dashboard Lancia Musa 2010 Owner handbook (in English)

57
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
The set distribution is shown by the
corresponding LEDs on the selected
buttons. When the combined function
is on, press a button to activate the
corresponding functions along with
the settings. If the button correspond-
ing to a previously active button is
pressed, the function is turned off and
the corresponding LED will go out.
To restore automatic air distribution
control after a manual adjustment,
press button AUTO.
Air distribution is automatically
aligned on driver and passenger side
when the driver selects air distribu-
tion towards the windscreen. The pas-
senger can select a different distribu-
tion by pressing the corresponding
buttons afterwards.AUTO H-N
buttons (automatic
operation)
Press AUTOdriver’s
side and/or passenger’s
side to automatically
adjust the air speed
and air distribution in
the corresponding
zones cancelling al pre-
vious manual settings.
The message FULL AUTOwill ap-
pear on the front display in this con-
dition.
By manually intervening on at least of
the functions automatically managed
by the system (air recirculation, fan
speed or compressor on/off), the word
FULLwill disappear from the display
indicating that the system is no longer
automatically controlling all the func-
tions (the temperature will still be
controlled automatically by the sys-
tem). Fan speed
adjustment
buttons L
Press button
pto in-
crease or to decrease
the fan speed and therefore the
amount of air admitted into the pas-
senger compartment, although keep-
ing the required temperature set.
The fan speed is shown by the lit bars
on the display:
❒Maximum fan speed = all bars lit
❒Minimum fan speed = one bar lit.
The fan can be cut off only if the cli-
mate control compressor has been
switched off pressing button B.
IMPORTANT To restore automatic
fan speed control after a manual ad-
justment, press button AUTO.

58
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Air recirculation
on/off button C
Air recirculation
works according to
the following operat-
ing logics:
❒forced switching on (inside air re-
circulation always on), indicated by
the turning off of the button led C
and symbol
íon the display;
❒function off (air recirculation al-
ways off and introduction of ex-
ternal air), indicated by the fact
that the LED on the button will go
off and symbol
êwill appear on
the display.
These operating conditions are ob-
tained by pressing Cin sequence.
For safety reasons, the system will au-
tomatically turn the recycle function
off to allow the introduction of fresh
air after a certain time. MONO A button
(for aligning
temperature and
air distribution
settings)
Press MONOto automatically align
air temperature and distribution set-
tings in the front passenger area to
those of in the driver’s area and to
therefore set both zones by turning
the knob on driver’s side only. This
function is used to adjust the temper-
ature in the entire passenger com-
partment in presence of the driver
only. To go back to separate air and
temperature distribution in the two
zones of the passenger compartment,
simply turn the knobs Hor press
A-MONOwhen the LED on the but-
ton is on. IMPORTANT Should the system (af-
ter manual settings) be no longer able
to guarantee the required temperature
set in the passenger compartment, the
set temperature value will start flash-
ing to indicate this condition, after
one minute the AUTOmessage will go
out.
To restore system automatic control at
any time, after one or more manual
adjustments, press button AUTO.

59
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
IMPORTANT The air recirculation
function makes it possible to reach the
required heating or cooling conditions
faster. It is however inadvisable to use
it on rainy/cold days as it would con-
siderably increase the possibility of
the windows misting inside, especially
if the climate control compressor is
off.
Recirculation is forced off (i.e. air is
introduced from the outside) when
the the outside temperature is colder
than 5-7°C to prevent misting up.Climate control
compressor on/off
button B
Press button
√when
the LED on the but-
ton is on, to turn the climate control
compressor off. The LED will go out.
Press the button when the LED is off
to restore automatically system con-
trol and use of the compressor. The
LED will light up on the button in
this case.
The system will switch recirculation
off when the compressor is switched
off to prevent misting up. Although
the system is capable of maintaining
the required temperature, the word
FULLwill disappear from the display.
If on the other hand the system can-
not maintain the required tempera-
ture, the digits will blink and the word
AUTOwill disappear.
IMPORTANT With the compressor
off, it is not possible to introduced air
cooler than ambient temperature into
the passenger compartment. Further-
more, in certain conditions, the win-
dows could mist up rapidly because
the air is not dehumidified.
It is advisable not to use
the air recirculation func-
tion when the outside temperature
is low to prevent the windows from
rapidly misting up.
WARNING

