engine Lancia Delta 2008 Owner handbook (in English)

GETTING TO KNOW YOUR CAR15
1
Diesel particulate filter clogged
(amber) (Multijet versions)
This warning light comes on when the ignition
key is turned to MAR, but it should go off after
a few seconds. The warning light comes on when the diesel
particulate filter is clogged and the driving conditions do
not allow the automatic activation of the regeneration cy-
cle.
To allow the regeneration cycle to take place, keep the car
running until the warning light turns off.
The display will show a dedicated message.
h
Fuel reserve (amber)
This warning light comes on when the ignition
key is turned to MAR, but it should go off af-
ter a few seconds. The warning light comes on
when about 5 to 7 litres of fuel are left in the tank.
The display will show a dedicated message.
IMPORTANT The warning light will blink to indicate a
system failure. Go to a Lancia Dealership to have the sys-
tem checked.
K
EOBD/injection system failure (amber)
Under normal conditions, the warning light
comes on when the ignition key is turned to
MAR, but should go off as soon as the engine is
started.
If the warning light remains on or comes on whilst driving,
this means that the injection system is not working prop-
erly; in particular, if the warning light comes on constantly,
this indicates a malfunction in the supply/ignition sys-
tem that could cause excessive exhaust emissions, a pos-
sible loss of performance, poor driveability and high fuel
consumption.
On certain versions a dedicated message is displayed. Un-
der these conditions, the vehicle can continue travelling at
moderate speed without demanding excessive effort from
the engine. Prolonged use of the car with the warning light
on may cause damage. Go to a Lancia Dealership as soon
as possible.
The warning light goes out after the fault is cleared, and
the indication is stored in the system.
Petrol engines only
If the warning light is flashing, this indicates that the cat-
alytic converter may be damaged.
If the light flashes, release the accelerator pedal to lower
the speed of the engine until the warning light stops flash-
ing; continue the journey at moderate speed, trying to avoid
driving conditions that may cause further flashing and con-
tact a Lancia Dealership as soon as possible.
U
Steering corrector not available
This warning light (or symbol on the display) comes on
when the steering corrector is not available. The display
will show a dedicated message.

16GETTING TO KNOW YOUR CAR
Go to a Lancia Dealership as soon as possi-
ble if warning light Ueither does not light up
when the key is turned to MAR or if while
travelling the warning light comes on either steady
or blinking (on some versions along with a message
on the display). The operation of the warning light
Umay be checked by the traffic police using spe-
cific devices. Follow the laws in force in the coun-
try where you are driving.
Advanced ESP system (amber)
This warning light comes on when the ignition
key is turned to MAR, but it should go off after
a few seconds. If the warning light does not go off
or stays on together with the LED on the ASR button when
travelling, contact a Lancia Dealership. On certain versions
a dedicated message is displayed. If the warning light
flashes when driving, this indicates that the Advanced ESP
system has cut in.
á
Hill holder system failure (amber)
The áwarning light turns on to indicate a Hill
holder system failure. In this case, contact a
Lancia Dealership as soon as possible. Alter-
natively, on some versions the *symbol is
lit up on the display.
The display will show a dedicated message.
á
*
Glow plug preheating
This warning light comes on when the key is
turned to MAR. It will go out as soon as the glow
plugs have reached a predetermined temperature.
Start the engine as soon as the warning light goes out.
IMPORTANT At high outdoor temperatures the warning
light stays on for an extremely short time.
m
To switch the warning light off, carry out the following
initialization procedure:
turn the ignition key to the ON position;
turn the steering wheel fully both clockwise and anti-
clockwise (to move from the position with the wheels
straight);
turn the ignition key to the OFF position and then turn
it back ON.
If the
áwarning light does not go out after a few
seconds, seek assistance from a Lancia Dealership.

GETTING TO KNOW YOUR CAR17
1
Water in diesel fuel filter (Multijet
versions) (amber)
This warning light comes on when the ignition
key is turned to MAR, but it should go off after
a few seconds. The warning light turns on when there is
water in the diesel fuel filter. The display will show a ded-
icated message.
c
The presence of water in the fuel system cir-
cuit may cause severe damage to the injection
system and irregular engine operation. If the
cwarning light comes on (together with a message
on the display on some versions), go to a Lancia
Dealership as soon as possible to have the system
bled. Water may have been introduced in the tank if
this appears immediately after refuelling: in this
case, stop the engine immediately and contact a
Lancia Dealership.
ABS system failure (amber)
This warning light comes on when the ignition
key is turned to MAR, but it should go off af-
ter a few seconds. The warning light lights up
when the system is either not working or not available.
Under these circumstances the braking system will work
as normal without the extra performance offered by the
ABS system.
Drive carefully to the nearest Lancia Dealership to have
the system checked.
The display will show a dedicated message.
>
Lancia Code system failure (amber)
This warning light (or symbol on the display),
when on constantly with the ignition key turned
to MAR, indicates a possible failure (see “Lancia
Code system” in chapter 1).
If the
Ywarning light (or symbol in the display) is blink-
ing, this means that the vehicle is not protected by the en-
gine inhibitor device (see “Lancia Code system” in chap-
ter 1).
Contact a Lancia Dealership to have all the keys stored.
Alarm failure (where provided)
A fault with the alarm system is signalled by this warn-
ing light (or symbol in the display) coming on. Contact a
Lancia Dealership as soon as possible.
The display will show a dedicated message.
Y
Glow plug heating failure
The warning light will blink in the event of a failure in the
glow plug preheating system. Go to a Lancia Dealership
as soon as possible.
The display will show a dedicated message.

