ECO mode Lancia Musa 2007 Owner handbook (in English)

MULTIFUNCTION DISPLAY
(On two-line mode panel)
The “Multifunction display” shows all the useful information
necessary when driving, more particularly:
INFORMATION ON STANDARD SCREEN
❒Mileage recorder (A);
❒Clock (B);
❒Headlight aiming position display (C) (with dipped beam
headlights on).
With ignition key removed and front doors closed the display is off.
With ignition key removed, when opening one of the front doors the
display comes on showing the clock and the total km covered.
If the “Follow me home” function is on (see paragraph “Follow me
home” in this section), the display will show the time the function is
on instead of the mileage recorder indication (see figure).
INFORMATION ABOUT CAR CONDITIONS
❒Trip computer information;
❒Inertial switch operation (at event);
❒Speed limit exceeded (at event).
29
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
L0D0028m
L0D0027m

DISPLAY CONTROL BUTTONS
To use the information the “Multifunction display” is able to give, you
should firstly familiarise with the control buttons using them as
described below.
Before doing anything you are advised to read this section thoroughly.
MODE button
To scroll the display and the related options upwards/downwards.
Press for less than 2 seconds (pulse) to confirm the option required
and/or move to the main screen (same option) or access the Menu.
Press for more than 2 seconds to exit the set-up menu and to confirm
selected options.
+ and – buttons
To increase (+) or to decrease (–) the displayed value or to change
displayed values (see next pages).
TRIP button
Press for less than 2 seconds (pulse) to scroll the Trip computer
screens.
Press for more than 2 seconds to reset the Trip computer and start a
new mission.
IMPORTANT When in set-up menu, to display the Trip computer
info you have first to quit the set-up menu, then use the Trip button
to display the Trip computer info.
30
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
L0D0025m
L0D0026m

SET-UP MENU
The “Set-up Menu” enables to perform the following adjustments
and/or settings:
❒SET CLOCK
❒BUZZER VOLUME
❒SPEED LIMIT
❒SET DISTANCE UNIT.
Set clock
The car is delivered with this function set on 24 hours.
Proceed as follows for the required setting:
❒press repeatedly the MODE button until displaying “Hour”;
❒press +to increase by one minute;
❒press –to decrease by one minute.
Keeping buttons +or–pressed for a few seconds obtains automatic
fast increase or decrease, until releasing the buttons.
❒Press MODE button for over 2 seconds to confirm setting.
31
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
L0D0034m

Buzzer volume
Proceed as follows to set the required volume:
❒press repeatedly the MODE button until displaying “bUZZ”;
❒press +to increase volume;
❒press –to decrease volume;
❒Press MODE button for over 2 seconds to confirm setting.
Speed limit exceeded
With this function it is possible to set the car speed limit which, if
exceeded, automatically sounds a buzzer with the special displaying
to alert the driver.
The car is delivered with this function set to “OFF”.
Proceed as follows for the required setting:
❒press repeatedly the MODE button until displaying “SPEEd”;
❒press +to increase the speed value (max. limit: 250 km/h);
❒press –to decrease the speed value (min. limit: 30 km/h, below
this value the “OFF” mode is resumed);
❒Press MODE button for over 2 seconds to confirm setting.
32
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
L0D0035m
L0D0036m

Set distance unit
Proceed as follows to set the required distance unit (km or miles):
❒press repeatedly the MODE button until displaying “Unit”
❒press +or–to change unit;
❒Press MODE button for over 2 seconds to confirm setting.
33
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
L0D0037m

