ECU JEEP GLADIATOR 2023 Owner's Guide

94GETTING TO KNOW YOUR VEHICLE
5. Using the provided #T50 Torx head driver and ratchet, install and tighten the Torx fasteners
by turning them clockwise. Secure them until
they are snug, being careful not to cross-
thread the fasteners or overtighten. Refer to
the following table for recommended torque
specifications. Repeat on the opposite side.

Step Five Step Five
6. Before driving the vehicle with the top in the
Sunrider® position, ensure the top is secured
with the provided hook-and-loop fasteners
Úpage 89.

Step Six

Torque
Specification For Torx
Fasteners Maximum Minimum
119.5 in-lb (13.5 N·m) 150.5 in-lb
(17.0 N·m) 106.2 in-lb
(12.0 N·m)
CAUTION!
Do not overtighten Torx fasteners. You can strip
the fasteners if they are overtightened.

23_JT_OM_EN_USC_t.book Page 94

98GETTING TO KNOW YOUR VEHICLE
4. Unfold the outer flap and zip the hard top bag closed.

Step Four

5. Store the Freedom Top panels bag in a safe location.
HARD TOP FRONT PANEL(S)
I
NSTALLATION

1. Set the right side panel on the windshield
frame with the locating pin in the front
receiver mounting hole, followed by the left
side panel, making sure there is no overhang.
Make sure that the panels are sitting flush
with the body.
2. Secure the panel(s) using the same steps for
removal in reverse order.
NOTE:To prevent water leaks, the seals and hard top
panels should be clear of any dust and debris prior
to reinstallation.
REMOVING THE HARD TOP
Use this QR code to access your
digital experience.

1. Remove both front panels

Ú
page 95.

2. Open both front doors.
3. Using the provided #50 Torx head driver and ratchet, remove the two Torx
head screws that secure the hard top at the
B-pillar (near the top of the front doors).
Step Three

4. If equipped, remove the lower interior soft trim panel (attached by the hook-and-loop
fastener) by pulling the panel away from the
trim.

Step Four

23_JT_OM_EN_USC_t.book Page 98

GETTING TO KNOW YOUR VEHICLE99
5. Remove the Torx head fasteners that secure the hard top to the vehicle: two along the
interior body side, rearward of the back doors,
followed by the four fasteners along the back
of the vehicle cab using the #T50 Torx head
driver.

Step Five
6. Locate the wire harness on the left rear inside
corner of the vehicle. To access the harness,
remove the plastic cover by pushing the cover
to the side, and sliding it off.
NOTE:Do not force open; this will break the plastic cover.

Step Six

7. To release the wire harness, pull back on the red latch (1), then push down on the black
button (2) while pulling the harness out.
Step Seven

8. Remove the hard top from the vehicle. Install the provided edge protectors along the bottom
edges of the hard top, and place the hard top
on a soft surface to prevent damage.
1 — Vehicle Cab Torx Head Fasteners
2 — Body side Torx Head Fasteners
1 — Red Latch
2 — Black Button
CAUTION!
The removal of the Hard Top requires four adults
located on each corner. Failure to follow this
caution could damage the Hard Top.
2

23_JT_OM_EN_USC_t.book Page 99

100GETTING TO KNOW YOUR VEHICLE
9. Store the wire harness by removing the storage cover on the quarter trim. Use the
mechanical key blade to pry the cover open.

Step Nine

10. Tuck the wire harness inside the storage compartment, and replace the cover.

Step Ten

INSTALLING THE HARD TOP
If the door frames are installed from soft top
usage, they must be removed prior to installation
of the hard top Ú page 104. To install the hard top, place the hard top on the
vehicle while making sure that the top is sitting
flush with the body at the sides and across the
back. Then follow the removal steps in reverse
order.
NOTE:
Inspect the hard top seals for damage and
replace if necessary.
Install the hard top using the same steps for
removal in reverse order.
When reinstalling the interior soft trim panel:
Be sure the panel is centered so that there
is an even gap on both sides.
Apply pressure over the hook-and-loop
fasteners to ensure they are properly
secured.

The Torx head fasteners that attach the hard top to
the body should be torqued to 155 in-lb +/- 22 in-lb
(17.5 N·m +/- 2.5 N·m) using the provided #T50 Torx
head driver and ratchet.

