check engine light JEEP LIBERTY 2002 KJ / 1.G Repair Manual
[x] Cancel search | Manufacturer: JEEP, Model Year: 2002, Model line: LIBERTY, Model: JEEP LIBERTY 2002 KJ / 1.GPages: 1803, PDF Size: 62.3 MB
Page 1734 of 1803
The pump contains a 3 port solenoid, a pump that
contains a switch, a spring loaded canister vent valve
seal, 2 check valves and a spring/diaphragm.
OPERATION
Immediately after a cold start, engine temperature
between 40ÉF and 86ÉF, the 3 port solenoid is briefly
energized. This initializes the pump by drawing air
into the pump cavity and also closes the vent seal.
During non-test test conditions, the vent seal is held
open by the pump diaphragm assembly which pushes
it open at the full travel position. The vent seal will
remain closed while the pump is cycling. This is due
to the operation of the 3 port solenoid which prevents
the diaphragm assembly from reaching full travel.
After the brief initialization period, the solenoid is
de-energized, allowing atmospheric pressure to enter
the pump cavity. This permits the spring to drive the
diaphragm which forces air out of the pump cavity
and into the vent system. When the solenoid is ener-
gized and de-energized, the cycle is repeated creating
flow in typical diaphragm pump fashion. The pump
is controlled in 2 modes:
PUMP MODE:The pump is cycled at a fixed rate
to achieve a rapid pressure build in order to shorten
the overall test time.
TEST MODE:The solenoid is energized with a
fixed duration pulse. Subsequent fixed pulses occur
when the diaphragm reaches the switch closure
point.
The spring in the pump is set so that the system
will achieve an equalized pressure of about 7.5 inches
of water.
When the pump starts, the cycle rate is quite high.
As the system becomes pressurized pump rate drops.
If there is no leak the pump will quit. If there is a
leak, the test is terminated at the end of the test
mode.
If there is no leak, the purge monitor is run. If the
cycle rate increases due to the flow through the
purge system, the test is passed and the diagnostic is
complete.
The canister vent valve will unseal the system
after completion of the test sequence as the pump
diaphragm assembly moves to the full travel position.
REMOVAL
The Leak Detection Pump (LDP) is attached (bolt-
ed) to the front of the fuel tank (Fig. 3). The LDP
fresh air filter is located on the end of a hose. This
hose is attached to the fuel fill tube assembly below
and near the fuel fill opening (Fig. 1). The LDP and
LDP filter are typically replaced (serviced) as one
unit.
(1) Raise vehicle.(2) Carefully remove two 3/4º vent hoses at sides
of LDP.
(3) Carefully remove other vapor/vacuum hoses
from LDP.
(4) Place a hydraulic jack under fuel tank.
(5) Loosen 2 fuel tank strap mounting bolts at
front of tank about 10 turns.
(6) Lower front of fuel tank about 1/2º.
(7) Remove 2 LDP mounting nuts (Fig. 3) and
lower LDP slightly to gain access to electrical connec-
tor (Fig. 4).
(8) Disconnect electrical connector at LDP. To dis-
connect: Slide red colored tab upward. Push on black
colored tab while removing connector.
(9) Remove LDP from vehicle.
INSTALLATION
The Leak Detection Pump (LDP) is attached (bolt-
ed) to the front of the fuel tank. The LDP filter is
located on the end of a hose. This hose is attached to
the fuel fill tube assembly below and near the fuel
fill opening. The LDP and LDP filter are replaced
(serviced) as one unit.
(1) Install electrical connector to LDP. Push red
colored tab downward to lock connector to LDP.
(2) Position LDP and LDP bracket to fuel tank
mounting studs and install 2 nuts. Tighten nuts to 1
N´m (11 in. lbs.) torque.
(3) Raise fuel tank to body and tighten 2 strap
bolts to 61 N´m (45 ft. lbs.) torque.
Fig. 3 LDP LOCATION / MOUNTING
1 - LDP
2 - FLOW MANAGEMENT VALVE
3 - MOUNTING NUTS
4 - FRONT OF FUEL TANK
25 - 28 EVAPORATIVE EMISSIONSKJ
LEAK DETECTION PUMP (Continued)
Page 1737 of 1803
OPERATION
The PCV system operates by engine intake mani-
fold vacuum. Filtered air is routed into the crankcase
through the air cleaner hose and crankcase breath-
er(s) (if used). The metered air, along with crankcase
vapors, are drawn through the PCV valve and into a
passage in the intake manifold. The PCV system
manages crankcase pressure and meters blow-by
gases to the intake system, reducing engine sludge
formation.
The PCV valve contains a spring loaded plunger.
This plunger meters the amount of crankcase vapors
routed into the combustion chamber based on intake
manifold vacuum.
TYPICALPCV valves are shown in (Fig. 9), (Fig.
10) and (Fig. 11).
When the engine is not operating, or during an
engine pop-back, the spring forces the plunger back
against the seat (Fig. 9). This will prevent vapors
from flowing through the valve.
During periods of high manifold vacuum, such as
idle or cruising speeds, vacuum is sufficient to com-
pletely compress spring. It will then pull the plunger
to the top of the valve (Fig. 10). In this position there
is minimal vapor flow through the valve.
During periods of moderate manifold vacuum, the
plunger is only pulled part way back from inlet. This
results in maximum vapor flow through the valve
(Fig. 11).
DIAGNOSIS AND TESTING - PCV VALVE
3.7L
(1) Disconnect PCV line/hose (Fig. 7) by discon-
necting rubber connecting hose at PCV valve fitting.
(2) Remove PCV valve at oil filler tube by rotating
PCV valve downward until locating tabs have been
freed at cam lock (Fig. 7). After tabs have cleared,
pull valve straight out from filler tube.To prevent
damage to PCV valve locating tabs, valve must
be pointed downward for removal. Do not force
valve from oil filler tube.
(3) After valve is removed, check condition of valve
o-ring (Fig. 7). Also, PCV valve should rattle when
shaken.
(4) Reconnect PCV valve to its connecting line/
hose.
(5) Start engine and bring to idle speed.
(6) If valve is not plugged, a hissing noise will be
heard as air passes through valve. Also, a strong vac-
uum should be felt with a finger placed at valve
inlet.
(7) If vacuum is not felt at valve inlet, check line/
hose for kinks or for obstruction. If necessary, clean
out intake manifold fitting at rear of manifold. Do
this by turning a 1/4 inch drill (by hand) through the
fitting to dislodge any solid particles. Blow out the
fitting with shop air. If necessary, use a smaller drill
to avoid removing any metal from the fitting.
(8)Do not attempt to clean the old PCV valve.
(9) Return PCV valve back to oil filler tube by
placing valve locating tabs (Fig. 7) into cam lock.
Press PCV valve in and rotate valve upward. A slight
click will be felt when tabs have engaged cam lock.
Valve should be pointed towards rear of vehicle.
(10) Connect PCV line/hose and connecting rubber
hose to PCV valve.
(11) Disconnect rubber hose from fresh air fitting
at air cleaner resonator box. Start engine and bring
to idle speed. Hold a piece of stiff paper (such as a
parts tag) loosely over the opening of the discon-
nected rubber hose.
(12) The paper should be drawn against the hose
opening with noticeable force. This will be after
allowing approximately one minute for crankcase
pressure to reduce.
Fig. 9 Engine Off or Engine Pop-BackÐNo Vapor
Flow
Fig. 10 High Intake Manifold VacuumÐMinimal
Vapor Flow
Fig. 11 Moderate Intake Manifold VacuumÐ
Maximum Vapor Flow
KJEVAPORATIVE EMISSIONS 25 - 31
PCV VALVE (Continued)
Page 1748 of 1803
ENGINE - DESCRIPTION, COOLING
SYSTEM 3.7L.........................7-1
ENGINE - DESCRIPTION, COOLING
SYSTEM ROUTING 3.7L.................7-2
ENGINE - INSTALLATION, 3.7L . . . 7-17,7-18,7-22
ENGINE - REMOVAL, 3.7L...........7-17,7-21
ENGINE - STANDARD PROCEDURE,
DRAINING COOLING SYSTEM 3.7L........7-12
ENGINE - STANDARD PROCEDURE,
REFILLING COOLING SYSTEM 3.7L.......7-12
ENGINE BLOCK - CLEANING.............9-39
ENGINE BLOCK - DESCRIPTION..........9-39
ENGINE BLOCK - INSPECTION...........9-40
ENGINE COOLANT - DESCRIPTION.........0-3
ENGINE COOLANT TEMPERATURE
SENSOR - DESCRIPTION...............7-19
ENGINE COOLANT TEMPERATURE
SENSOR - INSTALLATION...............7-21
ENGINE COOLANT TEMPERATURE
SENSOR - OPERATION.................7-20
ENGINE COOLANT TEMPERATURE
SENSOR - REMOVAL...................7-20
ENGINE COOLANT THERMOSTAT -
OPERATION..........................7-21
ENGINE CORE AND OIL GALLERY PLUGS
- STANDARD PROCEDURE..............9-10
ENGINE CRADLE CROSSMEMBER -
INSTALLATION........................13-6
ENGINE CRADLE CROSSMEMBER -
REMOVAL...........................13-6
ENGINE DIAGNOSIS - INTRODUCTION -
DIAGNOSIS AND TESTING.................9-4
ENGINE DIAGNOSIS - LUBRICATION -
DIAGNOSIS AND TESTING...............9-7
ENGINE DIAGNOSIS - MECHANICAL -
DIAGNOSIS AND TESTING...............9-6
ENGINE DIAGNOSIS - PERFORMANCE -
DIAGNOSIS AND TESTING...............9-4
ENGINE FIRING ORDER, 2.4L 4-
CYLINDER...........................8I-2
ENGINE FIRING ORDER, 3.7L V-6.........8I-2
ENGINE GASKET SURFACE
PREPARATION - STANDARD
PROCEDURE..........................9-9
ENGINE OIL - STANDARD PROCEDURE....9-61
ENGINE OIL LEAK - DIAGNOSIS AND
TESTING............................9-60
ENGINE OIL PRESSURE - DIAGNOSIS
AND TESTING........................9-60
ENGINE, SPECIAL TOOLS - 3.7L..........9-15
ENGINE, SPECIFICATIONS - 3.7L.........9-12
ENGINE TEMPERATURE GAUGE -
DESCRIPTION.......................8J-18
ENGINE TEMPERATURE GAUGE -
OPERATION.........................8J-18
ENGINES - GENERATOR RATINGS, GAS . . . 8F-23
ENTRY MODULE - DESCRIPTION,
REMOTE KEYLESS....................8N-7
ENTRY MODULE - DIAGNOSIS AND
TESTING, REMOTE KEYLESS............8N-7
ENTRY MODULE - INSTALLATION,
REMOTE KEYLESS....................8N-7
ENTRY MODULE - OPERATION, REMOTE
KEYLESS............................8N-7
ENTRY MODULE - REMOVAL, REMOTE
KEYLESS............................8N-7
ENTRY TRANSMITTER - DIAGNOSIS AND
TESTING, REMOTE KEYLESS............8N-8
ENTRY TRANSMITTER -
SPECIFICATIONS, REMOTE KEYLESS......8N-9
EQUIPMENT - STANDARD PROCEDURE,
REFRIGERANT SYSTEM SERVICE........24-40
ERASING TRANSMITTER CODES -
STANDARD PROCEDURE...............8M-8
EVACUATE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-41
EVAPORATION CONTROL SYSTEM -
DESCRIPTION.......................25-24
EVAPORATOR - DESCRIPTION, A/C.......24-49
EVAPORATOR - INSTALLATION, A/C......24-49
EVAPORATOR - OPERATION, A/C........24-49
EVAPORATOR - REMOVAL, A/C..........24-49
EVAP/PURGE SOLENOID - DESCRIPTION . . 25-27
EVAP/PURGE SOLENOID - INSTALLATION
. 25-27
EVAP/PURGE SOLENOID - OPERATION
....25-27
EVAP/PURGE SOLENOID - REMOVAL
.....25-27
EXCEPT DIESEL - TORQUE
.............8F-23
EXHAUST MANIFOLD - DESCRIPTION
.....9-69EXHAUST MANIFOLD - INSTALLATION.....9-70
EXHAUST MANIFOLD - REMOVAL.........9-69
EXHAUST SYSTEM - DESCRIPTION.......11-1
EXHAUST SYSTEM - DIAGNOSIS AND
TESTING............................11-2