Cruising range= shows the distance (in km or
miles) that the car can still cover before needing
fuel, assuming that driving conditions are kept
unvaried. The display will show “- - - -” in the
following cases:
❒value for range to empty lower than 50 km or
fuel level below 4 litres; in this event before “- -
- -” the message “Warning, limited range” will
be displayed (this message will be displayed also
if not in TRIP COMPUTER mode);
❒in case of car parked with engine running for a
long period, when the car moves off the range to
empty indication will be displayed again.
Travelled distance= shows the km (or miles)
covered from last reset (*).
Average fuel consumption= shows the average
consumption calculated from last reset (*), this
value can be expressed in l/100 km or mpg.
Instant consumption= shows the fuel
consumption variation updated every second, it can
be expressed in l/100 km or mpg. In case of car
parked with engine running the display will show “-
- - -”. When the car moves off the instant
consumption indication will be displayed again.
Average speed= shows the average speed of the
car in relation with total time elapsed from last reset
(*), this value can be expressed in km/h or in mph.
35
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Travel time= time elapsed from last reset (*).
(*) Reset can be:
– “manual”, reset is performed by the driver by
pressing the relevant button (see paragraph
“Control buttons”)
– “automatic”, reset is performed when the
travelled distance reaches 3999.9 km or when
travel time reaches 99:59 (99 hours and 59
minutes)
– after reconnecting the battery.
IMPORTANT Lacking information, Trip computer
values are displayed with “- - - -”. When restoring
normal operating conditions after a failure,
calculation will restart regularly without resetting
values.
IMPORTANT After battery
disconnection/connection certain displayed values
are equal to “- - - -” until significant data for
calculation are available.

MULTIFUNCTION DISPLAY
(On three-line comfort panel)
The “Multifunction display” shows all the useful information
necessary when driving, more particularly:
INFORMATION ON STANDARD SCREEN
❒Date A.
❒Mileage recorder B.
❒Clock C.
❒External temperature D.
When the ignition key is removed only the time is displayed; when
opening one of the front doors the display comes on showing the
odometer indication.
INFORMATION ABOUT CAR CONDITIONS (at event)
❒Scheduled maintenance programme intervals.
❒ Trip computer information.
❒To adjust the intensity of the instrument dimmer/ menus/
instrument panel, sound system and automatic two-zone climate
control system display.
❒Display of failure/warning messages/function activation.
❒Display of the CITY mode (if selected).
❒Headlight aiming position display (with dipped beam headlights
on) E.
❒Symbol for possible ice on road.
37
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
FOH9000m

CONTROL BUTTONS
To use the information the “Multifunction display” is able to give you
should firstly familiarise with the control buttons using them as
described below.
Before doing anything you are advised to read this section thoroughly.
+ and – buttons
To scroll the menu and the related options upwards/downwards, to
increase/decrease/set the value displayed and, with side/taillights on,
to adjust the intensity of the instrument dimmer/ menus/ instrument
panel, sound system and automatic two-zone climate control system
display (if pressed with “Set-up menu on”).
MODE button
Press for less than 2 seconds (pulse) indicated with
bin the
following diagrams, to confirm the option required and/or move to
the main screen (same option) or access the Menu.
Press for more than 2 seconds indicated with
cin the following
diagrams, to exit the set-up menu during setting.
TRIP button
Press for less than 1 seconds (pulse) indicated with
hin the
following diagrams, to scroll the Trip computer screens.
Press for more than 2 seconds indicated with
iin the following
diagrams, to reset the Trip computer and start a new mission.
38
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
L0D0025m
L0D0026m

41
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
ACCESS TO MENU SCREEN
After the “Initial check”, it is possible to access the menu screen pressing the button
Q.
To surf the menu press buttons +or–.
IMPORTANT If after entering the menu no setting/adjustment is performed within 60 seconds, the system exits
the menu automatically and returns to previously displayed screen.
In this case the last selected but not confirmed setting (through button
Q) is not stored and therefore the
operation shall be repeated.
When the car is running, it is possible to access only the reduced menu (for setting “Speed limit” and “Daylight
sensor automatic headlights”).
When the car is stationary access to the whole menu is enabled.
The following diagram shows the cases described.
Q= Press “MODE” button for less than two seconds
R= Press “MODE” button for over two seconds

43
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Is the car
moving? See
“Initial check”
Extended menu screen
only with the car
at a standstill Example of
standard screen
Menu screen
Q
NO
YES
Speed Lim.
Day Sens.
Exit MenuSpeed Lim.
Light Sensor
Trip B
Clock Adjust.
Clock Mode
Date Adjustm.
Door Lock
Indep. Boot On
Unlock Fda. On
Dist. Unit
Cons.
Temp. Unit
Lang.
Buzzer Vol.
Keys volume
Serv.
Exit Menu
Q= Press “MODE” button for less than two seconds
R= Press “MODE” button for over two seconds