engine Lancia Musa 2009 Owner handbook (in English)

144
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
If the hub cap is not in-
stalled properly, it can de-
tach itself when the vehicle is run-
ning. Never tamper with the infla-
tion valve. Never introduce tools of
any kind between rim and tyre.
Check tyre and small spare wheel
pressure regularly referring to the
values shown in the “Technical
Specifications” chapter.
WARNINGImportant notes:
❒the jack cannot be repaired: re-
place with an original spare part if
damaged;
❒no tool other than its cranking de-
vice may be fitted on the jack.
To change a wheel proceed as follows:
❒stop the car in a position so that
it is not a danger for on-coming
traffic and where you can replace
the wheel safely. The ground must
be flat and compact;
❒turn the engine off and pull the
handbrake;
❒engage first gear or reverse;
❒raise the mat on the floor of the
baggage compartment;
❒loosen the fastener A-fig. 10;
❒take out the tool container Band
bring it near to the wheel to be
changed;
❒take the small spare wheel C;
L0D0161mfig. 10
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 144

150
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
IF AN EXTERIOR
LIGHT BURNS OUT
For the type of bulb and power rat-
ing, see “When needing to change a
bulb”.
FRONT LIGHT CLUSTERS
The front light clusters contain side-
lights, dipped beam, main beam and
direction indicator bulbs.
To replace the bulbs in the sidelights,
dipped beam and main beam lights,
remove the protective caps.The bulbs are arranged inside the
light unit fig. 17:as follows:
Cdirection indicators
Dmain beam
Bsidelights
Fdipped beam
After replacing the bulbs, put the
protective caps for the lights changed
back into position and ensure that
they are effectively locked into place.IMPORTANT To access the bulb
holder of the left headlight (direction
of travel) in order to replace it, first
remove the protective cover B-fig. 18
of the fuse box in the engine com-
partment.
fig. 17L0D0398mfig. 18L0D0125m
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 150

159
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
FUSE TABLE
Dashboard fuse box
ELECTRICAL DEVICESFUSE AMPERE
Right dipped beam F12 7,5
Left dipped beam / beam aim controlF13 7,5
Engine compartment fuse box relay coil / body computer F31 7.5
AvailableF32 –
Rear left window winderF33 20
Rear right window winderF34 20
+15 Cruise control, signal from switch on brake pedal to control units, reversing light (*) F35 7.5
+30 Set-up for trailer control unit, rear locks front locks with single control unit for the doors (*) F36 10
+15 Third brake light, instrument panel, brake lights (*) F37 7.5
Central locking, fuel flap actuatorF38 20
+30 EOBD diagnosis socket, sound system, navigator, tyre pressure control unit (*)F39 10
Heated rear window F40 30
Heated electric mirrors F41 7.5
+15 ABS / ESP control unit (*)F42 7.5
Wiper/ windscreen washer / rear window washer F43 30
Cigar lighter / console current outletF44 15
Heated seats F45 15
Boot current outletF46 15
Driver side door control unit powering (electric windows) F47 20
Passenger side door control unit powering (electric windows) F48 20
+15 Functions (lighting of controls on left and central panels, electric windows, lighting of heated seat
controls,set-up for mobile phone, navigator, rain / dusk sensors, parking sensors control unit,
lighting of controls for sun roof) (*)F49 7.5
Airbag control unit F50 7.5
+15 Tyre pressure control unitF51 7.5
Wiper/ rear window washer, cigar lighter F52 15
+30 Direction indicators, emergency lights, instrument panel (*) F5 7.5
(*) +30 = battery direct positive terminal (not key-operated)
+15 = positive terminal key operated
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 159

160
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
Fuse box in engine compartment
ELECTRICAL DEVICESFUSEAMPERE
AvailableF9 –
BuzzerF10 15
Electronic injection secondary functionsF11 15
Right main beam F14 7.5
Left main beam F15 7.5
Electronic injection primary functionsF17 10
+30 Engine control unit / radiator electric fan remote diverter (1.9 Multijet) (*) F18 10
CompressorF19 7.5
AvailableF20 –
Fuel pump F21 15
Electronic injection primary functions (1.4 16V)F22 15
Electronic injection primary functions (Multijet)F22 20
+30 Dual FuNction System gearbox control unit (*)F23 30
+15 Electric power steering (*)F24 7.5
Fog lightsF30 15
(*) +30 = battery direct positive terminal (not key-operated)
+15 = positive terminal key-operated
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 160

