clutch Lancia Delta 2015 Owner handbook (in English)

74KNOWING YOUR CAR
When travelling downhill with the device engaged, the ve-
hicle speed may slightly exceed the pres et one.
The engagement of the device is s ignalled by the Üwarn-
ing light coming on in the in strument panel (together with
a message shown on the di splay ) (see “Ins trument panel
warning light s” paragraph).
S TORING THE C AR SPEED
Proceed as follows:
❍ turn the ring nut A - fig. 36 to ON and press the ac-
celerator pedal until the vehicle reaches the desired
s peed;
❍ turn the ring nut to (+) for at lea st three s econds, then
relea se it. The vehicle speed is now memoris ed and you
can therefore releas e the accelerator pedal.
If needed (when overtaking for in stance), you can accel-
erate simply by pre ssing the accelerator pedal; when you
releas e the pedal, the car will r
eturn to the speed memo-
ris ed previous ly .
RES TORING THE MEMORIS ED SPEED
If the device has been switched off, for example by de-
pressing the brake or clutch pedal, the memori sed speed
can be res tored as follows:
❍ accelerate graduall y until reaching a s peed approach-
ing the memori sed speed; ❍
engage the gear selected at the time of s peed memo-
ris ing (fourth, fifth or sixth gear);
❍ press button C - fig. 36.
INC REAS ING THE MEMORIS ED SPEED
This can be done in two wa ys:
❍ by pressing the accelerator and then memori sing the
new speed reached;
or
❍ by temporaril y turning ring nut B - fig. 36 to (+).
Each movement of the selector wheel will corres pond to
a slight incr
ease in s peed (about 1 km/h), while keeping
the selector wheel turned will corre spond to a continu-
ous speed increas e.
REDUC ING THE MEMORIS ED SPEED
This can be done in two wa ys:
❍ by dis engaging the device and then memoris ing the
new speed;
or
❍ by keeping ring nut B - fig. 36 turned to (–) until the
new speed is reached; it will then be memori sed auto-
matically .
Each movement of the ring nut will corre spond to a re-
duction in s peed of about 1 km/h, while keeping the ring
nut turned will corres pond to a continuous reduction in
s peed.
001-154 Delta GB 1ed 03/03/14 10.00 Pagina 74

KNOWING YOUR CAR75
1
DEACTIVATING THE DEVIC E
Turn the ring nut A - fig. 36 to OFF or turn the ignition
key to S TOP. The device is automatically turned off in one
of the following ca se s:
❍ when the brake or clutch pedal i s pressed;
❍ if the AS R or Advanced E SP system cuts in (for ver-
s ions /markets where provided);
While travelling with the device engaged, do
not place the gear lever in neutral.
In case of malfunction or if the device is faulty,
turn the control A - fig. 36 to OFF and con-
tact a Lancia Dealership, after checking that
the protective fuse has not blown.
ROOF LIGHTS
FRONT ROOF LIGHT WITH SPOT LIGHTS fig. 37
S witch A is used to s witch on/off roof light s.
With the s witch A in the middle po sition, the lights C and
D go on/off when front door s are opened/clo sed.
Wi t h switch A pressed to the left, the lights C and D are
always off. With s witch A pressed to the right, the lights
C and D are always on.
Lights switch on/off progre ssively.
S witch B controls the spot light function; when the roof
light is off, it s witches on individuall y:
❍ the light C when pre ssed to the left;
❍ the light D when pre ssed to the right.
fig. 37L0E0024m
001-154 Delta GB 1ed 03/03/14 10.00 Pagina 75

