audio JEEP GRAND CHEROKEE 2012 Owner handbook (in English)

Denmark, Finland, France, Germany, Greece,
Hungary, Ireland, Italy, Luxembourg, Nether-
lands, Norway, Poland, Portugal, Romania,
Russian Federation, Slovenia, Spain, Sweden,
Switzerland, Yugoslavia, and United Kingdom.
Operation is subject to the following conditions:
•This device may not cause harmful interfer-
ence.
• This device must accept any interference
that may be received, including interference
that may cause undesired operation.
VEHICLE SECURITY ALARM — IF
EQUIPPED
The Vehicle Security Alarm monitors the hood,
liftgate, liftgate flipper glass, vehicle doors for
unauthorized entry, and the ignition switch for
unauthorized operation.
If something triggers the alarm, the Vehicle
Security Alarm will provide the following audio
and visual signals: the horn will pulse, the
headlights will turn on, the park lights will flash,
and the Vehicle Security Light in the instrument
cluster will flash.
To Arm The SystemFollow these steps to arm the Vehicle Security
Alarm:
1. Remove the key from the ignition system
(refer to Starting Procedures inStarting And
Operating for further information).
• For vehicles equipped with Keyless Enter-N-
Go, make sure the vehicle ignition system is
OFF.
• For vehicles not equipped with Keyless Enter-
N-Go, make sure the vehicle ignition system is
OFF and the key is physically removed from
the ignition.
2. Perform one of the following methods to lock
the vehicle:
• Press LOCK on the interior power door lock
switch with the driver and/or passenger door
open.
• Press the LOCK button on the exterior Pas-
sive Entry Door Handle with a valid Key Fob
available in the same exterior zone (refer to
Keyless Enter-N-Go inThings To Know Be-
fore Starting Your Vehicle for further informa-
tion). •
Press the LOCK button on the Remote Key-
less Entry (RKE) transmitter.
3. If any doors are open, close them.
To Disarm The SystemThe Vehicle Security Alarm can be disarmed
using any of the following methods:
• Press the UNLOCK button on the Remote
Keyless Entry (RKE) transmitter.
• Grasp the Passive Entry Unlock Door Handle
(if equipped, refer to Keyless Enter-N-Go in
Things To Know Before Starting Your Ve-
hicle for further information).
• Cycle the vehicle ignition system out of the
OFF position.
• For vehicles equipped with Keyless Enter-
N-Go, press the Keyless Enter-N-Go
Start/Stop button (requires at least one
valid Key Fob in the vehicle).
• For vehicles not equipped with Keyless
Enter-N-Go, insert a valid key into the
ignition switch and turn the key to the ON
position.
16

Enhanced Seat Belt Use Reminder
System (BeltAlert)
BeltAlertis a feature intended to remind the
driver and front passenger (if equipped with
front passenger BeltAlert) to fasten their seat
belts. The feature is active whenever the igni-
tion is on. If the driver or front seat passenger is
unbelted, the Seat Belt Reminder Light will turn
on and remain on until both front seat belts are
fastened.
The BeltAlert warning sequence begins after
the vehicle speed is over 5 mph (8 km/h), by
blinking the Seat Belt Reminder Light and
sounding an intermittent chime. Once the se-
quence starts, it will continue for the entire
duration or until the respective seatbelts are
fastened. After the sequence completes, the
Seat Belt Reminder Light remains illuminated
until the respective seat belts are fastened. The
driver should instruct all other occupants to
fasten their seat belts. If a front seat belt is
unbuckled while traveling at speeds greater
than 5 mph (8 km/h), BeltAlert will provide
both audio and visual notification. The front passenger seat BeltAlert
is not ac-
tive when the front passenger seat is unoccu-
pied. BeltAlert may be triggered when an
animal or heavy object is on the front passen-
ger seat or when the seat is folded flat (if
equipped). It is recommended that pets be
restrained in the rear seat in pet harnesses or
pet carriers that are secured by seat belts, and
cargo is properly stowed.
BeltAlert can be enabled or disabled by your
authorized dealer. Chrysler Group LLC does
not recommend deactivating BeltAlert .
NOTE:
Although BeltAlert has been deactivated,
the Seat Belt Reminder Light will continue to
illuminate while the driver’s or front passen-
ger (if equipped with belt alert) seat belt
remains unfastened.
Seat Belt Lock OutThe center rear seat belt system has a lock out
feature that will not allow you to extract the
center webbing unless the rear seat upper
latch is engaged.
Seat Belts And Pregnant WomenWe recommend that pregnant women use the
seat belts throughout their pregnancy. Keeping
the mother safe is the best way to keep the
baby safe.
Pregnant women should wear the lap part of
the belt across the thighs and as snug across
the hips as possible. Keep the belt low so that
it does not come across the abdomen. That
way the strong bones of the hips will take the
force if there is an accident.
Supplemental Restraint System
(SRS) — Air Bags
This vehicle has Advanced Front Air Bags for
both the driver and front passenger as a
supplement to the seat belt restraint systems.
The driver’s Advanced Front Air Bag is
mounted in the center of the steering wheel.
The passenger’s Advanced Front Air Bag is
mounted in the instrument panel, above the
37

