ESP Lancia Musa 2008 Owner handbook (in English)

60
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IMPORTANT The fast window
demisting/defrosting function remains
engaged for approx. 3 minutes start-
ing from the time when the engine
coolant exceeds 50°C (petrol versions)
or 35°C (Multijet versions).
When this function is active, the LED
of the corresponding button switches
on and that of the rear window
demister. The text FULL AUTOgoes
off on the display.
You can only adjust the fan speed and
switch the rear window demister off
manually when this function is active.
To restore operating conditions before
this function is activated, press but-
tonF, the air recirculation button C,
the compressor button Bor button
AUTO NorH. Fast window
demisting/
defrosting button F
Press this button: the
climate control system
will automatically switch on all the
functions required for fast windscreen
and front side window demisting/de-
frosting, that is:
❒switches on the climate control
compressor when weather condi-
tions are suitable;
❒disables air recirculation;
❒sets the maximum air temperature
HIin both areas;
❒sets proper fan speed according to
engine coolant temperature to
limit the flow of not sufficiently
warm air to demist the windows
into the passenger compartment;
❒directs the air flow to the wind-
screen and front side windows
vents;
❒engages the rear window mister.Disengagement of the compressor re-
mains stored even after the engine
stops.
To restore automatic compressor con-
trol, press button
√again (in this
case, the system will only work as a
heater) or press AUTO.
With climate control compressor off if
the outside temperature is higher than
the one set, the system will not be able
to keep the required condition, the
temperature value will then start
flashing on the display for a few sec-
onds and the message AUTOgoes off.
With climate control compressor off,
the fan speed can be set to zero man-
ually (no bar shown).
With the compressor enabled and the
engine started, the fan speed may be
reduced to the minimum setting only
(one bar shown).
038-094 MUSA 3ed GB 12-11-2007 11:35 Pagina 60

61
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Switching the
system OFF E
Press button Eto
switch the climate
control system off.
The display will go
out as a consequence.
The following climate control condi-
tions will be established when the sys-
tem is off:
❒LEDs are off;
❒temperatures set are not displayed;
❒air recirculation is enabled, thus
isolating the passenger compart-
ment from external conditions;
❒the climate control compressor is
off;
❒the fan is off.With the system OFF the rear window
demister can either be enabled or dis-
abled manually by pressing button G.
IMPORTANT The system unit stores
the temperatures set before turning
off and resets them when pressing any
button (except heated rear window).
If the function corresponding to the
button pressed is off, it will be turned
on; if on, it will be kept active.
Press button AUTOto switch the the
climate control system on in auto-
matic mode. Demisting/
defrosting button
for rear window
and door mirrors G
Press this button to
activate heated rear window demist-
ing/defrosting. When this function is
on, the button led is on.
This function switches off automati-
cally after a pre-set time or by press-
ing again the button or by turning the
engine off. It will not be switched on
automatically when restarting the en-
gine.
IMPORTANT Do not affix decals on
the inside of the rear window over the
heating filaments to avoid damage
that might cause it to stop working
properly.
038-094 MUSA 3ed GB 12-11-2007 11:35 Pagina 61

68
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
DEVICE DISENGAGEMENT
Turn the knurled ring A-fig. 75to
OFFor the ignition key to STOP. In
addition, the device is automatically
disengaged in one of the following
cases:
❒pressing the brake pedal. TO REDUCE MEMORISED
SPEED
The stored speed can be increased in
two ways:
❒disengaging the device and then
memorising the new speed;
or
❒moving the stalk downwards (
–)
until reaching the new speed which
will be memorised automatically.
Each operation of the stalk will cor-
respond to a slight reduction in speed
(about 1 km/h), while keeping the
stalk downwards will correspond to a
continuous speed reduction. RESTORING STORED SPEED
If the device has been disengaged for
example pressing the brake or clutch
pedal, the memorised speed can be re-
set as follows:
❒accelerate gradually until reaching
a speed approaching the one
memorised;
❒engage the gear selected at the
time of speed memorising (4thor
5thgear);
❒press the button RES B.
TO INCREASE THE
MEMORISED SPEED
The stored speed can be increased
in two ways:
❒pressing the accelerator and then
memorising the new speed
reached;
or
❒moving the stalk upwards (
+).
Each operation of the stalk will cor-
respond to a slight increase in speed
(about 1 km/h), while keeping the
stalk upwards will correspond to a
continuous speed increase.
While travelling with the
device engaged, do not set
the gearshift lever to neutral.
WARNING
In case of malfunctioning
or fault of the device, turn
the knurled ring to OFF and con-
tact the Lancia Dealership, after
checking that the protection fuse is
not blown.
WARNING
038-094 MUSA 3ed GB 12-11-2007 11:35 Pagina 68

