window KIA CARNIVAL 2007 Owner's Manual

18Burglar Alarm horn ON/OFFContiuously ON with 60
cycles per minute, Duty:50%
RAM ACTUATOR LIST No. Description ValueControl
1 Room Lamp LS ON/OFFContinuously ON
2 Room Lamp LS Door ON/OFFContinuously ON
3 Luggage Lamp LS ON/OFFContinuously ON
4 LQG Motor Close ON/OFF3 sec ON then OFF (once)
5 LQG Motor Open ON/OFF3 sec ON then OFF (once)
6 RQG Motor Close ON/OFF3 sec ON then OFF (once)
7 RQG Motor Open ON/OFF3 sec ON then OFF (once)
8 RSD Power Window Up ON/OFF3 sec ON then OFF (once)
9 RSD Power Window Down ON/OFF3 sec ON then OFF (once)
10 LSD Power Window Up ON/OFF3 sec ON then OFF (once)
11 LSD Power Window Down ON/OFF3 sec ON then OFF (once)
12 LH PSD Open Close Signal ON/OFF0.5 sec ON then OFF
(once)
13 RH PSD Open Close Signal ON/OFF0.5 sec ON then OFF
(once)
14 PTG Open Close Signal ON/OFF0.5 sec ON then OFF
(once)
15 PSD PTG On Off Signal ON/OFFContinuously ON
16 Park Signal ON/OFFContinuously ON
17 Start Signal ON/OFFContinuously ON
18 Rear Defog ON/OFFContinuously ON
19 Rear Fog Lamps ON/OFFContinuously ON
20 Right Turn Signal Lamp ON/OFFContiuously ON with (80 +/ -
5) cycles per minute, Duty: 50%
21 Left Turn Signal Lamp ON/OFFContiuously ON with (80 +/ -
5) cycles per minute, Duty: 50%
22 Back Up Lamp Back Up Warning System Unit ON/OFFContinuously ON
23 Left/Right Tail Licence Side Marker ON/OFFContinuously ON
24 Door Lock ON/OFF0.5 sec ON then OFF
(once)
25 Door Unlock ON/OFF0.5 sec ON then OFF
(once)
26 Rear Wiper Motor ON/OFF5 sec ON then OFF (once)
27 Rear Blower Switch
& Rear Monitor
illumination ON/OFF
Continuously ON
0.5 sec ON then OFF

28Fuel Filler Door Solenoid ON/OFF0.5 sec ON then OFF
(once)
29 Map Lamp LS ON/OFFContinuously ON
DDM ACTUATOR LIST No. Description ValueControl
1 Door Courtesy Lamp ON/OFFContinuously ON
2 Door Lock Out ON/OFF0.5 sec ON then OFF
(once)
3 Door Unlock Out ON/OFF0.5 sec ON then OFF
(once)
4 OSRVM Up ON/OFF3 sec ON then OFF (once)
5 OSRVM Down ON/OFF3 sec ON then OFF (once)
6 OSRVM Left ON/OFF3 sec ON then OFF (once)
7 OSRVM Right ON/OFF3 sec ON then OFF (once)
8 OSRVM Defog ON/OFFContinuously ON
9 Folding Motor Power Feed ON/OFFContinuously ON
10 Safety Power Window Auto Up Out ON/OFF0.2 sec ON then OFF
(once)
11 Safety Power Window Up Out ON/OFF3 sec ON then OFF (once)
12 Safety Power Window Auto Down Out ON/OFF0.2 sec ON then OFF
(once)
13 Safety Power Window Down Out ON/OFF3 sec ON then OFF (once)
14 Power Window up Out ON/OFF3 sec ON then OFF (once)
15 Power Window Down Out ON/OFF3 sec ON then OFF (once)
16 Illumination Out ON/OFFContinuously ON
ADM ACTUATOR LIST No. Description ValueControl
1 Door Courtesy Lamp ON/OFFContinuously ON
2 Door Lock Out ON/OFF0.5 sec ON then OFF
(once)
3 Door Unlock Out ON/OFF0.5 sec ON then OFF
(once)
4 OSRVM Up ON/OFF3 sec ON then OFF (once)
5 OSRVM Down ON/OFF3 sec ON then OFF (once)
6 OSRVM Left ON/OFF3 sec ON then OFF (once)
7 OSRVM Right ON/OFF3 sec ON then OFF (once)
8 OSRVM Defog ON/OFFContinuously ON
9 Power Window up Out ON/OFF3 sec ON then OFF (once)
10 Power Window Down Out ON/OFF3 sec ON then OFF (once)
11 Illumination Out ON/OFFContinuously ON
IMS ACTUATOR LIST

