warning light KIA BORREGO 2017 Service Manual

481
Features of your vehicle
Ice Warning Light (if equipped)
This warning light blinks 5 times and
then illuminates, and also warning
chime sounds 1 time:
When the temperature on the Outside Temperature Gauge is
below approximately 4 O
C (39.2 O
F)
with the ignition switch or Engine
Start/Stop button in the ON posi-tion.
✽✽ NOTICE
If the ice warning light appears
while driving, you should drive
more attentively and safely refrain-
ing from over-speeding, rapid accel-
eration, sudden braking or sharp
turning, etc.
Indicator Lights
Electronic Stability Control (ESC) Indicator Light (if equipped)
This indicator light illuminates:
Once you set the ignition switch or Engine Start/Stop Button to the ON position.
- It illuminates for approximately 3seconds and then goes off.
When there is a malfunction with the ESC system.
In this case, we recommend that
you have the vehicle inspected by
an authorized Kia dealer.
This indicator light blinks:
While the ESC is operating.
For more details, refer to “Electronic
Stability Control (ESC)” in chapter 6.
Electronic Stability Control (ESC) OFF Indicator Light (if equipped)
This indicator light illuminates:
Once you set the ignition switch or Engine Start/Stop Button to the ON position.
- It illuminates for approximately 3seconds and then goes off.
When you deactivate the ESC sys- tem by pressing the ESC OFF but- ton.
For more details, refer to “Electronic
Stability Control (ESC)” in chapter 6.

Features of your vehicle
84
4
High beam assist
indicator (if equipped)
This warning light illuminates :
When the high-Beam is on with the light switch in the AUTO light posi- tion.
If your vehicle detects oncoming or preceding vehicles, the high beam
assist system will switch the high
beam to low beam automatically.
For more details, refer to “High beam
assist” in chapter 4.
Low Beam Indicator Light (if equipped)
This indicator light illuminates:
When the headlights are on.
Glow Indicator Light(Diesel Engine)
This indicator light illuminates:
When the engine is being preheat- ed with the ignition switch or
Engine Start/Stop Button in the ONposition.
- The engine can be started afterthe glow indicator light goes off.
- The illumination time varies with the engine coolant temperature,
air temperature, and battery con-dition.
If the indicator light remains on or
blinks after the engine has warmed
up or while driving, there may a mal-function with the engine preheatingsystem.
In this case, we recommend that you
have the vehicle inspected by an
authorized Kia dealer.
✽✽ NOTICE - Engine Preheating
If the engine does not start within 10
seconds after the preheating is com-
pleted, set the ignition switch or
Engine Start/Stop Button to the
LOCK or OFF position for 10 sec-
onds and then to the ON position in
order to preheat the engine again.

485
Features of your vehicle
Lane Departure WarningSystem (LDWS) Indicator Light (if equipped)
This indicator light illuminates:
[White] When the lane departure warning system does not detect
the lane line.
[Green] When you activate the lane departure warning system by
pressing the LDWS button.
When blinking in Green, LDWS is
in warning condition.
[Yellow] When there is a malfunc- tion with the lane departure warn-ing system.
In this case, we recommend that you
have the vehicle inspected by an
authorized Kia dealer. ❈ For more details, refer to “Lane
Departure Warning System
(LDWS)” in chapter 6.
4WD LOW indicator
(if equipped)
When the ignition switch is turned to
the ON position, the 4WD LOW indi-cator will illuminate and then go off in
a few seconds. The 4WD LOW indi-
cator illuminates when the transfer
shift knob is set to the 4L(Low-speed
4-wheel drive) position. ❈ For more details, refer to “Four
wheel drive (4WD)” in chapter 6.
4WD HI indicator
(if equipped)
When the ignition switch is turned to the ON position, the 4WD HI indica-tor will illuminate and then go off in a
few seconds. The 4WD HI indicator
illuminates when the transfer shiftknob is set to the 4H(High-speed 4-
wheel drive) position. ❈ For more details, refer to “Four
wheel drive (4WD)” in chapter 6.
4WD
LOW4WD HI

Features of your vehicle
96
4
The rearview camera will activate
when the back-up light is ON with the
ignition switch ON and the shift lever
in the R (Reverse) position. This system is a supplemental sys-
tem that shows behind the vehicle
through the rearview display mirror
while backing-up. ❈
If your vehicle is equipped with
AVN(Audio, Video and Navigation)
system, rearview display will show
behind the vehicle through the
AVN monitor while backing-up.
Refer to a separately supplied
manual for detailed information.
WARNING
This system is a supplemen- tary function only. It is the responsibility of the driver to
always check the inside/out-
side rearview mirror and the
area behind the vehicle before
and while backing up becausethere is a dead zone that can't
be seen by the camera.
Always keep the camera lens clean. If lens is covered with
foreign matter, the camera
may not operate normally.
OHM046062L
OHM046061L
REARVIEW CAMERA (IF EQUIPPED)

4101
Features of your vehicle
High beam operation
To turn on the high beam headlamp,
push the lever away from you. The
lever will return to its original position. The high beam indicator will light when the headlight high beams are
switched on.
To prevent the battery from being
discharged, do not leave the lights
on for a prolonged time while the
engine is not running.To flash the headlights, pull the lever
towards you. It will return to the nor-
mal (low beam) position when
released. The headlight switch doesnot need to be on to use this flashing
feature.
OHM046069
WARNING
Do not use high beam when
there are other vehicles. Usinghigh beam could obstruct the
other driver’s vision.
OHM046068

