tow Lancia Musa 2009 Owner handbook (in English)

20
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IGNITION DEVICE
The key can be turned to 3 different
positions:
❒STOP: engine off, key extractable,
steering locked. Some electrical
devices (e.g. sound system, power
windows, etc.) work regularly.
❒MAR: driving position. All electri-
cal devices work regularly.
❒AV V: engine starting (unstable po-
sition).
The ignition switch is fitted with an
electronic safety system that turns the
ignition key back to position STOPif
the engine will not start, before re-
peating the starting operation.
Under no circumstances
should aftermarket works
be carried out, because they may
cause tampering with the driving
system or steering column (e.g. in-
stallation of anti-theft device), which
may lead to reduced system perfor-
mances and loss of the warranty as
well as safety-specific problems and
non-compliance with the car type-
approval.
WARNING
fig. 21L0D0021m
If the ignition system is
tampered with (e.g. after an
attempted theft), address a Lancia
Dealership to have the system
checked before starting off.
WARNING
Always remove the key
from the car when leaving
it in order to prevent accidental en-
gagement of the controls. Remem-
ber to engage the handbrake. En-
gage first gear if the car is parked
uphill or reverse if the car is parked
downhill. Never leave children un-
attended in the car.
WARNING
STEERING COLUMN LOCK
Engagement
When the key is in position STOP, re-
move the key and turn the steering
wheel until it is locked.
Disengagement
Rock the steering wheel slightly as you
turn the ignition key to MAR.
Never extract the key while
the car is moving. The steer-
ing wheel would be locked as soon as
the steering wheel is turned. This also
applies to cases in which the car is
towed.
WARNING
007-037 MUSA 1ed GB 10-07-2008 9:36 Pagina 20

57
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
The distribution mode set is indicated
by the LEDs that light up on the se-
lected buttons.
In combined function mode the rele-
vant function is enabled simultane-
ously with those already set by press-
ing the corresponding button. If a
button is pressed for a function that
is active, the operation is cancelled
and the corresponding LED goes off.
To restore automatic air distribution
control after a manual selection, press
buttonAUTO.
When the driver selects air distribu-
tion to the windscreen, the air distri-
bution on the passenger’s side too is
aligned to the windscreen. The pas-
senger can select a different distribu-
tion mode by pressing the corre-
sponding buttons.Buttons
AUTO H-N
(automatic
operation)
Press button AUTOon
the driver’s side and/or
front passenger’s side
to automatically adjust
the amount and distri-
bution of air delivered
to the passenger com-
partment, thus can-
celling the previously made manual ad-
justments.
The message FULL AUTOwill ap-
pear on the front display in this con-
dition.
When at least one of the functions
managed by the system is manually
changed (air recirculation, air distri-
bution, fan speed or climate control
system compressor off), the message
FULLon the display goes off to indi-
cate that the system is no longer
checking all the functions one by one
(the temperature is still automatic). Fan speed
adjustment buttons
L
Press the ends of but-
ton
pto increase or to
decrease the fan speed and conse-
quently the amount of air delivered to
the passenger compartment, although
keeping the required temperature set-
ting.
The fan speed is shown by the lit bars
on the display.
❒Max. fan speed = all bars lit;
❒Min. fan speed = one bar lit.
The fan can be cut off only if the cli-
mate control compressor has been
switched off pressing button B.
IMPORTANT To restore automatic
fan speed control after a manual ad-
justment, press button AUTO.
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 57

59
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IMPORTANT Air recirculation ON
enables faster achievement of the de-
sired conditions (for passenger com-
partment heating or cooling). It is
however inadvisable to use it on
rainy/cold days as it would consider-
ably increase the possibility of the
windows misting inside, especially if
the climate control compressor is off.
Recirculation is forced to off (i.e. air
is introduced from the outside) when
the outside temperature is inferior to
5-7°C to prevent misting up.Climate control
compressor on/off
button B
Press button
√when
the LED on it goes on.
The LED goes off when the climate
control compressor is switched off.
Press the button when the LED is off
to automatically restore system con-
trol and use of the compressor. Suc-
cessful completion of this operation is
highlighted by the button LED
switching on.
The system will switch recirculation
off when the compressor is switched
to off to prevent windows from mist-
ing up. Although the system is capa-
ble of maintaining the required tem-
perature, the word FULLwill disap-
pear from the display. If on the other
hand the system cannot maintain the
required temperature, the digits will
blink and the word AUTOwill disap-
pear.
IMPORTANT With the compressor
off, it is not possible to introduced air
cooler than ambient temperature into
the passenger compartment. Further-
more, in certain conditions, the win-
dows could mist up rapidly because
the air is not dehumidified.
It is advisable not to use the
air recirculation function
when the outside temperature is low
to prevent the windows from rapidly
misting up.
WARNING
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 59