EXTENSION HOUSING BUSHING -
NV3550 - INSTALLATION...............21-74
EXTENSION HOUSING BUSHING -
NV3550 - REMOVAL..................21-73
EXTENSION HOUSING SEAL - NV1500 -
INSTALLATION.......................21-32
EXTENSION HOUSING SEAL - NV1500 -
REMOVAL..........................21-32
EXTENSION HOUSING SEAL - NV3550 -
INSTALLATION.......................21-74
EXTENSION HOUSING SEAL - NV3550 -
REMOVAL..........................21-74
EXTERIOR - DESCRIPTION, LAMPS/
LIGHTING...........................8L-2
EXTERIOR - DIAGNOSIS AND TESTING,
LAMPS/LIGHTING.....................8L-7
EXTERIOR - OPERATION, LAMPS/
LIGHTING...........................8L-5
EXTERIOR - SPECIFICATIONS,
LAMPS/LIGHTING....................8L-15
EXTERIOR HANDLE - INSTALLATION....23-123,
23-130,23-136
EXTERIOR HANDLE - REMOVAL . 23-123,23-130,
23-136
EXTERIOR NAME PLATES -
INSTALLATION......................23-141
EXTERIOR NAME PLATES - REMOVAL . . . 23-140
FAN - ELECTRIC - DESCRIPTION,
RADIATOR...........................7-26
FAN - ELECTRIC - INSTALLATION,
RADIATOR...........................7-27
FAN - ELECTRIC - OPERATION,
RADIATOR...........................7-26
FAN - ELECTRIC - REMOVAL, RADIATOR . . . 7-26
FAN - VISCOUS - CLEANING, RADIATOR . . . 7-29
FAN - VISCOUS - DESCRIPTION,
RADIATOR...........................7-27
FAN - VISCOUS - INSPECTION,
RADIATOR...........................7-29
FAN - VISCOUS - INSTALLATION,
RADIATOR...........................7-29
FAN - VISCOUS - OPERATION,
RADIATOR...........................7-27
FAN - VISCOUS - REMOVAL, RADIATOR....7-28
FAN DRIVE - DIAGNOSIS AND TESTING,
VISCOUS............................7-28
FASCIA - INSTALLATION, FRONT.........13-2
FASCIA - INSTALLATION, REAR..........13-2
FASCIA - REMOVAL, FRONT.............13-1
FASCIA - REMOVAL, REAR..............13-2
FASCIA SUPPORT - INSTALLATION,
REAR...............................13-3
FASCIA SUPPORT - REMOVAL, REAR......13-3
FASTENER IDENTIFICATION -
DESCRIPTION......................Intro.-1
FENDER - INSTALLATION, FRONT.......23-141
FENDER - REMOVAL, FRONT..........23-141
FILL - STANDARD PROCEDURE, FLUID
DRAIN......................21-208,21-246
FILL - STANDARD PROCEDURE,
TRANSMISSION.....................21-128
FILL DOOR/HOUSING - INSTALLATION,
FUEL.............................23-141
FILL DOOR/HOUSING - REMOVAL, FUEL . 23-141
FILL/CHECK LOCATIONS - DESCRIPTION,
FLUID...............................0-4
FILLER CAP - DESCRIPTION, FUEL.......25-27
FILLER CAP - OPERATION, FUEL........25-27
FILTER - DESCRIPTION, FUEL............14-7
FILTER - INSTALLATION, FUEL...........14-8
FILTER - INSTALLATION, INLET..........14-28
FILTER - INSTALLATION, OIL............9-63
FILTER - REMOVAL, FUEL...............14-7
FILTER - REMOVAL, INLET.............14-28
FILTER - REMOVAL, OIL
................9-63
FILTER REPLACEMENT - STANDARD
PROCEDURE, FLUID
.................21-126
FINESSE SANDING/BUFFING &
POLISHING - DESCRIPTION
...........23-163
FINISH - DESCRIPTION, BASE
COAT/CLEAR COAT
..................23-162
FIRING ORDER, 2.4L 4-CYLINDER -
ENGINE
..............................8I-2FIRING ORDER, 3.7L V-6 - ENGINE........8I-2
FITTING - CONNECTING ROD BEARING....9-49
FITTING - DESCRIPTION, QUICK
CONNECT...........................14-10
FITTING - MAIN BEARING...............9-45
FITTING - STANDARD PROCEDURE,
CONNECTING ROD BEARING............9-40
FITTING - STANDARD PROCEDURE,
PISTON.............................9-50
FITTING - STANDARD PROCEDURE,
PISTON RING........................9-52
FITTINGS - STANDARD PROCEDURE,
QUICK-CONNECT.....................14-10
FLARE MOLDINGS - INSTALLATION,
FRONT WHEEL OPENING.............23-145
FLARE MOLDINGS - INSTALLATION,
REAR WHEEL OPENING..............23-145
FLARE MOLDINGS - REMOVAL, FRONT
WHEEL OPENING...................23-145
FLARE MOLDINGS - REMOVAL, REAR
WHEEL OPENING...................23-145
FLARING - STANDARD PROCEDURE,
DOUBLE INVERTED.....................5-8
FLARING - STANDARD PROCEDURE, ISO....5-8
FLASHER - DESCRIPTION, COMBINATION . 8L-19
FLASHER - OPERATION, COMBINATION . . . 8L-19
FLEX PLATE - INSTALLATION............9-49
FLEX PLATE - REMOVAL................9-49
FLIP-UP GLASS - INSTALLATION.......23-136
FLIP-UP GLASS - REMOVAL...........23-136
FLIP-UP GLASS AJAR SWITCH -
DESCRIPTION.......................8L-77
FLIP-UP GLASS AJAR SWITCH -
OPERATION.........................8L-77
FLIP-UP GLASS LATCH - INSTALLATION . 23-136
FLIP-UP GLASS LATCH - REMOVAL.....23-136
FLIP-UP GLASS RELEASE SWITCH -
DIAGNOSIS AND TESTING..............8N-5
FLIP-UP GLASS SUPPORT CYLINDER -
INSTALLATION......................23-139
FLIP-UP GLASS SUPPORT CYLINDER -
REMOVAL.........................23-139
FLOOR - DEFROST DOO - INSTALLATION . . 24-37
FLOOR - DEFROST DOOR - REMOVAL....24-36
FLOOR - DEFROST DOOR ACTUATOR -
INSTALLATION.......................24-25
FLOOR - DEFROST DOOR ACTUATOR -
REMOVAL..........................24-24
FLOOR CONSOLE - INSTALLATION......23-158
FLOOR CONSOLE - REMOVAL..........23-158
FLOOR CONSOLE DUCT - INSTALLATION . . 24-31
FLOOR CONSOLE DUCT - REMOVAL.....24-31
FLOOR CONSOLE LID LATCH -
INSTALLATION......................23-158
FLOOR CONSOLE LID LATCH - REMOVAL . 23-158
FLOOR DUCT - INSTALLATION..........24-32
FLOOR DUCT - REMOVAL..............24-32
FLOOR MATS - INSTALLATION, CARPETS . 23-158
FLOOR MATS - REMOVAL, CARPETS....23-158
FLOOR SHIFT BOOT - INSTALLATION,
4WD .............................23-156
FLOOR SHIFT BOOT - REMOVAL, 4WD . . . 23-156
FLOW AND PRESSURE - DIAGNOSIS
AND TESTING, POWER STEERING........19-3
FLOW MANAGEMENT VALVE -
DESCRIPTION........................14-6
FLOW MANAGEMENT VALVE -
INSTALLATION........................14-7
FLOW MANAGEMENT VALVE -
OPERATION..........................14-6
FLOW MANAGEMENT VALVE - REMOVAL . . . 14-6
FLUID - DESCRIPTION, AUTOMATIC
TRANSMISSION.......................0-2
FLUID - DIAGNOSIS AND TESTING,
CAUSES OF BURNT..................21-125
FLUID - OPERATION, AUTOMATIC
TRANSMISSION.......................0-4
FLUID AND FILTER REPLACEMENT -
STANDARD PROCEDURE..............21-126
FLUID CAPACITIES - SPECIFICATIONS......0-4
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING......................21-125
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING, BRAKE
..................5-26
FLUID COOLER - DESCRIPTION
.........19-20
FLUID COOLER - INSTALLATION
.........19-20
FLUID COOLER - OPERATION
...........19-20
FLUID COOLER - REMOVAL
............19-20
KJINDEX 9
Description Group-Page Description Group-Page Description Group-Page
Page 1754 of 1803
LATCH - ACCESS PANEL - REMOVAL....23-139
LATCH - INSTALLATION . . 23-120,23-124,23-131,
23-137
LATCH - INSTALLATION, FLIP-UP GLASS . 23-136
LATCH - INSTALLATION, FLOOR
CONSOLE LID......................23-158
LATCH - INSTALLATION, GLOVE BOX....23-148
LATCH / LOCK - INSTALLATION,
FOLDING REAR SEAT BACK...........23-170
LATCH / LOCK - REMOVAL, FOLDING
REAR SEAT BACK...................23-170
LATCH - REMOVAL......23-120,23-124,23-131,
23-137
LATCH - REMOVAL, FLIP-UP GLASS.....23-136
LATCH - REMOVAL, FLOOR CONSOLE
LID...............................23-158
LATCH - REMOVAL, GLOVE BOX........23-148
LATCH RELEASE CABLE - INSTALLATION . 23-120
LATCH RELEASE CABLE - REMOVAL....23-120
LATCH RELEASE HANDLE -
INSTALLATION......................23-120
LATCH RELEASE HANDLE - REMOVAL . . . 23-120
LATCH STRIKER - INSTALLATION......23-124,
23-132,23-137
LATCH STRIKER - INSTALLATION, GLOVE
BOX ..............................23-149
LATCH STRIKER - INSTALLATION, REAR
SEAT BACK........................23-171
LATCH STRIKER - REMOVAL....23-124,23-132,
23-137
LATCH STRIKER - REMOVAL, GLOVE
BOX ..............................23-148
LATCH STRIKER - REMOVAL, REAR
SEAT BACK........................23-170
LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING FLUID...........21-80
LEAK - DIAGNOSIS AND TESTING,
ENGINE OIL..........................9-60
LEAK DETECTION PUMP - DESCRIPTION . . 25-27
LEAK DETECTION PUMP - INSTALLATION . 25-28
LEAK DETECTION PUMP - OPERATION....25-28
LEAK DETECTION PUMP - REMOVAL.....25-28
LEAK DOWN TEST - DIAGNOSIS AND
TESTING, FUEL PRESSURE..............14-3
LEAKAGE - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE.......9-8
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-4
LEAKS - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD....................9-68
LEAKS - DIAGNOSIS AND TESTING,
REAR SEAL AREA.....................9-61
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-2
LEAKS - STANDARD PROCEDURE,
REPAIRING..........................22-8
LEARN - STANDARD PROCEDURE, TCM
QUICK.............................8E-21
LEFT POWER SEAT SWITCH -
DESCRIPTION.......................8N-16
LEFT POWER SEAT SWITCH -
DIAGNOSIS AND TESTING.............8N-17
LEFT POWER SEAT SWITCH -
INSTALLATION......................8N-18
LEFT POWER SEAT SWITCH -
OPERATION
.........................8N-17
LEFT POWER SEAT SWITCH - REMOVAL
. . 8N-18
LEFT SIDE - INSTALLATION
.........2-12,2-15
LEFT SIDE - REMOVAL
.............2-11,2-15
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID
........21-125
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL
...................24-54
LEVEL - STANDARD PROCEDURES,
MASTER CYLINDER FLUID
..............5-26
LEVEL CHECK - STANDARD
PROCEDURE, FLUID
.................21-126
LEVEL SENDING UNIT - DIAGNOSIS AND
TESTING, FUEL
.......................14-9
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL
...................14-9
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL
.................14-10
LEVEL SENDING UNIT / SENSOR -
OPERATION, FUEL
.....................14-9
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL
......................14-9LEVEL SWITCH - DESCRIPTION,
WASHER FLUID.....................8R-17
LEVEL SWITCH - INSTALLATION,
WASHER FLUID.....................8R-18
LEVEL SWITCH - OPERATION, WASHER
FLUID.............................8R-17
LEVEL SWITCH - REMOVAL, WASHER
FLUID.............................8R-17
LEVELING MOTOR - DESCRIPTION,
HEADLAMP.........................8L-35
LEVELING MOTOR - INSTALLATION,
HEADLAMP.........................8L-36
LEVELING MOTOR - OPERATION,
HEADLAMP.........................8L-36
LEVELING MOTOR - REMOVAL,
HEADLAMP.........................8L-36
LEVELING SWITCH - DESCRIPTION,
HEADLAMP.........................8L-37
LEVELING SWITCH - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-37
LEVELING SWITCH - INSTALLATION,
HEADLAMP.........................8L-38
LEVELING SWITCH - OPERATION,
HEADLAMP.........................8L-37
LEVELING SWITCH - REMOVAL,
HEADLAMP.........................8L-38
LEVER - INSTALLATION................5-31
LEVER - INSTALLATION, SHIFT . . . 21-214,21-249
LEVER - REMOVAL....................5-31
LEVER - REMOVAL, SHIFT......21-213,21-248
LHD - INSTALLATION...............8W-97-6
LHD - REMOVAL....................8W-97-5
LICENSE PLATE LAMP BULB -
INSTALLATION.......................8L-45