When RCP is on and the vehicle is in REVERSE,
the driver is alerted using both the visual and
audible alarms, including reducing the radio
volume.
WARNING!
RCP is not a Back Up Aid system. It is
intended to be used to help a driver detect an
oncoming vehicle in a parking lot situation.
Drivers must be careful when backing up,
even when using RCP. Always check carefully
behind your vehicle, look behind you, and be
sure to check for pedestrians, animals, other
vehicles, obstructions, and blind spots before
backing up. Failure to do so can result in
serious injury or death.
Modes Of OperationThree selectable modes of operation are avail-
able in the Electronic Vehicle Information Center
(EVIC). Refer to “Electronic Vehicle Information
Center (EVIC)/Personal Settings (Customer-
Programmable Features)” in “Understanding
Your Instrument Panel” for further information.
Blind Spot Alert
When operating in Blind Spot Alert mode, the
BSM system will provide a visual alert in the
appropriate side view mirror based on a de-
tected object. However, when the system is
operating in RCP, the system will respond with
both visual and audible alerts when a detected
object is present. Whenever an audible alert is
requested, the radio volume is reduced.
Blind Spot Alert Lights/Chime
When operating in Blind Spot Alert Lights/
Chime, the BSM system will provide a visual
alert in the appropriate side view mirror based
on a detected object. If the turn signal is then
activated, and it corresponds to an alert pres-
ent on that side of the vehicle, an audible chime
will also be sounded. Whenever a turn signal
and detected object are present on the same
side at the same time, both the visual and audio
alerts will be issued. In addition to the audible
alert the radio (if on) volume will be reduced.
NOTE:
•Whenever an audible alert is requested by
the BSM system, the radio volume is re-
duced. •
If the hazard flashers are on, the system
will request the appropriate visual alert
only.
When the system is in RCP, the system shall
respond with both visual and audible alerts
when a detected object is present. When-
ever an audible alert is requested, the radio
volume is reduced. Turn/hazard signal status
is ignored; the RCP state always requests
the chime.
Blind Spot Alert Off
When the BSM system is turned off there will be
no visual or audible alerts from either the BSM
or RCP systems.
NOTE:
The BSM system will store the current oper-
ating mode when the vehicle is shut off.
Each time the vehicle is started the previ-
ously stored mode will be recalled and used.
Astronomy Zone — System Temporarily
Unavailable
When the vehicle enters this zone the blind
spot system will become temporarily unavail-
able and the EVIC will display the message “
Blind spot system unavailable-Astronomy 73

zone”. The side mirrors LED’s will be lit up and
stay lit until the vehicle exits the zone.
Uconnect™ Phone — IF EQUIPPED
NOTE:
For Uconnect™ Phone with Navigation or
Multimedia radio, refer to the Navigation or
Multimedia radio’s User’s Manual (separate
booklet) Uconnect™ Phone section.
Uconnect™ Phone is a voice-activated, hands-
free, in-vehicle communications system.
Uconnect™ Phone allows you to dial a phone
number with your mobile phone* using simple
voice commands (e.g., “Call”“Jim”“Work” or
“Dial”“151-1234 -5555”). Your mobile phone’s
audio is transmitted through your vehicle’s au-
dio system; the system will automatically mute
your radio when using the Uconnect™ Phone.
Uconnect™ Phone allows you to transfer calls
between the Uconnect™ Phone and your mo-
bile phone as you enter or exit your vehicle and
enables you to mute the Uconnect™ Phone’s
microphone for private conversation. The Uconnect™ Phone is driven through your
Bluetooth
“Hands-Free profile” mobile phone.
Uconnect™ Phone features Bluetooth tech-
nology - the global standard that enables dif-
ferent electronic devices to connect to each
other without wires or a docking station, so
Uconnect™ Phone works no matter where you
stow your mobile phone (be it your purse,
pocket, or briefcase), as long as your phone is
turned on and has been paired to the vehicle’s
Uconnect™ Phone. The Uconnect™ Phone al-
lows up to seven mobile phones to be linked to
the system. Only one linked (or paired) mobile
phone can be used with the Uconnect™ Phone
at a time. The Uconnect™ Phone is available in
English, Dutch, French, German, Italian or
Spanish languages (as equipped).
WARNING!
Any voice commanded system should be
used only in safe driving conditions following
local laws and phone use. All attention should
be kept on the roadway ahead. Failure to do
so may result in a collision causing serious
injury or death. Uconnect™ Phone Button
The radio or steering wheel con-
trols (if equipped) will contain the
two control buttons (Uconnect™
Phone
button and Voice Com-
mandbutton) that will en-
able you to access the system.
When you press the button you will hear the
word Uconnect™ followed by a BEEP. The
beep is your signal to give a command.
Voice Command Button Actual button location may vary
with radio. The individual buttons
are described in the “Operation”
section.
The Uconnect™ Phone can be used with
Hands-Free Profile certified Bluetooth mobile
phones. Some phones may not support all the
Uconnect™ Phone features. Refer to your mo-
bile service provider or the phone manufacturer
for details.
The Uconnect™ Phone is fully integrated with
the vehicle’s audio system. The volume of the
Uconnect™ Phone can be adjusted either from
74