60
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
IMPORTANT The fast demist/defrost
function will remain on for approxi-
mately 3 minutes, from when the en-
gine coolant reaches a temperature of
50°C (petrol versions) or 35°C (Mul-
tijet versions).
When this function is on, the LED of
the corresponding button switches on
and that of the rear window demister.
The message FULL AUTOgoes off on
the display.
You can only adjust the fan speed and
switch the rear window demister off
manually when this function is active.
To restore running operations before
this function was activated, press ei-
ther button F, air recirculation button
C, compressor button Bor button
AUTO NorH. Fast window
demisting/
defrosting
button F
Press this button: the
climate control system will automati-
cally switch on all the functions re-
quired for fast windscreen and front
side window demisting/defrosting,
that is:
❒climate control compressor on
when weather conditions are suit-
able;
❒air recycle off;
❒maximum air temperature HIon
both areas;
❒proper fan speed according to en-
gine coolant temperature to limit
the flow of not sufficiently warm air
to demist the windows into the pas-
senger compartment;
❒air flow to the windscreen and
front side windows vents;
❒the heated rear window on The switching off of the climate con-
trol compressor remains in storage
even when the engine has been
stopped.
To restore automatic compressor con-
trol, press
√again (in this case, the
system will only work as a heater) or
press AUTO.
When the compressor is off, if the ex-
ternal temperature is hotter than the
set temperature and the system can-
not satisfy the request, the digits of
the set temperature will blink for a
few seconds and the message AUTO
will go out.
With climate control compressor off,
the fan speed can be set to zero man-
ually (no bar shown).
With the compressor on and the en-
gine started, the fan speed may be re-
duced to the minimum setting (only
one bar shown).

61
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Switching the
system off E
Press Eto switch the
climate control system
off. The display will
go out as a conse-
quence.
The following climate control condi-
tions will be established when the sys-
tem is off:
❒LEDs off;
❒set temperature not shown;
❒air recirculation on, passenger com-
partment isolated from the outside;
❒air conditioner compressor off;
❒fan off.The rear window heater can be turned
on and off manually by pressing G
when the system is off.
IMPORTANT The climate control sys-
tem control unit stores the settings be-
fore the system is turned off and rep-
resents the same settings when it
turned back on by pressing any but-
ton (except for the heated rear win-
dow). If the function corresponding to
the pressed button was off, it will be
turned on; if it was on, it will be kept
on.
Press AUTOto turn the climate con-
trol system in fully automatic mode. Rear window
heater and external
rearview mirror
heater on/off
button G
Press this button to turn the rear win-
dow demister/defroster on. The LED
in the button will light up when the
function is on.
The heater will go out automatically
after a certain time or by pressing the
button again. It will also go out when
the engine is stopped until it is started
again.
IMPORTANT Do not apply stickers
over the electric filaments on the in-
side of the rear window to prevent
damage and ensure perfect operation.

62
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
PARKING LIGHTS fig. 65
With the key at STOPor extracted,
turn the ring to position
6. Warning
light
3on the instrument panel will
go on with the side/taillights and the
number plate lights. Move the stalk
upwards
ato turn on the right side
lights only; move it downwards bto
turn on the left side lights only. In ei-
ther case, warning light
3will not
light up on the instrument cluster. FLASHING THE HEADLIGHTS
Pull the stalk towards the steering
wheel (unstable position) regardless
of the position of the ring. The warn-
ing light
1on the instrument cluster
will come on at the same time.
fig. 61L0D0066m
fig. 64L0D0069m
fig. 63L0D0068m
fig. 62L0D0067m
EXTERNAL LIGHTS
The left-hand lever includes the con-
trols for the external lights.
The external lights can only be
switched on when the ignition key is
atMAR.
LIGHTS OFF Fig. 61
Turn the ring to position
å.
SIDE/TAIL LIGHTS Fig. 62
Turn the ring to
6.
The warning light
3on the instru-
ment cluster will come on at the same
time.
DIPPED BEAM HEADLIGHTS
fig. 63
Turn the ring to
2.
The warning light
3on the instru-
ment cluster will come on at the same
time.
BEAM HEADLIGHTS Fig. 64
With the ring at
2, pull the lever to-
wards the steering wheel (permanent
position).
The warning light
1on the instru-
ment cluster will come on at the same
time.
To turn the beam headlights off, pull
again the lever towards the steering
wheel (dipped beams will turn on
again).

63
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
DIRECTION INDICATORS
Fig. 65
Push the stalk to (stable) position:
❒upwards (position 1): right-hand
indicator;
❒downwards (position 2): left-hand
indicator;
Warning light
ForDcomes on in-
termittently on the instrument panel.
Indicators are switched off automati-
cally when the steering wheel is
straightened.
If you want the indicator to flash
briefly to show that you are about to
change lane, move the stalk up or
down without clicking into position
(unstable position). When released
the stalk will return to its home posi-
tion.AUTOMATIC LIGHT SENSORS
(dusk sensor)
(for versions/markets, where provided)
This sensor detects changes of exter-
nal lights according to the sensitivity
of the setting: the higher the sensitiv-
ity, the lower the amount of external
light needed to switch the lights on.
The sensitivity of the dusk sensor is
adjusted by means of the “Setup
menu” on the “Multifunctional dis-
play”.
Activation
Turn the ring to
2Afig. 67to light up
the side/tail lights and dipped beam
headlights according to the external
brightness. “FOLLOW ME HOME”
DEVICE fig. 66
This function allows the illumination
of the space in front of the car for a
preset period of time.
Activation
With the ignition key on STOPor re-
moved, pull the stalk towards the
steering wheel within 2 minutes from
when the engine is turned off.
At each single movement of the stalk,
the lights will remain on for an extra
30 seconds up to a maximum of 210
seconds; then the lights are switched
off automatically.
fig. 65L0D0071mfig. 66L0D0070mfig. 67L0D0072m

