warning JEEP GRAND CHEROKEE 2013 Owner handbook (in English)

1
INTRODUCTION
•INTRODUCTION ...............................4
• ROLLOVER WARNING ...........................4
• IMPORTANT NOTICE ............................5
• HOW TO USE THIS MANUAL .......................6
• WARNINGS AND CAUTIONS .......................8
• VEHICLE IDENTIFICATION NUMBER ..................8
• VEHICLE MODIFICATIONS/ALTERATIONS ...............8
3

INTRODUCTION
Congratulations on selecting your new Chrysler
Group LLC vehicle. Be assured that it repre-
sents precision workmanship, distinctive styl-
ing, and high quality - all essentials that are
traditional to our vehicles.
This is a specialized utility vehicle. It can go
places and perform tasks that conventional
passenger cars are not intended. It handles and
maneuvers differently from many passenger
cars both on-road and off-road, so take time to
become familiar with your vehicle.
The two-wheel drive version of this vehicle was
designed for on-road use only. It is not intended
for off-road driving or use in other severe con-
ditions suited for a four-wheel drive vehicle.
Before you start to drive this vehicle, read the
Owner’s Manual and all the Supplements. Be
sure you are familiar with all vehicle controls,
particularly those used for braking, steering,
and transmission and transfer case shifting.
Learn how your vehicle handles on different
road surfaces. Your driving skills will improve
with experience, but as in driving any vehicle,take it easy as you begin. When driving off-road
or working the vehicle, don’t overload it or
expect it to overcome the forces of nature.
Always observe local laws wherever you drive.
As with other vehicles of this type, failure to
operate this vehicle correctly may result in loss
of control or a collision. Be sure to read the
“On-Road/ Off-Road Driving Tips” in “Starting
And Operating” for further information.
NOTE:
After reviewing the owner information, it
should be stored in the vehicle for conve-
nient referencing and remain with the ve-
hicle when sold.
Failure to operate this vehicle correctly may
result in loss of control or a collision.
Operating this vehicle at excessive speeds or
while intoxicated may result in loss of control,
collision with other vehicles or objects, going off
the road, or overturning; any of which may lead
to serious injury or death. Also, failure to use
seat belts subjects the driver and passengers to
a greater risk of injury or death.
To keep your vehicle running at its best, have
your vehicle serviced at recommended intervals
by an authorized dealer or distributor who has
the qualified personnel, special tools and equip-
ment to perform all service.
The manufacturer and its distributors are vitally
interested in your complete satisfaction with this
vehicle. If you encounter a service or warranty
problem which is not resolved to your satisfac-
tion, discuss the matter with your authorized
dealer or distributor’s management.
Your authorized dealer or distributor will be
happy to assist you with any questions about
your vehicle.
ROLLOVER WARNING
Utility vehicles have a significantly higher rollover
rate than other types of vehicles. This vehicle has a
higher ground clearance and a higher center of
gravity than many passenger cars. It is capable of
performing better in a wide variety of off-road
applications. Driven in an unsafe manner, all ve-
hicles can go out of control. Because of the higher
center of gravity, if this vehicle is out of control it
may roll over when some other vehicles may not.
4