GETTING TO KNOW YOUR CAR21
1
On some versions the display shows the turbine pressure
fig. 5 when the “engine info ” menu item is selected and
the key is turned to MAR.
fig. 4L0E1000g
fig. 5L0E0004mfig. 6L0E1001g
RECONFIGURABLE MULTIFUNCTIONAL
DISPLAY “STANDARD” SCREEN fig. 6
The standard screen shows the following information:
A. Time
B. Date
C. Sport driving mode indication (where provided)
D. Odometer (distance travelled in kilometres/miles)
E. Car status (e.g. doors open, ice on road, etc.)
F. Headlight alignment position (with dipped beam head-
lights on only).
G. Outside temperature

28GETTING TO KNOW YOUR CAR
First page (Display of information on the initial
screen) (where provided)
This function allows you to choose the information you
would like to see on the main screen. You can choose to
display the date or the turbo charger turbocharging pres-
sure.
Proceed as follows:
– briefly press SET: “Initial page” will appear on the dis-
play;
– briefly press SET once again to show the display options:
“Date” and “Engine info”;
– press + or – to select the information you wish to see
on the main page of the display;
– briefly press SET to go back to the menu screen or hold
the button down to go back to the standard screen with-
out storing the new settings.
When the key is turned to MAR and the initial check stage
is over, the display will show the information selected via
the “initial page” menu function.See radio (Repeat audio information)
With this function the display repeats information rele-
vant to the sound system.
– Radio: tuned radio station frequency or RDS message,
automatic tuning activation or AutoSTore;
– audio CD, MP3 CD: track number;
– CD Changer: CD number and track number.
To activate (On) or to deactivate (Off) sound system in-
fo displaying proceed as follows:
– press SET briefly: (On) or (Off) will flash on the display
(according to previous setting);
– press
Õor Ôto change the setting;
– briefly press SET to go back to the menu screen or hold
the button down to go back to the standard screen with-
out storing the new settings.
Autoclose (Automatic door lock operation with car
running)
When activated (On), this function automatically locks
the doors when the car speed exceeds 20 km/h.
Proceed as follows to switch this function on or off:
– briefly press SET to display a submenu;
– briefly press SET: (On) or (Off) will flash on the display
(according to previous setting);
– press
Õor Ôto change the setting;

34GETTING TO KNOW YOUR CAR
TRIP COMPUTER
GENERAL FEATURES
The Trip computer is used to display information on car
operation when the key is turned to MAR. This function
allows you to define two separate trips called “Trip A” and
“Trip B” for monitoring the car’s complete mission (trip)
in a mutually independent manner.
Both functions can be reset (reset - start of new mission).
Trip A can be used to display figures relating to:
– Range
– Distance travelled
– Average fuel consumption
– Instantaneous fuel consumption
– Average speed
– Travel time (driving time).
– Trip A Reset
The Trip B function is used to display information relat-
ing to:
– Distance travelled B
– Average fuel consumption B
– Average speed B
– Travel time B (driving time).
– Trip B ResetNote “Trip B” functions may be excluded (see “Enabling
Trip B”). “Range” and “Instantaneous fuel consumption”
parameters cannot be reset.
Values displayed
Range
Approximately indicates the distance the vehicle can trav-
el with the present amount of fuel in the tank. The message
“- - - -” will appear on the display in the following cases:
– range value lower than 50 km (or 30 mi)
– car left parked with the engine running for a long time.
IMPORTANT Changes in the range value can be affect-
ed by many factors: driving style (see “Driving style” in
“Starting up and driving”), type of route (motorway, ur-
ban cycle, mountain roads, etc…), conditions of use of the
car (load, tyre pressure, etc.). The above notes should
therefore be taken into consideration when planning a trip.
Distance travelled
This indicates the approximate distance covered from the
start of the new mission.

