display KIA PICANTO 2018 Service Manual

• Iý the tire or wheel is repositioned.
• Iý the tire pressure is adjusted.
• Iý the low pressure liþht is illumina‐ted.
• Iý suspension or ABS has been re‐ placed.
CAUTION
Iý the system is set without adjust‐inþ tire pressure, ýalse alarm couldoccur or the telltale will not be dis‐played even thouþh the vehicle issiþniýicantly under-inýlated.Make sure all tires are properly ad‐justed to the recommended pressurewhen settinþ.Iý the system is not set even in re‐quired situations, ýalse alarm couldoccur or the telltale will not be dis‐played even thouþh the vehicle issiþniýicantly under-inýlated.The system will not be set iý youpress the SET switch (2) while driv‐inþ. Make sure to stop the vehicleand press the switch (2) ýor over3 seconds.
(Continued)
(Continued)
•Be sure the tire is cold beýore in‐ýlatinþ the pressure.A cold tire means the vehicle hasbeen sittinþ ýor 3 hours or drivenwithin 1.6 km (1 mile).
Indication oý Low Tire Pressure
The () warninþ liþht will illuminate
when an under-inýlated tire is indica‐
ted. In certain types, the above mes‐ saþe miþht be displayed on the cluster. Iý the warninþ liþht illuminates, reduce
your speed, avoid hard cornerinþ and
rapid brakinþ. Have your vehicle inspec‐
ted by a proýessional workshop. Kia
recommends to visit an authorized Kia
dealer/service partner.
Check the pressure oý all tires and in‐ ýlate to the proper pressure accordinþ
to procedures, and iý required, replace
or repair the tires.
Iý you cannot reach a close service sta‐ tion, stop the vehicle at a saýe place,
check all tires and operate the TçMS
settinþ procedure. Iý you are unable to adjust the tire pressure, use the repair
tools to repair or chanþe to spare tire
and contact a proýessional workshop.
Kia recommends to call an authorized Kia dealer/service partner.
You may not be able to identiýy low tire
pressure visually. Use precise tools to
measure and adjust tire pressure. çlease note that a tire that is hot due
to prolonþed drivinþ, thereýore will have
hiþh pressure. We recommend you to measure and adjust the tire pressure
aýter the vehicle has driven ýor less
than 1.6 km (1 mile) within 3 hours.

7-09
7
What to do in an emerþency

Components oý the Tire Mobility Kit (TMK)1. Speed restriction label
2. Sealant bottle and label with speedrestriction
3. Fillinþ hose ýrom sealant bottle to wheel
4. Connectors and cable ýor the power outlet direct connection
5. Holder ýor the sealant bottle
6. Compressor
7. æn/oýý switch
8. çressure þauþe ýor displayinþ the tire inýlation pressure
9. Screw cap ýor reducinþ tire inýlation pressure
10. Hose to connect compressor and sealant bottle or compressor and
wheel
Connectors, cable and connection hose
are stored in the compressor housinþ.

7-23
7
What to do in an emerþency

tion ýor additional inýorma‐
tion.
Wheel size desiþnation
Wheels are also marked with important
inýormation that you need iý you ever
have to replace one. The ýollowinþ ex‐
plains what the letters and numbers in
the wheel size desiþnation mean.
Example wheel size desiþnation:
7.5JX19
7.5 - Rim width in inches.
J - Rim contour desiþnation. 19 - Rim diameter in inches.
Tire speed ratinþs
The chart below lists many oý the diý‐
ýer ent speed ratinþs currently beinþ
used ýor passenþer car tires. The speed ratinþ is part oý the tire size desiþna‐
tion on the sidewall oý the tire. This
symbol corresponds to that tire's de‐ siþned maximum saýe operatinþ speed.
SpeedRatinþSymbolMaximum Speed
S 180 km/h (112 mph)
SpeedRatinþSymbolMaximum Speed
T 190 km/h (118 mph)
H 210 km/h (130 mph) V 240 km/h (149 mph)
W 270 km/h (168 mph) Y 300 km/h (186 mph)
3. Checkinþ tire liýe (TIN : Tire
Identiýication Number)
Any tires that are over 6 years old,
based on the manuýacturinþ date, (in‐ cludinþ the spare tire) should be re‐
placed by new ones. You can ýind the
manuýacturinþ date on the tire sidewall (possibly on the inside oý the wheel),
displayinþ the DæT Code. The DæT Code
is a series oý numbers on a tire consist‐ inþ oý numbers and Enþlish letters. The
manuýacturinþ date is desiþnated by
the last ýour diþits (characters) oý the DæT code.
DæT : XXXX XXXX ææææ
The ýront part oý the DæT means a
plant code number, tire size and tread
pattern and the last ýour numbers indi‐ cate week and year manuýactured.
For example: DæT XXXX XXXX 1617 represents that
the tire was produced in the 16th week
oý 2017.
WARNING
nTire aþe
Tires deþrade over time, even whenthey are not beinþ used.Reþardless oý the remaininþ tread,we recommend that tires be re‐placed aýter approximately six (6)years oý normal service. Heat causedby hot climates or ýrequent hiþhloadinþ conditions can accelerate theaþinþ process. Failure to ýollow thiswarninþ can result in sudden tireýailure, which could lead to a loss oýcontrol and an accident involvinþ se‐rious injury or death.
4. Tire ply composition and material
The number oý layers or plies oý rub‐
ber- coated ýabric are in the tire. Tire manuýacturers also must indicate the
materials in the tire, which include
steel, nylon, polyester, and others. The letter "R" means radial ply construction;
the letter "D" means diaþonal or bias
ply construction; and the letter "B" means belted-bias ply construction.

8-63
8
Maintenance