light JEEP RENEGADE 2015 1.G Owners Manual

3. By pushing the electrical connector tab remove the
electrical connector.
4. Rotate the bulb counterclockwise, and then replace the
bulb.
5. Insert the new bulb in the socket, making sure the bulb
is locked into place.
6. Reconnect the electrical connector.
7. Reinstall the access door.
Side Indicators
Front Side Indicators
To replace the bulb proceed as follows:
1. Operating from inside the engine compartment using
a suitable tool release the retaining clip.Fog Light Assembly
1—BulbSocket2 — Electrical Connector3—Bulb
442 IN CASE OF EMERGENCY

4. Remove the bulb from the bulb socket by pulling the
bulb straight out.
5. Insert the new bulb, making sure that it is locked into
place
6. Reinstall the socket in to the transparent lens assembly.
7. Reinstall the cover on the outside rear view mirror,
making sure it is locked into place.
Rear Tail Lamps
Contain the following:
•Position lights
•Stop lights
•Direction indicator
•REVERSE lightsBulb And Socket Assembly
1—Bulb2—BulbSocket
448 IN CASE OF EMERGENCY

7. Replace the bulb as necessary.8. Insert the new bulb, making sure it is properly locked;
9. Reassemble the lamp assembly on the rear tail lamp
housing, tightening the screws.
10. Reposition the rear tail lamp on the car.
11. Secure the fastener of the rear tail lamp and reconnect
the electrical connector.
12. Reinstall the door making sure of its correct locked
13. Finally close the tailgate.
3th Stop Lamp
The CHMSL is LED. For their replacement see your
authorized dealer.Rear Tail Lamp Holder
1—TailLight2 — Reverse Bulb3—PositionLight/StopLight/TurnSignal
8
IN CASE OF EMERGENCY 451

License Plate Lights
To replace the bulbs proceed as follows:
1. Using a suitable tool remove the license plate lens.
2. Remove the bulbs from the individual side contacts.
License Plate Light Location
License Plate Light
452 IN CASE OF EMERGENCY

3. Insert the new bulbs, and ensure that they are properly
locked between the contacts.
4. Reinstall the license plate lens.
NOTE:If removal the license plate lens using a screw-
driver, be sure to cover the tip of the screwdriver with a
cloth so no damage is done to the lenses or the vehicle
paint.
Replacement Of A Internal Lamp
Front Courtesy Light
To replace the bulbs proceed as follows:
1. Using a suitable tool remove the front courtesy light as
shown.
2. Release the retainer clips and bulb housing as shown.
Front Courtesy Light Housing8
IN CASE OF EMERGENCY 453

5. Reassemble the bulb housing and courtesy light hous-
ing making sure that they are properly locked.
6. Install the front courtesy light making sure that it is
properly locked.
Dome Light Vanity Mirror
To replace the bulbs proceed as follows:
1. Lift the cover of the mirror and pull out the visor
mirror light cover.
2. Replace the bulb, releasing it from the side contacts,
and then insert the new bulb, making sure that it is
properly locked between the contacts.
3. Reinstall the visor mirror light cover making sure that
it is properly locked.
4. Finally lower the visor mirror cover to the mirror.
Visor
1—VisorMirrorCover2—VisorMirrorLight
8
IN CASE OF EMERGENCY 455

Dome Light Glove Compartment
To replace the bulb proceed as follows:
1. Open the glove compartment;
2. Place your fingers inside the light assembly, pull the
bulb to replace it.
3. Insert the new bulb, making sure it is properly locked.
Rear Dome Light — Without Retractable Roof
To replace the bulbs proceed as follows:
1. Using a suitable tool release the lamp assembly at both
the ends.
2. Open the flap and replace the bulb.
Bulb Removal/Installation
456 IN CASE OF EMERGENCY

3. Insert the new bulb, locking it between the contacts.
4. Reinstall the dome light.
Dome Light — MY SKY
To replace the bulbs proceed as follows:
1. Lower the handle in the direction shown remove the
dome light.
2. Replace the bulb by removing it from the side contacts.
Rear Dome Light Housing
1—Bulb2 — Flap
Retractable Roof Light
8
IN CASE OF EMERGENCY 457

3. Insert the new bulb, locking it between the contacts.
4. Reinstall the dome light.
Interior Cargo Lights
To replace the bulbs proceed as follows:
1. Open the luggage compartment and remove the dome
light assembly.
2. Open the light cover and replace the bulb.
Bulb
Light Cover
458 IN CASE OF EMERGENCY

3. Close the light cover over the bulb.
4. Reinstall the dome light in its correct position.
WARNING!
•Before proceeding with the replacement of the
lamp wait for the exhaust pipes are cool: DANGER
OF BURNS!
•Modifications or repair of the electrical system
performed incorrectly and without taking into ac-
count the technical characteristics can cause mal-
functions with the risk of fire.
•Halogen lamps contain gas under pressure, in the
event of breakage be careful of the projection of
fragments of glass.
(Continued)
WARNING!(Continued)
•Halogen lamps must be handled by touching only
the metallic part. If the transparent bulb is in
contact with the fingers, reduces the intensity of
the emitted light and you can also affect the life of
the lamp. In case of accidental contact, rub the bulb
with a cloth dampened with alcohol and allow to
dry.
8
IN CASE OF EMERGENCY 459