 6,2 kg-m.].

d.
Connect the drag
link
to the beilcrank arm,

adjust
the
ball
joint by screwing in the plug firmly against the
ball,
approximately 20 lb-ft. [2,8 kg-m.], then back off one quarter
turn
and lock

with
a new cotter pin.

0-19.
Beilcrank
Support
Bracket
Rivet
Replacement

The
procedure for replacing a rivet with a bolt
is as follows:

a.
Drill
a [4,76 mm.] pilot
hole
up through
the front rivet.

b.
Enlarge
the [4,76 mm.]
hole
with a %"
[8,73 mm.]
drill.

c.
Chisel
off the
bottom
rivet head and drive the

remainder
of the rivet upward and out, using
a
punch and hammer.

d.
Install
a %" [9,53 mm.] bolt and lock nut,
torque to
30-45
lb-ft. [4,1 a 6,2 kg-m] and stake
the nut.

e.
Clamp
a metal plate to the frame to protect
the radiator, then
drill
and remove the remaining two rivets, install bolts, lock nuts and torque as
specified.

O-20.
STEERING
COLUMN
AND
WHEEL SERVICE

Jeep
Universal
Series vehicles use a
one-piece
steer­
ing
shaft that is integral with the steering gear
assembly, as shown in Fig. 0-2. Alignment in­
structions in paragraph 0-4 apply.

0-21.
Steering
Wheel Removal •
Refer to Fig. 0-2.

a.
Carefully
pry the rubber horn cap from the housing slot.
b.
Remove steering shaft nut.

c.
Remove steering wheel and spring.

0-22.
STEERING GEAR SERVICE

Note:
The steering gear can be adjusted when the
gear is mounted in the vehicle by first disconnecting
the drag
link
from the steering arm. Refer to Par.
Q-5.
0-23.
Removal
of
Steering Gear
•
F4-Engine.

a.
Remove the directional signal unit from the steering column.

b.
Remove the steering column bracket attached
at the instrument panel.

c.
Remove upper section of the floor pan.

d.
Disconnect shift rods from the shift levers at
lower end of the steering column if applicable.

e.
Disconnect the horn wire at lower end of steer­
ing
gear assembly.

f.
Remove steering gear arm from the steering gear assembly.

g.
Remove
bolts
attaching the steering gear hous­
ing
to the frame.

h.
Remove the steering gear assembly by bringing

it
up through the floor pan opening.

•
V6 Engine.

a.
Remove oil pan
skid
plate.

b.
Remove
left
exhaust pipe.

c.
Disconnect connecting rod (drag
link)
from
steering gear arm.

d.
Disconnect steering gear assembly from frame.

e.
Remove steering wheel from steering column.
f. Disconnect accelerator linkage.
g.
Remove upper floor pan assembly.
h.
Disconnect directional signal switch.
i.
Jack-up
vehicle, and remove steering gear and
320

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

O
column assembly down through the floor pan open­
ing and out from under vehicle.
0-24.
Disassembly
of
Steering
Gear
Refer
to Fig. 0-2.

When
the steering gear arm is installed on early
production vehicles, the line across the face of the

arm
and the end of the shaft should be in align­ ment. On later production vehicles, blind splines
on the lever shaft and in the steering gear arm en­

sure
correct positioning of the arm.

a.
Remove the steering gear arm with a puller
C-3646.

Caution:
Do not use a hammer or
wedge
to re­
move
the steering arm from the shaft and lever.

This
can cause damage to the shaft assembly.

b.
Loosen the lock nut and unscrew the adjusting

screw
two turns.

c.
Remove the side cover screws and washers. Re­
move
the side cover and gasket.

d.
Remove lever shaft.

e.
Remove upper cover plate screws. Remove cam,
wheel tube, and bearing assembly from the housing.
f.
Clean
all parts with suitable cleaning solvent and wipe dry.

g.
After dismantling as outlined above is com­
pleted, inspect cam
grooves
for wear, chipping and
scoring,
also the
ball
races on the cam ends and the
separate
ball
cups. Existence of any of
these
condi­ tions indicates the necessity for parts replacement.

h.
Inspect the tapered stud mounted on the lever
shaft for flat
spots
and chipping. In the case of
either, replacement is usually advisable. Inspect the
lever shaft for wear and
test
the fit of the shaft in
the bushings.

i.
Inspect condition of the oil seal at outer end of
lever shaft and the bearing at top end of steering
column.