•Note that only the phonebook in the current
language is deleted.
• Automatic downloaded phonebook entries
cannot be deleted or edited.
List All Uconnect™ Phonebook Names
• Press the
button to begin.
• After the “Ready” prompt and the following
beep, say “Phonebook List Names”.
• The Uconnect™ Phone will play the names
of all the phonebook entries, including the
downloaded phonebook entries, if available.
• To call one of the names in the list, press the
button during the playing of the de-
sired name, and say “Call”.
NOTE:
The user can also exercise “Edit” or “De-
lete” operations at this point.
• The Uconnect™ Phone will then prompt you
as to the number designation you wish to
call.
• The selected number will be dialed.
Phone Call FeaturesThe following features can be accessed
through the Uconnect™ Phone if the feature(s)
are available on your mobile service plan. For
example, if your mobile service plan provides
three-way calling, this feature can be accessed
through the Uconnect™ Phone. Check with
your mobile service provider for the features
that you have.
Answer Or Reject An Incoming Call — No
Call Currently In Progress
When you receive a call on your mobile phone,
the Uconnect™ Phone will interrupt the vehicle
audio system, if on, and will ask if you would
like to answer the call. Press the
button to
accept the call. To reject the call, press and
hold the
button until you hear a single
beep indicating that the incoming call was
rejected.
Answer Or Reject An Incoming Call — Call
Currently In Progress
If a call is currently in progress and you have
another incoming call, you will hear the same
network tones for call waiting that you normally
hear when using your mobile phone. Press the
button to place the current call on hold and
answer the incoming call.
NOTE:
The Uconnect™ Phone compatible phones
in the market today do not support rejecting
an incoming call when another call is in
progress. Therefore, the user can only an-
swer an incoming call or ignore it.
Making A Second Call While Current Call In
Progress
To make a second call while you are currently
on a call, press the
button and say “Dial”
or “Call” followed by the phone number or
phonebook entry you wish to call. The first call
will be on hold while the second call is in
progress. To go back to the first call, refer to
“Toggling Between Calls”. To combine two
calls, refer to “Conference Call”.
Place/Retrieve A Call From Hold
To put a call on hold, press the
button until
you hear a single beep. This indicates that the
call is on hold. To bring the call back from hold,
press and hold the
button until you hear a
single beep.
79

