towing JEEP CJ 1953 Service Manual

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

u
MISCEIiLaNEOUS

Contents

SUBJECT
PAR.

Abbreviations
U-15
Extra
Equipment U-2

Front
Bumper Weight U-9
Governor
U-3

Governor
Adjustment U-4

Governor
Maintenance. U-6

U-1. GENERAL

Miscellaneous information included in this sectioi
includes coverage of extra equipment, special
tools,
torque specifications, and charts and tables.

U-2. EXTRA
EQUIPMENT

Much
of the utility of the
*
Jeep*
Universal
is due to
the extra equipment which has been designed to adapt it for farming and industry. The mainte­
nance and use of
some
of this equipment is out­
lined
in this section.

U-3.
Governor Assembly

The
Novi governor is supplied for models equipped

with
the F4 engine.
This
is a centrifugal type governor and is illustrated in Fig. U-2. Complete

installation
instructions are supplied with each
assembly. Adjustment and operating procedures

are
given below.

U-4.
Governor Adjustment

a.
Adjust the carburetor to obtain smooth
engine

idle at 600 rpm., then
stop
the engine.
b.
Check
throttle linkage to ensure maximum
throttle opening. Be certain that throttle and
governor linkage is free.

c.
Place the carburetor throttle in wide-open posi­ tion and
pull
the governor control handle out to
the last notch. Adjust the governor to bellcrank

rod
so that the linkage
will
hold the carburetor
throttle in wide-open position.

d.
Close the governor control and start the
engine

Again
pull
the control out to the last notch and

adjust
the length of the cable at adjusting yoke so
that the
engine
will
run at
2600
rpm. Close the

control
to recheck the linkage for free action and
to make sure the
engine
will
return to 600 rpm.
idle speed.

If
the
engine
runs faster than this speed,
loosen

the lock nut which locks the governor hand control
handle on the dash to the rod and back off the
handle until the carburetor idle speed adjusting

screw
bears on the stop. Tighten the lock nut.
In
the absence of electrical tachometer equipment,

engine
speed may be determined by the speedom­
eter. Safely
jack
up the
rear
wheels and be sure the front wheel drive is not
engaged.
When driving
the
rear
wheels in high or direct transmission gear,
the
speedometer
will
read from 13j^ to 15 mph. [21.6 to 24.0 kph.] at an
engine
speed of from 900
to 1000 rpm.
SUBJECT
PAR.

Heater
U-10 Miscellaneous Data U-16

Pintle
Hook 1X7
Special
Tools. U-ll
Torque
Specifications U-13, 14, 15

Standard
and Recommended Tools
j.
.U-12

U-5.
Novi Governor Operation /

The
Novi governor is directly belted to the F4

engine
as no clutch is provided to disconnect the
drive.

To
operate the vehicle
WITHOUT
governor con­
trol,
push the governor hand control all the way
IN
against the instrument panel.

To
operate the vehicle
WITH
governor control,

pull
the governor hand control handle out. The
hand
control has nine notched positions. Pulling the

control
out to the first notch
sets
the controlled

engine
speed at approximately 1000 rpm. and each successive notch increases the speed 200 rpm.

until
2600
rpm. is reached in the ninth notch. The

hand
control may be released by turning the han­ dle one-quarter
turn
in either direction.

When
the
engine
is being operated under governor

control
(hand control out) the controlled
engine

speed may be
exceeded
at any time by depressing
the
foot
accelerator in the conventional manner to
secure a greater carburetor throttle opening than
that determined by the governor hand control
setting.

U-6.
Governor Maintenance

The
belt tension may be adjusted by raising or
lowering the governor in the slotted
holes
in the mounting bracket. Keep the pulleys and belt free
of
dirt
and oil. Belt slippage
will
affect governor
operation and a tight belt may cause
rapid
wear
of the governor shaft and bearings. Adjust it to
allow Yi' [12,7 mm.] depression midway
between
the pulleys with thumb pressure.
There
is little wear of the internal parts for they
operate in oil. The governor housings are equipped

with
both
fill
and
drain
plugs and also with level

indicating
plugs.
Check
the oil level at each vehicle
lubrication
and change the oil each time the en­

gine
oil is changed using the same grade oil used

in
the engine.

Caution:
Do not
fill
the governor housing above
the level plug. Overfilling
will
prevent governor
control
and possibly cause damage to governor in­

ternal
parts. The capacity of
these
governors is two fluid ounces [59,15 cm3]. The filler plug is
also a vent which should be cleaned thoroughly at
each oil change to be sure that the vent operates.

U-7.
Pintle Hook

The
standard type pintle hook, Fig. U-1, affords a
safe, easy hitch for towing a
trailer
or other vehicle. 357

u

MISCELLANEOUS
U-16. MISCELLtflNEOUS DATA

DRAW
BAR
PULL

The
power plant of the 'Jeep* Universal is particularly well adapted to the great variety of ap­
plications. For higher speed highway use, and draw bar
pull
requirements for towing loads, the

full
engine
power is available; for power take-off shaft and pulley drive, the
full
engine
torque
(turning
effort) is available.

Draw
bar
pull
is the force exerted by a vehicle to tow a trailed load and is expressed in pounds.

For
continuous
agricultural
work, the maximum draw bar
pull
should be limited to 1200 pounds [544 kg.]. The 'Jeep' Universal is capable of much higher draw bar pulls than the 1200 pounds
approved for continuous service, which may be used for starting loads or towing loads for short
periods on
good
ground in which case a draw bar
pull
as high as 1800 pounds [817 kg.] may be
safely used.

Maximum
continuous draw bar pulls are most
often
encountered in plowing, disking and
har­

rowing
and it is in
these
applications that the owner should guard against continuously exceeding
the recommended limit.

The
approved limit of 1200 pounds [544 kg.] may be judged by the following operations which

nearly
approach this limit:

Operating
two 12 inch [30,5 cm.] plows at a depth of 6)4 inches [16,5 cm.] in dry clay loam.
Operating
a 7
foot
[2,13 meter] tandem disk at a depth of 4j^ inches [11,4 cm.] in
hard

winter
packed soil.

Operating
a 3-section spring
tooth
harrow at a depth of 5 inches [12,7 cm.] in soil which
has been previously disked.

It
is expected that, either on account of soil conditions or implement adjustments,
these
draw

bar
pulls
will
be exceeded. In
these
instances, tire slippage provides an inherent safeguard against
overloading. Do not add weight, other than the standard bumper weight, to increase draw bar
pull.