0-25.
Reassembly
of
Steering
Gear
e Refer to Fig. 0-2.
Reassemble all parts to wheel tube in reverse order
of dismantling. Assemble cam, wheel tube and
bearing
assembly in housing, seating the lower

bearing
ball
cup in the housing.
Note:
New plastic retainer type cam bearings are
now available for the Ross steering gears. The new
bearings replace, and are interchangeable with,
the lock ring type cam bearings on gears equipped

with
early type cams.
With
adjusting shims in place, assemble upper
cover and adjust the cam bearings.
Assemble lever shaft in housing and with gasket
in
place assemble the side cover and set adjusting

screw
for a minimum backlash of the studs in the
cam
groove, with the steering gear at the center
point of travel.
When
assembling upper bearing spring and spring
seat in jacket tube make sure that the spring seat
is positioned correctly. It must be installed with
the lengthwise flange down against the bearing and
not up inside of spring coil.

0-26.
Installation
of
Steering
Gear

a.
After the gear has been properly adjusted, as
outlined in Par. 0-5, install steering gear assembly
in
chassis in the reverse order in which it was re­
moved.

b.
After installing the assembly in the vehicle,

jack
up front of vehicle and place the front wheels
in
the straight ahead position.

c.
Temporarily install the steering wheel to locate
the mid-position of the steering gear. To locate the mid-position,
turn
the steering wheel as far to the

right
as possible and then
turn
in the
opposite
di­

rection
as far as possible, noting the total number
of turns.
Turn
the wheel back just ^ of the total movement to place the gear in mid-position.

d.
With
the steering gear in mid-position and the
wheels in the straight ahead position install steer­ ing gear arm on lever shaft with the
ball
end down.

When
installed the line across the face of the arm

and
end of shaft should be in alignment.

0-27.
Steering
Wheel
Installation
•
Refer to Fig. 0-2.

a.
Install
steering wheel and spring on shaft.

Align
scribe marks on shaft and hub of wheel.
b.
Install
steering shaft nut and torque 20 to 25
lb-ft. [2,8 a 3,4 kg-m.].

c.
Install
horn cap. Test horn.
321

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

P
BRAKES

SUBJECT
PAR

GENERAL.
. P-l
Brake
Maintenance P-5
Master
Cylinder.
P-2

Parking
Brake
P-3
Transmission
Brake
P-4

BRAKE SERVICE
.P-6 Bleeding Brakes P-7

Brake
Adjustments P-14

Brake
Hoses P-8

Brake
Shoe
Initial
Adjustment P-l9

Brake
Shoe Installation P-l8

Brake
Pedal Adjustment P-9

Hand
Brake.
P-10 Inspection P-17
SUBJECT
PAR

Brake
Shoe Removal P-l6

Master
Cylinder Reconditioned. . P-20

Parking
Brake
Adjustment
.P-l 1
Relining
Transmission
Brake
P-13

Relining
Wheel
Brake
P-l5

Transmission
Brake
Adjustment .P-12

Wheel
Brake
Units P-14

Wheel
Cylinder Reconditioning P-21

TROUBLESHOOTING
P-2 2 Squeaky Brakes P-23
Rattles in Brakes P-24

SERVICE
DIAGNOSIS.
P-25

SPECIFICATIONS
P-2 6

P-1. GENERAL
A
double-safety
hydraulic brake system in con­
junction with self-adjusting wheel brake units are
standard
equipment on all current production
'Jeep* vehicles. The
double-safety
brake system
Is
equipped with dual
stop
light switches that op­
erate independently of each other, thus eliminating
possible
stop
light failure. Service information for
self adjusting brakes starts with Par. P-14.
All
four-wheel-drive vehicles are equipped with a transmission brake that operates in the drive line

and
is mounted to the rear of the transfer case. Two-wheel-drive vehicles
(DJ-5,
DJ-6)
are equipped
with a hand-operated parking brake that operates at the rear wheels.