2.When the power ON/OFF button (PWR) (B) is ON, the power sliding door and power tailgate can be opened and
closed automatically by using trim switch.
3. When the sliding door window is open (more than 3 in/80 mm), the power sliding door will not power open fully but
will open to the 3/4 position and the chime will sound 3 times.
4. General rules for chime functions
a. Chime shall operate when a power operation cannot be performed as requested except handle pull : 1 Time
(Duration 0.5 second on)
b. Chime shall operate when an obstacle has been detected : 3 Time (0.5 sec on, 0.5 sec off)
c. Chime shall operate if PSD has not reached primary latch position after a power cinch cycle : 3 Time (0.5 sec
on, 0.5 sec off)
Do not leave the power sliding door at half- opened position. Close the window and then open the door fully.
Half - opened door is held and then released after 10 minutes. The chime sounds 3 times to indicate the door
is released. If the vehicle is stopped on a downward slope, it may move and cause an injury.
POWER SLIDING DOOR OPERATING CONDITION
1.The sliding door will not power open when vehicle is moving above 3 mph (5 km/h) or the gearshift lever is not in
P (Park) for automatic transaxle.
2. The power sliding door will not open with the transmitter or the main control button when all power sliding doors
are locked and closed.
3. The power sliding door will detect the resistance, then stop movement or move to the full open position to allow the
object to be cleared.
4. The left sliding door cannot be opened when the fuel filler lid is open.
5. If the automatic stop and reversal feature operates continuously more than twice during one opening or closing
operation, the power sliding door may stop at that position. At this time, close the doors manually and operate the
door automatically again.
6. The power sliding door can be opened by pulling the outside door handle while the door is unlocked and child
safety lock is engaged.
a.If the fuel filler lid is opened when the left sliding door is not closed completely, the door may be opened.
Close the left sliding door before refueling to prevent possible damage to the door or the fuel filler lid.
b. Sudden starting or accelerating the vehicle while the door is closing could cause it to open the door and
result in a serious injury or damage to cargo.
c. The PSDM will go to a sleep mode and power operation will be disabled if the sliding door is left open
longer than 6 hours. Manually close the sliding door to the latched position to reset the PSDM. Power
operation will be restored.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal.
2. Remove the front door trim panel. (Refer to the Body group - front door)
3. Remove the power window main switch mounting screws (3EA) (A) after disconnecting the switch connector
(12pin) from the switch.
4.Remove the switch from the front door trim panel.
5. Installation is the reverse of removal.
INSPECTION
1.Disconnect the 12P connector from the switch.
2.Check for continuity between the terminals in each switch position according to the table.

Power Windows

Power Window Motor

2007 > 2.7L V6 GASOLINE >
OPERATION
FUNCTION OF SAFETY POWER WINDOW
When driver door power window auto - up switch is operated, safety function is activated. 1. Safety function condition
When the system detects a force of 100N during the window rising, window is reversed.
2. Length of window reversing (except when holding the auto - up switch)
a. When detect the jamming within 4mm ~ 300mm from top of the door.
→ Window is reversed until 350mm from top of the door.
b.When detect the jamming over the 300mm from top of the door.
→ Window is reversed until 50mm from jamming position.
3.Length of window reversing (holding the auto - up switch)
a. When detect the jamming during holding the auto - up switch.
→ Window is reversed until 20mm from jamming position.
4.Safety function is not available area
Safety function is not available within 4mm from top of the door.

INITIALIZING METHOD OF THE SAFETY POWER WINDOW
1.Initializing of Battery Connection
(1) Power window operation before initializing
a. Manual- Up/Down function is available
b. Auto- Up function is not available
(When holding the auto - up/down switch, window is operated as a manual- up/down.)
(2) Initializing method
Close the window in window open position, and holding the switch in window full close position more than 1
second.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
FRONT POWER WINDOW MOTOR
1. Remove ( - ) negative battery terminal.
2. Remove the front door trim panel. (Refer to the Body group - front door)
3. Remove the window motor (B) after disconnecting the motor connector (A) and mounting nuts.
4.Installation is the reverse of removal.
SLIDING POWER WINDOW MOTOR
1.Remove ( - ) negative battery terminal.
2. Remove the sliding door trim panel. (Refer to the Body group - rear door)
3. Remove the door trim seal and glass.
4. Remove the door regulator.
5. Remove the power window motor (A) after disconnecting the motor connector and power window motor mounting
nuts.
6.Installation is the reverse of removal.
QUARTER GLASS MOTOR
1.Remove ( - ) negative battery terminal.
2. Remove the D pillar trim panel (A). (Refer to the Body group - interior trim)

3.Remove the quarter glass motor (B) after disconnecting the motor connector (A) and quarter glass motor mounting
bolts and screws.
4.Installation is the reverse of removal.
INSPECTION
FRONT POWER WINDOW MOTOR INSPECTION
1. Remove ( - ) negative battery terminal.
2. Remove the rear door trim panel. (Refer to the Body group - front door)
3. Disconnect the motor connector from the motor.
4.Connect the motor terminals directly to battery voltage (12V) and check that the motor operates smoothly. Next,
reverse the polarity and check that the motor operates smoothly in the reverse direction. If the operation is
abnormal, replace the motor.
SLIDING POWER WINDOW MOTOR INSPECTION