81
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
When using the boot, do
not exceed the maximum
admissible loads (see section
“Technical Specifications”). Make
sure that the objects are well
arranged in the boot so that they
will not be projected forwards fol-
lowing sudden braking.
WARNING
When travelling, do not
put any object on the rear
window shelf. they cause cause in-
jury to passengers in the event of
an accident or sudden braking.
WARNING
BOOT ENLARGEMENT WITH
FIXED SEAT
Proceed as follows:
❒attach the buckles to the tongues
(shown by the arrows) fitted on
the backrestfig. 109;
❒ensure that each of the two lengths
C-fig. 110of the side safety belt is
inserted in the respective belt
guide tongue D;
❒lift the cushion Aas shown in the
figure;
❒detach the backrest, by shifting
the levers Band tilt it forwards so
as to obtain a continuous loading
bed;
fig. 109L0D0428m
fig. 110L0D0429m
038-094 MUSA 3ed GB 12-11-2007 11:35 Pagina 81

88
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
ACCESSORIES
PURCHASED BY
THE OWNER
If after buying the car, you decide to
install electrical accessories that re-
quire a permanent electric supply
(sound system, satellite antitheft sys-
tem, etc.) or accessories that in any
case burden the electric supply, con-
tact a Lancia Dealership, whose qual-
ified personnel, besides suggesting the
most suitable devices belonging to
Lineaccessori Lancia, will also evalu-
ate the overall electric absorption,
checking whether the car’s electric
system is able to withstand the load
required, or whether it needs to be in-
tegrated with a more powerful bat-
tery. SET-UP FOR MOBILE PHONE
(where provided)
The combined mobile phone and CD
or CD MP3 sound system set-up con-
sists of:
❒dual function antenna (sound sys-
tem + mobile telephone 900/1800
MHz), located on the roof of the
car;
❒connecting wires to the dual func-
tion antenna and wiring with 10-
way connector.
The connector is located between the
steering column and the central box.
The Customer is responsi-
ble for the purchasing of the
hands-free kit as it must be
compatible with his/her
own mobile phone. It is advisable to
install the microphone near to the
front light.
The maximum power ap-
plicable to the antenna is
20W.
WARNING
For the installation of the
mobile phone and its con-
nection to the set-up existing in the
car, contact a Lancia Dealership so
as to provide for any possible
problems that could damage the
safety of the car.
WARNING
Be very careful when fit-
ting non-standard addi-
tional spoilers, light alloy wheels
or wheel caps: they could reduce
brake ventilation and consequently
brake efficiency in the case of re-
peated, violent braking or on long
downhill roads. Ensure that noth-
ing (e.g. rubber mats) obstructs the
stroke of the pedals.
WARNING
038-094 MUSA 3ed GB 12-11-2007 11:36 Pagina 88

90
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IMPORTANT When making ma-
noeuvres requiring maximum steering
efforts, the steering wheel may be-
come hard to turn; this is normal and
is due to the intervention of the steer-
ing control electric motor overheating
protection system. No repairs are,
therefore, required. The power steer-
ing system will return to normal op-
eration the next time the car is used.
fig. 119L0D0419m
Under no circumstances
should after-market oper-
ations involving steering system or
steering column modifications (e.g.:
installation of anti-theft device) be
carried out, because they could
badly affect performance and
safety, cause the lapse of the war-
ranty and also result in car non-
compliance with homologation re-
quirements.
WARNING
FAILURE INDICATIONS
Any failure of the power steering is in-
dicated by instrument panel warning
light
gcoming on together with the
message on the multifunction display
(see section “Warning lights and mes-
sages”).
In the event of a failure of the electric
power steering, the car continues in
any case to be manoeuvrable with
mechanical steering so that it can be
taken soon as possible to a Lancia
Dealership.
Before servicing the car,
switch off the engine and
remove the key from the ignition
device, activating the steering lock,
especially when car wheels do not
touch the ground. If this is not pos-
sible (if the key must be on MAR or
the engine must be running), re-
move the main fuse which protects
the electric power steering.
WARNING
038-094 MUSA 3ed GB 12-11-2007 11:36 Pagina 90

92
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CAR REFUELLING
PETROL ENGINES
Use only unleaded petrol.
To avoid mistakes, the diameter of the
fuel filler is too small to introduce the
beak of a leaded petrol pump. The
petrol octane rating (RON) must not
be lower than 95.
IMPORTANT An inefficient catalyst
leads to harmful exhaust emissions,
thus contributing to air pollution.
IMPORTANT Never use leaded petrol,
even in small amounts or in an emer-
gency, as this would damage the cat-
alyst beyond repair. GENERAL WARNINGS
❒When parking, take the utmost
care to avoid obstacles that may
be located above or below the
sensors.
❒Objects located near the rear of
the car, under certain circum-
stances are not detected and could
therefore cause damage to the car
or be damaged.
❒Indications sent by the sensors
can be altered by dirt, snow or ice
deposited on the sensors or by ul-
trasound systems (e.g.: truck
pneumatic brakes or pneumatic
hammers) nearby the car. To guarantee the effective
operation of the system, the
sensors must be kept clean
at all times. Be careful not
to scratch or damage the sensors
while cleaning them. Avoid using
dry, rough or hard cloths. Clean the
sensors with clean water with the
addition of car shampoo if neces-
sary. At car wash centres that use
steam or high pressure water jets,
clean the sensors quickly keeping the
nozzle more than 10 cm away.
The driver is, however, al-
ways held responsible for
parking and other dangerous ma-
noeuvres. When carrying out this
manoeuvre, ensure that there are
no people, animals or object within
the manoeuvring area. Parking
sensors are designed to assist dri-
vers: in all cases, you must always
pay the utmost attention during
potentially dangerous manoeuvres.
WARNING
038-094 MUSA 3ed GB 12-11-2007 11:36 Pagina 92