118KNOWING YOUR CAR
Fault indications
System failure is indicated by the
áwarning light light-
ing up in the in strument panel together with a dedicated
message appearing in the reconfigurable multifunction di s-
play ; see “Ins trument panel warning light s” chapter.
IMPORTANT The Hill Holder system is not a parking
brake; therefore, never leave the vehicle without having
engaged the handbrake, turned the engine off engaged the
firs t gear.
The Advanced ESP system continues to op-
erate if the space-saver wheel is fitted. Al-
ways remember that the space-saver wheel,
being smaller than the original wheel provides less
grip.
For the correct operation of the Advanced ESP and
ASR systems, the tyres must absolutely be the same
make and type on all wheels, in perfect conditions
and, above all, of the type, make and size speci-
fied.
HILL HOLDER S YSTEM
This is an integral part of the Advanced E SP system and
automaticall y cuts in in the following condition s:
❍ uphill: car at a s tandstill on a road with a gradient
higher than 5%, engine running, clutch and brake ped-
al pressed, gearbox in neutral or engaged gear other
than revers e.
❍ downhill: car at a stands till on a road with a gradient
higher than 5%, engine running, clutch and brake ped-
al pressed and revers e gear engaged.
During take off the Advanced E SP system control unit
maintains the braking pressure at the wheel s until the en-
gine torque required for departure i s reached or for a max-
imum of 2 seconds , allowing your right foot to be moved
eas ily from the brake pedal to the accelerator.
When two s econds have elaps ed, without starting, the sys-
tem is automaticall y deactivated, graduall y releas ing the
braking pressure. During thi s releas e stage it is possible to
hear a ty pical mechanical brake r

elea se nois e, indicating
the imminent move of the car.
001-154 Delta GB 1ed 03/03/14 10.00 Pagina 118

136KNOWING YOUR CAR
IMPORTANT The SEARCH stage in the system logic is
deactivated after about 10 min s if a s uitable parking s pace
i s not identified.
❍ Identification: if the system identifies a free parking
s pace that is a suitable size for the vehicle, it s ignals its
pres ence and indicates the actions required for starting the
manoeuvre.
❍ Manoeuvre : the driver is asked to engage rever se gear
and releas e the steering wheel and manage the accelera-
tor, brake and clutch (in ca se of manual gearbox) or ac-
celerator and brake (in ca se of automatic tran smission).
During the rever se parking manoeuvre, the system man-
ages the s teering wheel automaticall y.
It sugges ts that the manoeuvre be concluded in revers e
gear (if the condition s permit) when the continuou s s ound
of the buzzer for the rear s ensors is hear
d.
IMPORTANT The MANOEUVRE stage in the system log-
ic is deactivated after about 3 min s if the parking ma-
noeuvre ha s not been completed. ❍
Manoeuvre end: if the parking s pace is s ufficient, the
parking manoeuvre i s completed by the system in a s in-
gle movement; the further intervention of the driver i s not
required to po sition the vehicle. If further corrective ma-
noeuvres are required, the system gives back control to the
driver who mus t complete parking manuall y.
IMPORTANT Steering will be realigned after rever sing
when revers e gear is disengaged. The driver mus t com-
plete the manoeuvre manuall y.
The operation of the parking assistance is
based on different components:
❍ front and rear parking sensors;
❍ side sensors;
❍ steering;
❍ wheels and braking system;
❍ instrument panel.
It is necessary to bear in mind that a malfunction
in one of these systems could compromise the op-
eration of the Magic Parking system.
001-154 Delta GB 1ed 03/03/14 10.00 Pagina 136

KNOWING YOUR CAR139
1
Identifying a parking space fig. 81
If the system identifies a suitable parking s pace between
two stationary vehicles or between other obs tacles (e.g. ob-
jects with an extens ive side surface such as vehicles , box-
e s, etc.) it will indicate that it ha s found a s pace and that
parking is possible. If the po sition reached is already s uit-
able at the beginning of the manoeuvre, the system will ad-
vis e the driver to engage rever se gear, otherwis e it will re-
ques t moving further forward. On the reques
t to engage revers e gear the driver s hould stop
the vehicle and engage rever se in order to confirm the wi sh
to start the manoeuvre; if the driver continue s driving, af-
ter about 10 metres the system will no longer cons ider the
parking space identified and will start the s ear