Do not attempt sharp turns, abrupt maneuvers,
or other unsafe driving actions that can cause
loss of vehicle control. Failure to operate this
vehicle safely may result in a collision, rollover
of the vehicle, and severe or fatal injury. Drive
carefully.
Failure to use the driver and passenger seat
belts provided is a major cause of severe or
fatal injury. In a rollover crash, an unbelted
person is significantly more likely to die than a
person wearing a seat belt. Always buckle up.IMPORTANT NOTICE
ALL MATERIAL CONTAINED IN THIS PUBLI-
CATION IS BASED ON THE LATEST INFOR-
MATION AVAILABLE AT TIME OF PUBLICA-
TION APPROVAL. THE RIGHT IS RESERVED
TO PUBLISH REVISIONS AT ANY TIME.
This Owner’s Manual has been prepared with
the assistance of service and engineering spe-
cialists to acquaint you with the operation and
maintenance of your new vehicle. It is supple-
mented by a Warranty Information Booklet and
various customer-oriented documents. You are
urged to read these publications carefully. Fol-
lowing the instructions and recommendations in
this Owner’s Manual will help assure safe and
enjoyable operation of your vehicle.
After you have read the Owner’s Manual, it should
be stored in the vehicle for convenient reference
and remain with the vehicle when sold.
The manufacturer reserves the right to make
changes in design and specifications, and/or to
make additions to or improvements in its prod-
ucts without imposing any obligations upon
itself to install them on products previously
manufactured.The Owner’s Manual illustrates and describes
the features that are standard or available as
extra cost options. Therefore, some of the
equipment and accessories in this publication
may not appear on your vehicle.
NOTE:
Be sure to read the Owner’s Manual first
before driving your vehicle and before at-
taching or installing parts/accessories or
making other modifications to the vehicle.
In view of the many replacement parts and
accessories from various manufacturers avail-
able on the market, the manufacturer cannot be
certain that the driving safety of your vehicle will
not be impaired by the attachment or installation
of such parts. Even if such parts are officially-
approved (for example, by a general operating
permit for the part or by constructing the part in
an officially approved design), or if an individual
operating permit was issued for the vehicle after
the attachment or installation of such parts, it
cannot be implicitly assumed that the driving
safety of your vehicle is unimpaired. Therefore,
neither experts nor official agencies are liable.
Rollover Warning Label
5

WARNINGS AND CAUTIONS
This Owners Manual containsWARNINGS
against operating procedures that could result
in a collision or bodily injury. It also contains
CAUTIONS against procedures that could re-
sult in damage to your vehicle. If you do not
read this entire Owners Manual, you may miss
important information. Observe all Warnings
and Cautions.
VEHICLE IDENTIFICATION
NUMBER
The Vehicle Identification Number (VIN) is
found on a plate located on the left front corner
of the instrument panel pad, visible from outside
of the vehicle through the windshield. This num-
ber also is stamped into the right front body,
behind the right front seat. Move the right front
seat forward to allow better viewing of the
stamped VIN. NOTE:
It is illegal to remove or alter the VIN.
VEHICLE MODIFICATIONS/
ALTERATIONS
WARNING!
Any modifications or alterations to this ve-
hicle could seriously affect its roadworthi-
ness and safety and may lead to a collision
resulting in serious injury or death.
VIN Location
Right Front Body VIN Location
8

NOTE:You can insert the double-sided emergency
key into the lock cylinders with either side up.
Removing Key Fob From IgnitionPlace the shift lever in PARK. Turn the Key Fob to
the OFF position and then remove the Key Fob.
With the Keyless Enter-N-Go™ feature, the
EVIC will display the ignition switch position
“OFF/ACC/RUN”. Refer to “Electronic Vehicle
Information Center (EVIC)” in “Understanding
Your Instrument Panel” for further information.NOTE:
•
If you try to remove the Key Fob before
you place the shift lever in PARK, it may
become trapped temporarily in the igni-
tion switch. If this occurs, rotate the key
to the right slightly, then remove the Key
Fob as described. If a malfunction occurs,
the system will trap the key in the ignition
switch to warn you that this safety feature
is inoperable. The engine can be started
and stopped, but the Key Fob cannot be
removed until you obtain service.
•
The power window switches, radio, power
sunroof (if equipped), and power outlets will
remain active for up to 10 minutes after the
ignition switch is turned to the OFF position.
Opening either front door will cancel this
feature. The time for this feature is program-
mable. Refer to “Electronic Vehicle Informa-
tion Center (EVIC)/Personal Settings
(Customer-Programmable Features)” in “Un-
derstanding Your Instrument Panel” for fur-
ther information.
CAUTION!
• If your vehicle battery becomes low or
dead, your Key Fob will become locked in
the ignition.
• Do not attempt to remove the Key Fob
while in this condition, damage could occur
to the Key Fob or ignition module. Only
remove the emergency key for locking and
unlocking the doors.
• Leave the Key Fob in the ignition and
either:
• Jump Start the vehicle.
• Charge the battery.
WARNING!
•When leaving the vehicle, always remove
the Key Fob from the vehicle and lock your
vehicle.
• Never leave children alone in a vehicle, or
with access to an unlocked vehicle.
(Continued)
Emergency Key Removal
13