CAUTION!
The front panel(s) must be positioned properly
to ensure sealing. Improper installation can
cause water to leak into the vehicle's interior.
The hard top assembly must be positioned
properly to ensure sealing. Improper installa -
tion can cause water to leak into the vehicle's
interior.
The hard top is not designed to carry any addi -
tional loads, such as after-market roof racks,
spare tires, building materials, hunting or
camping supplies, etc. Ú page 115.
Do not move your vehicle until the top has
been either fully attached to the windshield
frame and body, or fully removed.
The removal of the hard top requires four
adults located on each corner. Failure to
follow this caution could damage the hard top.
CAUTION!
Do not overtighten Torx fasteners. Damage to
the retainers will occur.

23_JT_OM_EN_USC_t.book Page 100

GETTING TO KNOW YOUR VEHICLE103
To Open The Sunrider® Top
To open the Sunrider® top, proceed as follows:

1. Fold both sun visors forward against the windshield.

2. Release the header latches from the crossbar by pulling the handle downward. Make sure
the hook is disengaged from its receiver.

Release Both Header Latches
3. From the front of the Sunrider® top, lift and
push the top rearward to the Sunrider®
position.

Sunrider® Position
4. Secure the top by using the two hook-and-loop
fasteners provided with the Sunrider® kit, and
wrap one around the side rails on each side of
the Sunrider® top to hold it in place.

Hook-And-Loop Fastener Placement

2

23_JT_OM_EN_USC_t.book Page 103

104GETTING TO KNOW YOUR VEHICLE
DOOR FRAME — IF EQUIPPED WITH A SOFT
TOP DOOR FRAME REMOVAL
NOTE:The rear door frames must be removed first,
followed by the front door frames.

1. Using the provided #T40 Torx head driver and
ratchet, loosen the Torx head fasteners
located on the underside of each door hinge
(two per door), and remove the fasteners by
pulling downward.

Step One

NOTE:The fasteners will not fall out once completely
loose, as they are held in place by design.
Step One

2. Lift the frame upward, removing it from the vehicle.

Step Two

3. Store the fasteners in a secure location.
4. Repeat the procedure on the front door frame.
WARNING!
Do not drive your vehicle on public roads with
the door frame(s) removed as you will lose the
protection that they can provide. This procedure
is furnished for use during off-road operation
only.
CAUTION!
Failure to follow these cautions may cause
interior water damage, stains or mildew:
Opening a door or lowering a window while the
top is wet may allow water to drip into the
vehicle's interior.
Careless handling and storage of the remov -
able door frame(s) may damage the seals,
causing water to leak into the vehicle's inte -
rior.
The door frame(s) must be positioned properly
to ensure sealing. Improper installation can
cause water to leak into the vehicle's interior.

23_JT_OM_EN_USC_t.book Page 104

106GETTING TO KNOW YOUR VEHICLE
(Continued)
6. Insert the fasteners from underneath. Tighten
with the #T40 Torx head driver until they are
snug, being careful not to cross-thread the
fasteners or overtighten. Refer to the previous
table for the appropriate torque specifications
for the door frame fasteners.
FOLDING WINDSHIELD
The fold-down windshield on your vehicle is a
structural element that can provide protection in
some accidents. The windshield also provides
protection against weather, road debris and
intrusion of small branches and other objects.
Do not drive your vehicle on-road with the
windshield down, as you lose the protection this
structural element provides.
If required for certain off-road uses, the windshield
can be folded down. However, the protection
afforded by the windshield is then lost. If you fold
down the windshield, drive slowly and cautiously. It
is recommended that the speed of the vehicle be
limited to 10 mph (16 km/h), with low range
operation preferred if you are driving off-road with
the windshield folded down. Raise the windshield as soon as the task that
required its removal is completed and before you
return to on-road driving. Both you and your
passengers should wear seat belts at all times,
on-road and off-road, regardless of whether the
windshield is raised or folded down.
LOWERING THE WINDSHIELD

1. Before completing the following steps:

If your vehicle is equipped with a soft top,
the top
MUST be lowered Ú page 83, and
the door frames must be removed
Ú page 104 prior to lowering the wind -
shield.
If your vehicle is equipped with a hard top,
the Freedom Panels MUST be removed
prior to lowering the windshield Úpage 95.
WARNING!
Carefully follow these warnings to help protect
against personal injury:
Do not drive your vehicle on-road with the
windshield down.
Do not drive your vehicle unless the wind -
shield is securely fastened, either up or down.
Eye protection, such as goggles, should be
worn at all times when the windshield is down.
Be sure that you carefully follow the instruc -
tions for raising the windshield. Make sure
that the folding windshield, windshield wipers,
side bars, and all associated hardware and
fasteners are correctly and tightly assembled
before driving your vehicle. Failure to follow
these instructions may prevent your vehicle
from providing you and your passengers’
protection in some accidents.
If you remove the doors, store them outside
the vehicle. In the event of an accident, a
loose door may cause personal injury.
CAUTION!
Failure to follow this step will cause damage to
the vehicle’s header seal.
WARNING!

