ECO mode Lancia Musa 2010 Owner handbook (in English)

23
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
CONTROL BUTTONS fig. 25
+To scroll the menu and the next
options or to increase the dis-
played value.
MODEPress briefly to access the
menu and/or go to next
screen or to confirm the re-
quired menu option.
Hold pressed to go back to
the standard screen.
–To scroll the menu and the previ-
ous options or to decrease the dis-
played value.
NOTE Buttons
+and–activate dif-
ferent functions according to the fol-
lowing situations.❒Hold buttonMODE pressed for
longer than two seconds to con-
firm the change made to the time.
Setting the buzzer volume
To set the desired volume, proceed as
follows:
❒repeatedly press MODEto display
“bUZZ”;
❒press +to increase the volume;
❒press –to decrease the volume;
❒Hold buttonMODE pressed for
longer than two seconds to con-
firm the change made.
Setting the speed limit
A speed limit can be set and the sys-
tem will inform the drive when the
limit is exceeded by means of an in-
dication on the display and the
buzzer. Proceed as follows to set:
This function is “OFF” when the car
is delivered.
SET-UP MENU
The “Set-up Menu” is used for the
following adjustments and/or settings:
❒SETTING THE CLOCK
❒SETTING THE BUZZER VOL-
UME
❒SETTING THE SPEED LIMIT
❒SETTING THE UNIT OF MEA-
SUREMENT.
Setting the clock
The clock is set to 24 hours when the
car is delivered.
Proceed as follows to set the required
time:
❒repeatedly press MODEto display
“Hour”;
❒press +to increase one minute;
❒press –to decrease one minute;
Hold buttons +or–pressed for a few
seconds to run the clock forwards or
backwards rapidly until the buttons
are released.
fig. 25L0D0384m

24
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Setting the unit of measurement
Proceed as follows to set the required
unit of measurement (kilometres or
miles):
❒repeatedly press MODEto display
Unit”;
❒press button +or–to change the
unit of measurement;
❒to confirm the setting, hold button
MODEpressed for longer than
two seconds.
Fuel inertia
switch tripped indication
The indication appears automatically
if the fuel inertia switch trips follow a
collision of considerable severity.
The switch cuts off fuel feed.
See the “Fuel inertia switch” chapter
for more information. Proceed as follows to select:
❒repeatedly press MODEuntil
“SPEEd” appears;
❒press +to increase the value cor-
responding to speed (the maxi-
mum limit is 250 km/h);
❒press –to decrease the value cor-
responding to speed (the limit is
30 km/h under which it switches
to “OFF”);
❒to confirm the setting, hold button
MODEpressed for longer than
two seconds.
If after the “FPSon” mes-
sage appears, you smell
fuel or see leaks from the fuel sys-
tem, do not reset the switch to
avoid fine risk.
WARNING

25
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
fig. 26L0D0496m
MULTIFUNCTIONAL
DISPLAY
(on three-line
comfort panel)
The car can be equipped with the
multifunction display for showing
useful information necessary when
driving according to settings.
“STANDARD” SCREEN fig. 26
The standard screen shows the fol-
lowing information:
ADate / Odometer (covered km or
miles).
BClock (always displayed, even
with ignition key removed and
front doors closed).
CExternal temperature. CONTROL BUTTONS fig. 27
+To scroll the menu and the next
options or to increase the dis-
played value.
MODEPress briefly to access the
menu and/or go to next
screen or to confirm the re-
quired menu option.
Hold pressed to go back to
the standard screen.
–To scroll the menu and the previ-
ous options or to decrease the dis-
played value.
NOTE Buttons
+and–activate dif-
ferent functions according to the fol-
lowing situations. DHeadlight adjustment (only with
dipped beam headlights on).
EGear shift suggestion.
NOTE When opening one of the front
doors, the display will turn on and
show for a few seconds the clock and
the kilometres or miles covered.
fig. 27L0C0384m

37
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Start trip procedure
With ignition key on MAR, press and hold button TRIPpressed for over 2 seconds to reset.
Quitting TRIP
TheTRIPfunction shuts down automatically after displaying all the data. Alternatively, hold MODEpressed for longer
than two seconds.
Reset TRIP B
End of partial mission
Start of new partial mission
End of partial mission
Start of new
partial mission
Reset TRIP B
End of partial mission
Start of new
partial mission GENERAL TRIP reset
End of complete mission
Start of new mission GENERAL TRIP reset
End of complete mission
Start of new mission
End of partial mission
Start of new
partial mission Reset TRIP B
Reset TRIP B
TRIP B
TRIP B
TRIP B GENERAL TRIP
˙
˙
˙
˙
˙
˙˙
˙
fig. 30