LICENSE PLATE LAMP BULB - REMOVAL . . 8L-44
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-46
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-45
LID LATCH - INSTALLATION, FLOOR
CONSOLE..........................23-158
LID LATCH - REMOVAL, FLOOR
CONSOLE..........................23-158
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-2
LIGHTER OUTLET - DIAGNOSIS AND
TESTING, CIGAR...................8W-97-2
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIMITS - DESCRIPTION, HIGH AND LOW . . 25-20
LINE - DESCRIPTION, REFRIGERANT.....24-38
LINE - INSTALLATION, A/C DISCHARGE . . . 24-47
LINE - INSTALLATION, A/C LIQUID.......24-47
LINE - INSTALLATION, A/C SUCTION.....24-49
LINE - REMOVAL, A/C DISCHARGE.......24-46
LINE - REMOVAL, A/C LIQUID...........24-47
LINE - REMOVAL, A/C SUCTION.........24-48
LINE AND HOSES - DIAGNOSIS AND
TESTING, BRAKE.......................5-8
LINE PRESSURE (LP) SENSOR -
DESCRIPTION......................21-144
LINE PRESSURE (LP) SENSOR -
INSTALLATION......................21-144
LINE PRESSURE (LP) SENSOR -
OPERATION........................21-144
LINE PRESSURE (LP) SENSOR -
REMOVAL.........................21-144
LINES - DESCRIPTION, BRAKE............5-8
LINES - DESCRIPTION, FUEL...........14-10
LINES - DESCRIPTION, VACUUM........25-33
LINK - INSTALLATION, STABILIZER.......2-14
LINK - REMOVAL, STABILIZER...........2-14
LINK CONNECTOR - DESCRIPTION, DATA . 8E-10
LINK CONNECTOR - OPERATION, DATA . . . 8E-10
LINKAGE - INSTALLATION................6-9
LINKAGE - REMOVAL...................6-8
LINKAGE - STANDARD PROCEDURE,
STEERING..........................19-16
LIQUID LINE - INSTALLATION, A/C.......24-47
LIQUID LINE - REMOVAL, A/C...........24-47
LOAD TEST - STANDARD PROCEDURE....8F-12
LOAD VALUE - DESCRIPTION
...........25-20
LOADS - STANDARD PROCEDURE,
TESTING FOR A SHORT TO GROUND
ON FUSES POWERING SEVERAL
......8W-01-9
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE
...................8W-91-1
LOCATIONS - DESCRIPTION, FLUID
FILL/CHECK
...........................0-4
LOCATIONS - SPECIFICATIONS, SEALER
. . 23-87LOCATIONS - SPECIFICATIONS, WELD
AND STRUCTURAL ADHESIVE...........23-9
LOCK - INSTALLATION, FOLDING REAR
SEAT BACK LATCH..................23-170
LOCK - REMOVAL, FOLDING REAR SEAT
BACK LATCH.......................23-170
LOCK / UNLOCK SWITCH -
INSTALLATION, DOOR.................8N-5
LOCK / UNLOCK SWITCH - REMOVAL,
DOOR..............................8N-4
LOCK CYLINDER - INSTALLATION......23-125,
23-138
LOCK CYLINDER - INSTALLATION.......19-11
LOCK CYLINDER - REMOVAL....23-125,23-137
LOCK CYLINDER - REMOVAL...........19-10
LOCK MOTOR - DESCRIPTION, DOOR.....8N-5
LOCK MOTOR - DIAGNOSIS AND
TESTING, DOOR......................8N-5
LOCK MOTOR - OPERATION, DOOR.......8N-5
LOCK OUT - ADJUSTMENT..............5-30
LOCK RELAY - DESCRIPTION, DOOR......8N-6
LOCK RELAY - DIAGNOSIS AND
TESTING, DOOR......................8N-6
LOCK RELAY - INSTALLATION, DOOR.....8N-7
LOCK RELAY - OPERATION, DOOR........8N-6
LOCK RELAY - REMOVAL, DOOR.........8N-6
LOCK SWITCH - DESCRIPTION, DOOR
CYLINDER...........................8Q-9
LOCK SWITCH - DESCRIPTION,
TAILGATE CYLINDER...................8N-9
LOCK SWITCH - DIAGNOSIS AND
TESTING, DOOR CYLINDER............8Q-10
LOCK SWITCH - DIAGNOSIS AND
TESTING, TAILGATE CYLINDER..........8N-9
LOCK SWITCH - INSTALLATION, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - INSTALLATION,
TAILGATE CYLINDER..................8N-10
LOCK SWITCH - OPERATION, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - OPERATION, TAILGATE
CYLINDER...........................8N-9
LOCK SWITCH - REMOVAL, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - REMOVAL, TAILGATE
CYLINDER..........................8N-10
LOCKS - DESCRIPTION, POWER.........8N-1
LOCKS - DIAGNOSIS AND TESTING,
POWER.............................8N-3
LOCKS - OPERATION, POWER...........8N-3
LOCK/UNLOCK SWITCH - DIAGNOSIS
AND TESTING, DOOR..................8N-4
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING......................8O-38
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING......................8O-37
LOW BEAM RELAY - DESCRIPTION,
HEADLAMP.........................8L-39
LOW BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-40
LOW BEAM RELAY - INSTALLATION,
HEADLAMP.........................8L-41
LOW BEAM RELAY - OPERATION,
HEADLAMP.........................8L-39
LOW BEAM RELAY - REMOVAL,
HEADLAMP
.........................8L-40
LOW FUEL INDICATOR - DESCRIPTION
. . . 8J-22
LOW FUEL INDICATOR - OPERATION
.....8J-22
LOW INDICATOR - DESCRIPTION,
COOLANT
...........................8J-15
LOW INDICATOR - OPERATION,
COOLANT
...........................8J-16
LOW LIMITS - DESCRIPTION, HIGH
......25-20
LOW MODE INDICATOR - DESCRIPTION,
FOUR
..............................8J-29
LOW MODE INDICATOR - OPERATION,
FOUR
..............................8J-30
LOW OIL PRESSURE INDICATOR -
DESCRIPTION
.......................8J-23
LOW OIL PRESSURE INDICATOR -
OPERATION
.........................8J-23
LOW PRESSURE SWITCH -
DESCRIPTION, A/C
...................24-18
LOW PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C
...................24-19
LOW PRESSURE SWITCH -
INSTALLATION, A/C
...................24-19
KJINDEX 15
Description Group-Page Description Group-Page Description Group-Page
Page 1757 of 1803
OPERATION - DESCRIPTION, MODES OF . . 8E-11
OPERATION - DIAGNOSIS AND TESTING,
AIR CHECKING TRANSMISSION
CLUTCH............................21-80
ORDER, 2.4L 4-CYLINDER - ENGINE
FIRING..............................8I-2
ORDER, 3.7L V-6 - ENGINE FIRING........8I-2
ORIFICE TUBE - DESCRIPTION, A/C......24-50
ORIFICE TUBE - INSTALLATION, A/C......24-50
ORIFICE TUBE - OPERATION, A/C........24-50
ORIFICE TUBE - REMOVAL, A/C.........24-50
ORVR - DESCRIPTION.................25-29
ORVR - OPERATION..................25-29
OUT - ADJUSTMENT, LOCK..............5-30
OUTBOARD SEAT BELT & RETRACTOR -
INSTALLATION, REAR.................8O-34
OUTBOARD SEAT BELT & RETRACTOR -
REMOVAL, REAR....................8O-33
OUTER BELT MOLDING - INSTALLATION,
FRONT DOOR......................23-186
OUTER BELT MOLDING - INSTALLATION,
REAR DOOR.......................23-186
OUTER BELT MOLDING - REMOVAL,
FRONT DOOR......................23-186
OUTER BELT MOLDING - REMOVAL,
REAR DOOR.......................23-186
OUTER TIE ROD END REMOVAL TOOL,
SPECIAL TOOLS.....................19-15
OUTLET - DESCRIPTION, CIGAR
LIGHTER.........................8W-97-2
OUTLET - DESCRIPTION, POWER......8W-97-11
OUTLET - DIAGNOSIS AND TESTING,
CIGAR LIGHTER...................8W-97-2
OUTLET - DIAGNOSIS AND TESTING,
POWER.........................8W-97-11
OUTLET - INSTALLATION, POWER....8W-97-13
OUTLET - OPERATION, CIGAR LIGHTER . 8W-97-2
OUTLET - OPERATION, POWER......8W-97-11
OUTLET - REMOVAL, POWER........8W-97-12
OUTLET BARRELS - INSTALLATION,
PANEL.............................24-29
OUTLET BARRELS - REMOVAL, PANEL . . . 24-29
OUTLETS - DESCRIPTION, DEMISTER....24-29
OUTPUT - DESCRIPTION, PCM...........8I-4
OUTPUT - OPERATION, PCM............14-33
OUTPUT - OPERATION, PCM.............8I-4
OUTPUT SHAFT SEAL - INSTALLATION,
FRONT......................21-208,21-246
OUTPUT SHAFT SEAL - INSTALLATION,
REAR.............................21-212
OUTPUT SHAFT SEAL - REMOVAL,
FRONT......................21-208,21-246
OUTPUT SHAFT SEAL - REMOVAL, REAR . 21-210
OUTPUT SPEED SENSOR - DESCRIPTION . 21-152
OUTPUT SPEED SENSOR -
INSTALLATION......................21-152
OUTPUT SPEED SENSOR - OPERATION . . 21-152
OUTPUT SPEED SENSOR - REMOVAL . . . 21-152
OVERDRIVE OFF INDICATOR -
DESCRIPTION.......................8J-26
OVERDRIVE OFF INDICATOR -
OPERATION.........................8J-26
OVERDRIVE SWITCH - DESCRIPTION....21-153
OVERDRIVE SWITCH - OPERATION.....21-153
OVERHEAD CONSOLE - DESCRIPTION....8M-1
OVERHEAD CONSOLE - OPERATION......8M-2
OVERHEAD CONSOLE, REMOVAL........8M-4
OVERRIDE RELAY - DESCRIPTION,
CLUTCH SWITCH......................6-10
OVERRIDE RELAY - INSTALLATION,
CLUTCH SWITCH......................6-10
OVERRIDE RELAY - OPERATION,
CLUTCH SWITCH......................6-10
OVERRIDE RELAY - REMOVAL, CLUTCH
SWITCH.............................6-10
OXYGEN SENSOR - DESCRIPTION.......14-40
OXYGEN SENSOR - INSTALLATION.......14-43
OXYGEN SENSOR - OPERATION.........14-40
OXYGEN SENSOR - REMOVAL..........14-41
PADS - INSTALLATION, FRONT BRAKE.....5-11
PADS - REMOVAL, FRONT BRAKE........5-11
PAINT CODE - DESCRIPTION..........23-162
PAINT CODES - SPECIFICATIONS.......23-162
PAINT TOUCH-UP - DESCRIPTION
......23-163
PAN - CLEANING, OIL
..................9-63
PAN - DESCRIPTION, OIL
...............9-63
PAN - INSPECTION, OIL
................9-63
PAN - INSTALLATION, OIL
...............9-64PAN - REMOVAL, OIL..................9-63
PANEL - DESCRIPTION, LATCH - ACCESS . 23-139
PANEL - INSTALLATION, GLASS........23-178
PANEL - INSTALLATION, LATCH -
ACCESS...........................23-139
PANEL - INSTALLATION, QUARTER TRIM . 23-159
PANEL - INSTALLATION, TRIM . . . 23-126,23-132,
23-138
PANEL - REMOVAL, GLASS............23-178
PANEL - REMOVAL, LATCH - ACCESS . . . 23-139
PANEL - REMOVAL, QUARTER TRIM....23-159
PANEL - REMOVAL, TRIM . 23-125,23-132,23-138
PANEL ADJUSTMENT, ADJUSTMENTS -
SUNROOF GLASS...................23-178
PANEL ANTENNA CABLE -
INSTALLATION, INSTRUMENT............8A-8
PANEL ANTENNA CABLE - REMOVAL,
INSTRUMENT........................8A-7
PANEL ASSEMBLY - INSTALLATION,
INSTRUMENT......................23-151
PANEL ASSEMBLY - REMOVAL,
INSTRUMENT......................23-149
PANEL CENTER BEZEL - INSTALLATION,
INSTRUMENT......................23-154
PANEL CENTER BEZEL - REMOVAL,
INSTRUMENT......................23-154
PANEL DOOR - INSTALLATION..........24-36
PANEL DOOR ACTUATOR -
INSTALLATION.......................24-25
PANEL DOOR ACTUATOR - REMOVAL....24-24
PANEL DRIVER SIDE BEZELS -
INSTALLATION, INSTRUMENT..........23-154
PANEL DRIVER SIDE BEZELS -
REMOVAL, INSTRUMENT.............23-153
PANEL END CAP - INSTALLATION,
INSTRUMENT......................23-153
PANEL END CAP - REMOVAL,
INSTRUMENT......................23-153
PANEL OUTLET BARRELS -
INSTALLATION.......................24-29
PANEL OUTLET BARRELS - REMOVAL....24-29
PANEL PASSENGER SIDE BEZEL -
INSTALLATION, INSTRUMENT..........23-154
PANEL PASSENGER SIDE BEZEL -
REMOVAL, INSTRUMENT.............23-154
PANEL SEAL - INSTALLATION, GLASS . . . 23-178
PANEL SEAL - REMOVAL, GLASS.......23-178
PANEL TOP COVER - INSTALLATION,
INSTRUMENT......................23-153
PANEL TOP COVER - REMOVAL,
INSTRUMENT......................23-152
PARK - INTERLOCK CABLE -
INSTALLATION......................21-153
PARK - INTERLOCK CABLE - REMOVAL . . 21-153
PARK LAMP RELAY - DESCRIPTION......8L-54
PARK LAMP RELAY - DIAGNOSIS AND
TESTING...........................8L-55
PARK LAMP RELAY - INSTALLATION.....8L-56
PARK LAMP RELAY - OPERATION.......8L-54