ch for new
s uitable space.
Manoeuvre
The driver will have control over the movement s of the ve-
hicle us ing the accelerator, brake and clutch (onl y on ver-
s ions with manual gearbox) whil st the system will auto-
matically manage the s teering to enter the parking s pace
identified in the be st possible wa y.
During the manoeuvre it will be po ssible to take advantage
of the information coming from the parking s ensors (when
rever sing it i s advi sable to reach the area where the rear
s ens ors provide a continuous tone signal), but it i s always
advis able to keep an ey e on the surrounding area.
The vehicle can be s topped during the manoeuvre and,
whils t remaining s tationary, reverse gear can temporarily
be relea sed (for example, to allow a pedes trian to go by in
the area of the manoeuvre).
The speed should be less than about 7 km/h during the
manoeuvr

e, otherwis e the parking manoeuvre will be in-
terrupted.
fig. 81L0E1016g
001-154 Delta GB 1ed 03/03/14 10.00 Pagina 139

142KNOWING YOUR CAR
SY STEM MESSAGES ON THE INSTRUMENT PANEL
The Magic Parking system is
searching for a s uitable parking
s pace.
The Magic Parking system is
searching for a s uitable parking
s pace.
The Magic Parking system is
searching for a s uitable parking
s pace.
A suitable parking s pace has
been identified and the po sition
i s correct for starting the parking
manoeuvre. It is necessary to
s top and engage rever se gear.
Release
reverse gearWhen the Magic Parking activation
button is pressed, revers e gear must be
releas ed for the system to be s witched
on.
Do not touch the steering wheel!The manoeuvre i s about to begin, the
driver i s invited to let go of the s teer-
ing wheel.
Do not touch the steering wheel!
C arry out the
manoeuvreThe manoeuvre ha s s tarted, the driver
can accelerate and relea se the clutch
(in the cas e of a manual gearbox) to
enter the parking s pace; the Magic
Parking system will manage the steer-
ing automaticall y.
S peed
too hig hThe speed of the vehicle is about to ex-
ceed the maximum speed permitted by
the system (the message will be di s-
play ed at about 25 km/h for the search
s tage), if the driver increa se s the s peed
further, the system will automaticall y
be deactivated.
IMPORTANT Some messag es displayed are accompanied b y acoustic warnin gs.
001-154 Delta GB 1ed 03/03/14 10.00 Pagina 142

STARTING AND DRIVING185
3
Proceed as follows:
❍engage the handbrake;
❍ put the gear lever into neutral;
❍ turn the ignition key to MAR: the
mandYwarn-
ing lights on the instrument panel will turn on;
❍ wait for the warning lights
Yandmto turn off. The
hotter the engine is, the quicker this will happen;
❍ fully depress the clutch pedal without operating the ac-
celerator;
❍ turn the ignition key to AVV as soon as the
mwarn-
ing light goes out. Waiting too long will waste the heat-
ing work carried out by the glow plugs.
Release the key as soon as the engine starts. IMPORTANT With cold engine, the accelerator pedal shall
be completely released while turning the ignition key to
AV V.
If the engine does not start at the first attempt, turn the
ignition key to STOP again before repeating the procedure.
If instrument panel
Ywarning light remains lit when the
ignition key is turned to MAR, turn the key to STOP and
then back to MAR; if the warning light remains lit, try the
other keys provided with the vehicle. Contact a Lancia Deal-
ership if you still cannot start the engine.
The mwarning light will flash for 60 sec-
onds after starting or during prolonged
cranking to indicate a fault with the glow
plug pre-heating system. Use the car normally if the
engine starts and go to a Lancia Dealership as soon
as possible.
183-194 Delta GB 1ed 26/08/13 12.15 Pagina 185

188STARTING AND DRIVING
USING THE GEARBOX
To engage the gears, press the clutch pedal fully and shift
the gear lever into the required position (the gear diagram
varies according to the different versions and is shown
on the knob or on the plate below the lever fig. 2).
To engage 6
thgear, operate the lever by pressing it towards
the right in order to avoid engaging 4thgear by mistake.
The same goes for changing from 6thto 5th.
IMPORTANT The car can only be put into reverse gear
when it has stopped moving completely. With the engine
running, wait at least 2 seconds before engaging reverse
gear with the clutch pedal fully depress in order to avoid
damaging or grinding the gears.
fig. 2L0E0073m
To engage reverse gear R from neutral, raise sliding ring
A under the knob and at the same time move the gear lever
to the left and then forwards.
To engage reverse R from neutral, lift the sliding ring A
under the knob and move the gear lever to the right and
then backwards.
IMPORTANT The clutch pedal should be used only to
change gear. Do not drive with your foot resting on the
clutch pedal, however lightly. For versions/markets where
provided, the electronic clutch pedal control could cut in,
interpreting the incorrect driving style as a fault.
Press the clutch pedal fully to change gears
correctly. Therefore, the floor area under the
pedal unit should be clear: ensure that any
mats are flat and do not interfere with the pedals.
Do not drive with your hand resting on the
gear lever, because this pressure, even if light,
can wear out the internal components of the
gearbox over time.
183-194 Delta GB 1ed 26/08/13 12.15 Pagina 188