4103
Features of your vehicle
CAUTION
The system may not operate nor-mally in the below conditions.
When the light from the on-com- ing or front vehicle is not detect-ed because of lamp damage,hidden from sight, etc.
When the lamp of the on-com- ing or front vehicle is coveredwith dust, snow or water.
When the light from the on-com- ing or front vehicle is not detect-ed because of exhaust fume,smoke, fog, snow, etc.
When the front window is cov- ered with foreign matters suchas ice, dust, fog, or is damaged.
When there is a similar shape lamp with the front vehicle’slamps.
When it is hard to see because of fog, heavy rain or snow.
When the headlamp is not repaired or replaced at anauthorized dealer.
(Continued)
(Continued)
When headlamp aiming is not properly adjusted.
When driving on a narrow curved road or rough road.
When driving downhill or uphill. When only part of the vehicle in front is visible on a crossroad orcurved road.
When there is a traffic light, reflecting sign, flashing sign ormirror.
When the road conditions are bad such as being wet or cov-ered with snow.
When the front vehicle’s head- lamps are off but the fog lampson.
When a vehicle suddenly appears from a curve.
When the vehicle is tilted from a flat tire or being towed.
When the LDWS (lane departure warning system) warning lightilluminates. (if equipped)WARNING
Do not place any accessories, stickers or tint the windshield.
Have the windshield glass replaced from an authorized
dealer.
Do not remove or impact relat- ed parts of the High BeamAssist system.
Be careful that water doesn’t get into the High Beam Assistunit.
Do not place objects on the dashboard that reflects light
such as mirrors, white paper,
etc. The system may malfunc-tion if sunlight is reflected.
At times, the Smart High Beam system may not work
properly, always check the
road conditions for your safe-
ty. When the system does not
operate normally, manually
change between the high
beam and low beam.

Features of your vehicle
106
4
Headlight leveling device (if equipped)
Manual type
To adjust the headlight beam level
according to the number of passen-
gers and loading weight in the luggage
area, turn the beam leveling switch.
The higher the number of the switch
position, the lower the headlight
beam level. Always keep the head-
light beam at the proper leveling
position, or headlights may dazzle
other road users. Listed below are the examples of
proper switch settings. For loadingconditions other than those listed
below, adjust the switch position so
that the beam level may be the near-est as the condition obtained accord-ing to the list.
Automatic type
It automatically adjusts the headlight
beam level according to the number
of passengers and loading weight inthe luggage area.
And it offers proper headlight beam
under various conditions.
OHM048223N
Loading conditionSwitch
position
Driver only0
Driver + Front passenger0
Driver + Front passenger+
3rd row passenger1
Full passengers
(Including driver)1
Full passengers (including driv-
er) + Maximum permissible load-ing2
Driver + Maximum permissible loading3
WARNING
If it does not work properly even
though your car is inclined
backward according to passen-
ger's posture, or the headlightbeam is irradiated to the high or
low position, we recommend
that the system be inspected by
an authorized Kia dealer. Do not attempt to inspect or
replace the wiring yourself.

Features of your vehicle
110
4
Headlight washer (if equipped)
To operate the headlight washer,
press the headlight washer button. It
will operate when the headlight switchis in the first or second position and
the ignition switch is in the ON posi-
tion. The washer fluid will spray on the
headlights.
Also, if you pull the wiper lever towards
you for about 1 second, when the
headlights are on, the headlight wash-
er will operate. (if equipped)✽✽
NOTICE
 Check the headlight washers peri- odically to confirm that the wash-
er fluid is being sprayed properly
onto the headlight lenses.
 The headlight washer may not work temporarily if it freezes after
a car wash, rain or snow in the
winter. But it will work normally
after it defrosts.WARNING
Do not use the washer in freez-
ing temperatures without firstwarming the windshield with
the defrosters; the washer solu-
tion could freeze on the wind-
shield and obscure your vision.
CAUTION
To prevent possible damage to the wipers or windshield,do not operate the wiperswhen the windshield is dry.
To prevent damage to the wiper blades, do not use gasoline,kerosene, paint thinner, or other solvents on or near them.
To prevent damage to thewiper arms and other compo- nents, do not attempt to movethe wipers manually.
To prevent possible damage to the wipers and washer sys-tem, use anti-freezing washerfluids in the winter season or cold weather.
OHM046072N

Features of your vehicle
112
4
INTERIOR LIGHT
Map lamp
Push the lens to turn the map lamp
on or off. This light produces a spot
beam for convenient use as a maplamp at night or as a personal lamp
for the driver and the front passen-
ger. Room lamp
DOOR: The light comes on when
any door (or tailgate) is opened regardless of the
ignition switch position.
When doors are unlocked
by the transmitter (or smart
key), the light comes on for
approximately 30 seconds
as long as any door is not
opened. The light goes out
gradually after approximate-ly 30 seconds if the door is
closed. However, if the igni-
tion switch is ON or all doors
are locked, the light will turn
off immediately.
CAUTION
Do not use the interior lights for
extended periods when theengine is not running.
It may cause battery discharge.
OHM046077NOHM046079N
WARNING
Do not use the interior lights when driving in the dark.Accidents could happen because
the view may be ob scured by
interior lights.

4113
Features of your vehicle
If a door is opened with the
ignition switch in the ACC orLOCK position, the light
stays on for about 20 min-
utes. However, if a door isopened with the ignition
switch in the ON position,
the light stays on continu-
ously.
: The light stays off at all times.
: The light stays on at all times. Luggage lamp (if equipped)
The light comes on when the
tailgate is opened.

OFF : The light stays off at all times. Door courtesy lamp (if equipped)
The door courtesy lamp comes ON when the door is opened to assist
entering or exiting the vehicle. It also
serves as a warning to passing vehi-
cles that the vehicle door is open.
OHM048080
OHM048081