P-2.
Master Cylinder —
Double Safety-Brake System

The
master cylinder (cast integrally with the res­

ervoir)
is the compensating type. Refer to Fig.
P-2 and P-13.
Action by the brake pedal
moves
the master cylin­der piston which exerts pressure on the fluid in
the cylinder and lines. 12914

FIG.
P-l—DOUBLE SAFETY BRAKE SYSTEM —
LATE
MODELS 1— Stop Light Switch and Tee (Froat)
2—
Line
Tee (Front)

3—
Master
Cylinder (Dual System
4—
Brake
Pedal Assembly 5—
Brake
Hose
6—
Line
Tee
(Rear)
7—
Wheel
Cylinder (Left
Rear)

8— Proportioning Valve
(Early
Models)
9— —Stop Light Switch and Tee
(Rear)

10—
Wheel
Cylinder (Left Front)
11—
Front
Brake
Hoses
323

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

P The
standard parking brakes (Fig. P-3) consist of
cable-controlled linkage for applying the rear wheel

brake
shoes
mechanically. A single cable from the

parking
brake control lever is connected, by means of an equalizer, to cables leading to individual rear

brakes.
A lever attached to the secondary
shoe,

with a link acting against the
primary
shoe,
expands the
shoes
into
contact with the drums.
P-4.
Transmission Brake

The
transmission brake is mechanically operated
by a hand lever through a cable and conduit and is mounted at the rear output bearing housing on the
transfer case. The transmission brake and its
linkage are shown in Fig. P-4.
P-5.
Brake Maintenance
No brake can be
expected
to work well when grease
or oil is allowed to leak
into
the drum from the rear axle. Little braking friction can be obtained

between
brakes and drums when the surface is
covered with grease and oil. For this reason, take
care
not to over-lubricate wheel bearings, forcing

lubricant
past seals. Also, check condition of seals

if
leak is suspected or whenever brake drums

are
pulled.
Whenever
wheels
are removed, it is advisable to
wash the drums with a suitable solvent so that all
grease and dirt are removed. Linings with any
evidence of grease or oil on them should be replaced.
The
hydraulic system should be kept free of dirt

and
moisture.
Use only SAE standard J-1703 Hydraulic
Brake
Fluid.

Caution:
Keep mineral oils, gasoline, or kerosene
out of the system as
they
cause rubber cups to

soften,
swell, and distort, resulting in failure.
P-6.
Brake
Service

To
service the brakes,
follow
the procedure
below:

a.
Check the fluid level in the brake master cylin­
der.
See Lubrication Section, Par. B-40.
b. Check brake pedal adjustment. See Par. P-9.
c. Check brake pedal travel. If the pedal travels more than halfway to the floor, the brake system
must be checked and the self adjusting star wheel mechanisms checked for binding, also the brake
linings should be inspected as
they
may be badly

worn.
How much lining is
left
can only be deter­ mined by visually inspecting the linings. See Par.
P-l6 for relining brakes.

d.
If the brakes pull to one side after adjustment, check tire pressures. All tires must be inflated to recommended pressures to ensure even braking. If
the condition persists, examine the brake linings
for foreign material and clean as necessary. If clean­
ing
does
not correct the condition the linings should be replaced. If the side pull persists, check front
wheel alignment and balance.
e. Check the brake system for leaks by applying a steady pressure on the brake pedal. A leak in the
system
will
allow the pedal to "fall away". If the pedal "falls away" check for a leaking wheel cylin­
der.
Remove
wheels
and drums and carefully check
each cylinder. Also examine all lines and fittings.

Rebuild
or replace all wheel cylinders (Par. P-21)

if
one is
defective
as
they
are all probably in poor condition. If the leak has allowed brake fluid to get
on the linings, the linings
will
have to be replaced.
f. A
"spongy"
brake pedal indicates the pressure of air in the hydraulic system.
This
condition must
be corrected by bleeding the brakes. See Par. P-7.
g. Should the brakes
become
locked so that the vehicle cannot be moved, the brakes may be re­
leased by opening the bleeder screw on any one of the wheel cylinders. Before the vehicle is driven, correct the cause of the condition. The cause may
3
14 15 16 17 18
4
10796

1—
Cable
and Conduit
2—
Hand
Brake
Clip

3—
Hand
Brake
Bracket
4—
Hand
Brake
Handle Assembly 5—
Rear
Cap
6—
Drive
Gear
Bushing
7—
Driven
Gear