62
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
PARKING LIGHTS fig. 67
With the ignition key in position STOP
or removed, rotate knurled ring in po-
sition
6. The warning light 3is lit
on the instrument panel and all the
plate lights and side/taillights go on.
Move the lever
aupwards to turn on
the lights on the right-hand side; move
it downwards
bto turn on the lights
on the left-hand side. In both cases the
warning light
3on the instrument
panel does not turn on. FLASHING THE HEADLIGHTS
Pull the stalk towards the steering
wheel (unstable position) regardless
of the position of the knurled ring.
The warning light
1on the instru-
ment panel will come on at the same
time.
fig. 63L0D0066m
fig. 66L0D0069m
fig. 65L0D0068m
fig. 64L0D0067m
EXTERNAL LIGHTS
The left-hand lever includes the con-
trols for the external lights.
The external lights can only be
switched on when the ignition key is at
MAR.
LIGHTS OFF fig. 63
Knurled ring turned to position
å.
SIDE/TAILLIGHTS fig. 64
Turn the knurled ring to position
6.
The warning light
3on the instru-
ment panel comes on at the same time.
DIPPED BEAM HEADLIGHTS fig.
65
Turn the knurled ring to position
2.
The warning light
3on the instru-
ment panel comes on at the same time.
BEAM HEADLIGHTS fig. 66
When the knurled ring is in position
2pull the lever towards the steering
wheel (stable position). The warning
light
1on the instrument panel comes
on at the same time.
To turn the beam headlights off, pull
again the lever towards the steering
wheel (dipped beams will turn on
again).
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 62

63
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
DIRECTION INDICATORS
fig. 67
Push the stalk to (stable) position:
❒up (position 1): right-hand indica-
tor ON;
❒down (position 2): left-hand indi-
cator ON.
Warning light
ForDstart flashing
on the instrument panel.
Indicators are switched off automati-
cally when the steering wheel is
straightened.
If you want the indicator to flash
briefly to show that you are about to
change lane, move the stalk up or
down without clicking into position
(unstable position). When released,
the stalk will return to its home posi-
tion.AUTOMATIC LIGHT SENSORS
(dusk sensor) (where provided)
This sensor detects any changes in the
external brightness according to the
sensitivity of the set light level: the
higher the sensitivity, the lower the
amount of external light needed to
switch the lights on. The sensitivity of
the dusk sensor is adjusted by means
of the “Setup menu” on the “Multi-
functional Display”.
Activation
Rotate the knurled ring in position
2A
fig. 69as to cause automatic switch-
ing on of the side/tail lights and low
beam lights simultaneously depend-
ing on the external brightness. “FOLLOW ME HOME”
DEVICE fig. 68
This function allows the illumination
of the space in front of the car for a
preset period of time.
Activation
With the ignition key on STOPor re-
moved, pull the stalk towards the
steering wheel within 2 minutes from
when the engine is turned off.
At each single movement of the stalk,
the time in which the lights stay on is
extended by 30 seconds up to maxi-
mum 210 seconds. After this time, the
lights go off automatically.
fig. 67L0D0071mfig. 68L0D0070mfig. 69L0D0072m
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 63

65
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Operation in position Eis limited to
the time during which the lever is
kept in that position manually..
When released, the stalk will return
to position Aand the wiper will be
automatically stopped.
IMPORTANT Replace wiper blades
as specified in section “Car
maintenance”.RAIN SENSOR
(where provided)
The rain sensor is located behind the
driving mirror in contact with the
windscreen and has the purpose of
automatically adjust the frequency of
the windscreen wiper strokes as to the
rain intensity.
IMPORTANT Keep the window clean
in the sensor area.
Activation
Move the right lever down by one
click.
The activation of the rain sensor is
signalled by a control acquisition
“stroke”.
Turn the knurled ring F-fig. 73to in-
crease the rain sensor sensitivity.
The increase of the sensitivity of the
rain sensor is signalled by a control
and acquisition “stroke”.
By operating the windscreen washer
with the rain sensor enabled, a smart
washing cycle is carried out, without
the additional stroke after 5 seconds;
once completed, the sensor resumes its
regular automatic operation. “Smart washing” function
Pull the stalk towards the steering
wheel (unstable position) to operate
the windscreen washer.
Keeping the stalk pulled for more
than half a second, with just one
movement it is possible to operate the
washer jet and the wiper at the same
time.
When releasing the stalk, the jet stops
immediately, while the wiper carries
out another four strokes.
A further stroke after 6 seconds com-
pletes the wiping operation. Do not use the windscreen
wiper to remove layers of
snow or ice from the wind-
screen. In such conditions,
the windscreen wiper may be sub-
jected to excessive stress and the mo-
tor protection which prevents opera-
tion for a few seconds may trip. If the
issue persists, contact the Lancia
Dealership.
fig. 72L0D0074m
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 65