PARK LAMP RELAY - REMOVAL.........8L-55
PARK RAMP - INSTALLATION, WIPER
ARM ..............................8R-43
PARK RAMP - REMOVAL, WIPER ARM . . . 8R-43
PARKING BRAKE - DESCRIPTION.........5-29
PARKING BRAKE - OPERATION...........5-29
PARK-INTERLOCK CABLE -
ADJUSTMENTS.....................21-154
PART TIME INDICATOR - DESCRIPTION . . . 8J-29
PART TIME INDICATOR - OPERATION.....8J-29
PASSENGER AIRBAG - DESCRIPTION....8O-27
PASSENGER AIRBAG - INSTALLATION....8O-29
PASSENGER AIRBAG - OPERATION......8O-27
PASSENGER AIRBAG - REMOVAL........8O-28
PASSENGER AIRBAG DOOR -
INSTALLATION......................8O-30
PASSENGER AIRBAG DOOR - REMOVAL . . 8O-29
PASSENGER AIRBAG MOUNTING
BRACKET - INSTALLATION.............8O-31
PASSENGER AIRBAG MOUNTING
BRACKET - REMOVAL
.................8O-31
PASSENGER SEAT HEATER SWITCH -
DESCRIPTION
.......................8G-14
PASSENGER SEAT HEATER SWITCH -
INSTALLATION
......................8G-15
PASSENGER SEAT HEATER SWITCH -
OPERATION
.........................8G-14
PASSENGER SEAT HEATER SWITCH -
REMOVAL
..........................8G-15PASSENGER SIDE BEZEL -
INSTALLATION, INSTRUMENT PANEL....23-154
PASSENGER SIDE BEZEL - REMOVAL,
INSTRUMENT PANEL.................23-154
PATTERNS - DIAGNOSIS AND TESTING,
TIRE WEAR..........................22-8
PCM - DESCRIPTION..................8E-11
PCM - OPERATION...................8E-14
PCM INPUT - OPERATION, ASD SENSE.....8I-4
PCM OUTPUT - DESCRIPTION............8I-4
PCM OUTPUT - OPERATION............14-33
PCM OUTPUT - OPERATION.............8I-4
PCM/SKIM PROGRAMMING - STANDARD
PROCEDURE.........................8E-1
PCV VALVE - DESCRIPTION............25-29
PCV VALVE - DIAGNOSIS AND TESTING . . . 25-31
PCV VALVE - INSTALLATION............25-32
PCV VALVE - OPERATION..............25-31
PCV VALVE - REMOVAL...............25-32
PEDAL - DESCRIPTION.................5-20
PEDAL - INSTALLATION................5-20
PEDAL - INSTALLATION, ACCELERATOR . . . 14-30
PEDAL - INSTALLATION, CLUTCH.........6-10
PEDAL - OPERATION...................5-20
PEDAL - REMOVAL....................5-20
PEDAL - REMOVAL, ACCELERATOR......14-29
PEDAL - REMOVAL, CLUTCH............6-10
PEDAL POSITION SWITCH -
DESCRIPTION, CLUTCH.................6-11
PEDAL POSITION SWITCH - DIAGNOSIS
AND TESTING, CLUTCH.................6-11
PEDAL POSITION SWITCH - OPERATION,
CLUTCH.............................6-11
PERFORMANCE - DIAGNOSIS AND
TESTING, A/C........................24-2
PERFORMANCE - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS............9-4
PERFORMANCE - DIAGNOSIS AND
TESTING, HEATER.....................24-6
PILOT BEARING - INSTALLATION..........6-8
PILOT BEARING - REMOVAL..............6-8
PINION GEAR/RING GEAR -
INSTALLATION........................3-46
PINION GEAR/RING GEAR - REMOVAL.....3-44
PINION GEAR/RING GEAR/TONE RING -
INSTALLATION...................3-112,3-82
PINION GEAR/RING GEAR/TONE RING -
REMOVAL......................3-110,3-79
PINION SEAL - INSTALLATION . . 3-103,3-39,3-68
PINION SEAL - REMOVAL......3-102,3-38,3-68
PIPE - INSTALLATION, CROSS-OVER......11-3
PIPE - REMOVAL, CROSS-OVER..........11-3
PISTON & CONNECTING ROD -
DESCRIPTION........................9-49
PISTON FITTING - STANDARD
PROCEDURE.........................9-50
PISTON RING FITTING - STANDARD
PROCEDURE.........................9-52
PISTONS - DESCRIPTION.............21-155
PISTONS - OPERATION...............21-155
PLANETARY GEARTRAIN - ASSEMBLY . . . 21-160
PLANETARY GEARTRAIN - CLEANING....21-159
PLANETARY GEARTRAIN - DESCRIPTION . 21-157
PLANETARY GEARTRAIN -
DISASSEMBLY......................21-159
PLANETARY GEARTRAIN - INSPECTION . . 21-159
PLANETARY GEARTRAIN - OPERATION . . 21-157
PLATE - INSTALLATION, DOOR SILL
SCUFF............................23-157
PLATE - INSTALLATION, FLEX............9-49
PLATE - INSTALLATION, FRONT SKID......13-6
PLATE - INSTALLATION, FUEL TANK
SKID...............................13-9
PLATE - INSTALLATION, REAR DOOR
SCUFF............................23-160
PLATE - INSTALLATION, TRANSFER
CASE SKID..........................13-7
PLATE - REMOVAL, DOOR SILL SCUFF . . . 23-157
PLATE - REMOVAL, FLEX...............9-49
PLATE - REMOVAL, FRONT SKID.........13-6
PLATE - REMOVAL, FUEL TANK SKID
......13-9
PLATE - REMOVAL, REAR DOOR SCUFF
. . 23-160
PLATE - REMOVAL, TRANSFER CASE
SKID
...............................13-7
PLATE LAMP BULB - INSTALLATION,
LICENSE
...........................8L-45
PLATE LAMP BULB - REMOVAL,
LICENSE
...........................8L-44
18 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page
Page 1764 of 1803
SPARK PLUG - OPERATION.............8I-12
SPARK PLUG - REMOVAL..............8I-15
SPARK PLUG CABLE RESISTANCE, 2.4L....8I-3
SPARK PLUG CONDITIONS - DIAGNOSIS
AND TESTING........................8I-13
SPARK PLUGS, SPARK PLUG -
CLEANING..........................8I-15
SPARK PLUGS, SPECIFICATIONS..........8I-3
SPEAKER - DESCRIPTION..............8A-13
SPEAKER - INSTALLATION.............8A-15
SPEAKER - OPERATION...............8A-14
SPEAKER - REMOVAL.................8A-14
SPECIAL TOOLS - 3.7L ENGINE..........9-15
SPECIAL TOOLS - 8 1/4 AXLE...........3-98
SPECIAL TOOLS - BASE BRAKES..........5-7
SPECIAL TOOLS - BODY................23-5
SPECIAL TOOLS - COOLING.............7-14
SPECIAL TOOLS - FRONT AXLE..........3-34
SPECIAL TOOLS - FRONT SUSPENSION.....2-8
SPECIAL TOOLS - FUEL SYSTEM.........14-6
SPECIAL TOOLS - OUTER TIE ROD END
REMOVAL TOOL.....................19-15
SPECIAL TOOLS - POWER
DISTRIBUTION SYSTEMS............8W-97-2
SPECIAL TOOLS - POWER STEERING
PUMP.............................19-20
SPECIAL TOOLS - REAR AXLE...........3-63
SPECIAL TOOLS - RFE TRANSMISSION....21-120
SPECIAL TOOLS - STEERING COLUMN....19-8
SPECIAL TOOLS - WIRING/TERMINAL . 8W-01-10
SPECIAL TOOLS, BATTERY SYSTEM.......8F-7
SPECIFICATIONS, BATTERY SYSTEM......8F-6
SPECIFICATIONS, BRAKES - ABS.........5-33
SPECIFICATIONS, CHARGE CAPACITY.....24-42
SPECIFICATIONS, CLUTCH...............6-5
SPECIFICATIONS, DIAGNOSIS AND
TESTING............................22-8
SPECIFICATIONS, FLUID CAPACITIES.......0-4
SPECIFICATIONS, FRAME DIMENSIONS....13-3
SPECIFICATIONS, FRONT AXLE...........3-33
SPECIFICATIONS, GAP AND FLUSH.....23-116
SPECIFICATIONS, IGNITION TIMING.......8I-2
SPECIFICATIONS, LAMPS/LIGHTING -
EXTERIOR..........................8L-15
SPECIFICATIONS, LAMPS/LIGHTING -
INTERIOR..........................8L-71
SPECIFICATIONS, NV1500..............21-30
SPECIFICATIONS, OPENING DIMENSIONS . 23-111
SPECIFICATIONS, PAINT CODES........23-162
SPECIFICATIONS, REAR AXLE............3-62
SPECIFICATIONS, REMOTE KEYLESS
ENTRY TRANSMITTER.................8N-9
SPECIFICATIONS, SEALER LOCATIONS....23-87
SPECIFICATIONS, SPECIFICATIONS.......24-10
SPECIFICATIONS, STANDARD
PROCEDURE.........................23-4
SPECIFICATIONS, TORQUE..............13-6
SPECIFICATIONS, WELD AND
STRUCTURAL ADHESIVE LOCATIONS......23-9
SPEED CONTROL - DESCRIPTION........8P-1
SPEED CONTROL - OPERATION..........8P-1
SPEED CONTROL - TORQUE.............8P-2
SPEED SENSOR - DESCRIPTION, INPUT . 21-143
SPEED SENSOR - DESCRIPTION,
OUTPUT...........................21-152
SPEED SENSOR - INSTALLATION, FRONT
WHEEL.............................5-34
SPEED SENSOR - INSTALLATION, INPUT . 21-143
SPEED SENSOR - INSTALLATION,
OUTPUT...........................21-152
SPEED SENSOR - INSTALLATION, REAR
WHEEL.............................5-35
SPEED SENSOR - OPERATION, INPUT . . . 21-143
SPEED SENSOR - OPERATION, OUTPUT . . 21-152
SPEED SENSOR - REMOVAL, FRONT
WHEEL.............................5-34
SPEED SENSOR - REMOVAL, INPUT.....21-143
SPEED SENSOR - REMOVAL, OUTPUT . . . 21-152
SPEED SENSOR - REMOVAL, REAR
WHEEL.............................5-35
SPEEDOMETER - DESCRIPTION
.........8J-32
SPEEDOMETER - OPERATION
...........8J-32
SPLASH SHIELD - INSTALLATION,
FRONT WHEELHOUSE
................23-143
SPLASH SHIELD - INSTALLATION, REAR
WHEELHOUSE
......................23-144
SPLASH SHIELD - REMOVAL, FRONT
WHEELHOUSE
......................23-143SPLASH SHIELD - REMOVAL, REAR
WHEELHOUSE......................23-144
SPLICE INFORMATION - DESCRIPTION,
CONNECTOR, GROUND..............8W-01-7
SPLICING - STANDARD PROCEDURE,
WIRE...........................8W-01-14
SPRING - INSTALLATION...........2-13,2-18
SPRING - REMOVAL...............2-13,2-18
SPRINGS - DESCRIPTION, VALVE.....9-29,9-38
SPRINGS - INSTALLATION, VALVE....9-29,9-38
SPRINGS - REMOVAL, VALVE........9-29,9-38
STABILIZER BAR - INSTALLATION....2-14,2-19
STABILIZER BAR - REMOVAL........2-14,2-19
STABILIZER BAR BUSHINGS -
INSTALLATION.........................2-9
STABILIZER BAR BUSHINGS - REMOVAL....2-9
STABILIZER LINK - INSTALLATION........2-14
STABILIZER LINK - REMOVAL............2-14
STAKING - STANDARD PROCEDURE,
HEAT ...............................23-3
STARTER MOTOR - DIAGNOSIS AND
TESTING...........................8F-39
STARTER MOTOR - INSTALLATION.......8F-41
STARTER MOTOR - REMOVAL..........8F-39
STARTER MOTOR, GAS POWERED.......8F-39
STARTER MOTOR RELAY - DESCRIPTION . 8F-41
STARTER MOTOR RELAY -
INSTALLATION.......................8F-43
STARTER MOTOR RELAY - OPERATION.....8F-42
STARTER MOTOR RELAY - REMOVAL.....8F-43
STARTER RELAY - DIAGNOSIS AND
TESTING...........................8F-42
STARTING PROCEDURE - STANDARD
PROCEDURE, JUMP....................0-5
STARTING SYSTEM - DESCRIPTION......8F-32
STARTING SYSTEM - DIAGNOSIS AND
TESTING...........................8F-33
STARTING SYSTEM - INSPECTION.......8F-37
STARTING SYSTEM - OPERATION........8F-32
STATE DISPLAY TEST MODE -
DESCRIPTION........................25-2
STEERING - DESCRIPTION..............19-1
STEERING - OPERATION................19-1
STEERING COLUMN, SPECIAL TOOLS.....19-8
STEERING FLOW AND PRESSURE -
DIAGNOSIS AND TESTING, POWER.......19-3
STEERING LINKAGE - STANDARD
PROCEDURE........................19-16
STEERING PRESSURE SWITCH -
DESCRIPTION, POWER................19-22
STEERING PRESSURE SWITCH -
INSTALLATION, POWER...............19-22
STEERING PRESSURE SWITCH -
OPERATION, POWER..................19-22
STEERING PRESSURE SWITCH -
REMOVAL, POWER...................19-22
STEERING PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER.......19-18
STEERING PUMP, SPECIAL TOOLS -
POWER............................19-20
STEERING SYSTEM - DIAGNOSIS AND
TESTING, POWER.....................19-1
STEERING SYSTEM - DIAGNOSIS AND
TESTING, SUSPENSION.................2-1
STEERING WHEEL - INSTALLATION......19-12
STEERING WHEEL - REMOVAL..........19-12
STOP LAMP BULB - INSTALLATION,
CENTER HIGH MOUNTED..............8L-19
STOP LAMP BULB - REMOVAL, CENTER
HIGH MOUNTED.....................8L-18
STOP LAMP UNIT - INSTALLATION,
CENTER HIGH MOUNTED..............8L-19
STOP LAMP UNIT - REMOVAL, CENTER
HIGH MOUNTED.....................8L-19
STRAP - DESCRIPTION, RADIO NOISE
SUPPRESSION GROUND................8A-9
STRAP - INSTALLATION, CHECK . 23-121,23-128,
23-135