8—
Driven
Gear
Sleeve
FIG.
P-4—TRANSMISSION
BRAKE

9—Backing
Plate
10— Shoe and
Lining

11—
Lever
End Return Spring
12—
Brake
Drum
13— Bolt 14—
Rear
Companion Flange
15—
Washer

16— Nut 17— Propeller Shaft Flange Yoke
18—
Rear
Propeller Shaft
19—
Adjusting
End Spring
20—
Adjusting
Screw Bracket
21—
Operating
Lever

22—
Clevis

23—
Retracting
Spring
Clip

24—
Retracting
Spring
Link
325

p

BRAKES
be either a defective master cylinder or the use of
low grade brake fluid which has expanded because
of heat. Use standard duty brake fluid conforming to
SAE-J1703
specification.

P-7.
Bleeding
Brakes

The
hydraulic
brake system must be bled whenever

a
fluid line has been disconnected or air
gets
into the system. A leak in the system may sometimes
be indicated by the presence of a spongy brake
pedal.
Air trapped in the system is compressible

and
does
not permit the pressure, applied to the
brake
pedal, to be transmitted solidly through to
the brakes. The system must be absolutely free
from
air at all times. When bleeding brakes, bleed
at that wheel with the
longest
line from the master
FIG.
P-5—BLEEDING
BRAKES

1—Bleeder
Screw
cylinder
first, the next
longest
second, etc. During
the bleeding operation the master cylinder must
be kept at least %
full
of hydraulic brake fluid.

To
bleed the brakes, first carefully clean all
dirt

from
around the master cylinder filler plug. If
bleeder tank is used follow the manufacturers in­
structions.
Remove the filler plug and
fill
the master
cylinder
to the lower
edge
of filler neck.
Clean
off

all
bleeder connections at all four wheel cylinders.

Attach
bleeder
hose
and fixture to right
rear
wheel

cylinder
bleeder screw and place end of tube in a
glass jar, and submerged in brake fluid. Open the bleeder valve one-half to three-quarters of a
turn.

See
Fig.
P-5.
Depress the
foot
pedal, allowing it to return very
slowly. Continue this pumping action to force the
fluid
through the line and out of the bleeder
hose
which
carries with it any air in the system. When bubbles cease to appear at the end of the bleeder
hose, close the bleeder valve and remove the hose.
After
the bleeding operation at each wheel cylinder
has been completed,
fill
the master cylinder reser­
voir
and replace the filler plug.
Do not re-use the liquid which has been removed

from
the lines through the bleeding process because
of air bubbles and
dirt.

P-8.
Brake Hoses

a.
Hydraulic
lines (tubing and hose) are the means
of transmitting fluid under pressure between the master cylinder and the wheel cylinders.

Note:
On
some
vehicles a proportioning valve is
located in the
rear
brake line along the inside left
frame
side
rail.
The valve is not serviceable and
must be replaced as an assembly.

Should
replacement be necessary make certain the valve is properly positioned with the centerline of
the hex plug (in the bottom of the valve) in the
vertical
position. Refer to Fig. P-l.

The
hoses
are the flexible links between the wheels

or
axles and the frame or body. The
hoses
must

withstand
the fluid pressures without expansion
and
must be free to flex during spring deflection
and
wheel turns without causing damage to the
hose.

b.
Hydraulic
lines are subject to damage and
deterioration. Hoses should be inspected for cuts,

chafing,
cracks,
twists and
loose
frame supports.

Hydraulic
tubing should be inspected for signs of
leakage (due to faulty flares or
loose
connections);

restrictions
(due to dents or corrosion); and wear (due to friction against other metal parts). Always
use correct type and size of wrench on fittings.

Avoid
damage to female fittings by supporting fit­
ting with tube nut during removal of assembly.

c.
On fittings where gaskets are used, always use
a
new gasket. Copper gaskets take a set and may
not form a
good
seal if reused.

d.
When replacing hydraulic brake hose, attach
hose
to wheel cylinder and securely tighten hose,
then attach
opposite
end to frame fitting or tubing.
Avoid
twists in
hose
when assembling to frame fitting
or
tubing. Hold
hose
end securely with

wrench
while attaching tubing to hose. If
hose
end
clip
is used, make certain clip is assembled properly.

