oil type JEEP DJ 1953 Manual PDF

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

FIG.
Q-5—REAR
WHEEL

ATTACHING
PARTS —
FLANGED
AXLE

1—
Brake
Backing Plate

2—
Retainer
Ring

3—
Unit-Bearing

4—
Oil
Seal
5—
Retainer
Plate 6—
Brake
Drum
7—
Cup
Plug
8—
Flanged
Axle Shaft
14284

Q-4. Checking
Front
Wheel Bearings

Raise
the front end of the vehicle with a
jack

so that the tires clear the floor.

Grip
the tire and
test
sidewise shake of the wheel.

If
bearings are correctly adjusted, shake of the
wheel
will
be just perceptible and wheel
will
turn

freely with no drag.

If
bearing adjustment is too tight, the rollers may

break
or
become
overheated. Loose bearings may cause
excessive
wear and noise.

If
this
test
indicates bearing adjustment is neces­

sary,
follow
the procedure given in Par. Q-5. Loose
bearings
will
cause sidewise shake that is evident

around
the entire circumference of the wheel. A shake that is evident only when gripping the
wheels
in
a plane parallel to the ground, but not evident

around
the entire circumference, probably indicates
looseness
in the steering linkage.

Q-5.
Front Wheel Bearing Adjustment
With
the vehicle on the
jack,
the following proce­

dure
should be followed to adjust the front wheel
bearings on four wheel-drive vehicles.
a. Remove the hub cap, snap
ring,
capscrews, and
washers that attach the driving
flange
to the hub.

b.
Using the
Front
Axle Shaft Drive Flange Puller

W-163,
pull
the driving flange.
c. Bend the lip of the nut lock washer so that the

locknut
and lock washer may be removed.

d.
Rotate the wheel and tighten the adjustment nut until the wheel binds.

Note:
Front
tire and wheel must be rotated by

hand
as the adjusting nut is
tightened
to ensure positive seating of the bearing.

Then
back off the adjusting nut about one-sixth
turn
making sure that wheel rotates freely without
sidewise shake.
e. Replace the lock washers and locknut. Bend
over the lock washer lip.
f.
Check
the adjustment (Par. Q-4). Reassemble the driving
flange
and hub cap. Make certain the
gasket is properly installed
between
the hub and
the flange.

•
Model DJ-5, DJ-6

On
two-wheel drive vehicles, remove the hub cap
and
the wheel retaining nut cotter pin. Rotate the
wheel and tighten the wheel retaining nut until the wheel binds.
Then
back off nut about one-sixth
turn
or more if necessary making sure wheel ro­

tates
freely without sidewise shake. Replace the cotter pin and hub cap.

Q-6.
Rear
Wheel Bearing Adjustment —

Flanged
Axle Shaft

Vehicles
equipped with the
flange
type
rear
axle
shaft require no wheel bearing adjustment. The flanged axle shaft is equipped with a single row,

pre-adjusted,
tapered roller unit-bearing capable of
accepting thrust in either direction. The unit-

bearing
adjustment is built in at the factory mak­
ing shimming or bearing adjustment unnecessary.

Refer
to Fig. Q-6.

Q-7.
Checking
Rear
Wheel Bearings —
Tapered
Axle

Raise
wheel on which adjustment is to be made
by placing a
jack
under the axle housing.
With
hands,
test
sidewise shake and in and out play
of the wheel. If bearings are correctly adjusted,
shake of wheel
will
be just perceptible and the 337

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

u
MISCEIiLaNEOUS

Contents

SUBJECT
PAR.

Abbreviations
U-15
Extra
Equipment U-2

Front
Bumper Weight U-9
Governor
U-3

Governor
Adjustment U-4

Governor
Maintenance. U-6

U-1. GENERAL

Miscellaneous information included in this sectioi
includes coverage of extra equipment, special
tools,
torque specifications, and charts and tables.

U-2. EXTRA
EQUIPMENT

Much
of the utility of the
*
Jeep*
Universal
is due to
the extra equipment which has been designed to adapt it for farming and industry. The mainte­
nance and use of
some
of this equipment is out­
lined
in this section.

U-3.
Governor Assembly

The
Novi governor is supplied for models equipped

with
the F4 engine.
This
is a centrifugal type governor and is illustrated in Fig. U-2. Complete

installation
instructions are supplied with each
assembly. Adjustment and operating procedures

are
given below.