STRAP - INSTALLATION, RADIO NOISE
SUPPRESSION GROUND
...............8A-11
STRAP - OPERATION, RADIO NOISE
SUPPRESSION GROUND
...............8A-10
STRAP - REMOVAL, CHECK
.....23-121,23-128,
23-135
STRAP - REMOVAL, RADIO NOISE
SUPPRESSION GROUND
...............8A-10
STRIKER - INSTALLATION, GLOVE BOX
LATCH
............................23-149STRIKER - INSTALLATION, HOOD AJAR
SWITCH............................8Q-14
STRIKER - INSTALLATION, LATCH......23-124,
23-132,23-137
STRIKER - INSTALLATION, REAR SEAT
BACK LATCH.......................23-171
STRIKER - REMOVAL, GLOVE BOX
LATCH ............................23-148
STRIKER - REMOVAL, HOOD AJAR
SWITCH............................8Q-13
STRIKER - REMOVAL, LATCH . . . 23-124,23-132,
23-137
STRIKER - REMOVAL, REAR SEAT BACK
LATCH ............................23-170
STRUCTURAL ADHESIVE LOCATIONS -
SPECIFICATIONS, WELD................23-9
STRUCTURAL COVER - DESCRIPTION.....9-55
STRUCTURAL COVER - INSTALLATION.....9-55
STRUCTURAL COVER - OPERATION.......9-55
STRUCTURAL COVER - REMOVAL........9-55
STUDS - INSTALLATION...............22-11
STUDS - REMOVAL...................22-11
SUCTION LINE - INSTALLATION, A/C.....24-49
SUCTION LINE - REMOVAL, A/C.........24-48
SUN VISOR - INSTALLATION..........23-160
SUN VISOR - REMOVAL..............23-160
SUN VISOR SUPPORT - INSTALLATION . . 23-160
SUN VISOR SUPPORT - REMOVAL......23-160
SUNROOF - DESCRIPTION............23-175
SUNROOF GLASS PANEL ADJUSTMENT,
ADJUSTMENTS.....................23-178
SUNSHADE - INSTALLATION...........23-179
SUNSHADE - REMOVAL..............23-179
SUPPLEMENTAL RESTRAINT
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A.........8O-6
SUPPLEMENTAL RESTRAINT SYSTEM -
DIAGNOSIS AND TESTING..............8O-6
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE, HANDLING
NON-DEPLOYED......................8O-6
SUPPLIES - DESCRIPTION, 5 VOLT......8E-13
SUPPLIES - OPERATION, 5 VOLT........8E-15
SUPPORT - INSTALLATION, REAR
FASCIA..............................13-3
SUPPORT - INSTALLATION, SUN VISOR . . 23-160
SUPPORT - REMOVAL, REAR FASCIA......13-3
SUPPORT - REMOVAL, SUN VISOR.....23-160
SUPPORT BRACKET - INSTALLATION,
REARVIEW MIRROR.................23-161
SUPPORT CYLINDER - INSTALLATION . . . 23-120
SUPPORT CYLINDER - INSTALLATION,
FLIP-UP GLASS.....................23-139
SUPPORT CYLINDER - REMOVAL.......23-120
SUPPORT CYLINDER - REMOVAL,
FLIP-UP GLASS.....................23-139
SUPPRESSION GROUND STRAP -
DESCRIPTION, RADIO NOISE............8A-9
SUPPRESSION GROUND STRAP -
INSTALLATION, RADIO NOISE...........8A-11
SUPPRESSION GROUND STRAP -
OPERATION, RADIO NOISE.............8A-10
SUPPRESSION GROUND STRAP -
REMOVAL, RADIO NOISE..............8A-10
SURFACE PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET............9-9
SUSPENSION - DIAGNOSIS AND
TESTING, REAR.......................2-17
SUSPENSION AND STEERING SYSTEM -
DIAGNOSIS AND TESTING...............2-1
SUSPENSION ARM, BUSHINGS, AND
BALL JOINT - DESCRIPTION, UPPER......2-20
SUSPENSION ARM, BUSHINGS, AND
BALL JOINT - OPERATION, UPPER........2-20
SUSPENSION, SPECIAL TOOLS - FRONT....2-8
SWING GATE - INSTALLATION.........23-138
SWING GATE - REMOVAL.............23-138
SWING GATE BELTLINE WEATHERSTRIP
- INSTALLATION....................23-186
SWING GATE BELTLINE WEATHERSTRIP
- REMOVAL
........................23-186
SWING GATE OPENING WEATHERSTRIP
- INSTALLATION
....................23-186
SWING GATE OPENING WEATHERSTRIP
- REMOVAL
........................23-186
SWITCH - DESCRIPTION
................8P-5
SWITCH - DESCRIPTION, A/C HIGH
PRESSURE
.........................24-17
KJINDEX 25
Description Group-Page Description Group-Page Description Group-Page
Page 1771 of 1803
COOLANT TEMPERATURE SENSOR -
OPERATION, ENGINE...................7-21
COOLANT TEMPERATURE SENSOR -
REMOVAL, ENGINE....................7-21
COOLER - DESCRIPTION, TRANS.........7-30
COOLERS AND TUBES - STANDARD
PROCEDURE, FLUSHING................7-30
COOLING, SPECIAL TOOLS..............7-13
COOLING SYSTEM - OPERATION..........7-2
COOLING SYSTEM - REVERSE
FLUSHING - STANDARD PROCEDURE.....7-12
COOLING SYSTEM - STANDARD
PROCEDURE, DRAINING................7-11
COOLING SYSTEM - STANDARD
PROCEDURE, REFILLING................7-11
COOLING SYSTEM 2.4L ENGINE -
DESCRIPTION.........................7-1
COOLING SYSTEM DIAGNOSIS CHART -
DIAGNOSIS AND TESTING...............7-5
COOLING SYSTEM LEAKS - DIAGNOSIS
AND TESTING.........................7-2
CORE AND OIL GALLERY PLUGS -
STANDARD PROCEDURE, ENGINE.........9-9
COVER - CLEANING, CYLINDER HEAD.....9-26
COVER - INSPECTION, CYLINDER HEAD . . . 9-26
COVER - INSTALLATION, CYLINDER
HEAD...............................9-26
COVER - REMOVAL, CYLINDER HEAD.....9-26
COVER(S) - INSTALLATION, TIMING
BELT ...............................9-53
COVER(S) - REMOVAL, TIMING BELT......9-53
CRANKSHAFT - DESCRIPTION...........9-32
CRANKSHAFT - INSPECTION.............9-34
CRANKSHAFT - INSTALLATION...........9-34
CRANKSHAFT - OPERATION.............9-33
CRANKSHAFT - REMOVAL..............9-33
CRANKSHAFT END PLAY - STANDARD
PROCEDURE.........................9-33
CRANKSHAFT OIL SEAL - FRONT -
INSTALLATION........................9-37
CRANKSHAFT OIL SEAL - FRONT -
REMOVAL...........................9-37
CRANKSHAFT OIL SEAL - REAR -
INSTALLATION........................9-39
CRANKSHAFT OIL SEAL - REAR -
REMOVAL...........................9-38
CRANKSHAFT SPROCKET -
INSTALLATION........................9-56
CRANKSHAFT SPROCKET - REMOVAL.....9-55
CROSS-OVER PIPE - INSTALLATION.......11-4
CROSS-OVER PIPE - REMOVAL..........11-4
CYLINDER BORE FITTING - STANDARD
PROCEDURE, PISTON TO...............9-30
CYLINDER BORE HONING - STANDARD
PROCEDURE.........................9-31
CYLINDER COMBUSTION PRESSURE
LEAKAGE TEST - DIAGNOSIS AND
TESTING.............................9-3
CYLINDER COMPRESSION PRESSURE
TEST - DIAGNOSIS AND TESTING.........9-3
CYLINDER HEAD - CLEANING............9-20
CYLINDER HEAD - DESCRIPTION.........9-19
CYLINDER HEAD - INSPECTION..........9-21
CYLINDER HEAD - INSTALLATION........9-21
CYLINDER HEAD - OPERATION...........9-19
CYLINDER HEAD - REMOVAL............9-20
CYLINDER HEAD COVER - CLEANING......9-26
CYLINDER HEAD COVER - INSPECTION....9-26
CYLINDER HEAD COVER -
INSTALLATION
........................9-26
CYLINDER HEAD COVER - REMOVAL
......9-26
CYLINDER HEAD GASKET - DIAGNOSIS
AND TESTING
........................9-19
CYLINDER HEAD OFF - INSTALLATION
.....9-28
CYLINDER HEAD OFF - REMOVAL
........9-27
CYLINDER HEAD ON - INSTALLATION
.....9-28
CYLINDER HEAD ON - REMOVAL
.........9-27
DAMAGED OR WORN THREADS -
STANDARD PROCEDURE, REPAIR OF
.......9-9
DAMPER - INSTALLATION, VIBRATION
.....9-43
DAMPER - REMOVAL, VIBRATION
........9-43
DAYTIME RUNNING LAMP RELAY -
DESCRIPTION
.......................8L-20
DAYTIME RUNNING LAMP RELAY -
INSTALLATION
.......................8L-21
DAYTIME RUNNING LAMP RELAY -
OPERATION
.........................8L-20DAYTIME RUNNING LAMP RELAY -
REMOVAL..........................8L-21
DESCRIPTION - OPERATION.............7-20
DESCRIPTION, BACKUP LAMP SWITCH . . . 8L-15
DESCRIPTION, BALANCE SHAFT..........9-59
DESCRIPTION, BRAKE LAMP SWITCH....8L-16
DESCRIPTION, CAMSHAFT(S)............9-23
DESCRIPTION, CATALYTIC CONVERTER....11-2
DESCRIPTION, COMBINATION FLASHER . . . 8L-19
DESCRIPTION, COOLANT RECOVERY
PRESS CONTAINER....................7-20
DESCRIPTION, COOLING SYSTEM 2.4L
ENGINE..............................7-1
DESCRIPTION, CRANKSHAFT............9-32
DESCRIPTION, CYLINDER HEAD..........9-19
DESCRIPTION, DAYTIME RUNNING
LAMP RELAY........................8L-20
DESCRIPTION, ENGINE - 2.4L.............9-3
DESCRIPTION, ENGINE BLOCK...........9-30
DESCRIPTION, ENGINE BLOCK HEATER -
2.4L................................7-20
DESCRIPTION, ENGINE COOLANT.........7-19
DESCRIPTION, ENGINE COOLANT
TEMPERATURE SENSOR................7-21
DESCRIPTION, ENGINE MOUNTING.......9-44
DESCRIPTION, EXHAUST MANIFOLD......9-53
DESCRIPTION, EXHAUST SYSTEM........11-1
DESCRIPTION, FRONT FOG LAMP RELAY . . 8L-22
DESCRIPTION, HAZARD SWITCH........8L-28
DESCRIPTION, HEADLAMP HIGH BEAM
RELAY.............................8L-33
DESCRIPTION, HEADLAMP LEVELING
MOTOR............................8L-35
DESCRIPTION, HEADLAMP LEVELING
SWITCH............................8L-37
DESCRIPTION, HEADLAMP LOW BEAM
RELAY.............................8L-39
DESCRIPTION, HEAT SHIELDS...........11-4
DESCRIPTION, HOAT COOLANT..........7-18
DESCRIPTION, HOSE CLAMPS............7-1
DESCRIPTION, INTAKE MANIFOLD........9-51
DESCRIPTION, INTAKE/EXHAUST VALVES
& SEATS ............................9-27
DESCRIPTION, LAMP BAR.............8L-65
DESCRIPTION, LAMP BAR SWITCH......8L-67
DESCRIPTION, LAMPS/LIGHTING -
EXTERIOR...........................8L-2
DESCRIPTION, LUBRICATION............9-46
DESCRIPTION, MUFFLER...............11-4
DESCRIPTION, MULTI-FUNCTION
SWITCH............................8L-46
DESCRIPTION, OIL FILTER..............9-47
DESCRIPTION, OIL PRESSURE
SENSOR/SWITCH.....................9-48
DESCRIPTION, PARK LAMP RELAY.......8L-54
DESCRIPTION, PISTON & CONNECTING
ROD................................9-40
DESCRIPTION, RADIATOR...............7-22
DESCRIPTION, RADIATOR FAN -
ELECTRIC...........................7-26
DESCRIPTION, RADIATOR PRESSURE
CAP ................................7-25
DESCRIPTION, REAR FOG LAMP RELAY . . . 8L-56
DESCRIPTION, TRAILER TOW RELAY.....8L-62
DESCRIPTION, TRAILER TOW WIRING....8L-64
DESCRIPTION, TRANS COOLER..........7-30
DESCRIPTION, WATER PUMP - 2.4L......7-27
DIAGNOSIS - DIAGNOSIS AND TESTING,
LASH ADJUSTER (TAPPET) NOISE........9-28
DIAGNOSIS - DIAGNOSIS AND TESTING,
SERPENTINE DRIVE BELT...............7-15
DIAGNOSIS - PERFORMANCE -
DIAGNOSIS AND TESTING, ENGINE........9-5
DIAGNOSIS AND TESTING, BACKUP
LAMP SWITCH......................8L-15
DIAGNOSIS AND TESTING, BRAKE LAMP
SWITCH............................8L-17
DIAGNOSIS AND TESTING, COOLING
SYSTEM DIAGNOSIS CHART
..............7-5
DIAGNOSIS AND TESTING, COOLING
SYSTEM LEAKS
........................7-2
DIAGNOSIS AND TESTING, CYLINDER
COMBUSTION PRESSURE LEAKAGE
TEST
................................9-3
DIAGNOSIS AND TESTING, CYLINDER
COMPRESSION PRESSURE TEST
..........9-3
DIAGNOSIS AND TESTING, CYLINDER
HEAD GASKET
........................9-19DIAGNOSIS AND TESTING, ENGINE........9-5
DIAGNOSIS AND TESTING, ENGINE
DIAGNOSIS - PERFORMANCE.............9-5
DIAGNOSIS AND TESTING, ENGINE
MECHANICAL.........................9-7
DIAGNOSIS AND TESTING, ENGINE OIL
LEAK INSPECTION......................9-4
DIAGNOSIS AND TESTING, ENGINE OIL
PRESSURE CHECKING.................9-46
DIAGNOSIS AND TESTING, EXHAUST
SYSTEM............................11-2
DIAGNOSIS AND TESTING, FRONT FOG
LAMP RELAY........................8L-23
DIAGNOSIS AND TESTING, HEADLAMP
HIGH BEAM RELAY...................8L-34
DIAGNOSIS AND TESTING, HEADLAMP
LEVELING SWITCH...................8L-37