bile phone, the audio will be played through
your vehicle’s audio system. The Uconnect™
Phone will work the same as if you dialed the
number using a Voice Command.
NOTE:
Certain brands of mobile phones do not
send the dial ring to the Uconnect™ Phone
to play it on the vehicle audio system, so
you will not hear it. Under this situation,
after successfully dialing a number the user
may feel that the call did not go through
even though the call is in progress. Once
your call is answered, you will hear the
audio.
Mute/Un-Mute (Mute Off)
When you mute the Uconnect™ Phone, you will
still be able to hear the conversation coming
from the other party, but the other party will not
be able to hear you. In order to mute the
Uconnect™ Phone:
•Press the
button.
• Following the beep, say “Mute”. In order to un-mute the Uconnect™ Phone:
•
Press the
button.
• Following the beep, say “Mute off”.
Advanced Phone Connectivity
Transfer Call To And From Mobile Phone
The Uconnect™ Phone allows ongoing calls to
be transferred from your mobile phone to the
Uconnect™ Phone without terminating the call.
To transfer an ongoing call from your
Uconnect™ Phone paired mobile phone to the
Uconnect™ Phone or vice versa, press the
button and say “Transfer Call”.
Connect Or Disconnect Link Between The
Uconnect™ Phone And Mobile Phone
Your mobile phone can be paired with many
different electronic devices, but can only be
actively connected with one electronic device
at a time.
If you would like to connect or disconnect the
Bluetooth connection, your mobile phone, and
the Uconnect™ phone system, follow the in-
structions described in your mobile phone Us-
er’s Manual. List Paired Mobile Phone Names
•
Press the
button to begin.
• After the “Ready” prompt and the following
beep, say “Setup Phone Pairing”.
• When prompted, say “List Phones”.
• The Uconnect™ Phone will play the phone
names of all paired mobile phones in order
from the highest to the lowest priority. To
“select” or “delete” a paired phone being
announced, press the
button and say
“Select” or “Delete”. Also, see the next two
sections for an alternate way to “select” or
“delete” a paired phone.
Select Another Mobile Phone
This feature allows you to select and start using
another phone paired with the Uconnect™ Phone.
• Press thebutton to begin.
• After the “Ready” prompt and the following
beep, say “Setup Select Phone” and follow
the prompts.
• You can also press the
button at any
time while the list is being played, and then
choose the phone that you wish to select.
83

•low road noise,
• smooth road surface,
• fully closed windows,
• dry weather conditions.
• Even though the system is designed for
users speaking in European English, Dutch,
French, German, Italian, or Spanish accents,
the system may not always work for some.
• When navigating through an automated sys-
tem such as voice mail, or when sending a
page, at the end of speaking the digit string,
make sure to say “Send”.
• Storing names in the phonebook when the
vehicle is not in motion is recommended.
• It is not recommended to store similar sound-
ing names in the Uconnect™ Phonebook.
• Phonebook (Downloaded and Uconnect™
Phone Local) recognition rate is optimized
when the entries are not similar.
• Numbers must be spoken in single digits.
“800” must be spoken “eight-zero-zero” not
“eight hundred”. •
You can say “O” (letter “O”) for “0” (zero).
• Even though international dialing for most
number combinations is supported, some
shortcut dialing number combinations may
not be supported.
• In a convertible vehicle, system perfor-
mance may be compromised with the con-
vertible top down.
Far End Audio Performance
• Audio quality is maximized under:
• low-to-medium blower setting,
• low-to-medium vehicle speed,
• low road noise,
• smooth road surface,
• fully closed windows,
• dry weather conditions, and
• operation from the driver seat.
• Performance, such as audio clarity, echo,
and loudness to a large degree rely on the
phone and network, and not the Uconnect™
Phone. •
Echo at the phone far end can sometimes be
reduced by lowering the in-vehicle audio
volume.
• In a convertible vehicle, system perfor-
mance may be compromised with the con-
vertible top down.
Recent Calls
If your phone supports “Automatic Phonebook
Download”, Uconnect™ Phone can list your
Outgoing, Incoming and Missed Calls.
SMS
Uconnect™ Phone can read or send new mes-
sages on your phone.
Read Messages:
If you receive a new text message while your
phone is connected to Uconnect™ Phone, an
announcement will be made to notify you that
you have a new text message. If you wish to
hear the new message:
• Press the
button.
• After the “Ready” prompt and the following
beep, say “SMS Read” or “Read Messages”.
85

Please note the volume setting for Voice Com-
mand is different than the audio system.
Main Menu
Start a dialogue by pressing the Voice Com-
mand
button. You may say “Main Menu”
to switch to the main menu.
In this mode, you can say the following com-
mands:
• “Radio” (to switch to the radio mode)
• “Disc” (to switch to the disc mode)
• “Memo” (to switch to the memo recorder)
• “Setup” (to switch to system setup)
Radio Am (Or Radio Long Wave Or Radio
Medium Wave — If Equipped)
To switch to the AM band, say “AM” or “Radio
AM”. In this mode, you may say the following
commands:
• “Frequency #” (to change the frequency)
• “Next Station” (to select the next station)
• “Previous Station” (to select the previous
station)
• “Menu Radio” (to switch to the radio menu) •
“Main Menu” (to switch to the main menu)
Radio FM
To switch to the FM band, say “FM” or “Radio
FM”. In this mode, you may say the following
commands:
• “Frequency #” (to change the frequency)
• “Next Station” (to select the next station)
• “Previous Station” (to select the previous
station)
• “Menu Radio” (to switch to the radio menu)
• “Main Menu” (to switch to the main menu)
Disc
To switch to the disc mode, say “Disc”. In this
mode, you may say the following commands:
• “Track” (#) (to change the track)
• “Next Track” (to play the next track)
• “Previous Track” (to play the previous track)
• “Main Menu” (to switch to the main menu) Memo
To switch to the voice recorder mode, say
“Memo”. In this mode, you may say the follow-
ing commands:
•
“New Memo” (to record a new memo) —
During the recording, you may press the
Voice Command
button to stop re-
cording. You proceed by saying one of the
following commands:
“Save” (to save the memo)
“Continue” (to continue recording)
“Delete” (to delete the recording)
• “Play Memos” (to play previously recorded
memos) — During the playback you may
press the Voice Command
button to
stop playing memos. You proceed by saying
one of the following commands:
“Repeat” (to repeat a memo)
“Next” (to play the next memo)
“Previous” (to play the previous memo)
“Delete” (to delete a memo)
• “Delete All” (to delete all memos)
92