Check
for interference during spring deflection or
rebound and during front wheel turns.

e.
Check
for any possible contact between front

brake
hose
and inner sidewall of tire when the front
wheels are in maximum
turn
position.
Check
for sufficient but not excessive length of
hose
between
the clamp and the wheels by turning the wheels
from
one extreme
turn
position to the otherl
f.
Check
that there is no possibility of any contact between the
tail
pipe and
rear
brake
hose
under
all
operating conditions.
P-9.
Brake Pedal Adjustment

There
should always be at least W [12,7 mm.]
free pedal travel before the push rod
engages
the master cylinder piston.

This
adjustment is accomplished by shortening or 326

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

P
lengthening of the brake master cylinder eye bolt.

This
is
done
so the primary cup
will
clear the by­
pass port when the piston is in the off position,
otherwise the compensating action of the master

cylinder
for expansion and contraction of the fluid
in
the system, due to temperature changes,
will

be destroyed and cause the brakes to drag.

Note:
Some older 'Jeep' vehicles may
develop
side

movement
of the clutch and brake pedals resulting
from wear of the pedals, shafts, and bushings. One
way to
compensate
for this wear is to install a pedal

slack
adjuster kit,
Part
No.
921936.
FIG.
P-6—HAND
BRAKE
ADJUSTMENT

P-10.
Hand Brake

On
Model DJ-5 and DJ-6 vehicles the rear brake

shoes
are operated through cables and conduits to
form the hand or parking brake. A brake cable
equalizer and adjusting rod, Fig. P-6, is located directly back of the frame center cross member.

P-11.
Parking Brake Adjustment

•
Model DJ-5, DJ-6.

The
foot
brakes must be satisfactorily adjusted be­
fore attempting adjustment of the hand brake.

To
adjust the hand brake raise both rear
wheels

free of the floor.
Pull
up three
notches
on the hand

brake
lever and tighten the adjustment until the

rear
brakes drag slightly. Release the hand brake
lever and check the rear
wheels
for drag. The

wheels
must turn freely with the lever released.

P-12.
Transmission Brake Adjustment
The
transmission brake is located on the propeller
shaft at the rear of the transfer case, see Fig. P-4.
The
brake is operated by a cable connection from
the brake handle mounted on the instrument panel.

To
adjust the transmission brake, the following

sequence
should be followed:
Make
sure that the brake handle on the instrument
panel is fully released. Give due attention to the
cable and operating linkage to see that
they
do
not bind. If necessary free up the cable and
lubri­
cate it. Rotate the brake drum until one pair of the
three
sets
of
holes
are over the
shoe
adjusting screw

wheels
in the brake. Use the
edge
of the
holes
in
the brake drum as a fulcrum for suitable adjusting

tool
or a screwdriver, rotate each notched adjusting
screw by moving the handle of the
tool
away from
the center of the drive shaft until the
shoes
are
snug in the drum.
Back
off seven
notches
on the
adjusting screw
wheels
to secure proper running clearance
between
the
shoes
and the drum. Refer
to Fig. P-8.

P-13.
Relining Transmission Brake
Note:
The condition of the brake lining on the
transmission brake can be visually checked through
the adjusting
holes
in the brake drum.
FIG.
P-7—REMOVING
TRANSMISSION

BRAKE
DRUM

1— Tool W-172
2—
Adapter

3—
Brake
Drum
a.
To reline the brake
shoes
and make a major ad­
justment, first remove the four universal joint at­ taching nuts and lower the propeller shaft. Remove
the retracting spring clevis pin and the spring clip.
Remove the hug lock nut, the nut and washer from
the transfer case output shaft. Both the universal
joint companion
flange
and the brake drum may be readily removed by using puller Tool No. W-172

which
is illustrated in Fig. P-7. Remove the two

brake
shoe
retracting springs and the
shoes.

b. Clean all parts with a suitable cleaning solution

and
examine them for damage or wear.