DIAGNOSIS AND TESTING, HEADLAMP
LOW BEAM RELAY...................8L-40
DIAGNOSIS AND TESTING, INTAKE
MANIFOLD LEAKS.....................9-51
DIAGNOSIS AND TESTING, LAMP BAR....8L-65
DIAGNOSIS AND TESTING, LAMPS/
LIGHTING - EXTERIOR.................8L-7
DIAGNOSIS AND TESTING, LASH
ADJUSTER (TAPPET) NOISE
DIAGNOSIS..........................9-28
DIAGNOSIS AND TESTING, MULTI-
FUNCTION SWITCH...................8L-50
DIAGNOSIS AND TESTING, ON-BOARD
DIAGNOSTICS (OBD)....................7-2
DIAGNOSIS AND TESTING, PARK LAMP
RELAY.............................8L-55
DIAGNOSIS AND TESTING,
PRELIMINARY CHECKS..................7-2
DIAGNOSIS AND TESTING, RADIATOR
PRESSURE CAP.......................7-25
DIAGNOSIS AND TESTING, REAR FOG
LAMP RELAY........................8L-57
DIAGNOSIS AND TESTING, SERPENTINE
DRIVE BELT DIAGNOSIS................7-15
DIAGNOSIS AND TESTING, TRAILER
TOW RELAY.........................8L-62
DIAGNOSIS CHART - DIAGNOSIS AND
TESTING, COOLING SYSTEM.............7-5
DIAGNOSTICS (OBD) - DIAGNOSIS AND
TESTING, ON-BOARD...................7-2
DISASSEMBLY, OIL PUMP...............9-49
DRAINING COOLING SYSTEM -
STANDARD PROCEDURE................7-11
DRIVE BELT DIAGNOSIS - DIAGNOSIS
AND TESTING, SERPENTINE.............7-15
ELECTRIC - DESCRIPTION, RADIATOR
FAN ................................7-26
ELECTRIC - INSTALLATION, RADIATOR
FAN ................................7-27
ELECTRIC - OPERATION, RADIATOR FAN . . . 7-26
ELECTRIC - REMOVAL, RADIATOR FAN....7-26
END PLAY - STANDARD PROCEDURE,
CRANKSHAFT........................9-33
END-PLAY - STANDARD PROCEDURE,
CAMSHAFT..........................9-23
ENGINE - 2.4L - DESCRIPTION............9-3
ENGINE - DESCRIPTION, COOLING
SYSTEM 2.4L.........................7-1
ENGINE - DIAGNOSIS AND TESTING.......9-5
ENGINE - INSTALLATION, 2.4L . . 7-14,7-17,7-22,
7-28
ENGINE - REMOVAL, 2.4L . . . 7-14,7-16,7-22,7-27
ENGINE - SPECIFICATIONS, 2.4L.........9-13
ENGINE - STANDARD PROCEDURE,
HYDROSTATIC LOCKED..................9-9
ENGINE ASSEMBLY - INSTALLATION......9-12
ENGINE ASSEMBLY - REMOVAL..........9-12
ENGINE BLOCK - DESCRIPTION..........9-30
ENGINE BLOCK HEATER - 2.4L -
DESCRIPTION........................7-20
ENGINE BLOCK HEATER - 2.4L -
OPERATION..........................7-20
ENGINE COOLANT - DESCRIPTION
........7-19
ENGINE COOLANT TEMPERATURE
SENSOR - DESCRIPTION
...............7-21
ENGINE COOLANT TEMPERATURE
SENSOR - INSTALLATION
...............7-22
ENGINE COOLANT TEMPERATURE
SENSOR - OPERATION
.................7-21
ENGINE COOLANT TEMPERATURE
SENSOR - REMOVAL
...................7-21
2 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page
Page 1772 of 1803
ENGINE CORE AND OIL GALLERY PLUGS
- STANDARD PROCEDURE...............9-9
ENGINE DIAGNOSIS - PERFORMANCE -
DIAGNOSIS AND TESTING...............9-5
ENGINE GASKET SURFACE
PREPARATION - STANDARD
PROCEDURE.........................9-11
ENGINE MECHANICAL - DIAGNOSIS AND
TESTING.............................9-7
ENGINE MOUNTING - DESCRIPTION......9-44
ENGINE OIL AND FILTER CHANGE -
STANDARD PROCEDURE................9-47
ENGINE OIL LEAK INSPECTION -
DIAGNOSIS AND TESTING...............9-4
ENGINE OIL LEVEL CHECK, STANDARD
PROCEDURE.........................9-47
ENGINE OIL PRESSURE CHECKING -
DIAGNOSIS AND TESTING..............9-46
ENGINE, SPECIAL TOOLS - 2.4L..........9-17
EXHAUST MANIFOLD - CLEANING........9-53
EXHAUST MANIFOLD - DESCRIPTION.....9-53
EXHAUST MANIFOLD - INSPECTION.......9-53
EXHAUST MANIFOLD - INSTALLATION.....9-53
EXHAUST MANIFOLD - OPERATION.......9-53
EXHAUST MANIFOLD - REMOVAL.........9-53
EXHAUST SYSTEM - DESCRIPTION.......11-1
EXHAUST SYSTEM - DIAGNOSIS AND
TESTING............................11-2
EXTERIOR - DESCRIPTION, LAMPS/
LIGHTING...........................8L-2
EXTERIOR - DIAGNOSIS AND TESTING,
LAMPS/LIGHTING.....................8L-7
EXTERIOR - OPERATION, LAMPS/
LIGHTING...........................8L-5
EXTERIOR - SPECIFICATIONS,
LAMPS/LIGHTING....................8L-15
FAN - ELECTRIC - DESCRIPTION,
RADIATOR...........................7-26
FAN - ELECTRIC - INSTALLATION,
RADIATOR...........................7-27
FAN - ELECTRIC - OPERATION,
RADIATOR...........................7-26
FAN - ELECTRIC - REMOVAL, RADIATOR . . . 7-26
FILTER - DESCRIPTION, OIL.............9-47
FILTER - INSTALLATION, OIL............9-47
FILTER - REMOVAL, OIL................9-47
FILTER CHANGE - STANDARD
PROCEDURE, ENGINE OIL...............9-47
FITTING - CONNECTING ROD............9-32
FITTING - PISTON RING................9-42
FITTING - STANDARD PROCEDURE,
MAIN BEARING.......................9-35
FITTING - STANDARD PROCEDURE,
PISTON TO CYLINDER BORE............9-30
FLASHER - DESCRIPTION, COMBINATION . 8L-19
FLASHER - OPERATION, COMBINATION . . . 8L-19
FLUSHING - STANDARD PROCEDURE,
COOLING SYSTEM - REVERSE...........7-12
FLUSHING COOLERS AND TUBES -
STANDARD PROCEDURE................7-30
FOG LAMP BULB - INSTALLATION,
FRONT.............................8L-22
FOG LAMP BULB - REMOVAL, FRONT....8L-21
FOG LAMP RELAY - DESCRIPTION,
FRONT.............................8L-22
FOG LAMP RELAY - DESCRIPTION, REAR . 8L-56
FOG LAMP RELAY - DIAGNOSIS AND
TESTING, FRONT.....................8L-23
FOG LAMP RELAY - DIAGNOSIS AND
TESTING, REAR......................8L-57
FOG LAMP RELAY - INSTALLATION,
FRONT.............................8L-24
FOG LAMP RELAY - INSTALLATION,
REAR..............................8L-58
FOG LAMP RELAY - OPERATION, FRONT . . 8L-22
FOG LAMP RELAY - OPERATION, REAR . . . 8L-57
FOG LAMP RELAY - REMOVAL, FRONT . . . 8L-24
FOG LAMP RELAY - REMOVAL, REAR....8L-58
FOG LAMP UNIT - ADJUSTMENT, FRONT . . 8L-25
FOG LAMP UNIT - INSTALLATION,
FRONT
.............................8L-25
FOG LAMP UNIT - REMOVAL, FRONT
.....8L-24
FORM-IN-PLACE GASKETS AND
SEALERS - STANDARD PROCEDURE
......9-10
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL
............................9-37
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL
...............................9-37FRONT FOG LAMP BULB -
INSTALLATION.......................8L-22
FRONT FOG LAMP BULB - REMOVAL.....8L-21
FRONT FOG LAMP RELAY -
DESCRIPTION.......................8L-22
FRONT FOG LAMP RELAY - DIAGNOSIS
AND TESTING.......................8L-23
FRONT FOG LAMP RELAY -
INSTALLATION.......................8L-24
FRONT FOG LAMP RELAY - OPERATION . . 8L-22
FRONT FOG LAMP RELAY - REMOVAL....8L-24
FRONT FOG LAMP UNIT - ADJUSTMENT . . 8L-25
FRONT FOG LAMP UNIT - INSTALLATION . . 8L-25
FRONT FOG LAMP UNIT - REMOVAL.....8L-24
FRONT LAMP BULB - INSTALLATION.....8L-27
FRONT LAMP BULB - REMOVAL.........8L-27
FRONT LAMP UNIT - INSTALLATION.....8L-28
FRONT LAMP UNIT - REMOVAL.........8L-27
FRONT MOUNT - INSTALLATION..........9-44
FRONT MOUNT - REMOVAL.............9-44
FRONT POSITION LAMP BULB -
INSTALLATION.......................8L-28
FRONT POSITION LAMP BULB -
REMOVAL..........................8L-28
FRONT SUSPENSION, SPECIAL TOOLS.....2-1
GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE AND OIL......9-9
GASKET - DIAGNOSIS AND TESTING,
CYLINDER HEAD......................9-19
GASKET SURFACE PREPARATION -
STANDARD PROCEDURE, ENGINE........9-11
GASKETS AND SEALERS - STANDARD
PROCEDURE, FORM-IN-PLACE...........9-10
HAZARD SWITCH - DESCRIPTION.......8L-28
HAZARD SWITCH - INSTALLATION.......8L-30
HAZARD SWITCH - OPERATION.........8L-29
HAZARD SWITCH - REMOVAL..........8L-29
HEAD - CLEANING, CYLINDER...........9-20
HEAD - DESCRIPTION, CYLINDER........9-19
HEAD - INSPECTION, CYLINDER..........9-21
HEAD - INSTALLATION, CYLINDER........9-21
HEAD - OPERATION, CYLINDER..........9-19
HEAD - REMOVAL, CYLINDER...........9-20
HEAD COVER - CLEANING, CYLINDER.....9-26
HEAD COVER - INSPECTION, CYLINDER . . . 9-26
HEAD COVER - INSTALLATION,
CYLINDER...........................9-26
HEAD COVER - REMOVAL, CYLINDER.....9-26
HEAD GASKET - DIAGNOSIS AND
TESTING, CYLINDER...................9-19
HEAD OFF - INSTALLATION, CYLINDER....9-28
HEAD OFF - REMOVAL, CYLINDER........9-27
HEAD ON - INSTALLATION, CYLINDER.....9-28
HEAD ON - REMOVAL, CYLINDER........9-27
HEADLAMP BULB - INSTALLATION.......8L-32
HEADLAMP BULB - REMOVAL..........8L-30
HEADLAMP HIGH BEAM RELAY -
DESCRIPTION.......................8L-33
HEADLAMP HIGH BEAM RELAY -
DIAGNOSIS AND TESTING.............8L-34
HEADLAMP HIGH BEAM RELAY -
INSTALLATION.......................8L-35
HEADLAMP HIGH BEAM RELAY -
OPERATION.........................8L-33
HEADLAMP HIGH BEAM RELAY -
REMOVAL..........................8L-34
HEADLAMP LEVELING MOTOR -
DESCRIPTION.......................8L-35
HEADLAMP LEVELING MOTOR -
INSTALLATION.......................8L-36
HEADLAMP LEVELING MOTOR -
OPERATION.........................8L-36
HEADLAMP LEVELING MOTOR -
REMOVAL..........................8L-36
HEADLAMP LEVELING SWITCH -
DESCRIPTION.......................8L-37
HEADLAMP LEVELING SWITCH -
DIAGNOSIS AND TESTING.............8L-37
HEADLAMP LEVELING SWITCH -
INSTALLATION
.......................8L-38
HEADLAMP LEVELING SWITCH -
OPERATION
.........................8L-37
HEADLAMP LEVELING SWITCH -
REMOVAL
..........................8L-38
HEADLAMP LOW BEAM RELAY -
DESCRIPTION
.......................8L-39
HEADLAMP LOW BEAM RELAY -
DIAGNOSIS AND TESTING
.............8L-40HEADLAMP LOW BEAM RELAY -
INSTALLATION.......................8L-41
HEADLAMP LOW BEAM RELAY -
OPERATION.........................8L-39
HEADLAMP LOW BEAM RELAY -
REMOVAL..........................8L-40
HEADLAMP UNIT - ADJUSTMENT........8L-42
HEADLAMP UNIT - INSTALLATION.......8L-42
HEADLAMP UNIT - REMOVAL...........8L-41
HEAT SHIELDS - DESCRIPTION..........11-4
HEATER - 2.4L - DESCRIPTION, ENGINE
BLOCK..............................7-20
HEATER - 2.4L - OPERATION, ENGINE
BLOCK..............................7-20
HIGH BEAM RELAY - DESCRIPTION,
HEADLAMP.........................8L-33
HIGH BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-34
HIGH BEAM RELAY - INSTALLATION,
HEADLAMP.........................8L-35
HIGH BEAM RELAY - OPERATION,
HEADLAMP.........................8L-33
HIGH BEAM RELAY - REMOVAL,
HEADLAMP.........................8L-34
HIGH MOUNTED STOP LAMP BULB -
INSTALLATION, CENTER...............8L-19
HIGH MOUNTED STOP LAMP BULB -
REMOVAL, CENTER...................8L-18
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER...............8L-19
HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER...................8L-19
HOAT COOLANT - DESCRIPTION..........7-18
HONING - STANDARD PROCEDURE,
CYLINDER BORE......................9-31
HOSE CLAMPS - DESCRIPTION...........7-1
HOSE CLAMPS - OPERATION.............7-2
HYDRAULIC LIFTERS - INSTALLATION.....9-29
HYDRAULIC LIFTERS - REMOVAL.........9-29
HYDROSTATIC LOCKED ENGINE -
STANDARD PROCEDURE.................9-9
INSPECTION - DIAGNOSIS AND
TESTING, ENGINE OIL LEAK..............9-4
INSPECTION, CAMSHAFT(S).............9-25
INSPECTION, CATALYTIC CONVERTER.....11-3
INSPECTION, CRANKSHAFT.............9-34