64
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
CLEANING THE
WINDOWS
WINDSCREEN WASHER/
WIPER
The device can only work when the
ignition key is at MAR.
The right hand stalk can take up five
different positions:
Awindscreen wiper off
Bflick operation.
With the lever in position B, turn the
knurled ring Fto select one of four
different speeds for the intermittent
operation mode:
,= very slow flick
--= slow flick
---= medium flick
----= fast flick The set sensitivity level of the sensor
will appear on the multifunctional
display when the automatic headlight
sensor is on. Adjust sensitivity by
pressing
+and–(seefig. 68) while
the setting appears on the display.
Deactivation
When the command to switch off is
given by the sensor, the dipped head-
lamps are deactivated and then the
side lights about 10 seconds later.
If the main beam heads are turned on
(manually by the driver) while the au-
tomatic headlight function is on, the
main beam headlights will be turned
off when the lights are automatically
turned off.
IMPORTANT The sensor cannot de-
tect the presence of fog: switch the
lights on manually in this case.
fig. 68L0D0384m
fig. 69L0C0073m
Ccontinuous slow
Dcontinuous fast
Etemporary fast operation (unstable
position).

66
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
❒in synchronous mode (at half the
frequency of the windscreen
wiper) when the windscreen wiper
is running.
The rear window wiper will run in
continuous mode when the wind-
screen wiper is running and reverse
gear is engaged.
Pull the stalk towards the dashboard
(unstable position) to operate the rear
window washer.
Hold the stalk pushed for longer than
half a second to operate the rear win-
dow wiper as well.
Smart wash function is activated as
for the windscreen wiper when the
stalk is released. The wiper will flick once to indicate
that the sensor has been reactivated.
The rain sensor is able to recognize
and automatically adjust itself in the
presence of the following particular
conditions:
❒dirt on the controlled surface (salt,
dirt, etc.);
❒difference between day and night.
Deactivation
Move the lever from position Bor turn
the ignition key to STOP.
At the next start-up (key at MAR),
the sensor will not be reactivated even
if the stalk is at B. To activate the sen-
sor, move the stalk to position AorC
and then to position Bor turn the sen-
sitivity adjustment knurled ring.
fig. 71L0C0073m
Streaks of water may
cause undesired blade
moving.
WARNING
REAR WINDOW WIPER/
WASHER fig. 72
The device can only work when the
ignition key is at MAR.
Turn ring Afrom position
åto posi-
tion'to open the rear window wiper
as follows:
❒in flick mode when the windscreen
wiper is not running
fig. 72L0D0075m

69
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
CEILING LIGHTS
FRONT CEILING LIGHT
fig. 74
SwitchA-turns these lights on/off .
With switch Ain central position,
lightsCandDwill turn on/off when
opening/closing the front doors.
With switch Apressed on the left side,
lightsCandDwill always stay off.
With switch A-pressed on the right
side, lights CandDwill always stay
on.
The lights will be turned on/off grad-
ually.
SwitchBis used for operating the
spot light function; it works as follows
(light off):
❒lightCif the left side is pressed;
❒lightDif pressed on the right side.Lights when getting into the car
Lights will be turned on as follows:
❒for about 10 seconds when the door
is unlocked;
❒for about 3 minutes when a door is
opened;
❒for about 10 seconds when the
doors are closed (within the three
minutes).
Timing will stop when turning the ig-
nition key to MAR.
Light when getting out of the car
After removing the key from the igni-
tion switch, the lights will turn on as
follows:
❒within 2 minutes from turning the
engine off for about 10 seconds;
❒when a door is opened for about 3
minutes;
❒for about 10 seconds when the
doors are closed (within the three
minutes).
Timing will stop automatically when
locking the doors. IMPORTANT Before getting out of
the vehicle, make sure the switch is at
central position: lights off with doors
closed in order to avoid draining the
battery.
In any case, if the switch is left inad-
vertently to the on position, the lights
will turn off automatically 15 minutes
after turning the engine off.
Courtesy light timing
On certain versions to facilitate get-
ting in/out of the car at night or with
poor lighting, 2 different timed
switching on modes have been pro-
vided.
fig. 74L0D0077m

