sensor KIA CARNIVAL 2007 Workshop Manual

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
1.Remove the automatic transaxle assembly.
2. Remove the valve body cover(refer to the overhaul manual).
3. Disconnect the oil temperature sensor connector.
4. Remove the oil temperature sensor(B), loosening the mounting bolt(A).
5.Replace the sensor with the new one and reassemble the rest of the parts.
INSPECTION
1.Remove the oil temperature sensor(A).
2.Measure the resistance between the terminal 1 and 2 of the sensor connector.
Temp.[°C(°F)] Resistance(KΩ)
0(32)
100(212) 18.6
0.63
3.
If the value is out of the specfication, replace the oil temperature sensor.

5.Disconnect the vehicle speed sensor connector (A) and the back up lamp switch(B).
6.Disconnect the shift cable assembly(A) after remaing the clips(B) and pins(C).
7.Remove the wire harness bracket(A).

26.Install the wire harness bracket(b).
27.Install the shift cable assembly (A) with the clips(B) and pins(C).
28.Install the vehicle speed sensor connector (A) and the back up lamp switch(B).
29.Install the battery tray(B) by removing the four mounting bolts(A).

30.Install the air cleaner assembly(B) by tightening the two mounting bolts(A).
31.Reassemble the air cleaner filter, install the air cleaner upper body(B) and connect the air flow sensor
connector(A).
32.Install the battery(A).

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Raise the vehicle and remove the wheel & tire assembly (A) from the front hub assembly (B).
Tightening torque Nm (Kgf.m, lb - ft):
90 ~ 110 (9.0 ~ 11.0, 65 ~ 80)
2.Remove the wheel speed sensor & wire (A) by loosening the bolts.
3.Disconnect the brake hose (A) from the strut assembly.
4.Unstake the driveshaft lock nut using a chisel and hammer.

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Release the parking brake.
2. Remove the wheel & tire assembly.
Tightening torque Nm (kgf.m, lb - ft):
90 ~ 110 (9.0 ~ 11.0, 65 ~ 80)
3.Support lower part of the lower arm (A) using a jack and remove the bolt & nut (B).
Tightening torque Nm (kgf.m, lb - ft):
160 ~ 180 (16.0 ~ 18.0, 116 ~ 130)
4.Remove the coil spring (A) and upper pad.
5.Remove the wheel speed sensor (A).

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Loosen the wheel nuts slightly.
Raise the front of the vehicle, and make sure it is securely supported.
2. Remove the front wheel and tire (A) from front hub (B).
Be careful not to damage to the hub bolts (C) when removing the front wheel and tire (A).
3. Remove the brake hose bracket bolt (A, B) from the front strtu assembly.
4.Remove the speed sensor (A) and wire (B) bolts from the front knuckle.
5.Remove the front stabilizer link (A) nut (B) from the strut assembly.

2.Install the front strut assembly (A) bolts (B) to the front knuckle.
Tightening torque Nm (kgf.m, lb - ft) :
100 ~ 120 (10 ~ 12, 72.3 ~ 86.8)
3.Install the front stabilizer link (A) nut (B) to the strut assembly.
Tightening torque Nm (kgf.m, lb - ft) :
100 ~ 120 (10 ~ 12, 72.3 ~ 86.8)
4.Install the speed sensor (A) and wire (B) bolts.
Tightening torque Nm (kgf.m, lb - ft) :
7 ~ 11 (0.7 ~ 1.1, 5.1 ~ 8.0)

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Loosen the wheel nuts slightly. Raise the rear of the vehicle, and make sure it is securely supported.
2. Remove the rear wheel and tire (A) from rear hub (B).
Be careful not to damage the hub bolts (C) when removing the rear wheel and tire (A).
3. Remove the wheel speed sensor wire's bracket bolt (A) from the body and the connector.
4.Remove the wheel speed sensor wire's bracket bolt (A) and the parking brake wire's bracket bolt (B).
5.Remove the trailing arm (A) mounting nuts (B) from the knuckle.

5.Remove the wheel speed sensor wire's bracket bolt (A) and the parking brake wire's bracket bolt (B).
Tightening torque Nm (kgf.m, lb - ft) :
7 ~ 11 (0.7 ~ 1.1, 5.1 ~ 8.0)
6.Install the wheel speed sensor wire's bracket bolt (A) from the body and the connector.
Tightening torque Nm (kgf.m, lb - ft) :
7 ~ 11 (0.7 ~ 1.1, 5.1 ~ 8.0)
7.Install the wheel and the tire (A) to the rear hub (B).
Tightening torque Nm (kgf.m, lb - ft) :
90 ~ 110 (9 ~ 11, 65.1 ~ 79.5)