turn signal Lancia Musa 2007 Owner handbook (in English)
[x] Cancel search | Manufacturer: LANCIA, Model Year: 2007, Model line: Musa, Model: Lancia Musa 2007Pages: 346, PDF Size: 5.15 MB
Page 9 of 346
8
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
SYMBOLS
Special coloured labels have been attached near or actually on some
of the components of your Lancia Idea. These labels bear symbols
that remind you of the precautions to be taken as regards that
particular component.
The plate summarising the symbols used can be found under the
bonnet.
THE LANCIA CODE SYSTEM
To further protect you car from theft, it has been fitted with an engine
immobilising system. This system is automatically activated when the
ignition key is removed.
An electronic device, in fact, is fitted in each ignition key grip. The
device transmits a radio-frequency signal when the engine is started
through a special aerial built into the ignition switch. The modulate
signal, which changes each time the engine is started, is the
“password”, by means of which the control unit recognises the key
and enables to start the engine.
OPERATION
Each time the car is started turning the ignition key to MAR, the
Lancia CODE system control unit sends a recognition code to the
engine control unit to deactivate the inhibitor.
The code is sent only if the Lancia CODE system control unit has
recognised the code transmitted from the key.
Each time the ignition key is turned to the STOP position, the Lancia
CODE system deactivates the functions of the engine electronic
control unit.
L0D0012m
Page 97 of 346
96
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Climate control compressor on/off
button B
Press the
√button, when the button
led is on, to switch the compressor
off. The led will go off. By pressing
again the button when the led is off, the system
automatic control of the compressor activation is
restored; this condition is indicated by button led
lighting up.
When the air conditioner compressor is off, the
system deactivates air recirculation to prevent
window misting up. Although the system is still able
to maintain the required temperature, the message
FULL on the display will go off. If the system is no
longer able to keep the required temperature, also
the message AUTO will turn off.
IMPORTANT Air at a temperature lower than that
of the outside air cannot be let into the passenger
compartment when the compressor is off.
Furthermore, in particular environmental
conditions, the windows could mist up fast because
the air is no longer dehumidified.Setting will be stored also when the engine is
stopped.
Either press again button √(in this case the system
operates as heater only) or AUTO to reset automatic
control of the compressor.
With compressor off, if the outside temperature is
higher than the set temperature, the system cannot
reach the required temperature. This will be
signalled by the flashing of set temperature value on
the display for a few seconds, then the message
AUTO will go off.
When the compressor is off, it is possible to reset
manually the fan speed (no bar displayed).
When the compressor is on and the engine is
running, fan speed cannot be lower than the
minimum (one bar displayed).
Page 108 of 346
107
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Turning the knurled ring F it is possible to increase the sensitivity of
the rain sensor.
The increase of the sensitivity of the rain sensor is signalled by a
control and acquisition “stroke”.
Operating the windscreen washer with the rain sensor activated will
start the smart washing function (without the additional cleaning
stroke after five seconds), at the end of which the rain sensor resumes
its normal automatic function.
Deactivation
Remove the stalk from position B or turn the ignition key to STOP.
At the following starting operation (key at MAR), the sensor will not
be reactivated even if the stalk is still at B. To activate the rain sensor,
move the stalk to A or C and then again to B or turn the sensitivity
adjustment knurled ring.
Rain sensor activation is indicated by a wiper “stroke”.
The rain sensor is able to recognize and automatically adjust itself in
the presence of the following particular conditions:
❒impurities on the controlled surface (salt, dirt, etc.);
❒difference between day and night.
Water streaks could cause non-required wiping.WARNING
L0D0073m
Page 151 of 346
“DUALDRIVE” ELECTRIC POWER STEERING
SYSTEM
The car is fitted with an electrically controlled power steering called
“Dualdrive”. It only works when the ignition key is at MAR and the
engine is running and it can be customised by the driver according to
the driving conditions.
ACTIVATION/DEACTIVATION (CITY function)
To turn this function on/off, press the CITY button located in the
middle of the instrument panel.
On some versions the activation of this function is signalled by the
lighting up of the CITY warning light on the instrument panel, on
others by the lighting up of CITY on the reconfigurable multifunction
display.
With the CITY function, the steering wheel will be lighter and require
less effort for parking. This operating strategy is suitable for driving
in cities.
150
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
L0D0122m
It is absolutely forbidden to carry out whatever after-market operation involving
steering system or steering column modifications (e.g.: installation of anti-theft
device) that could badly affect performance and safety.
WARNING
WARNING
Be careful when mounting additional spoilers, alloy rims and non original wheel
caps: they may reduce the brake ventilation and efficiency during sharp and
repeated braking or sloping downhill. Also make sure that nothing (over-
carpeting, etc.) interferes with the pedal stroke.
Page 186 of 346
If you are still unable to start the engine, perform
the emergency start-up procedure (see “Emergency
start-up” in section “In an emergency”) and contact
Lancia Dealership.
IMPORTANT Never leave the ignition key at MAR
when the engine is off.
STARTING PROCEDURE FOR MULTIJET
VERSIONS
Proceed as follows:
❒Ensure that the handbrake is up;
❒Put the gear lever into neutral;
❒Turn the ignition key to MAR: the warning lights
m,UandYwill light up on the instrument
panel;
❒Wait for the warning lights
Yandm. The
hotter the engine is, the quicker this will happen;
❒Press the clutch pedal down to the floor without
touching the accelerator;❒Turn the ignition key to AVV as soon as warning
light
mgoes out. If you wait too long you will
lose the benefit of the work done by the glow
plugs. Release the key as soon as the engine
starts.
IMPORTANT With cold engine, the accelerator
pedal shall be completely released while turning the
ignition key to AVV.
If the engine does not start at the first attempt,
return the ignition key to STOP before repeating
starting.
If, when the ignition key is on MAR, warning light
Y remains lit, turn the key to STOP and then back
to MAR; if the warning light remains on, try with
the other keys provided with the car.
If you still cannot start the engine, contact Lancia
Dealership.
IMPORTANT Never leave the ignition key at MAR
when the engine is off.
185
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
The warning light mwill flash for 60 seconds at start-up or during prolonged cranking to signal
a fault in the glow plug heating system. You can use the car as usual if the engine starts but you
should contact a Lancia Dealership as soon as possible.