U-4.
Governor Adjustment

a.
Adjust the carburetor to obtain smooth
engine

idle at 600 rpm., then
stop
the engine.
b.
Check
throttle linkage to ensure maximum
throttle opening. Be certain that throttle and
governor linkage is free.

c.
Place the carburetor throttle in wide-open posi­ tion and
pull
the governor control handle out to
the last notch. Adjust the governor to bellcrank

rod
so that the linkage
will
hold the carburetor
throttle in wide-open position.

d.
Close the governor control and start the
engine

Again
pull
the control out to the last notch and

adjust
the length of the cable at adjusting yoke so
that the
engine
will
run at
2600
rpm. Close the

control
to recheck the linkage for free action and
to make sure the
engine
will
return to 600 rpm.
idle speed.

If
the
engine
runs faster than this speed,
loosen

the lock nut which locks the governor hand control
handle on the dash to the rod and back off the
handle until the carburetor idle speed adjusting

screw
bears on the stop. Tighten the lock nut.
In
the absence of electrical tachometer equipment,

engine
speed may be determined by the speedom­
eter. Safely
jack
up the
rear
wheels and be sure the front wheel drive is not
engaged.
When driving
the
rear
wheels in high or direct transmission gear,
the
speedometer
will
read from 13j^ to 15 mph. [21.6 to 24.0 kph.] at an
engine
speed of from 900
to 1000 rpm.
SUBJECT
PAR.

Heater
U-10 Miscellaneous Data U-16

Pintle
Hook 1X7
Special
Tools. U-ll
Torque
Specifications U-13, 14, 15

Standard
and Recommended Tools
j.
.U-12

U-5.
Novi Governor Operation /

The
Novi governor is directly belted to the F4

engine
as no clutch is provided to disconnect the
drive.

To
operate the vehicle
WITHOUT
governor con­
trol,
push the governor hand control all the way
IN
against the instrument panel.

To
operate the vehicle
WITH
governor control,

pull
the governor hand control handle out. The
hand
control has nine notched positions. Pulling the

control
out to the first notch
sets
the controlled

engine
speed at approximately 1000 rpm. and each successive notch increases the speed 200 rpm.

until
2600
rpm. is reached in the ninth notch. The

hand
control may be released by turning the han­ dle one-quarter
turn
in either direction.

When
the
engine
is being operated under governor

control
(hand control out) the controlled
engine

speed may be
exceeded
at any time by depressing
the
foot
accelerator in the conventional manner to
secure a greater carburetor throttle opening than
that determined by the governor hand control
setting.

U-6.
Governor Maintenance

The
belt tension may be adjusted by raising or
lowering the governor in the slotted
holes
in the mounting bracket. Keep the pulleys and belt free
of
dirt
and oil. Belt slippage
will
affect governor
operation and a tight belt may cause
rapid
wear
of the governor shaft and bearings. Adjust it to
allow Yi' [12,7 mm.] depression midway
between
the pulleys with thumb pressure.
There
is little wear of the internal parts for they
operate in oil. The governor housings are equipped

with
both
fill
and
drain
plugs and also with level

indicating
plugs.
Check
the oil level at each vehicle
lubrication
and change the oil each time the en­

gine
oil is changed using the same grade oil used

in
the engine.

Caution:
Do not
fill
the governor housing above
the level plug. Overfilling
will
prevent governor
control
and possibly cause damage to governor in­

ternal
parts. The capacity of
these
governors is two fluid ounces [59,15 cm3]. The filler plug is
also a vent which should be cleaned thoroughly at
each oil change to be sure that the vent operates.

U-7.
Pintle Hook

The
standard type pintle hook, Fig. U-1, affords a
safe, easy hitch for towing a
trailer
or other vehicle. 357

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

U
DESCRIPTION
—
Continued

AXLES

W-99* Gauge — Pinion & Ring
Gear
Setting
W-104-B* Puller — Tapered Roller Bearing Removing
W-126* Driver — Pinion Bearing Cup
W-128* Installer — Differential Inner Oil Seal W-129 Spreader — Differential
Carrier
Housing
W-138* Driver & Adapter —
King
Pin Bearing
W-144* Wrench — Wheel Bearing Adjusting Nut W-147* Driver — Pinion Oil Seal W-163* Puller
—-
Axle Shaft Drive Flange
W-186* Driver — Axle Shaft Oil Seal
W-188* Driver — Differential Case Bearing W-251* Puller — Pinion Oil Seal
W-262*
Sleeve
— Pinion Bearing Installing

W-263
Semi-Floating
Rear
Axle Shaft Oil Seal W-264* Driver — Pinion Outer Bearing Cup
W-297* Torque Wrench — Pinion Bearing Adjusting W-343* Remover
85
Installer —
Rear
Axle Bearing (Flanged Axle)
W-344* Installer — Pinion Inner Bearing Cups

