oil KIA CARNIVAL 2007 Owner's Manual

camshaft. Ensure that the pin will not be installed in the hole for oil feeding.
Tightening torque
66.7~78.5Nm(6.8~8.0kgf.m, 49.2~57.9lb - ft)
After tightening the CVVT bolts, rotate the CVVT assembly housing counterclockwise by hand to seat the lock
pin in the CVVT assembly in good position.
Fix the hexagonal part of the camshaft in a vice when tightening the CVVT bolts. Do not fix the CVVT housing
or sprocket in a vice.
4. Install the camshaft in the cylinder head assembly.
(1) Align the timing mark of the camshaft timinig chain.
LH camshaft chain timing mark
RH camshaft chain timing mark
Both timing marks should face upward in reassemby.
5. Install the timing chain tensioner.
(1) Insert the set pin by pressing the timing chain tensioner.
(2) Install the chain tensioner(A) in the cylinder head assembly.

7.Using the SST(09214- 21000), install the camshaft oil seal.
a.Befor installing, apply engine oil.
b. The camshaft cap surface should adhere to the cylinder head assembly.
c. Do not press an eccentric load.
8. Install the CKP sensor connector bracket(A).
9.Install the bank 1 timing belt rear cover(A).
10. Install the bank 2 timing belt rear cover(A).

The length of the bolt(B) is longer than that of the bolt(C).
11. Install the timing belt.(Refer to 'Timing system').
12. Check and adjust the valve clearance.
13. Install the cylinder head cover.
(1) Remove oil, dust or sealant on the upper surface of the cylinder before assembling cylinder head cover.
(2) Assemble the cylinder head cover in five minites after applying liquid gasket(LOCTITE 5900) on the camshaft
cap and packing part.
(3)Tighten the cylinder head cover bolts as following order(A).
Tightening torque
7.8~9.8Nm(0.8~1.0kgf.m, 5.8~7.2lb- ft)

(6)Connect the injection harness connector(A), the No.2 VIS(Variable Induction System) connector(B), the
No.1/No.2 OCV(Oil Control Valve) connectors(C,D) and the OTS(Oil Temperature Sensor) connector(E).
(7)Connect the injection connectors(A,B,C), the ground lines(D), the condensor connector(E) and the Ignition coil
connectors(F).
(8)Connect the bank 1 front/rear O2 sensor connectors(A).

(9)Connect the No.1/No.2 knock sensor connectors(A,B), the oil pressure switch connector(C), the ignition coil
harness(D) and the No.1 VIS(Variable Induction System) connector(E).
23. Install the fuel inlet hose(A) from the delivery pipe.
24.Install the upper radiator hose(A) and lower radiator hose(B).
25.Install the intake air hose and air cleaner assembly.
(1) Install the intake air hose and air cleaner assembly(C).

(5)Using SST(09222- 29000), remove the valve stem seal.
Do not reuse the removed valve stem seals.
3. Remove OCV(Oil Control Valve)(A).
INSPECTION
CYLINDER HEAD
1. Inspect for flatness.
Using a precision straight edge and feeler gauge, measure the surface contacting cylinder block and the manifolds
for warpage.
Flatness of cylinder head gasket surface
Standard : 0.03mm(0.0012in.) or less
Flatness of manifold gasket surface
Standard : 0.15mm(0.0059in.) or less
2.Inspect for cracks.

(4)Install the bearing caps with the tightening torque.
Do not turn the camshaft.
(5) Remove the bearing caps.
(6) Measure the plastigage at its widest point.
Bearing oil clearance
[Standard value]
Intake : 0.020 ~ 0.057mm (0.0008 ~ 0.0022in.)
Exhaust : 0.020 ~ 0.057mm (0.0008 ~ 0.0022in.)
If the oil clearance is greater than the maximum, replace the camshaft. If necessary, replace the cylinder head.
(7) Completely remove the plastigage.
(8) Remove the camshafts.
4. Inspect camshaft end play.
(1) Install the camshafts.
(2) Using a dial indicator, measure the end play while moving the camshaft back and forth.
Camshaft end play
[Standard value] : 0.05 ~ 0.15mm(0.0020 ~ 0.0059in.)

If the end play is greater than the maximum, replace the camshaft. If necessary, replace the cylinder head.
(3) Remove the camshafts.
CVVT ASSEMBLY
1.Inspect CVVT assembly.
(1) Fix the CVVT assembly with a vice. Ensure that the cam lobe and journal is not damaged.
(2) Check that the CVVT assembly will not turn.
It should not be turned.
(3) Apply vinyl tape to the retard hole except the one(A) indicated by the arrow in the illustration.
(4)Wind tape around the tip of the air gun and apply air of approx. 150kpa(1.5kgf/cm², 21psi) to the port of the
camshaft.
(Perform this in order to release the lock pin for the maximum delay angle locking.)
When the oil splashes, wipe it off with a shop rag.
(5) After the lock pin released, the CVVT assembly can turned in advanced direction.
If the air applied is leaked much, the lock pin can not be released.
(6) Except the position where the lock pin meets at the maximum delay angle, let the CVVT assembly turn back
and forth and check the movable range and that there is no resistance to movement.
Standard: Movable smoothly in the range about 60°
(7) Turn the CVVT assembly with your hand in retard direction and lock it at the maximum delay angle position.

REASSEMBLY
a.Thoroughly clean all parts to be assembled.
b. Before installing the parts, apply fresh engine oil to all sliding and rotating surfaces.
c. Replace oil seals with new ones.
1. Install valves.
(1) Using SST(09222- 22001), push in a new valve stem seal with applying engine oil.
a.Do not reuse old valve stem seals.
Incorrect installation of the seal could result in oil leakage past the valve guides.
b. Reassemble the valve stem seals
(2) After applying engine oil on the outer surface of each valve stem, insert the valve in the valve guide.
Install the valve, valve spring and spring retainer.
When installing valve springs, the side coated with enamel should face toward the valve spring retainer
(3) Using the SST(09222 - 3K000, 09222 - 3C300), compress the springs and install the retainer locks. After
installing the valves, ensure that the retainer locks are correctly in place before releasing the valve spring
compressor.

(4)Lightly tap the end of each valve stem two or three times with the wooden handle of a hammer to ensure
proper seating of the valve and retainer lock.
2. Install MLAs with engine oil applied on its surface.
Check that the MLA rotates smoothly by hand.
MLA should be reinstalled in its original position.
3. Install OCV(Oil Control Valve)(A).
Tightening torque
7.8 ~ 9.8Nm(0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb - ft)
a.To install OCV with gray colored connector into RH bank.
b. To install OCV with black colored connector into LH bank.