70
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Light when getting out of the car
After removing the key from the igni-
tion switch, the lights will turn on as
follows:
❒within 2 minutes from turning the
engine off for about 10 seconds;
❒when a door is opened for about 3
minutes;
❒for about 10 seconds when the
doors are closed (within the three
minutes).
Timing will stop automatically when
locking the doors. Ceiling light timer
(for versions/markets, where provided)
On certain versions to facilitate get-
ting in/out of the car at night or with
poor lighting, 2 different timed
switching on modes have been pro-
vided.
Lights when getting into the car
Lights will be turned on as follows:
❒for about 10 seconds when the door
is unlocked;
❒for about 3 minutes when a door is
opened;
❒for about 10 seconds when the
doors are closed (within the three
minutes).
Timing will stop when turning the ig-
nition key to MAR. REAR COURTESY LIGHT
The light will turn on/off by pressing
the lens rightwards or leftwards
as shown in fig. 75.
The light may be integrated in the
ceiling unit, where provided.
Two 5W ceiling lights fig. 76are pre-
sent if a sunroof is fitted.
fig. 75L0D0078mfig. 76L0D0254m

126
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
GENERAL WARNINGS
Warning lights are associated to a spe-
cific message and/or buzzer when ap-
plicable. Indications are brief and pre-
cautionaryand as such must non be
considered as exhaustive and/or alter-
native to the information contained in
the Owner’s Handbook, which you are
recommended to read carefully in all
cases. Refer to the information in this
chapterin the event of a failure in-
dication.
IMPORTANT Failure indications on
the display fall into either of two cat-
egories:seriousfaults and less seri-
ousfaults.
A warning cycle will be repeated in
case of severefailures until the case
of the problem is eliminated.
A shorter warning cycle will be run in
case of less severefaults.
PressMODEto stop the warning cy-
cle in both cases. The warning light
on the instrument panel will stay on
until the cause of the fault is elimi-
nated.LOW BRAKE FLUID
(red)
HANDBRAKE ON (red)
When the ignition key is moved to
MAR, the warning light turns on and
should go off after a few seconds.
Low brake fluid level
The warning light comes on when the
level of the brake fluid in the reservoir
falls below the minimum level due to
possible leaks in the circuit.
The display will show the dedicated
message.
x
Handbrake on
The warning light turns on when the
handbrake is on.
On certain versions, if the car is mov-
ing the buzzer will also sound.
IMPORTANT If the warning light
turns on when travelling, check that
the handbrake is not engaged.
AIRBAG FAILURE (red)
When the ignition key is
moved to MAR, the warn-
ing light turns on and should
go off after a few seconds.
The warning light stays on steady if
there is a failure in the airbag system.
The display will show the dedicated
message.
¬
If the warning light x
turns on when travelling
(with the message on the display)
stop the car immediately and con-
tact Lancia Dealership.
WARNING

128
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
LIGHT STAYS ON:
LOW ENGINE OIL
PRESSURE (red)
FLASHING LIGHT:
EXHAUSTED ENGINE OIL
(only Multijet versions
with DPF - red)
When the ignition key is turned to
MAR (ON), the warning light switches
on and should go out as soon as the
engine is started.
1. Low engine oil pressure
The warning light turns on and stays
on constantly (for versions/markets,
where provided) along with the mes-
sage on the display when the system
detects that engine oil pressure is low.
v
2. Exhausted engine oil
(only Multijet versions
with DPF)
The warning light will flash and
a specific message will appear on the
display (for versions/markets, where
provided). The warning light may
flash in the following ways, depend-
ing on the version:
– for 1 minute every two hours;
– for 3 minute cycles with the warn-
ing light off for intervals of 5 seconds
until oil is changed.
After the initial warning, each time
the engine is started up, the warning
light will continue to flash in the
above mentioned modes, until the oil
is changed. A specific message will
appear on the display (for versions/
markets, where provided) in addition
to the warning light.
If the warning light flashes, this does
not mean that the car is defective but
simply informs the driver that it is
now necessary to change the oil as
a result of regular vehicle use.
If the warning light v
turns on when the vehicle
is travelling (on certain versions
together with the message on the
display) stop the engine immedi-
ately and contact a Lancia Deal-
ership.
WARNING
Note that engine oil is exhausted faster
under the following circumstances:
– use of the vehicle prevalently for city
driving, requiring more frequent re-
generation of DPF
– use of the vehicle for short drives, in
which the engine does not have time
to reach its regular operating temper-
ature
– repeated interruption of the regen-
eration process, signalled by the DPF
warning light coming on.
WARNING
Exhausted engine oil should
be replaced as soon as pos-
sible after the warning light comes
on, never more than 500 km after
the warning light first comes on.
Failure to change the oil within the
first 500 km may result in severe
damage to the engine and will re-
sult in forfeiture of the warranty.
Remember that when the warning
light flashes, it does not mean that
the level of engine oil is low, so if
the light flashes you must not top
up.