display Lancia Musa 2010 Owner handbook (in English)

ELECTRIC ACCESSORIES
If, after buying the car, you decide to add electric accessories (that will gradually drain the battery),
visit a Lancia Dealership. They can calculate the overall electric requirement and check that the car’s
electric system can support the required load.

CODE card
Keep the card in a safe place, non in the car. Have the electronic code printed on the CODE card with you
at all times. You will need it to start the engine in an emergency.
SCHEDULED SERVICING
Correct maintenance of the car is essential for ensuring it stays in tip-top condition and safeguards its
safety features, its environmental friendliness and low running costs for a long time to come.
THE OWNER’S HANDBOOK CONTAINS…
... important information, advise and warnings for correct use, driving safety and maintenance of your car
in time. Pay special attention to the symbols "(personal safety) #(environmental protection) â(car
integrity).
Refer to the “Warning lights and messages” chapter in this handbook if the message “see Handbook”
appears on the display.

7
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLSDASHBOARD ........................................................ 8
INSTRUMENT PANEL.......................................... 10
SYMBOLS ............................................................. 11
THE LANCIA CODE SYSTEM .............................. 11
KEY KIT AND DOOR LOCKING SYSTEM .......... 13
IGNITION SWITCH ............................................. 20
INSTRUMENTS ................................................... 21
MULTIFUNCTIONAL DISPLAY
(ON TWO-LINE MODAL PANEL) ........................ 22
MULTIFUNCTIONAL DISPLAY
(ON THREE-LINE COMFORT PANEL) ............... 25
ADJUSTING THE SEATS ..................................... 38
HEAD RESTRAINTS ........................................... 44
ADJUSTING THE STEERING WHEEL ............... 45
REAR VIEW MIRRORS ........................................ 46
CLIMATE CONTROL SYSTEM ........................... 47
MANUAL CLIMATE CONTROL SYSTEM ........... 48
AUTOMATIC TWO-ZONE CLIMATE CONTROL
SYSTEM ................................................................ 52
EXTERNAL LIGHTS ........................................... 62
CLEANING THE WINDOWS ............................... 64
CRUISE CONTROL ............................................. 67
CEILING LIGHTS ................................................ 69
LIGHT CONTROL BUTTONS .............................. 71FUEL CUT OFF SWITCH ..................................... 72
INTERIOR EQUIPMENT ..................................... 73
SMOKER’S KIT ..................................................... 75
SUN VISORS ........................................................ 76
SUNROOF ............................................................ 76
WINDOW WINDERS ............................................ 78
BOOT ................................................................... 80
BONNET .............................................................. 82
ROOF RAILS ........................................................ 83
HEADLIGHTS ..................................................... 84
ABS SYSTEM ....................................................... 85
EOBD SYSTEM .................................................... 86
GSI SYSTEM ......................................................... 87
SOUND SYSTEM ................................................. 87
ACCESSORIES PURCHASED BY THE OWNER . 88
“DUAL DRIVE” ELECTRIC POWER STEERING
SYSTEM ............................................................... 89
PARK SENSOR ..................................................... 90
REFUELLING ...................................................... 92
PROTECTING THE ENVIRONMENT ................. 94
DASHBOARD AND CONTROLS

10
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
L0D0372m
L0D0010m
fig. 7
fig. 8
INSTRUMENT PANEL
Modal fig. 7
A – Speedometer
B – Fuel level gauge with reserve warning light
C – Engine coolant temperature gauge and hot
engine coolant warning light
D – Rev counter
E – Multifunctional display
cmWarning lights for Multijet versions only
Comfort fig. 8
A – Speedometer
B – Fuel level gauge with reserve warning light
C – Engine coolant temperature gauge and hot
engine coolant warning light
D – Rev counter
E – Reconfigurable multifunctional display
cmWarning lights for Multijet versions only

12
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Warning light
Ycoming on
when driving
❒If the warning light Yturns on,
this means that the system is run-
ning a self-test (for example for a
voltage drop).
❒If the fault persists, contact a Lan-
cia Dealership.
OPERATION
Each time the car is started turning
the ignition key to MAR, the Lancia
CODE system control unit sends a
recognition code to the engine control
unit to activate the functions. The
code is sent only if the Lancia CODE
system control unit has recognised the
code transmitted from the key. Each
time the ignition key is turned to
STOP, the Lancia CODE system de-
activates the functions of the engine
electronic control unit.
If the code has not been recognised
correctly, the warning light
Yturns
on on the display.The electronic components
inside the key may be dam-
aged if the key is submitted
to sharp knocks.
In this case, turn the key to STOP
and then back to MAR; try with the
other keys provided if the problem
persists. Contact a Lancia Dealership
if you still cannot start the engine.
IMPORTANT Each key has its own
code which must be stored by the sys-
tem electronic control unit. Contact a
Fiat Dealership to have new keys (up
to eight) stored.