164
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
fig. 44L0D0251m
HOOKING THE TOW RING
Proceed as follows:
❒take the tow hook B-fig. 45from
its support;
❒tighten the ring on the rear or
front threaded pin.
fig. 45L0D0487m
fig. 46L0D0205m
The power brakes and the
electrical power steering
will not work while the car is being
towed. More effort on the brake
pedal and steering wheel will there-
fore be required. Do not use wires
for towing. Do not jerk. Make sure
not to damage parts in contact with
the car while towing. When towing
the vehicle, be sure to respect the
specific rules of the Highway Code
when towing the car specifically in
relation to the towing device and the
behaviour to maintain on the road.
WARNING
Before beginning the tow,
turn the ignition key to
MAR and then to STOP, without ex-
tracting it When the key is removed,
the steering wheel lock automati-
cally activates. making it impossible
to turn the wheels.
WARNING
During towing do not start
up the engine.
WARNING
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 164

167
WARNING
LIGHTS AND
MESSAGES
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
SERVICE SCHEDULE
Thousands of kilometres
Check tyre conditions/wear and
adjust pressure if required
Check light system operation
(headlights, direction indicators, hazard lights, boot lights,
passenger compartment lights, dashboard warning lights, etc.)
Check windscreen/washer
(nozzles/and blade position regulation)
Check front disc brake pad condition and wear and operation
of brake pad wear indicator.
Check rear drum brake lining conditions
and wear
Check rear (where provided) disk brake pad
conditions and wear
Sight inspect the conditions of: body external parts, underbody
protection pipes and hoses (exhaust, fuel, brakes),
rubber parts (boots, sleeves, bushes, etc.)
Check for bonnet and boot lock cleanness, lever cleanness
and lubrication
Check tension and adjust accessory drive belts
(excluding engines with automatic belt tighteners)
Check tension and adjust accessory drive belts
Check and adjust tappet clearance (1.4 8Vversions)
20 40 60 80 100 120 140 160 180
●●●●● ●●●●
●●●●● ●●●●
●●●●● ●●●●
●●●●● ●●●●
●●●
●● ● ●
●●●●● ●●●●
●●●●● ●●●●
●●
●●
●●●
165-186 MUSA 1ed GB 10-07-2008 9:39 Pagina 167

168
WARNING
LIGHTS AND
MESSAGES
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
Thousands of kilometres
Check and adjust handbrake lever stroke
Check exhaust emissions/smoke (Multijet versions)
Check exhaust emissions (petrol versions)
Change fuel filter cartridge (Multijet versions)
Change air cleaner cartridge (petrol versions)
Change air cleaner cartridge (Multijet versions) (❏)
Top up fluids (engine coolant, brakes, windscreen washer,
battery, Dual FuNction System, etc.)
Check timing belt conditions (■)
Replace timing belt (*) (■)
Replace timing belt (1.6 Multijet versions) (*)
Replace accessory drive belt/s
Change spark plugs (petrol versions)
Check engine control system operation
(through diagnosis socket)
Change engine oil and oil filter (petrol versions)
Change engine oil and oil filter (Multijet versions with DPF) (**)
Change engine oil and oil filter (Multijet versions without DPF) (▲)
Change brake fluid (or every 2 years)
Change pollen filter (or every year)
(*) Or every 4 years for particularly demanding use:
- cold/hot climates;
- driving in the city idling for a long time;
- dusty roads or roads covered with sand and/or salt
Or every 5 years, regardless of the km covered and conditions of use.
(**) Engine oil and oil filter shall be changed when the corresponding warning light turns on (see section “Warning lights and Messages”),
or in any case every 2 years.
(
❏) Every 30.000 km for 1.3 Multijet versions (■) Excluding 1.3 Multijet and 1.6 Multijet versions (▲) Every 30.000 km
20 40 60 80 100 120 140 160 180
●● ● ●
●● ● ●
●● ● ●
●●●
●●●
●●●
●●●●● ●●●●
●●
●
●
●
●● ● ●
●● ● ●
●●●●● ●●●●
●●●
●●●●● ●●●●
165-186 MUSA 1ed GB 10-07-2008 9:39 Pagina 168