C-319-A
Puller —
Rear
Wheel Hub (Tapered Axle Shaft)
C-690 Checking Scale —
King
Pin Bearing Preload DD-914-P Press — Tapered Roller Bearing Removing
DD-914-9 Reducer Ring — Differential & Pinion Bearings (Use with DD-914-P)

C-3
716 Driver — Differential
Carrier
Bearing C-4142
Gear
Rotating Tool —
Trac-Lok
Differential
**Jeep*
exclusive
tool

Steering
Group

C-3646 Puller, Steering Shaft Arm

Brake
Group

W-172 Puller, Parking Brake Drum
U-12.
STflNDfiRD
AND
RECOMMENDED
TOOLS

Tool
Description
ENGINE

W-292
Tester — Cooling
System
Thermostat
C-119 Indicator — Cylinder Bore C-385 Compressor — Piston Ring
C-647 Fixture — Spring Testing
C-823
Hone
— Cylinder Bore Refinishing
C-3012 Reamer — Cylinder Ridge
C-3250 Pliers — Radiator fis Heater
Hose
Wire Clamp
C-3411
Gauge — Pressure & Vacuum
C-3422-A Compressor — E-type Valve Spring
C-3501
Hone
— Cylinder
Deglazing
C-3514
Flusher — Cooling
System

C-3886 Fixture — Carburetor Holding C-3896-A Tachometer — Portable
C-3943 Gauge — Compression Checking
C-3952 Torque Wrench, 150
lb-ft.
Swivel Head C-3953 Stand, Engine Repair
C-3959 Light — Ignition Timing
C-4065 Wrench — Oil Filter Removing
C-4080 Tester — Cooling
System
fig
Pressure Cap

ELECTRICAL

40B Hydrometer — Battery Service
W-291 Tester — Instrument
C-3674
Aimers —
Headlight
(Pair)
C-3829 Tester —
Diode
Polarity
C-3888 Tester — Volt-Ampere C-3950 Tester — 12V 60 Amp. Carbon Pile Resistor 361

u
MISCELLANEOUS
U-12.
STANDARD
AND
RECOMMENDED TOOLS
(Continued)

Tool
Description
CLUTCH

W-296 Fixture — Adjusting

TRANSMISSION

C-3201
- A
Lo-Jack
— Floor Type

AXLE

C-637 Puller — Axle Shaft & Oil Seal

STEERING

DD-428 Gauge — Camber & Caster
DD-435 Turntables — Wheel Alignment C-3479 Gauge & Scribe — Toe-in Checking

BRAKES

C-416 Clamps — Brake Cylinder Retaining C-3080 Hone — Brake Cylinder
C-3496-B Bleeder — Hydraulic Pressure Type C-3785 Remover & Installer — Brake Return Spring
C-3920 Micrometer — Brake Drum Checking
U-13.
ENGINE TORQUE SPECIFICATIONS HURRICANE
F4
ENGINE

Pounds - Feet
kg-m.

30-40
4,1
a

5,5

Camshaft
Thrust Plate Bolt
20-26

2,8
a
3,6

Clutch
Control
Ball
Stud — [7,93 mm.]
35-45

4,8
a
6,2
Connecting Rod Cap Bolt Nut — y8" [9,53 mm.|
35-45

4,8
a
6,2

60-70
8,3
a
9,7

Cylinder
Head to Block Bolts
60-70
8,3
a
9,7

45-55
6,2
a
7,6

29-35
4,0
a
4,8

Flywheel
to Crankshaft Bolt. 35-41
4,8
a

5,7

Fuel
Pump Mounting Bolts 13-17 1,8
a
2,4
Alternator Bracket to Cylinder Block.
25-35
3,5
a
4,8

29-35
4,0

a
4,8

Main
Bearing
Caps.
.
65-75
9,0
a
10,4

Oil
Pan
Drain
Plug
25-35

3,5
a

4,8
9-14 1,2
a

1,9
Piston Pin
Lock
Bolt 35-41
4,8
a

5,7

30-36
4,1
a

5,0

Spark
Plugs to Cylinder Head
25-33

3,5
a
4,6
Starting Motor Mounting Bolt.
20-25
2,8
a
3,5
7-10 0,9
a
1,4

Water
Outlet Elbow to Cylinder Head
20-25
2,8

a
3,5

Water
Pump to Cylinder Block 12-17
1,7
a

2,4

NOTE:
Turn
the connecting rod cap nut locks (inverted type, pressed
steel)
finger
tight
and then
tighten
% turn more with wrench
362