98
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
USING THE CENTRAL
SEAT BELT
The belt has a two buckles and
tongues.
To use the seat belt, extract the
tongues from their housings Hand
P-fig. 5in the reel recess. Then, pull
the belt and let it run freely trying to
avoid twisting and brisk extraction.
Finally, hook the tongue G-fig. 6to
the buckle housing Lwhere button M
has been provided.
To wear the belt, let it run and intro-
duce the tongue I-fig. 6in the hous-
ing corresponding to the relevant
buckleN.
The belt is unfastened as follows.
Press button O-fig. 6and accompany
the belt while it is being rewound to
prevent twisting.
Enlargement of the luggage compart-
ment Press button M-fig. 6to release
the buckle and accompany the belt
during winding to prevent twisting.
Position tongues Iand
G-fig. 6in their housings P-fig. 5and
H-fig. 5 respectively, which are both
positioned in the reel recess.
IMPORTANT Place the seats back in
the travel position and restore the nor-
mal conditions for using the seat belt.
fig. 5L0D0311m
fig. 6L0D0310m
Remember that in the
event of a violent collision,
back seat passengers that do not
wear seat belts both pose a risk for
their safety and also represent a
serious danger for the front seat
passengers.
WARNING
095-112 MUSA 3ed GB 12-11-2007 11:36 Pagina 98

100
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
LOAD LIMITERS
To increase passenger’s safety in the
event of an accident, the front seat
belt reels feature a load limiter which
allows controlled sag in such a way as
to dose the force acting on the chest
and shoulders during the belt re-
straining action in case of front crash.GENERAL INSTRUCTIONS
FOR USING THE SEAT BELTS
The driver is responsible for respect-
ing (and ensuring that all the other
car passengers also respect) the local
laws in force regarding the use of seat
belts. Always fasten the seat belts be-
fore starting off.
Seat belts must also be used by preg-
nant women: wearing the seat belt
significantly reduces the risk for both
the expectant mother and the baby in
the event of an accident.
Pregnant women must position the
lower part of the belt very low down
so that it passes above the hips and
under the abdomen (see fig. 7).
fig. 7L0D0133m
fig. 8L0D0134m
fig. 9L0D0135m
The belt must not be
twisted. The upper part
must cross the shoulder and the
chest diagonally. The lower part
must adhere to the passenger’s hips
and not to the abdomen. Do not use
devices (clips, clamps, etc.) that pre-
vent the belts from being snug to the
passengers’ body.
WARNING
Under no circumstances
should the seat belt and
pretensioner components be re-
moved or tampered with. All in-
terventions must be performed by
qualified and authorised personnel
only. Always go to a Lancia Deal-
ership.
WARNING
Maximum protection is ob-
tained if the backrest is
kept straight: the passenger’s back
must lean against the backrest and
the seat belt must be tight on the
chest and hips. Always fasten the
seat belts on both the front and the
rear seats. Travelling without seat
belts fastened increases the risk of
serious injuries or even death in the
event of a crash.
WARNING
095-112 MUSA 3ed GB 12-11-2007 11:36 Pagina 100

103
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
GROUP 0 and 0+ fig. 10
Babies up to 13 kg must be carried
facing backwards on a cradle seat,
which supports the head, thus not in-
ducing stresses on the baby’s neck in
the event of sharp decelerations.
Cradle seats must be withheld using
the car seat belts. To restrain the baby
use the seat belts fitted in the child
seat.GROUP 1 fig. 11
Children from 9 kg to 18 kg in weight
can be carried facing forwards if the
child seat is fitted with a front cush-
ion, through which the car seat belt
restrains both child and seat.
fig. 11L0D0137mfig. 12L0D0138mfig. 10L0D0136m
The figure is indicative for assembly purposes only. Refer to the
instructions supplied with the child seat.
WARNING
Some child restraint systems for weight group 0 and 1 have a rear
attachment and seat belts for securing the child. Due to their
weight, they may be dangerous if incorrectly mounted (e.g. if fastened to
the car seat belts placing a cushion in between). Follow the assembly in-
structions carefully.
WARNING
GROUP 2 fig. 12
Children from 15 to 25 kg can be se-
cured using the car seat belts directly.
The child seat is only needed to posi-
tion the child correctly with respect to
the belts so that the diagonal section
crosses the child’s chest and never the
neck and is snug on the hips and not
the abdomen.
The figure is indicative for
assembly purposes only.
Refer to the instructions supplied
with the child seat.
WARNING
095-112 MUSA 3ed GB 12-11-2007 11:36 Pagina 103