WARNING ALERTS
Rear Distance (in/cm) Greater than 79 in (200 cm)79-39 in
(200-100 cm) 39-25 in
(100-65 cm) 25-12 in
(65-30 cm) Less Than 12 in
(30 cm)
Front Distance (in/cm) Greater than 47 in (120 cm)47-39 in
(120-100 cm) 39-25 in
(100-65 cm) 25-12 in
(65-30 cm) Less Than 12 in
(30 cm)
Audible Alert (Chime) NoneSingle 1/2
Second Tone Slow
FastContinuous
Display Message Park Assist System ONWarning Object
Detected Warning Object
Detected Warning Object
Detected Warning Object
Detected
Arcs None3 Solid
(Continuous) 3 Slow Flashing 2 Slow Flashing 1 Slow Flashing
Radio Volume Re- duced No
Yes YesYes Yes
NOTE:
ParkSense will reduce the volume of the
radio, if on, when the system is sounding an
audio tone.
Enabling And Disabling ParkSense ParkSensecan be enabled and disabled with
a switch located in the switch bank of the
instrument panel or through the Customer-
Programmable Features section of the EVIC.
The available choices are: OFF, Sound Only, or
Sound and Display. Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings
(Customer-Programmable Features)” in “Un-
derstanding Your Instrument Panel” for further
information.
When the ParkSense switch is
pressed to disable the system, the
instrument cluster will display the
“PARK ASSIST SYSTEM OFF”
message for approximately five
seconds. Refer to “Electronic Ve-
hicle Information Center (EVIC)” in “Under-
standing Your Instrument Panel” for further in- formation. When the shift lever is moved to
REVERSE or to DRIVE (at or below
11 mph/18 km/h) and the system is disabled,
the EVIC will display the “PARK ASSIST SYS-
TEM OFF” message for as long as the vehicle is
in REVERSE or for five seconds when the
vehicle is in DRIVE.
The ParkSense
switch LED will be ON when
ParkSense is disabled or defective. The Park-
Sense switch LED will be OFF when the
system is enabled.
134

on the Navigation/Multimedia radio display
screen along with a caution note to “check
entire surroundings” across the top of the
screen. After five seconds this note will disap-
pear. The ParkViewcamera is located on the
rear of the vehicle above the rear License plate. When the vehicle is shifted out of REVERSE, the
rear camera mode is exited and the navigation
or audio screen appears again.
When displayed, static grid lines will illustrate
the width of the vehicle while a dashed center-
line will indicate the center of the vehicle toassist with aligning to a hitch/receiver. The
static grid lines will show separate zones that
will help indicate the distance to the rear of the
vehicle. The following table shows the approxi-
mate distances for each zone:
Zone
Distance to the rear of the vehicle
Red 0-1ft(0-30cm)
Yellow 1 ft-3ft(30cm-1m)
Green 3 ft or greater (1 m or greater)
WARNING!
Drivers must be careful when backing up even
when using the ParkViewRear Back Up
Camera. Always check carefully behind your
vehicle, and be sure to check for pedestrians,
animals, other vehicles, obstructions, or blind
spots before backing up. You are responsible
for the safety of your surroundings and must
continue to pay attention while backing up.
Failure to do so can result in serious injury or
death.CAUTION!
• To avoid vehicle damage, ParkView 
should only be used as a parking aid. The
ParkView camera is unable to view every
obstacle or object in your drive path.
• To avoid vehicle damage, the vehicle must
be driven slowly when using ParkView to
be able to stop in time when an obstacle is
seen. It is recommended that the driver
look frequently over his/her shoulder when
using ParkView. NOTE:
If snow, ice, mud, or any foreign substance
builds up on the camera lens, clean the lens,
rinse with water, and dry with a soft cloth. Do
not cover the lens.
137