23_JT_OM_EN_USC_t.book Page 106

GETTING TO KNOW YOUR VEHICLE107
2. Manually remove the protective caps over the windshield wiper hex bolts.

Step Two

3. Using the provided 15 mm socket, remove the two hex bolts and remove the wiper arms.
4. Move to the inside of the vehicle and lower both sun visors. 5. Using the provided #T40 Torx head driver,
remove the four Torx head fasteners located
along the interior of the windshield (two on
each side of the header trim).

Step Five

NOTE:Store all of the mounting bolts in their original
threaded holes and tighten for safekeeping, or in
the fastener bin located below the rear seat. 6. Lower the windshield gently until it contacts
the tie-down bumpers (if equipped).

Step Six

7. Secure the windshield by passing a cinch strap through the tie-down bumper on either side of
the hood and on the windshield frame. Tighten
the strap to secure the windshield in place.
1 — Hex Bolt Cover Installed
2 — Hex Bolt Cover Removed
1 — Outer Torx Fasteners
2 — Center Torx Fasteners
1 — Washer Nozzle
2 — Bumper
3 — Tie-Down
CAUTION!
Do Not Overtighten! Damage to the windshield
could result.
2

23_JT_OM_EN_USC_t.book Page 107

108GETTING TO KNOW YOUR VEHICLE
Adaptive Cruise Control (ACC)/Forward
Collision Warning (FCW) Sensor Protective
Cover — If Equipped
Your vehicle may be equipped with a protective
cover that is to be used whenever the windshield is
folded down in order to protect the ACC/FCW
sensor. To install the cover, refer to the following
instructions:

1. Secure the top part of the cover so that it
hinges to the header.

2. Swing the cover down and push on it so that it covers the opening.
3. Check to make sure the cover is secured properly.

Protective Cover Installed

NOTE:Be sure to remove the cover before returning the
windshield to the normal position. Store the cover
in the cargo area.
Cleaning Instructions
During windshield down applications, dust/dirt can
accumulate in the cover and block the camera
lens. Use a microfiber cloth to clean the camera
lens, module, and inside cover, being careful not to
damage or scratch the module.
RAISING THE WINDSHIELD

1. Release the strap that secured the windshield in the lowered position.

2. Raise the windshield.
3. Using the provided #T40 Torx head driver, reinstall the four Torx head fasteners located
along the interior of the windshield (two on
each side of the header trim). Secure them
until they are snug, being careful not to
cross-thread the fasteners or overtighten.
Step Three

4. Reinstall the windshield wiper arms using the provided 15 mm socket. First, align the tips of
the blade to the “T” mark in the glass. Then,
while holding the arm in that position, reinstall
the hex nut and tighten until snug. Be careful
not to overtighten. Repeat for the other arm.1 — Outer Torx Fasteners
2 — Center Torx Fasteners

23_JT_OM_EN_USC_t.book Page 108

GETTING TO KNOW YOUR VEHICLE109
5. Reinstall the protective caps over the wiper arm hex bolts and push gently until they snap
into place.

Step Five

NOTE:Make sure the windshield is raised prior to
installing the tops.
HOOD
OPENING THE HOOD
Release both of the outside hood latches.
Hood Latch Locations

Raise the hood slightly, and place a hand
palm-side down in the center of the hood opening.
Locate the safety latch in the middle, and push the
latch to the right to open.

Place Hand In Hood Opening
Remove the support rod from the hood, and insert
it into the radiator crossmember.
NOTE:
Vehicle must be at a stop and the gear selector
must be in PARK.
You may have to push down slightly on the hood
before pushing the safety latch.
While lifting the hood, use both hands.
Before lifting the hood, check that the wiper
arms are not in motion and not in the lifted posi
-
tion.
CLOSING THE HOOD
To close the hood, remove the support rod from the
radiator crossmember, and install into the clip on
the hood. Lower the hood slowly. Secure both of
the hood latches.
1 — Hex Bolt Cover Installed
2 — Hex Bolt Cover Removed
WARNING!
Be sure the hood is fully latched before driving
your vehicle. If the hood is not fully latched, it
could open when the vehicle is in motion and
block your vision. Failure to follow this warning
could result in serious injury or death.
2

23_JT_OM_EN_USC_t.book Page 109