169
WARNING
LIGHTS AND
MESSAGES
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
ANNUAL
INSPECTION
SCHEDULE
For cars with an annual mileage of
below 20,000 km (for example about
15.000 km) the following yearly in-
spection programme is advised:
❒check tyre conditions/wear and
adjust pressure if required (in-
cluding the spare wheel);
❒check light system operation
(headlights, direction indicators,
hazard lights, boot lights, passen-
ger compartment lights, warning
lights, etc.);
❒wiper and windscreen washer sys-
tem check (adjustment of spray
nozzles/wear on wiper blades)
❒check front disk brake pad condi-
tions and wear;
❒visually inspect the conditions of:
engine, gearbox, transmission,
pipes and hoses (exhaust - fuel
feed - brakes), rubber parts
(boots, sleeves, bushes, etc.);❒check cleanness of bonnet and
boot locks and lever cleanness and
lubrication;
❒check battery charge;
❒visual check on various drive belt
conditions;
❒check and top up, if required, fluid
levels (engine coolant, brake fluid,
windscreen washer fluid, battery
fluid, etc);
❒replace engine oil;
❒replace engine oil filter;
❒replace pollen filter (where pro-
vided).
ADDITIONAL
CHECKS
Every 1,000 km or before long jour-
neys, check and top up if required:
❒engine coolant fluid level;
❒brake fluid level;
❒windscreen washer fluid level;
❒tyre pressure and conditions.
Every 3,000 km check the following
and top-up, if required: engine oil
level.
You are recommended to use FL Se-
lenia products, designed and pro-
duced specifically for Lancia cars (see
table “Capacities” in section “Techni-
cal specifications”).
IMPORTANT - Engine oil
Should prevailing use of the car be
under one of the following specially
heavy conditions:
❒trailer or caravan towing;
❒dusty roads;
❒short distances (less than 7-8 km)
repeated and with external tem-
peratures below zero;
165-186 MUSA 1ed GB 10-07-2008 9:39 Pagina 169

170
WARNING
LIGHTS AND
MESSAGES
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
❒frequently idling engines or long
distance low speed driving (e.g.
taxis or door-to-door deliveries) or
in case of a long term inactivity;
❒replace engine oil more frequently
than required on “Service sched-
ule”.
IMPORTANT - Air cleaner
If the car is used on dusty roads
change the air cleaner more fre-
quently than the indications in the
“Service schedule”. If in doubt as to
how often the engine oil and air
cleaner should be changed according
to how you use the car, contact a Lan-
cia Dealership.IMPORTANT - Pollen filter
If the car is used frequently in dusty
or heavily polluted environments it is
advisable to replace the filtering ele-
ment more frequently; in particular it
should be replaced if a reduction of
the amount of air admitted to the pas-
senger compartment is noted.
IMPORTANT - Diesel filter
The possibility of topping up with
diesel fuel not complying with EN590
European Norm might make it neces-
sary to replace the filter more fre-
quently than indicated in the “Service
schedule”.IMPORTANT - Battery
The charge in the battery should be
checked at the start of winter to limit
the risk of electrolyte freezing.
Perform this inspection more fre-
quently if the car is mainly used for
short distances or if electrical devices
running with the key off are installed,
particularly after-market. If the car is
used in hot climates or in particularly
heavy duty conditions, it is advisable
to check the battery fluid (electrolyte)
level at more frequent intervals com-
pared to those provided for in the
“Service Schedule”.
Car maintenance should be
entrusted to Lancia Dealer-
ship. For routine and minor
maintenance operations you
wish to carry out yourself, always
make sure you have the proper equip-
ment, genuine Lancia spare parts and
the necessary fluids; do not however
carry out these operations if you have
no experience.
165-186 MUSA 1ed GB 10-07-2008 9:39 Pagina 170

171
WARNING
LIGHTS AND
MESSAGES
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
CHECKING
FLUID LEVELS
IMPORTANT Be careful not to con-
fuse the various types of fluids while
topping up: they are all reciprocally
incompatible and may severely dam-
age your car.
L0D0411m
L0D0412m
fig. 1 - 1.48Vversions (where provided)
fig. 2 - 1.416Vversions
Never smoke while working
in the engine compartment:
flammable gases may be present.
Risk of fire.
WARNING
1 Engine coolant - 2 Engine oil -
3 Brake fluid - 4 Battery - 5 Wind-
screen washer/rear window washer
fluid
165-186 MUSA 1ed GB 10-07-2008 9:39 Pagina 171