WARNING!(Continued)
•Allowing children to be in a vehicle unat-
tended is dangerous for a number of rea-
sons. A child or others could be seriously or
fatally injured. Children should be warned
not to touch the parking brake, brake pedal
or the shift lever.
•Do not leave the Key Fob in or near the
vehicle, or in a location accessible to chil-
dren, and do not leave a vehicle equipped
with Keyless Enter-N-Go™ in the ACC or
ON/RUN mode. A child could operate
power windows, other controls, or move
the vehicle.
• Do not leave children or animals inside
parked vehicles in hot weather. Interior
heat build-up may cause serious injury or
death.
CAUTION!
An unlocked car is an invitation to thieves.
Always remove Key Fob from the ignition
and lock all doors when leaving the vehicle
unattended.
Key-In-Ignition ReminderOpening the driver’s door when the Key Fob is
in the ignition and the ignition switch position is
OFF or ACC, sounds a signal to remind you to
remove the Key Fob.
NOTE:
The Key-In-Ignition reminder only sounds
when the Key Fob is placed in the OFF or
ACC ignition position.
With the Keyless Enter-N-Go™ feature, open-
ing the driver’s door when the vehicle’s ignition
switch is placed in ACC or ON/RUN (engine
stopped) will cause the reminder chime to
sound. Refer to “Starting Procedures” in “Start-
ing And Operating” for further information.
STEERING WHEEL LOCK — IF
EQUIPPED
Your vehicle may be equipped with a passive
electronic steering wheel lock. This lock pre-
vents steering the vehicle without the ignition
key. The steering wheel lock has six positions
(one every 60 degrees). If the steering wheel is
moved to one of these six position with the key
in the off positions, the steering wheel will lock.
To Manually Lock The Steering WheelWith the engine running, rotate the steering
wheel one-half revolution in either direction
(three o’clock or nine o’clock position), turn off
the engine and remove the key. Turn the steer-
ing wheel slightly in either direction until the lock
engages.
14

WARNING!
•For personal security and safety in the
event of a collision, lock the vehicle doors
before you drive as well as when you park
and leave the vehicle.
•
When leaving the vehicle, always remove
the Key Fob from the vehicle and lock your
vehicle. Unsupervised use of vehicle equip-
ment may cause severe personal injuries or
death.
•Never leave children alone in a vehicle, or
with access to an unlocked vehicle. Allowing
children to be in a vehicle unattended is
dangerous for a number of reasons. A child
or others could be seriously or fatally injured.
Children should be warned not to touch the
parking brake, brake pedal or the shift lever.
•Do not leave the Key Fob in or near the
vehicle, or in a location accessible to children,
and do not leave a vehicle equipped with
Keyless Enter-N-Go™ in the ACC or ON/RUN
mode. A child could operate power windows,
other controls, or move the vehicle.
Power Door LocksThe power door lock switch is located on each
front door panel. Press the switch to lock or
unlock the doors.
If the lock knob is down when the door is closed,
the door will lock. Therefore, make sure the Key
Fob is not inside the vehicle before closing the
door.
If you press the door lock switch while the Key
Fob is in the ignition switch and the driver’s door
is open, the doors will not lock. If a rear door is locked, it cannot be opened from
inside the vehicle without first unlocking the
door. The door may be unlocked manually by
raising the lock knob.
Automatic Door Locks — If Equipped
The auto door lock feature default condition is
enabled. When enabled, the door locks will lock
automatically when the vehicle’s speed ex-
ceeds 15 mph (24 km/h). The auto door lock
feature can be enabled or disabled by your
authorized dealer per written request of the
customer. Please see your authorized dealer for
service.
Automatic Unlock On Exit Feature — If
Equipped
If Auto Unlock is enabled, this feature will unlock
all the doors when the driver’s door is opened if
the vehicle is stopped and in PARK or NEU-
TRAL. Refer to “Electronic Vehicle Information
Center (EVIC)/Personal Settings (Customer-
Programmable Features)” in “Understanding
Your Instrument Panel” for further information.
Power Door Lock Switch
22