64
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
CLEANING THE
WINDOWS
WINDSCREEN WASHER/
WIPER
The device can only work when the
ignition key is at MAR.
The right hand stalk can take up five
different positions:
Awindscreen wiper off
Bflick operation.
With the lever in position B, turn the
knurled ring Fto select one of four
different speeds for the intermittent
operation mode:
,= very slow flick
--= slow flick
---= medium flick
----= fast flick The set sensitivity level of the sensor
will appear on the multifunctional
display when the automatic headlight
sensor is on. Adjust sensitivity by
pressing
+and–(seefig. 68) while
the setting appears on the display.
Deactivation
When the command to switch off is
given by the sensor, the dipped head-
lamps are deactivated and then the
side lights about 10 seconds later.
If the main beam heads are turned on
(manually by the driver) while the au-
tomatic headlight function is on, the
main beam headlights will be turned
off when the lights are automatically
turned off.
IMPORTANT The sensor cannot de-
tect the presence of fog: switch the
lights on manually in this case.
fig. 68L0D0384m
fig. 69L0C0073m
Ccontinuous slow
Dcontinuous fast
Etemporary fast operation (unstable
position).

65
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Operation in position Eis limited to
the time during which the lever is
kept in that position manually. When
released, the stalk will return to posi-
tionAand the wiper will be automat-
ically stopped.
IMPORTANT Replace wiper blades as
specified in the “Maintenance and
care” chapter. RAIN SENSOR
(for versions/markets, where provided)
The rain sensor is located behind the
driving mirror in contact with the
windscreen and has the purpose of
automatically adjusting the frequency
of the windscreen wiper strokes as to
the rain intensity.
IMPORTANT Keep clean the glass in
the sensor area.
Activation
Move the right stalk down by one
click.
The activation of the rain sensor is
signalled by a control acquisition
flick.
Turn the ring F-fig. 71to increase the
rain sensor sensitivity.
The increase of the sensitivity of the
rain sensor is signalled by a control
and acquisition flick.
The smart cycle is started when the
windscreen wiper is turned on while
the rain sensor is active without sup-
plementary flick after 5 seconds. The
sensor will resume normal automatic
operation. “Smart washing” function
Pull the stalk towards the steering
wheel (unstable position) to operate
the windscreen washer.
Keeping the stalk pulled for more
than half a second, with just one
movement it is possible to operate the
washer jet and the wiper at the same
time.
The jet will be released immediately
when the wiper stops after four flicks.
A further stroke after 5 seconds com-
pletes the wiping operation. Do not use the windscreen
wiper to remove layers of
snow or ice from the wind-
screen. In such conditions,
the windscreen wiper may be sub-
jected to excessive stress and the
motor protection which prevents op-
eration for a few seconds may trip.
If rear window wiper operation is
not reset, contact a Lancia Dealer-
ship.
fig. 70L0D0074m

66
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
❒in synchronous mode (at half the
frequency of the windscreen
wiper) when the windscreen wiper
is running.
The rear window wiper will run in
continuous mode when the wind-
screen wiper is running and reverse
gear is engaged.
Pull the stalk towards the dashboard
(unstable position) to operate the rear
window washer.
Hold the stalk pushed for longer than
half a second to operate the rear win-
dow wiper as well.
Smart wash function is activated as
for the windscreen wiper when the
stalk is released. The wiper will flick once to indicate
that the sensor has been reactivated.
The rain sensor is able to recognize
and automatically adjust itself in the
presence of the following particular
conditions:
❒dirt on the controlled surface (salt,
dirt, etc.);
❒difference between day and night.
Deactivation
Move the lever from position Bor turn
the ignition key to STOP.
At the next start-up (key at MAR),
the sensor will not be reactivated even
if the stalk is at B. To activate the sen-
sor, move the stalk to position AorC
and then to position Bor turn the sen-
sitivity adjustment knurled ring.
fig. 71L0C0073m
Streaks of water may
cause undesired blade
moving.
WARNING
REAR WINDOW WIPER/
WASHER fig. 72
The device can only work when the
ignition key is at MAR.
Turn ring Afrom position
åto posi-
tion'to open the rear window wiper
as follows:
❒in flick mode when the windscreen
wiper is not running
fig. 72L0D0075m