GETTING TO KNOW YOUR CAR35
1
Average fuel consumption
This value shows the approximate average fuel con-
sumption from the start of the new mission.
Instantaneous fuel consumption
This indicates any change in fuel consumption. The value is
constantly updated. The message “- - - -” will appear on the
display if the car is parked with the engine running.
Average speed
This value shows the average speed of the car based on
the overall time elapsed since the start of the new mission.
Travel time
This value shows the time elapsed since the start of the
new mission.
Trip Reset
This resets the Trip computer settingsTRIP button fig. 8
The TRIP button is located on the right-hand lever. With
the ignition key turned to MAR, this button allows you
to view the previously described parameters and also ze-
ro them to begin a new mission:
– short press to display the different values;
– long press to reset and then start a new mission.
fig. 8L0E0007m

GETTING TO KNOW YOUR CAR37
1
THE LANCIA CODE SYSTEM
This is an electrical engine locking system which increases
protection against an attempted theft of the car. It is auto-
matically activated when the ignition key is extracted.
Each key contains an electronic device which modulates
the signal emitted during ignition by an antenna built in-
to the ignition device. This signal is the ‘password’ which
changes at each ignition and which the control unit uses
to recognise the key and allow ignition.
OPERATION
Each time the car is started by turning the ignition key
to MAR, the Lancia CODE system control unit sends an
acknowledgement code to the engine control unit to de-
activate the inhibitor.
The code is sent only if the control unit of the Lancia
CODE system has acknowledged the code received from
the key.
Each time the ignition key is turned to STOP, the Lancia
CODE system deactivates the functions of the electronic
engine control unit.
If the code is not recognised correctly during ignition, the
Ywarning light (or symbol in the display) comes on.In this case turn the key to STOP and then to MAR; if
the lock persists try again with the spare set of keys. Con-
tact a Lancia Dealership if you still cannot start the en-
gine.
IMPORTANT Each key has its own code which must be
stored by the system control unit. To have new keys mem-
orised (up to a maximum number of eight keys), contact
a Lancia Dealership and be ready to present all the keys
you have at present, the CODE card, a personal identity
document and the car ownership documents. The codes
of any keys not presented during the memorising proce-
dure will be deleted. This is to prevent lost or stolen keys
from starting the engine.
Ywarning light (or symbol in the display) lit up
during driving
If the Ywarning light (or symbol in the display)
comes on, this means that the system is running a self-
diagnosis test (caused, for example, by a voltage drop).
If the Ywarning light (or symbol in the display) remains
on, contact a Lancia dealership.
The electronic components inside the key may
be damaged if the key is submitted to sharp
knocks.

42GETTING TO KNOW YOUR CAR
IMPORTANT The engine inhibitor function is guaranteed
by the Lancia CODE, which is automatically activated
when the ignition key is extracted from the starter de-
vice.
SWITCHING ON THE ALARM
With the doors and bonnet closed and the ignition key
either turned to STOP or removed, point the key with the
remote control towards the vehicle and press and release
button
Á.
Excluding some versions for specific markets, the system
produces an acoustic warning (beep) and enables door
locking.
Before the alarm is enabled, a self-diagnosis test is run:
if a fault is detected, the system emits another sound warn-
ing and a message is shown on the display, (see “Instru-
ment panel warning lights”).
In this case switch off the alarm by pressing
Ë, check that
all the doors, bonnet and tailgate are closed correctly; then
switch the alarm back on by pressing
Á.
If a door or the bonnet is not correctly closed, it will be ex-
cluded from the testing by the alarm system.
If the alarm produces an acoustic signal even when the
doors, bonnet and tailgate are correctly closed, a failure
has occurred in system operation. Contact a Lancia Deal-
ership.IMPORTANT Centrally locking the doors using the met-
al insert on the key does not activate the alarm.
IMPORTANT Originally, the alarm is configured in com-
pliance with the regulations existing in the different coun-
tries.
SWITCHING OFF THE ALARM
Press button
Ëon the key with the remote control.
The following operations are performed (excluding some
versions for specific markets):
the direction indicators flash twice;
two brief acoustic signals are emitted (“BEEP”);
the doors are unlocked.
IMPORTANT If the central door locking system is re-
leased using the metal insert of the key, the alarm is not
disabled.

44GETTING TO KNOW YOUR CAR
IGNITION SWITCH
The key can be turned to 3 different positions fig. 15:
STOP: the engine is off, the key can be extracted, the
steering is locked. Some electrical devices (e.g. car ra-
dio, central door locking system, etc.) are enabled
MAR: driving position. All electrical devices are en-
abled
AVV: engine start-up.
The ignition switch is fitted with an electronic safety sys-
tem that requires the ignition key to be turned back to
STOP if the engine will not start, before the starting op-
eration can be repeated.STEERING COLUMN LOCK
Engagement
When the key is at STOP, remove the key and turn the
steering wheel until it locks.
Disengagement
Move the steering wheel slightly as you turn the ignition
key to MAR.
IMPORTANT In some parking conditions (e.g.: wheels
turned) the effort required to move the steering wheel and
disengage the steering lock may be increased.
fig. 15L0E0107m
Never extract the key while the vehicle is
moving. The steering wheel would lock as
soon as the steering wheel is turned. This al-
so applies to when the car is towed. Under no cir-
cumstances should after-market operations be car-
ried out involving steering system or steering col-
umn modifications (e.g.: installation of anti-theft
device). This could negatively affect performance
and safety, invalidate the warranty and also re-
sult in vehicle non-compliance with type-approval
requirements.