14
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
By using the “Setup Menu” of the
multifunctional display (see the spe-
cific paragraph in the “Dashboard
and controls” chapter), the system
can be set so that only the driver’s
door is unlocked when button Ëis
pressed.
IMPORTANT Powerful radio trans-
missions not related to the car (e.g.
mobile phones, amateur radios, etc.)
may interfere with the frequency of
the remote control. Remote control
operation may be impaired.
Unlocking the doors and the
tailgate
Press button Ábriefly: this will release
the doors, the tailgate, the fuel flap;
the internal ceiling light will come on
and the direction indicators will blink
twice. Unlocking the doors and the
tailgate
Press button Ëbriefly: this will release
the doors, the tailgate, the fuel flap;
the internal ceiling light will come on
and the direction indicators will blink
twice.
The doors are automatically unlocked
when the fuel inertia switch trips. To insert the metallic part Aback in
the grip:
❒hold buttonBpressed
❒move the metallic part A
❒release button Band then turn the
metal insert Auntil it clicks.
Button
Ëis used to open the doors,
tailgate and fuel flap (where pro-
vided).
Button
Áis used to lock the doors,
tailgate and fuel flap (where pro-
vided).
ButtonRis used for remote open-
ing the tailgate.
Only press button B with
the key away from your
body, specifically from your eyes
and from objects which could get
damaged (e.g. your clothes). Do not
leave the key unattended, because
someone, a child especially, may
accidentally press the button while
handling the key.
WARNING

22
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
MULTIFUNCTIONAL
DISPLAY
(on two-line modal
panel)
The car can be equipped with the mul-
tifunction display for showing useful in-
formation necessary when driving ac-
cording to settings. ENGINE
COOLANT TEMPERATURE
GAUGE fig. 23
Warning light Aindicates overheating
of the engine coolant. In this case, stop
the engine and contact a Lancia Deal-
ership. This shows the temperature of
the engine coolant fluid and starts
working when the fluid temperature ex-
ceeds approx. 50°C. In normal condi-
tions, the needle may point to different
positions according to use and the en-
gine cooling system management.
IMPORTANT The needle will point to
the lowest value of the scale (low tem-
perature) and warning light Awill
light up to indicate a fault in the sys-
tem. Go to a Lancia Dealership to
have the system checked.
If the needle reaches the red
area, stop the engine imme-
diately and contact a Lan-
cia Dealership.
fig. 24L0D0497m
“STANDARD” SCREEN fig. 24
The standard screen shows the fol-
lowing information:
AOdometer (kilometres or miles
travelled)
BClock (always displayed, even
with key extracted and front doors
closed)
CHeadlight adjustment (only with
dipped beam headlights on)
DGear shift suggestion.
NOTE When opening one of the front
doors, the display will turn on and
show for a few seconds the clock and
the kilometres or miles covered.

23
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
CONTROL BUTTONS fig. 25
+To scroll the menu and the next
options or to increase the dis-
played value.
MODEPress briefly to access the
menu and/or go to next
screen or to confirm the re-
quired menu option.
Hold pressed to go back to
the standard screen.
–To scroll the menu and the previ-
ous options or to decrease the dis-
played value.
NOTE Buttons
+and–activate dif-
ferent functions according to the fol-
lowing situations.❒Hold buttonMODE pressed for
longer than two seconds to con-
firm the change made to the time.
Setting the buzzer volume
To set the desired volume, proceed as
follows:
❒repeatedly press MODEto display
“bUZZ”;
❒press +to increase the volume;
❒press –to decrease the volume;
❒Hold buttonMODE pressed for
longer than two seconds to con-
firm the change made.
Setting the speed limit
A speed limit can be set and the sys-
tem will inform the drive when the
limit is exceeded by means of an in-
dication on the display and the
buzzer. Proceed as follows to set:
This function is “OFF” when the car
is delivered.
SET-UP MENU
The “Set-up Menu” is used for the
following adjustments and/or settings:
❒SETTING THE CLOCK
❒SETTING THE BUZZER VOL-
UME
❒SETTING THE SPEED LIMIT
❒SETTING THE UNIT OF MEA-
SUREMENT.
Setting the clock
The clock is set to 24 hours when the
car is delivered.
Proceed as follows to set the required
time:
❒repeatedly press MODEto display
“Hour”;
❒press +to increase one minute;
❒press –to decrease one minute;
Hold buttons +or–pressed for a few
seconds to run the clock forwards or
backwards rapidly until the buttons
are released.
fig. 25L0D0384m