190STARTING AND DRIVING
DRIVING STYLE
Cranking
Do not warm up the engine at low or high revs when the
car is stationary: under these conditions the engine warms
up much more slowly, increasing consumption and emis-
sions. It is therefore advisable to move off immediately,
slowly, avoiding high speeds: in this way the engine will
warm up more quickly.
Unnecessary actions
Avoid revving up when at traffic lights or before stopping
the engine. The latter action, like double-declutching, is
completely unnecessary and causes increased fuel con-
sumption and pollution.
Gear selection
As soon as the conditions of the traffic and road permit,
use a higher gear. Using a low gear for faster accelera-
tion will increase consumption.
In the same way improper use of a high gear increases con-
sumption, emissions and engine wear.
Max. speed
Fuel consumption considerably increases as speed in-
creases. Maintain a constant speed, avoiding unnecessary
braking and acceleration, which cost in terms of both fu-
el consumption and emissions.Acceleration
Accelerating violently will greatly affect consumption and
emissions: acceleration should be gradual.
CONDITIONS OF USE
Cold starting
Short journeys and frequent cold starts do not allow the
engine to reach optimum operating temperature. This re-
sults in a significant increase in consumption levels (from
+15 to +30% on the urban cycle) and emissions.
Traffic and road conditions
Rather high fuel consumption is caused by heavy traffic,
for instance when travelling in a queue with frequent use
of low gears or in large towns with many traffic lights.
Mountain and rough roads also have a negative effect on
fuel consumption.
Stops in traffic
During prolonged stops (e.g. level crossings) the engine
should be switched off.
183-194 Delta GB 1ed 26/08/13 12.15 Pagina 190

MAINTENANCE AND CARE235
5
12 24 36 48 60 72 84 96 108 120
20 40 60 80 100 120 140 160 180 2001 2345678910
● ●●●●●●●● ●
● ●●●●●●●● ●
● ●●●●●●●● ●
● ●●●●●●●● ●
● ●●●●●●●● ●
● ● ●●●
● ● ●●●
● ● ●●● ●●●● ●
SCHEDULED SERVICING PLAN
The checks listed in the Scheduled Servicing Plan, after reaching 120,000 km/6 years, must be cyclically repeated starting from
the first interval, thus following the same intervals as before.
Thousands of miles
Thousands of km
Years
Check tyre condition/wear and adjust pressure, if necessary;
check “Fix&Go Automatic” kit recharge expiry date
(for versions/markets, where provided)
Check operation of lighting system (headlamps, direction
indicators, hazard warning lights, luggage compartment,
oddment compartment, instrument panel warning lights, etc.)
Check and, if necessary, top-up fluid levels (brakes/hydraulic
clutch, screen washer, battery, engine cooling, etc.)
Check exhaust fumes/emissions
Use the diagnosis socket to check supply/engine management
system operation; emissions and, for versions/markets,
where provided, engine oil degradation
Visually inspect condition of: exterior bodywork,
underbody protection, rigid and flexible pipes
(exhaust–fuel system–braking system),
rubber elements (boots, hoses, bushes, etc.)
Check windscreen/rear window wiper blade position/wear
Check operation of windscreen wiper/washer system and
adjust jets, if necessary
Check cleanliness of bonnet and boot locks,
cleanliness and lubrication of linkage
233-256 Delta GB 1ed 03/04/14 13:27 Pagina 235