66
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
With windscreen wiper on and reverse
gear engaged, rear window wiping
will be continuous.
Pushing the stalk towards the dash-
board (unstable position) will activate
the rear window washer.
Keeping the stalk pushed for over half
a second will activate also the rear
window wiper.
Releasing the stalk will activate the
smart washing function as described
for the windscreen wiper. The sensor reactivation is signalled by
a windscreen wiper “stroke”.
The rain sensor is able to recognize
and automatically adjust itself in the
presence of the following particular
conditions:
❒impurities on the controlled sur-
face (salt, dirt, etc.);
❒difference between day and night.
Deactivation
Change the stalk knurled ring posi-
tion from Bor turn the ignition key to
STOP.
At the next start-up (key at MAR), the
sensor will not be reactivated even if
the stalk is at B. To activate the sen-
sor, move the stalk to position AorC
and then to position Bor turn the sen-
sitivity adjustment knurled ring.
fig. 73L0C0073m
Streaks of water may cause
unnecessary blade moving.
WARNING
REAR WINDOW WASHER/
WIPER fig. 74
The device can work only when the
ignition key is on MAR.
Turning the knurled ring Afrom po-
sition
åto position 'will operate the
rear window wiper as follows:
❒intermittent operation if the
windscreen wiper is off;
❒synchronised with the windscreen
wiper (but with half stroke fre-
quency);
fig. 74L0D0075m
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 66

67
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CRUISE CONTROL
(constant speed
regulator)
(where provided)
It is a device able to support the dri-
ver, with electronic control, which al-
lows driving at speed over 30 km/h
on long and straight dry roads (e.g.:
motorways), at a desired speed, with-
out pressing the accelerator pedal.
Therefore it is not suggested to use
this device on extra-urban roads with
traffic. Do not use it in town.TO MEMORISE SPEED
Proceed as follows:
❒turn knurling ring A-fig. 75toON
and press the accelerator pedal to
the required speed;
❒push the lever up (+) for at least
three seconds, then release it: the
car speed will be stored. The ac-
celerator pedal may be released.
If needed (e.g. for overtaking), press
the accelerator pedal to accelerate: the
car will return to the previously set
speed when the pedal is released. DEVICE ENGAGEMENT
Turn the knurling ring A-fig. 75to
ON.
The device must be enabled only with
4
thor 5thgear engaged. Travelling
downhill with the device engaged, the
car speed may increase more than the
memorised one. When the device is
activated the instrument panel warn-
ing light Üturns on and the relevant
message (where provided) is dis-
played on the multifunctional display.
fig. 75L0D0076m
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 67

82
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
BONNET
OPENING THE BONNET
Proceed as follows:
❒pull lever A-fig. 111in the direc-
tion indicated by the arrow;
❒shift the lever towards the left B-
fig. 113 as shown by the arrow;
❒lift the bonnet and at the same
time release the rod C-fig. 112
from the catch D, then fit end of
the rod into the bonnet recess E.
IMPORTANT Before opening the
bonnet, check that windscreen wiper
arms are not lifted from the wind-
screen.
fig. 111L0D0113m
fig. 112L0C0115m
fig. 113L0D0392m
The bonnet must always be
perfectly closed while trav-
elling for safety reasons. Make sure
that the bonnet is perfectly closed
and that the lock is engaged. If you
discover that the bonnet is not per-
fectly closed while travelling, stop
immediately and close the bonnet in
the correct manner.
WARNING
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 82

91
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Detection distances
The central radius of action varies ac-
cording to the engine/ trim of the car:
The recognition area is equivalent to
140 cm, while for small obstacles (or
in the case of parking bollards which
have a rounded shape) it is equivalent
to 70 cm. The lateral radius of action
has a recognition area of 60 cm.
If several obstacles are detected, the
control unit indicates the nearest one.
FAILURE INDICATIONS
See “Warning lights and messages”
section.
OPERATION WITH TRAILER
The system is programmed to deacti-
vate automatically when the trailer
electric cable plug is fitted into the car
tow hook socket.
Sensors are reactivated on removing
the trailer cable plug. BUZZER WARNINGS
When the reverse gear is engaged an
intermittent acoustic signal is auto-
matically activated.
The acoustic signal:
❒becomes louder as the reduction of
distance between the car and the
obstacle decreases;
❒becomes continuous when the dis-
tance between the car and the ob-
stacle is less than 30 cm and stops
immediately if the distance in-
creases;
❒iremains constant if the distance
between vehicle and obstacle re-
mains unvaried; if this situation
concerns the side sensors, the
buzzer will stop after about 3 sec-
onds to avoid, for example, warn-
ing indications in the event of ma-
noeuvres along walls.
fig. 120L0D0395m
GENERAL WARNINGS
❒When parking, take the utmost
care to avoid obstacles that may
be located above or below the
sensors.
❒Objects located near the rear of
the car, under certain circum-
stances are not detected and could
therefore cause damage to the car
or be damaged.
❒Indications sent by the sensors
can be altered by dirt, snow or ice
deposited on the sensors or by ul-
trasound systems (e.g.: truck
pneumatic brakes or pneumatic
hammers) nearby the car.
038-094 MUSA 1ed GB 11-07-2008 14:11 Pagina 91