Brake
shoes
may be distorted by improper lining
installation and the lining should be ground true
after installation on the
shoes.
For this reason it
is recommended that new or replacement
shoe
and
lining assemblies be installed.
c. To reassemble, first turn both adjusting screw

wheels
away from the center to "all off" position.
Place a light film of grease on the brake actuating

cam
and install the
shoes.
Install the black
shoe
re­

turn
spring next to the cam and the yellow spring next to the notch adjusting wheel screw. Place the
brake
drum and universal joint
flange
in position

and
install the transfer case output shaft washer,
nut and hug lock nut. 327

p

BRAKES

PIG.
P-8—TRANSMISSION
BRAKE
ADJUSTMENT
1—
Bail
Nut

2— s,6"
12,38 mm.I
Clearance

3—
Adjusting
Screw
d.
Rotate the
drum
until
one pair of holes in the

drum
are opposite the two adjusting screw wheels

in
the brakes. Use the
edge
of the holes as a

fulcrum
and
with
a suitable
tool
or screwdriver for

adjusting,
rotate the adjusting screw wheels,
mov­
ing
the handle of the
tool
away
from
the
drum
until

the
shoes
are snug in the
drum.

e.
Examine the brake operating cable to be
sure
that
it is not
worn
or damaged. Free it up thorough­

ly
and lubricate
it.
Make
sure
the operating handle

on
the instrument panel is
fully
released.
Adjust
the clevis on the brake end of the operating cable

until
the clevis pin
will
just go through the hole

in
the clevis and brake operating lever
without

slack
in the cable.
Tighten
the clevis
lock
nut.

f.
After
the cable is connected back off seven
notches on each adjusting screw wheel
which
will
give
the proper
running
clearance between the

lining
and the
drum.

g.
Reconnect the propeller shaft.
Install
retracting
spring
clip,
clevis pin and the cotter pin, also, in­

stall
the retracting spring
link
and spring.
h. The
position
of the brake operating lever, Fig.
P-8, must be correctly set. The
position
of this
lever
is determined by the adjustment of the cam or
brake operating
link,
which
spreads
the two
shoes.
The
operating
link
is adjusted by
means
of the

special
ball
nut to set the operating lever
with

[2,38
mm.] clearance between the closest
point

of
the lever and the brake backing plate.

i.
The
position
of
this
lever should be checked when

making
a major adjustment or when
relining
the
brakes and
if
found
incorrect readjust it to give this
clearance before adjusting the brake cable
clevis.

P-14.
Self-Adjusting
Wheel
Brake
Units
Self-adjusting
brakes are standard equipment on

all
late production
'Jeep'
vehicles.
The
wheel brake units consist of a support plate,

two
brake
shoes,
brake
shoe
return springs, self-

adjusting
operating parts, and a wheel
cylinder.
The
automatic adjuster continuously maintains

correct
operating clearance between the brake
lin­
ings
and the drums by adjusting the brakes
in
small

increments in direct
proportion
to
lining
wear. This
continuous
adjustment prevents gradual increase

in
the brake pedal
travel
as the
linings
wear. The
adjuster, therefore,
adds
the safety feature of
main­
taining
adequate
pedal reserve
during
the service

life
of the
lining.

After
the
lining
wears enough to require adjust­ment, the adjusting cable or
link
will lift
the lever

into
engagement
with
the next
tooth
of the
star

wheel
when the brake is applied. When the brake
is
released, the
shoes
return to the anchor. The
self-adjuster
utilizes
the movement of the brake

shoes
in a brake application to
actuate
the adjuster
lever.

This
action
will
repeat
on
subsequent
brake applica­

tions,
if
necessary,
until
the
shoe
to
lining
clearance
is
reduced to a
point
where the
shoe
movement

is
not enough to
cause
the cable to
lift
the lever

to
the next
tooth.

The
adjusting lever, adjusting screw assembly,

linkage
rods and lever crank parts are
left
hand
or
right
hand parts, NOT interchangeable, and
MUST
be kept
separated.

The
automatic adjuster on the brake system con­

sists
of an adjusting screw assembly, adjusting

lever,
two adjusting
links,
and a lever crank, (Fig.
P-10).

Note:
It is not
necessary
to remove the rear axle
shaft hubs to
perform
minor
brake service.

When
replacement of
oil
seals
is also required, hubs must be removed.

On
vehicles equipped
with
self-adjusting brake
assemblies, self-adjustment of the
front
wheel brakes
takes
place
during
reverse wheel brake ap­

plication
and the rear wheel brake adjustment
takes

place
during
forward
vehicle brake application.
P-15.
Relining
Wheel
Brakes

a.
When
necessary
to reline the brakes, the vehicle
should
be raised so that all
four
wheels are free.

b.
Turn
the brake
shoe
star
adjustment all the

way
in. Refer to Fig. P-12.

c.
Remove the wheels, hubs and drums,
which
will

give
access
to the brake
shoes
(Fig.
P-10, P-11).

d.
Install
Wheel
Cylinder
Clamps C-416 to re­
tain
the wheel
cylinder
pistons in place and prevent leakage of brake
fluid
while
replacing the
shoes.