Child-Protection Door Lock
System — Rear Doors
To provide a safer environment for small children
riding in the rear seats, the rear doors are equipped
with Child-Protection Door Lock system.
To Engage Or Disengage The
Child-Protection Door Lock System
1. Open the rear door.
2.
Insert the tip of the emergency key into the
lock and rotate to the LOCK or UNLOCK position.
3. Repeat steps 1 and 2 for the opposite rear
door.WARNING!
Avoid trapping anyone in a vehicle in a
collision. Remember that the rear doors can
only be opened from the outside when the
Child-Protection locks are engaged (locked).
NOTE:
For emergency exit from the rear seats when
the Child-Protection Door Lock System is
engaged, manually raise the door lock knob
to the unlocked position, roll down the win-
dow, and open the door using the outside
door handle.
KEYLESS ENTER-N-GO™
The Passive Entry system is an enhancement
to the vehicle’s Remote Keyless Entry (RKE)
system and a feature of Keyless Enter-N-Go™.
This feature allows you to lock and unlock the
vehicle’s door(s) without having to press the
RKE transmitter lock or unlock buttons.
NOTE:
•
Passive Entry may be programmed ON/
OFF; refer to “Electronic Vehicle Informa-
tion Center (EVIC)/Personal Settings
(Customer-Programmable Features)” in
“Understanding Your Instrument Panel” for
further information.
• If a Passive Entry door handle has not
been used for 72 hours, the Passive Entry
feature for the handle may time out. Pull-
ing the deactivated front door handle will
reactivate the door handle’s Passive En-
try feature.
•
If wearing gloves on your hands, or if it has
been raining on the Passive Entry door
handle, the unlock sensitivity can be af-
fected, resulting in a slower response time.
Child-Protection Door Lock Location
Child-Protection Door Lock Function
23

NOTE:
•After pressing the door handle LOCK but-
ton, you must wait two seconds before
you can lock or unlock the doors, using
either Passive Entry door handle. This is
done to allow you to check if the vehicle is
locked by pulling the door handle, without
the vehicle reacting and unlocking.
• The Passive Entry system will not operate
if the RKE transmitter battery is dead.
The vehicle doors can also be locked by using
the RKE transmitter lock button or the lock
button located on the vehicle’s interior door
panel.WINDOWS
Power WindowsThe power window controls are located on the
driver’s door trim panel. There is a single switch
on the front passenger door and rear doors
which operate the front passenger and rear
passenger door windows. The window controls
will operate only when the ignition switch is in
the ON/RUN or ACC position.
The power window switches remain active for
up to 10 minutes after the ignition switch has
been turned OFF. Opening a vehicle front door
will cancel this feature.
WARNING!
Never leave children unattended in a vehicle,
and do not let children play with power
windows. Do not leave the key fob in or near
the vehicle, and do not leave a vehicle
equipped with Keyless Enter-N-Go™ in the
ACC or ON/RUN mode. Occupants, particu-
larly unattended children, can become en-
trapped by the windows while operating the
power window switches. Such entrapment
may result in serious injury or death.
Auto-Down
Both the driver and front passenger window
switches have an “Auto-Down” feature. Press
the window switch past the first detent, release,
and the window will go down automatically. To
cancel the “Auto-Down” movement, operate the
switch in either the up or down direction and
release the switch.
Power Window Switches
26

To open the window part way, press to the first
detent and release it when you want the window
to stop.
Auto Up Feature With Anti-Pinch Protection —
Driver And Front Passenger Door Only
Lift the window switch fully upward to the sec-
ond detent, release, and the window will go up
automatically.
To stop the window from going all the way up
during the Auto Up operation, push down on the
switch briefly.To close the window part way, lift the window
switch to the first detent and release when you
want the window to stop.
NOTE:If the window runs into any obstacle during
Auto Up it will reverse direction and then go
back down. Remove the obstacle and use the
window switch again to close the window. Any
impact due to rough road conditions may
trigger the auto reverse function unexpectedly
during Auto Up. If this happens, pull the
switch lightly to the first detent and hold it to
close the window manually.
WARNING!
There is no anti-pinch protection when the
window is almost closed. Be sure to clear all
objects from the window before closing.
Resetting The Auto Up Feature
Should the Auto Up feature stop working, the
window probably needs to be reset. To reset
Auto Up:
1. Pull the window switch up to close the win-
dow completely and continue to hold the switch
up for an additional two seconds after the
window is closed.
2. Push the window switch down firmly to the
second detent to open the window completely
and continue to hold the switch down for an
additional two seconds after the window is fully
open.
Auto Down Window SwitchesAuto Up Window Switches
27