high beam Lancia Delta 2008 Owner handbook (in English)
[x] Cancel search | Manufacturer: LANCIA, Model Year: 2008, Model line: Delta, Model: Lancia Delta 2008Pages: 258, PDF Size: 4.93 MB
Page 62 of 258
GETTING TO KNOW YOUR CAR61
1
Deactivation
When the lights are switched off by the sensor, the dipped
beam headlights and side lights are switched off and the
daylight lights are switched on (if activated).
The sensor cannot detect the presence of fog: switch the
lights on manually in this case.
FRONT FOG LIGHTS WITH CORNERING LIGHTS
FUNCTION
When travelling at a speed of less than 40 km/h with the
dipped beam headlights on, when the steering wheel is
turned at a wide angle or the direction indicators are lit
up, a light (built into the front fog lights) will be activat-
ed on the side of the turn to increase night time visibility.
This function can be switched on/off using the display
menus (see “Display” section in this chapter). AUTOMATIC HEADLIGHT SENSOR
(dusk sensor) fig. 27 (where provided)
This sensor detects changes in external light levels ac-
cording to the sensitivity of the setting: the higher the sen-
sitivity, the lower the amount of external light needed to
switch the lights on. The sensitivity of the dusk sensor may
be adjusted, using the “Set-up menu” on the instrument
panel.
Activation
Turn the selector wheel to AUTO: in this way the external
lighting will switch on automatically according to the out-
side light level.
The headlights can only be flashed with the sensor on.The daytime lights are an alternative to the
dipped beam headlights for driving during
the daytime. They are compliant in countries
where is it obligatory to have lights on during the
day and permitted in those where it is not obliga-
tory Daytime lights cannot replace dipped beam
headlights when driving at night or through tunnels.
The use of daytime lights is governed by the High-
way Code of the country you are in. Keep to the
rules.
Page 101 of 258
100GETTING TO KNOW YOUR CAR
HEADLIGHTS
BEAM DIRECTION
The correct orientation of the headlights is important for
the comfort and safety of not only the driver but all road
users. It is also a specific rule of the highway code.
The headlights must be correctly aligned to ensure the best
visibility conditions for all drivers.
Contact a Lancia Dealership to have the headlights prop-
erly adjusted.
Check beam alignment every time the load or its distrib-
ution changes.
BEAM ADJUSTMENT fig. 67
The car is fitted with an electric headlight alignment sys-
tem. This system is operational with the ignition key to
MAR and the dipped beam headlights on.
The car will tilt backwards when it is loaded, raising the
light beam.
In this case, it is necessary to adjust the beams using but-
tons A and B.
The display provides a visual indication of the position
during adjustment.Correct position depending on load
Position 0 - one or two passengers in the front seats.
Position 1 - five passengers.
Position 2 - five passengers + load in the boot.
Position 3 - driver + maximum permitted load in the lug-
gage compartment.
FRONT FOG LIGHT ALIGNMENT
(where provided)
Contact a Lancia Dealership to have the front fog lights
checked and properly adjusted.
fig. 67L0E0054m
Page 102 of 258
GETTING TO KNOW YOUR CAR101
1
HEADLIGHT ALIGNMENT ADJUSTMENT
ABROAD
The factory adjustment of the dipped beam headlights de-
pends on the country where the car is purchased. When
you travel in countries with a different driving direction,
it is necessary to cover certain areas of the headlight ac-
cording to the provisions of the Highway Code of the coun-
try you are travelling in to avoid blinding the drivers trav-
elling in the opposite direction.
ADAPTIVE LIGHTS (AFS - Adaptive Xenon Light)
This is a system linked to the Xenon headlights, which
continuously and automatically adjusts the main light
beam and adapts it to the driving conditions when cor-
nering. The system directs the light beam to improve the
illumination of the road, taking into account the vehicle
speed, the cornering angle and the speed at which the
steering wheel is turned.Activating/deactivating the system fig. 68
The adaptive lights are activated automatically when the
vehicle is started. In this situation the LED (amber) on
button A will remain off.
Press button A to deactivate the adaptive lights (if acti-
vated); the LED on button A will light up. To reactivate
the adaptive lights: press button A once again (LED on
button is off).
In the event of a system failure, an indication is provided
on the instrument panel by the flashing of warning light
for the symbol.
fappearing on the display along with
a dedicated message (where provided).
fig. 68L0E0055m
Page 180 of 258
IN AN EMERGENCY179
4
With gas discharge bulbs (Xenon)
(where provided)
MAIN BEAM HEADLIGHTS
With incandescent bulbs
To change the bulb, proceed as follows:
remove the protective cover A-fig. 15;
release the bulb holder clip A-fig. 17;
disconnect the electrical connector B;
remove the bulb C and replace it;
fit the new bulb, ensuring that the outline of the met-
al part coincides with the grooves on the curve of the
headlight. Then reconnect the electrical connector B
and reattach the bulb holding clip A;
refit the protective cover B-fig. 15.
fig. 17L0E0156m
Due to the high power supply voltage, gas
discharge bulbs (Xenon) should only be re-
placed by specialised personnel: risk of death!
Contact a Lancia Dealership.
With gas discharge bulbs (Xenon)
(where provided)
Due to the high power supply voltage, gas
discharge bulbs (Xenon) should only be re-
placed by specialised personnel: risk of death!
Contact a Lancia Dealership.