24
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Setting the unit of measurement
Proceed as follows to set the required
unit of measurement (kilometres or
miles):
❒repeatedly press MODEto display
Unit”;
❒press button +or–to change the
unit of measurement;
❒to confirm the setting, hold button
MODEpressed for longer than
two seconds.
Fuel inertia
switch tripped indication
The indication appears automatically
if the fuel inertia switch trips follow a
collision of considerable severity.
The switch cuts off fuel feed.
See the “Fuel inertia switch” chapter
for more information. Proceed as follows to select:
❒repeatedly press MODEuntil
“SPEEd” appears;
❒press +to increase the value cor-
responding to speed (the maxi-
mum limit is 250 km/h);
❒press –to decrease the value cor-
responding to speed (the limit is
30 km/h under which it switches
to “OFF”);
❒to confirm the setting, hold button
MODEpressed for longer than
two seconds.
If after the “FPSon” mes-
sage appears, you smell
fuel or see leaks from the fuel sys-
tem, do not reset the switch to
avoid fine risk.
WARNING

25
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
fig. 26L0D0496m
MULTIFUNCTIONAL
DISPLAY
(on three-line
comfort panel)
The car can be equipped with the
multifunction display for showing
useful information necessary when
driving according to settings.
“STANDARD” SCREEN fig. 26
The standard screen shows the fol-
lowing information:
ADate / Odometer (covered km or
miles).
BClock (always displayed, even
with ignition key removed and
front doors closed).
CExternal temperature. CONTROL BUTTONS fig. 27
+To scroll the menu and the next
options or to increase the dis-
played value.
MODEPress briefly to access the
menu and/or go to next
screen or to confirm the re-
quired menu option.
Hold pressed to go back to
the standard screen.
–To scroll the menu and the previ-
ous options or to decrease the dis-
played value.
NOTE Buttons
+and–activate dif-
ferent functions according to the fol-
lowing situations. DHeadlight adjustment (only with
dipped beam headlights on).
EGear shift suggestion.
NOTE When opening one of the front
doors, the display will turn on and
show for a few seconds the clock and
the kilometres or miles covered.
fig. 27L0C0384m

26
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Headlight adjustment (only
with dipped beam headlights on).
– when the standard page is dis-
played, this is used to adjust the head-
lights (see the “Headlights” para-
graph in this chapter).
Set-up menu
– for scrolling the menu up and down;
–to increase or decrease values during
settings.
SET-UP MENU Fig. 28
The menu comprises a series of func-
tions arranged in a “circular fashion”
which can be selected through buttons
+and–to access the different select
operations and settings (setup) given
in the following paragraphs.
The setup menu is activated by press-
ing briefly button MODE.
Single presses on buttons
+and–will scroll the setup menu options.
Handling modes are different accord-
ing to the characteristic of the option
selected.Selecting “Date” and “Clock”:
– briefly press button MODEto select
the first value to be changed (e.g.
hours /minutes or year / month /
day).
– press buttons
+and–(by single
presses) to select the new setting;
– briefly press button MODEto store
the new setting and go to the next
setup menu option: if this is the last
one you will go back to the previously
selected option of the main menu.
Hold the
button MODE pressed to:
– quit set-up and to save only the
changes stored by the user (and con-
firmed by pressing button MODE).
The setup menu environment is
timed. Only the changes saved by the
user by briefly pressing MODE).ill be
saved when the menu is automatically
closed. NOTE Only the following functions
can be adjusted/set on the Instrument
Panel display if the Connect Nav+
system is present: “Lights”, “Speed
limit”, “Light sensor” (for versions/
markets, where provided), “Belt
buzzer” and “Passenger airbag”. The
other functions are shown on the
Connect Nav+ system display. Set and
adjustment them there.
Selecting a menu option
– briefly press button MODEto se-
lect the menu option that needs to be
changed.
– press buttons
+and–(by single
presses) to select the new setting;
– briefly press button MODEto store
the new setting and at the same time
go back to the previously selected
menu option.