INSPECTION, CYLINDER HEAD...........9-21
INSPECTION, CYLINDER HEAD COVER.....9-26
INSPECTION, EXHAUST MANIFOLD.......9-53
INSPECTION, INTAKE MANIFOLD.........9-52
INSPECTION, OIL PUMP................9-50
INSPECTION, RADIATOR................7-24
INSPECTION, RADIATOR PRESSURE CAP . . . 7-25
INSPECTION, REMOVAL................9-28
INSPECTION, ROCKER ARMS............9-30
INSPECTION, STANDARD PROCEDURE.....9-32
INSPECTION, WATER PUMP - 2.4L........7-28
INSTALLATION - BALANCE SHAFT
TIMING.............................9-61
INSTALLATION, 2.4L...................7-20
INSTALLATION, 2.4L...................9-19
INSTALLATION, 2.4L ENGINE....7-14,7-17,7-22,
7-28
INSTALLATION, BALANCE SHAFT
CARRIER............................9-64
INSTALLATION, BALANCE SHAFT CHAIN . . . 9-64
INSTALLATION, BRAKE LAMP SWITCH....8L-18
INSTALLATION, CAMSHAFT OIL SEAL(S) . . . 9-22
INSTALLATION, CAMSHAFT(S)...........9-25
INSTALLATION, CATALYTIC CONVERTER
....11-3
INSTALLATION, CENTER HIGH MOUNTED
STOP LAMP BULB
....................8L-19
INSTALLATION, CENTER HIGH MOUNTED
STOP LAMP UNIT
....................8L-19
INSTALLATION, CLEVIS BRACKET
BUSHING
.............................2-4
INSTALLATION, CRANKSHAFT
............9-34
INSTALLATION, CRANKSHAFT OIL SEAL -
FRONT
..............................9-37
INSTALLATION, CRANKSHAFT OIL SEAL -
REAR
...............................9-39
INSTALLATION, CRANKSHAFT SPROCKET
. . 9-56
INSTALLATION, CROSS-OVER PIPE
.......11-4
INSTALLATION, CYLINDER HEAD
.........9-21
INSTALLATION, CYLINDER HEAD COVER
. . . 9-26
INSTALLATION, CYLINDER HEAD OFF
......9-28
INSTALLATION, CYLINDER HEAD ON
......9-28
KJINDEX 3
Description Group-Page Description Group-Page Description Group-Page
Page 1773 of 1803
INSTALLATION, DAYTIME RUNNING
LAMP RELAY........................8L-21
INSTALLATION, ENGINE ASSEMBLY.......9-12
INSTALLATION, ENGINE COOLANT
TEMPERATURE SENSOR................7-22
INSTALLATION, EXHAUST MANIFOLD......9-53
INSTALLATION, FRONT FOG LAMP BULB . . 8L-22
INSTALLATION, FRONT FOG LAMP
RELAY.............................8L-24
INSTALLATION, FRONT FOG LAMP UNIT . . 8L-25
INSTALLATION, FRONT LAMP BULB......8L-27
INSTALLATION, FRONT LAMP UNIT......8L-28
INSTALLATION, FRONT MOUNT..........9-44
INSTALLATION, FRONT POSITION LAMP
BULB..............................8L-28
INSTALLATION, HAZARD SWITCH........8L-30
INSTALLATION, HEADLAMP BULB.......8L-32
INSTALLATION, HEADLAMP HIGH BEAM
RELAY.............................8L-35
INSTALLATION, HEADLAMP LEVELING
MOTOR............................8L-36
INSTALLATION, HEADLAMP LEVELING
SWITCH............................8L-38
INSTALLATION, HEADLAMP LOW BEAM
RELAY.............................8L-41
INSTALLATION, HEADLAMP UNIT........8L-42
INSTALLATION, HYDRAULIC LIFTERS......9-29
INSTALLATION, INTAKE MANIFOLD........9-52
INSTALLATION, LAMP.................8L-66
INSTALLATION, LAMP BAR.............8L-66
INSTALLATION, LAMP BAR SWITCH......8L-67
INSTALLATION, LICENSE PLATE LAMP
BULB..............................8L-45
INSTALLATION, LICENSE PLATE LAMP
UNIT..............................8L-46
INSTALLATION, LOWER BALL JOINT.......2-5
INSTALLATION, LOWER CONTROL ARM
BUSHING.............................2-3
INSTALLATION, LOWER SUSPENSION
ARM BUSHING........................2-8
INSTALLATION, MUFFLER...............11-5
INSTALLATION, MULTI-FUNCTION
SWITCH............................8L-53
INSTALLATION, OIL FILTER..............9-47
INSTALLATION, OIL PAN................9-48
INSTALLATION, OIL PUMP..............9-50
INSTALLATION, PARK LAMP RELAY......8L-56
INSTALLATION, PISTON & CONNECTING
ROD................................9-41
INSTALLATION, RADIATOR..............7-24
INSTALLATION, RADIATOR FAN -
ELECTRIC...........................7-27
INSTALLATION, REAR FOG LAMP RELAY . . 8L-58
INSTALLATION, REAR LAMP BULB.......8L-59
INSTALLATION, REAR LAMP UNIT.......8L-60
INSTALLATION, REAR MOUNT...........9-45
INSTALLATION, REPEATER LAMP BULB . . . 8L-60
INSTALLATION, REPEATER LAMP UNIT . . . 8L-61
INSTALLATION, RHD....................5-1
INSTALLATION, ROCKER ARMS..........9-30
INSTALLATION, STRUCTURAL COLLAR....9-44
INSTALLATION, TIMING BELT............9-56
INSTALLATION, TIMING BELT COVER(S) . . . 9-53
INSTALLATION, TIMING BELT
TENSIONER & PULLEY.................9-59
INSTALLATION, TRAILER TOW
CONNECTOR........................8L-61
INSTALLATION, TRAILER TOW RELAY....8L-63
INSTALLATION, UPPER BALL JOINT........2-6
INSTALLATION, UPPER CONTROL ARM
BUSHINGS............................2-4
INSTALLATION, UPPER SUSPENSION
ARM BUSHING........................2-8
INSTALLATION, VIBRATION DAMPER......9-43
INTAKE MANIFOLD - DESCRIPTION.......9-51
INTAKE MANIFOLD - INSPECTION........9-52
INTAKE MANIFOLD - INSTALLATION.......9-52
INTAKE MANIFOLD - OPERATION.........9-51
INTAKE MANIFOLD - REMOVAL..........9-52
INTAKE MANIFOLD LEAKS - DIAGNOSIS
AND TESTING........................9-51
INTAKE/EXHAUST VALVES & SEATS -
CLEANING
...........................9-27
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION
........................9-27
JOINT - INSTALLATION, LOWER BALL
......2-5
JOINT - INSTALLATION, UPPER BALL
......2-6
JOINT - REMOVAL, LOWER BALL
..........2-5JOINT - REMOVAL, UPPER BALL..........2-6
LAMP - INSTALLATION................8L-66
LAMP - REMOVAL....................8L-66
LAMP BAR - DESCRIPTION.............8L-65
LAMP BAR - DIAGNOSIS AND TESTING . . . 8L-65
LAMP BAR - INSTALLATION............8L-66
LAMP BAR - OPERATION..............8L-65
LAMP BAR - REMOVAL................8L-65
LAMP BAR AIMING - STANDARD
PROCEDURE........................8L-65
LAMP BAR SWITCH - DESCRIPTION.....8L-67
LAMP BAR SWITCH - INSTALLATION.....8L-67
LAMP BAR SWITCH - REMOVAL.........8L-67
LAMP BULB - INSTALLATION, CENTER
HIGH MOUNTED STOP................8L-19
LAMP BULB - INSTALLATION, FRONT....8L-27
LAMP BULB - INSTALLATION, FRONT
FOG ...............................8L-22
LAMP BULB - INSTALLATION, FRONT
POSITION..........................8L-28
LAMP BULB - INSTALLATION, LICENSE
PLATE .............................8L-45
LAMP BULB - INSTALLATION, REAR.....8L-59
LAMP BULB - INSTALLATION, REPEATER . . 8L-60
LAMP BULB - REMOVAL, CENTER HIGH
MOUNTED STOP.....................8L-18
LAMP BULB - REMOVAL, FRONT........8L-27
LAMP BULB - REMOVAL, FRONT FOG....8L-21
LAMP BULB - REMOVAL, FRONT
POSITION..........................8L-28
LAMP BULB - REMOVAL, LICENSE
PLATE .............................8L-44
LAMP BULB - REMOVAL, REAR.........8L-59
LAMP BULB - REMOVAL, REPEATER.....8L-60
LAMP RELAY - DESCRIPTION, DAYTIME
RUNNING...........................8L-20
LAMP RELAY - DESCRIPTION, FRONT
FOG ...............................8L-22
LAMP RELAY - DESCRIPTION, PARK.....8L-54
LAMP RELAY - DESCRIPTION, REAR FOG . 8L-56
LAMP RELAY - DIAGNOSIS AND
TESTING, FRONT FOG.................8L-23
LAMP RELAY - DIAGNOSIS AND
TESTING, PARK......................8L-55
LAMP RELAY - DIAGNOSIS AND
TESTING, REAR FOG..................8L-57
LAMP RELAY - INSTALLATION, DAYTIME
RUNNING...........................8L-21
LAMP RELAY - INSTALLATION, FRONT
FOG ...............................8L-24
LAMP RELAY - INSTALLATION, PARK.....8L-56
LAMP RELAY - INSTALLATION, REAR
FOG ...............................8L-58
LAMP RELAY - OPERATION, DAYTIME
RUNNING...........................8L-20
LAMP RELAY - OPERATION, FRONT FOG . . 8L-22
LAMP RELAY - OPERATION, PARK.......8L-54
LAMP RELAY - OPERATION, REAR FOG . . . 8L-57
LAMP RELAY - REMOVAL, DAYTIME
RUNNING...........................8L-21
LAMP RELAY - REMOVAL, FRONT FOG . . . 8L-24
LAMP RELAY - REMOVAL, PARK........8L-55
LAMP RELAY - REMOVAL, REAR FOG....8L-58
LAMP SWITCH - DESCRIPTION, BACKUP . . 8L-15
LAMP SWITCH - DESCRIPTION, BRAKE . . . 8L-16
LAMP SWITCH - DIAGNOSIS AND
TESTING, BACKUP....................8L-15
LAMP SWITCH - DIAGNOSIS AND
TESTING, BRAKE.....................8L-17
LAMP SWITCH - INSTALLATION, BRAKE . . 8L-18
LAMP SWITCH - OPERATION, BACKUP . . . 8L-15
LAMP SWITCH - OPERATION, BRAKE.....8L-16
LAMP SWITCH - REMOVAL, BRAKE......8L-17
LAMP UNIT - ADJUSTMENT, FRONT FOG . . 8L-25
LAMP UNIT - INSTALLATION, CENTER
HIGH MOUNTED STOP................8L-19
LAMP UNIT - INSTALLATION, FRONT.....8L-28
LAMP UNIT - INSTALLATION, FRONT
FOG ...............................8L-25
LAMP UNIT - INSTALLATION, LICENSE
PLATE .............................8L-46
LAMP UNIT - INSTALLATION, REAR......8L-60
LAMP UNIT - INSTALLATION, REPEATER
. . 8L-61
LAMP UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP
.....................8L-19
LAMP UNIT - REMOVAL, FRONT
.........8L-27
LAMP UNIT - REMOVAL, FRONT FOG
.....8L-24
LAMP UNIT - REMOVAL, LICENSE PLATE
. . 8L-45LAMP UNIT - REMOVAL, REAR..........8L-59
LAMP UNIT - REMOVAL, REPEATER......8L-61
LAMPS/LIGHTING - EXTERIOR -
DESCRIPTION........................8L-2
LAMPS/LIGHTING - EXTERIOR -
DIAGNOSIS AND TESTING..............8L-7
LAMPS/LIGHTING - EXTERIOR -
OPERATION..........................8L-5
LAMPS/LIGHTING - EXTERIOR -
SPECIFICATIONS.....................8L-15
LASH ADJUSTER (TAPPET) NOISE
DIAGNOSIS - DIAGNOSIS AND
TESTING............................9-28
LEAK INSPECTION - DIAGNOSIS AND
TESTING, ENGINE OIL...................9-4
LEAKAGE TEST - DIAGNOSIS AND
TESTING, CYLINDER COMBUSTION
PRESSURE...........................9-3
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-2
LEAKS - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD....................9-51
LEVEL CHECK, STANDARD PROCEDURE
- ENGINE OIL........................9-47
LEVELING MOTOR - DESCRIPTION,
HEADLAMP.........................8L-35
LEVELING MOTOR - INSTALLATION,
HEADLAMP.........................8L-36
LEVELING MOTOR - OPERATION,
HEADLAMP.........................8L-36
LEVELING MOTOR - REMOVAL,
HEADLAMP.........................8L-36
LEVELING SWITCH - DESCRIPTION,
HEADLAMP...........................8L-37
LEVELING SWITCH - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-37
LEVELING SWITCH - INSTALLATION,
HEADLAMP.........................8L-38
LEVELING SWITCH - OPERATION,
HEADLAMP.........................8L-37
LEVELING SWITCH - REMOVAL,
HEADLAMP.........................8L-38
LICENSE PLATE LAMP BULB -
INSTALLATION.......................8L-45
LICENSE PLATE LAMP BULB - REMOVAL . . 8L-44
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-46
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-45
LIFTERS - INSTALLATION, HYDRAULIC....9-29
LIFTERS - REMOVAL, HYDRAULIC........9-29
LOCKED ENGINE - STANDARD
PROCEDURE, HYDROSTATIC..............9-9
LOW BEAM RELAY - DESCRIPTION,
HEADLAMP.........................8L-39
LOW BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-40
LOW BEAM RELAY - INSTALLATION,
HEADLAMP.........................8L-41
LOW BEAM RELAY - OPERATION,
HEADLAMP.........................8L-39
LOW BEAM RELAY - REMOVAL,
HEADLAMP.........................8L-40
LOWER BALL JOINT - INSTALLATION......2-5
LOWER BALL JOINT - REMOVAL..........2-5