P-16.
Brake
Shoe
Removal
•
Removing the Front Brake
Shoes.

•
Refer to Fig. P-10.

a.
Using
Tool
C-3785
or equivalent remove the
upper linkage rod and brake
shoe
return springs.
b.
Remove the brake
shoe
retainer, spring and pins.
c. Remove the anchor pin plate.
d.
Remove the
primary
and secondary brake
shoe

assembly
from
the support.

e.
Overlap the anchor
ends
of the
primary
and
secondary brake
shoes
and remove the adjusting
screw, adjuster lever,
lower
return spring, and
linkage
rods. 328

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

P

FIG.
P-9—WHEEL HUB OIL
SEAL
DRIVER
•
Removing the
Rear
Brake
Shoes.

•
Refer to Fig. P-ll.

a.
Using Tool C-3785 or equivalent remove the
upper linkage rod and brake
shoe
return springs.
b. Remove the brake
shoe
retainer, spring and pins.
c. Remove the anchor pin plate and tilt the brake

shoe
assembly out from the backing plate.

d.
On vehicles without a transmission brake,
spread the anchor
ends
of the primary and second­

ary
shoes
and remove the parking brake strut and
spring.

e. On vehicles without a transmission brake, dis­

engage
the parking brake cable from the parking
brake
lever and remove the brake assembly.
f. Overlap the anchor
ends
of the primary and
secondary
shoes
and remove the adjusting screw,
adjusting lever, lower return spring, and linkage
rods.
P-17. Inspection
Inspect the oil seals in the wheel hubs. If the con­
dition of any oil seal is doubtful, replace it. Install
the oil seal with an oil seal driver as shown in Fig.

P-9.

Brake
shoes
may be distorted by improper lining installation and linings should be ground true. For
this reason it is recommended that new or re­
placement
shoe
and lining assemblies be installed.
Using
brake drum micrometer C-3920 or equi­
valent, check all drums. Should a brake drum be rough and scored, it may be reconditioned by grinding or turning in a lathe. Do not remove more
than .030"
[0,762
mm.] thickness of metal .060" [1,52 mm.] overall diameter. If a drum is recon­
ditioned in this manner, either the correct factory-
supplied, oversize lining .030"
[0,762
mm.] must be
installed or a shim equal in thickness to the metal
removed must be placed
between
the lining and

shoe
so that the arc of the lining
will
be the same
as that of the drum.

If
it is found when
wheels
are removed that there
is brake fluid leakage at any of the wheel cylinders, it
will
be necessary to replace or recondition the
wheel cylinder (Par. P-21) and bleed the brake lines (Par. P-7).
Whenever the brake lining is replaced in one front
or one rear wheel, be sure to perform the same
operation in the
opposite
front or rear wheel, us­
ing the same brake lining part number. Otherwise, unequal brake action
will
result.
FIG.
P-10—STANDARD
FRONT
WHEEL
BRAKE

ASSEMBLY
WITH
LINK
TYPE
ADJUSTER 1—
Primary
Shoe
6—Lever
Plate

2—
Wheel
Cylinder
7—Linkage Rod (Upper)

3—
Secondary
Shoe 8—Screw
4—
Adjuster
Screw Assembly 9—Linkage Rod
(Lower)
5— Sleeve 10—Adjuster
Lever

P-18.
Brake
Shoe Installation

Refer
to Fig. P-10.

INSTALLING
THE
FRONT
BRAKE
SHOES

To
install the front brake
shoes
proceed as follows:

a.
Match a primary with a secondary brake
shoe
and
place them in their relative position on a

work
bench.

Note:
Primary
brake linings are color coded red

and
green. Secondary brake linings are color coded
white and green.
b. Lubricate the threads of the adjusting screw

and
install it
between
the primary and secondary

shoes.
The star adjusting
wheels
are stamped "R"

and
"L"
indicating thread rotation. The
left
front
brake
adjusting screw has right hand thread rota­
tion and the right front brake adjusting screw has
left
hand thread rotation. 329

'Jeep*
UNIVERSAL SERIES SERVICE
MANUAL

P
f. On vehicles without a transmission brake hold
the brake
shoes
in their relative position and
engage
the parking brake cable
into
the parking

brake
lever.
g. On vehicles without a transmission brake in­
stall
the parking brake strut and spring
between

the parking brake lever and the primary
shoe.

h.
Place the brake
shoes
on the backing plate and

install
the retainer pins, springs and retainers.

i.
Install the anchor pin plate.

j.
Install the lever and
sleeve
on the primary
shoe
then install the secondary return spring, then the
primary
return spring.

Important:
A
"L"
or "R" is located on the hex­

agon
side of the lever crank for identification. The
lever crank marked "R" applies to the primary
shoe
on the
left
rear brake assembly. The lever
crank
marked
"L"
applies to the primary
shoe
on
the right rear brake assembly.
k. Place the upper linkage rod in the
groove
of the
anchor pin and
engage
the hook of the link rod
into

the adjusting lever.

I.
Install the brake drum. Install the wheel and

tire
assembly.
m. Adjust the brakes as described
below.

P-19.
Brake
Shoe
Initial
Adjustment —

a.
Should wheel brake units have
been
disassem­ bled for any reason, an initial adjustment
MUST
be made
before
drum installation.

b.
When the brake parts have
been
installed in
their correct position, initially adjust the adjusting
screw assemblies to a point where approximately Y% [9,53 mm.] of threads are
exposed
between
the

star
wheel and star wheel nut.

Note:
Following the initial adjustment and final
assembly, check brake pedal height to ensure

brake
operation. Then drive the car in reverse and
FIG.
P-12—BRAKE SHOE ADJUSTMENT
1—
Star
Wheel
2—
Lever

3—
Screwdriver
4—
Brake
Adjusting Tool
forward,
making 10 to 15 brake applications prior
to road testing.
This
action balances the adjust­
ment of the four brake units and raises the brake
pedal.
c. Adjustment may be made manually by remov­ing the access
slot
cover and using a brake adjust­
ing
tool
or screw driver to rotate the star wheel
until
the wheel is in the locked position. To tighten, rotate the star wheel in the clockwise direction.
Then
back off the star wheel at least 15 to 20

notches
(clicks).

d.
To back off the star wheel on the brake, insert
ice pick or thin blade screw driver in adjusting screw
slot
to hold lever away from adjusting screw.

Back
off on adjusting screw until wheel and drum

turn
freely. Replace adjusting
hole
cover.

Caution:
DO NOT attempt to back off on ad­
justing screw without holding adjuster lever away from screw as adjuster
will
be damaged.
P-20. Master Cylinder Reconditioning —
Dual
System

Refer
to Fig. P-13.

DISASSEMBLY
a.
Remove the filler cap and empty all fluid.
b.
Remove the snap ring, push rod assembly, and
the primary and secondary piston assemblies. Air pressure applied in the piston
stop
hole
will
help
facilitate the removal of the secondary piston as­
sembly.
c. The residual check valves are located under
the front and rear fluid
outlet
tube
seats.

d.
The
tube
seats
must be removed with the
self-

tapping screws supplied in the repair kit to permit removal of the check valves. Screw the self-tapping
screws
into
the
tube
seats
and place two screw

driver
tips under the screw head and force the
screw upward as shown in Fig. P-14.
e. Remove the expander in the rear secondary cup, secondary cups, return spring, cup protector,
pri­

mary
cup, and washer from the secondary piston.
f. The primary piston, with the rubber cups in­ stalled, is supplied in the repair kit.

CLEANING
a.
After disassembly, immersion of all metal parts
in
clean brake fluid or a brake system cleaner is
recommended. Use air
hose
to blow out dirt and cleaning solvent from recesses and internal pas­

sages.
When overhauling a hydraulic brake unit,
use all parts furnished in the repair kit. Discard
all
old rubber parts.

b.
After cleaning, place
all"
hydraulic
system parts
on clean paper or in a clean pan.

INSPECTION
Inspect all other parts for damage or
excessive

wear.
Replace any damaged, worn, or chipped
parts.
Inspect hydraulic cylinder bore for
signs
of
scoring, rust, pitting, or etching. Any of
these
will
require
replacement of the hydraulic cylinder. 331