LOWER CONTROL ARM BUSHING -
INSTALLATION.........................2-3
LOWER CONTROL ARM BUSHING -
REMOVAL............................2-2
LOWER SUSPENSION ARM BUSHING -
INSTALLATION.........................2-8
LOWER SUSPENSION ARM BUSHING -
REMOVAL............................2-7
LUBRICATION - DESCRIPTION...........9-46
LUBRICATION - OPERATION
.............9-46
MAIN BEARING - FITTING - STANDARD
PROCEDURE
.........................9-35
MANIFOLD - CLEANING, EXHAUST
........9-53
MANIFOLD - DESCRIPTION, EXHAUST
.....9-53
MANIFOLD - DESCRIPTION, INTAKE
.......9-51
MANIFOLD - INSPECTION, EXHAUST
......9-53
MANIFOLD - INSPECTION, INTAKE
........9-52
MANIFOLD - INSTALLATION, EXHAUST
....9-53
MANIFOLD - INSTALLATION, INTAKE
......9-52
MANIFOLD - OPERATION, EXHAUST
.......9-53
MANIFOLD - OPERATION, INTAKE
........9-51
MANIFOLD - REMOVAL, EXHAUST
........9-53
MANIFOLD - REMOVAL, INTAKE
..........9-52
4 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page
Page 1774 of 1803
MANIFOLD LEAKS - DIAGNOSIS AND
TESTING, INTAKE.....................9-51
MEASURING BEARING CLEARANCE
USING PLASTIGAGE - STANDARD
PROCEDURE.........................9-11
MECHANICAL - DIAGNOSIS AND
TESTING, ENGINE......................9-7
MOTOR - DESCRIPTION, HEADLAMP
LEVELING..........................8L-35
MOTOR - INSTALLATION, HEADLAMP
LEVELING..........................8L-36
MOTOR - OPERATION, HEADLAMP
LEVELING..........................8L-36
MOTOR - REMOVAL, HEADLAMP
LEVELING..........................8L-36
MOUNT - INSTALLATION, FRONT.........9-44
MOUNT - INSTALLATION, REAR..........9-45
MOUNT - REMOVAL, FRONT.............9-44
MOUNT - REMOVAL, REAR..............9-45
MOUNTED STOP LAMP BULB -
INSTALLATION, CENTER HIGH..........8L-19
MOUNTED STOP LAMP BULB -
REMOVAL, CENTER HIGH..............8L-18
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH..........8L-19
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH..............8L-19
MOUNTING - DESCRIPTION, ENGINE......9-44
MUFFLER - DESCRIPTION...............11-4
MUFFLER - INSTALLATION..............11-5
MUFFLER - REMOVAL..................11-4
MULTI-FUNCTION SWITCH -
DESCRIPTION.......................8L-46
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING.......................8L-50
MULTI-FUNCTION SWITCH -
INSTALLATION.......................8L-53
MULTI-FUNCTION SWITCH - OPERATION . . 8L-48
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-53
NOISE DIAGNOSIS - DIAGNOSIS AND
TESTING, LASH ADJUSTER (TAPPET)......9-28
OFF - INSTALLATION, CYLINDER HEAD....9-28
OFF - REMOVAL, CYLINDER HEAD........9-27
OIL AND FILTER CHANGE - STANDARD
PROCEDURE, ENGINE..................9-47
OIL FILTER - DESCRIPTION.............9-47
OIL FILTER - INSTALLATION.............9-47
OIL FILTER - REMOVAL.................9-47
OIL GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE..............9-9
OIL LEAK INSPECTION - DIAGNOSIS
AND TESTING, ENGINE..................9-4
OIL LEVEL CHECK, STANDARD
PROCEDURE - ENGINE.................9-47
OIL PAN - INSTALLATION...............9-48
OIL PAN - REMOVAL...................9-48
OIL PRESSURE CHECKING - DIAGNOSIS
AND TESTING, ENGINE.................9-46
OIL PRESSURE SENSOR/SWITCH -
DESCRIPTION........................9-48
OIL PRESSURE SENSOR/SWITCH -
OPERATION..........................9-48
OIL PUMP - ASSEMBLY................9-50
OIL PUMP - CLEANING.................9-49
OIL PUMP - DISASSEMBLY.............9-49
OIL PUMP - INSPECTION...............9-50
OIL PUMP - INSTALLATION.............9-50
OIL PUMP - REMOVAL.................9-49
OIL SEAL - FRONT - INSTALLATION,
CRANKSHAFT........................9-37
OIL SEAL - FRONT - REMOVAL,
CRANKSHAFT........................9-37
OIL SEAL - REAR - INSTALLATION,
CRANKSHAFT........................9-39
OIL SEAL - REAR - REMOVAL,
CRANKSHAFT........................9-38
OIL SEAL(S) - INSTALLATION,
CAMSHAFT..........................9-22
OIL SEAL(S) - REMOVAL, CAMSHAFT.....9-22
ON-BOARD DIAGNOSTICS (OBD) -
DIAGNOSIS AND TESTING...............7-2
OPERATION, BACKUP LAMP SWITCH.....8L-15
OPERATION, BALANCE SHAFT
...........9-59
OPERATION, BRAKE LAMP SWITCH
......8L-16
OPERATION, CAMSHAFT(S)
.............9-23
OPERATION, COMBINATION FLASHER
....8L-19
OPERATION, COOLANT RECOVERY
PRESS CONTAINER
....................7-20OPERATION, COOLING SYSTEM...........7-2
OPERATION, CRANKSHAFT..............9-33
OPERATION, CYLINDER HEAD...........9-19
OPERATION, DAYTIME RUNNING LAMP
RELAY.............................8L-20
OPERATION, DESCRIPTION..............7-20
OPERATION, ENGINE BLOCK HEATER -
2.4L................................7-20
OPERATION, ENGINE COOLANT
TEMPERATURE SENSOR................7-21
OPERATION, EXHAUST MANIFOLD........9-53
OPERATION, FRONT FOG LAMP RELAY . . . 8L-22
OPERATION, HAZARD SWITCH..........8L-29
OPERATION, HEADLAMP HIGH BEAM
RELAY.............................8L-33
OPERATION, HEADLAMP LEVELING
MOTOR............................8L-36
OPERATION, HEADLAMP LEVELING
SWITCH............................8L-37
OPERATION, HEADLAMP LOW BEAM
RELAY.............................8L-39
OPERATION, HOSE CLAMPS..............7-2
OPERATION, INTAKE MANIFOLD..........9-51
OPERATION, LAMP BAR...............8L-65
OPERATION, LAMPS/LIGHTING -
EXTERIOR...........................8L-5
OPERATION, LUBRICATION..............9-46
OPERATION, MULTI-FUNCTION SWITCH . . . 8L-48
OPERATION, OIL PRESSURE SENSOR/
SWITCH..............................9-48
OPERATION, PARK LAMP RELAY........8L-54
OPERATION, PISTON & CONNECTING
ROD................................9-40
OPERATION, RADIATOR FAN - ELECTRIC . . . 7-26
OPERATION, RADIATOR PRESSURE CAP . . . 7-25
OPERATION, REAR FOG LAMP RELAY....8L-57
OPERATION, TRAILER TOW RELAY.......8L-62
OPERATION, WATER PUMP - 2.4L........7-27
PAN - INSTALLATION, OIL...............9-48
PAN - REMOVAL, OIL..................9-48
PARK LAMP RELAY - DESCRIPTION......8L-54
PARK LAMP RELAY - DIAGNOSIS AND
TESTING...........................8L-55
PARK LAMP RELAY - INSTALLATION.....8L-56
PARK LAMP RELAY - OPERATION.......8L-54
PARK LAMP RELAY - REMOVAL.........8L-55
PERFORMANCE - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS............9-5
PIPE - INSTALLATION, CROSS-OVER......11-4
PIPE - REMOVAL, CROSS-OVER..........11-4
PISTON & CONNECTING ROD -
DESCRIPTION........................9-40
PISTON & CONNECTING ROD -
INSTALLATION........................9-41
PISTON & CONNECTING ROD -
OPERATION..........................9-40
PISTON & CONNECTING ROD -
REMOVAL...........................9-40
PISTON RING, FITTING.................9-42
PISTON TO CYLINDER BORE FITTING -
STANDARD PROCEDURE................9-30
PLASTIGAGE - STANDARD PROCEDURE,
MEASURING BEARING CLEARANCE
USING..............................9-11
PLATE LAMP BULB - INSTALLATION,
LICENSE...........................8L-45
PLATE LAMP BULB - REMOVAL,
LICENSE...........................8L-44
PLATE LAMP UNIT - INSTALLATION,
LICENSE...........................8L-46
PLATE LAMP UNIT - REMOVAL, LICENSE . . 8L-45
PLAY - STANDARD PROCEDURE,
CRANKSHAFT END....................9-33
PLUGS - STANDARD PROCEDURE,
ENGINE CORE AND OIL GALLERY.........9-9
POSITION LAMP BULB - INSTALLATION,
FRONT.............................8L-28
POSITION LAMP BULB - REMOVAL,
FRONT
.............................8L-28
PRELIMINARY CHECKS - DIAGNOSIS
AND TESTING
.........................7-2
PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET
SURFACE
............................9-11
PRESS CONTAINER - DESCRIPTION,
COOLANT RECOVERY
..................7-20
PRESS CONTAINER - OPERATION,
COOLANT RECOVERY
..................7-20PRESSURE CAP - CLEANING, RADIATOR . . . 7-25
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-25
PRESSURE CAP - DIAGNOSIS AND
TESTING, RADIATOR...................7-25
PRESSURE CAP - INSPECTION,
RADIATOR...........................7-25
PRESSURE CAP - OPERATION,
RADIATOR...........................7-25
PRESSURE CHECKING - DIAGNOSIS AND
TESTING, ENGINE OIL..................9-46
PRESSURE LEAKAGE TEST - DIAGNOSIS
AND TESTING, CYLINDER
COMBUSTION.........................9-3
PRESSURE SENSOR/SWITCH -
DESCRIPTION, OIL....................9-48
PRESSURE SENSOR/SWITCH -
OPERATION, OIL......................9-48
PRESSURE TEST - DIAGNOSIS AND
TESTING, CYLINDER COMPRESSION.......9-3
PULLEY - INSTALLATION, TIMING BELT
TENSIONER..........................9-59
PULLEY - REMOVAL, TIMING BELT
TENSIONER..........................9-59
PUMP - 2.4L - DESCRIPTION, WATER.....7-27
PUMP - 2.4L - INSPECTION, WATER......7-28
PUMP - 2.4L - OPERATION, WATER.......7-27
PUMP - ASSEMBLY, OIL................9-50
PUMP - CLEANING, OIL................9-49
PUMP - DISASSEMBLY, OIL.............9-49
PUMP - INSPECTION, OIL...............9-50
PUMP - INSTALLATION, OIL.............9-50
PUMP - REMOVAL, OIL.................9-49
RADIATOR - CLEANING.................7-24
RADIATOR - DESCRIPTION..............7-22
RADIATOR - INSPECTION...............7-24
RADIATOR - INSTALLATION.............7-24
RADIATOR - REMOVAL.................7-22
RADIATOR FAN - ELECTRIC -
DESCRIPTION........................7-26
RADIATOR FAN - ELECTRIC -
INSTALLATION........................7-27
RADIATOR FAN - ELECTRIC -
OPERATION..........................7-26
RADIATOR FAN - ELECTRIC - REMOVAL . . . 7-26
RADIATOR PRESSURE CAP - CLEANING . . . 7-25
RADIATOR PRESSURE CAP -
DESCRIPTION........................7-25
RADIATOR PRESSURE CAP - DIAGNOSIS
AND TESTING........................7-25
RADIATOR PRESSURE CAP -
INSPECTION.........................7-25
RADIATOR PRESSURE CAP - OPERATION . . 7-25
REAR - INSTALLATION, CRANKSHAFT
OIL SEAL............................9-39
REAR - REMOVAL, CRANKSHAFT OIL
SEAL...............................9-38
REAR FOG LAMP RELAY - DESCRIPTION . . 8L-56
REAR FOG LAMP RELAY - DIAGNOSIS
AND TESTING.......................8L-57
REAR FOG LAMP RELAY -
INSTALLATION.......................8L-58
REAR FOG LAMP RELAY - OPERATION . . . 8L-57
REAR FOG LAMP RELAY - REMOVAL.....8L-58
REAR LAMP BULB - INSTALLATION......8L-59
REAR LAMP BULB - REMOVAL..........8L-59
REAR LAMP UNIT - INSTALLATION......8L-60
REAR LAMP UNIT - REMOVAL..........8L-59
REAR MOUNT - INSTALLATION..........9-45
REAR MOUNT - REMOVAL..............9-45
REAR SUSPENSION, SPECIAL TOOLS......2-6
RECOVERY PRESS CONTAINER -
DESCRIPTION, COOLANT...............7-20
RECOVERY PRESS CONTAINER -
OPERATION, COOLANT.................7-20
REFILLING COOLING SYSTEM -
STANDARD PROCEDURE................7-11
RELAY - DESCRIPTION, DAYTIME
RUNNING LAMP.....................8L-20
RELAY - DESCRIPTION, FRONT FOG
LAMP..............................8L-22
RELAY - DESCRIPTION, HEADLAMP
HIGH BEAM
.........................8L-33
RELAY - DESCRIPTION, HEADLAMP LOW
BEAM
..............................8L-39
RELAY - DESCRIPTION, PARK LAMP
.....8L-54
RELAY - DESCRIPTION, REAR FOG LAMP
. 8L-56
RELAY - DESCRIPTION, TRAILER TOW
....8L-62
KJINDEX 5
Description Group-Page Description Group-Page Description Group-Page