torque LAND ROVER DEFENDER 1996 User Guide

ENGINE
3
SPECIFICATIONS, TORQUENm
Turbo charger oil drain adaptor to block 42....................................................
Oil drain pipe to turbocharger 25....................................................................
Turbocharger oil drain pipe to adaptor 38.......................................................
Turbocharger oil feed pipe adaptor to block 25...............................................
Turbocharger oil feed pipe to adaptor 25........................................................
Oil feed pipe to turbocharger 19.....................................................................
Turbocharger to cylinder head (stud) 10.........................................................
Turbocharger to cylinder head (nut) 45...........................................................
Turbocharger to blanking plate 25..................................................................
Turbocharger to EGR valve 25.......................................................................
EGR delivery tube to valve 25........................................................................
EGR delivery tube to mixing tube 25..............................................................
Fuel lift pump to filter (union) 15.....................................................................
Fuel filter from lift pump (banjo bolt) 33...........................................................
Fuel filter to fuel injection pump (banjo bolt) 33..............................................
Fuel injection pump from fuel filter (banjo bolt) 25..........................................
Injector pipes to injectors and fuel injection pump 29.....................................
Spill rail to injectors (banjo bolt) 10.................................................................
Spill rail to injection pump (banjo bolt) 25.......................................................
Boost pipe injection pump (banjo bolt) 10.......................................................
Plug, rear of injection pump 29.......................................................................
PAS pump to mounting plate 25.....................................................................
PAS pump mounting plate to auxiliaries mounting bracket 25........................
PAS pump pulley to hub 25............................................................................
Starter motor (bolt and nut) 45........................................................................
Air conditioning compressor
Compressor mounting bracket to front cover 45.............................................
Compressor to mounting bracket (stud) 8......................................................
Compressor to mounting bracket (nut) 25......................................................
Belt tensioner pulley to tensioner arm 45........................................................
Belt tensioner assembly to front cover plate 25..............................................
Idler pulley to front cover plate 45...................................................................
Compressor belt guard (nut) 25......................................................................
Sensors to water outlet elbow (air/con) 25......................................................
Blanking plug, water outlet elbow (air/con) 25................................................
Generator
Generator mounting bracket to front cover 45................................................
Generator to mounting bracket 85..................................................................
Generator pulley to hub 95.............................................................................
Generator belt guard 25..................................................................................
Generator to auxiliaries mounting bracket 25.................................................
Tachometer electrical connection 4...............................................................

12ENGINE
4
SPECIFICATIONS, TORQUEMETRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12 90...................................................................................................
M14 105..................................................................................................
M16 180..................................................................................................
UNC / UNF
1/4 9......................................................................................................
5/16 24...................................................................................................
3/8 39.....................................................................................................
7/16 78...................................................................................................
1/2 90.....................................................................................................
5/8 136....................................................................................................
NOTE: Torque values above are to be used as a guide where no torque is specified.

26COOLING SYSTEM
4
DESCRIPTION AND OPERATION Operation
To engage and disengage the fan drive the bi-metal
coil senses air temperature behind the radiator. When
a pre-determined temperature is reached, the coil
opens a valve (5) which allows fluid to enter the drive
area and, due to centrifugal force, circulates to the
annular drive area.
There are two sets of annular grooves (3), one in the
drive clutch and the other in the drive body, a specific
clearance being provided between the two sets of
grooves.
Viscous unit disengaged (engine at normal
running temperature)
1.Input (drive) member
2.Output (driven) member
3.Running clearance
4.Pump plate
5.Valve (closed)
6.Sensing mechanism (bi-metal coil)
7.Fluid seal
8.Bearing, input member
9.Fluid chamber
10.Fluid reservoirWhen this clearance is filled with viscous fluid, a
shearing action, caused by the speed differential
between the two drive components, transmits torque
to the fan. The fluid is thrown to the outside of the unit
by centrifugal force from where it is recirculated to the
reservoir (10) via the pump plate (4) adjacent to the
drive member.
If the engine speed is increased the amount of slip will
also increase to limit the maximum fan speed.
When the air temperature from the radiator drops
sufficiently, the bi-metal coil closes the valve and
prevents fluid entering the drive area. The fluid that is
in the drive area will gradually pump out into the
reservoir (10) and the fan will return to an idle
condition.
Viscous unit engaged (hot running temperature)
Bi-metal coil (6) expanded, valve (5) open.

COOLING SYSTEM
1
REPAIR VISCOUS COUPLING AND FAN
Service repair no - 26.25.19 - Viscous coupling
Service repair no - 26.25.05 - Fan
Remove
NOTE: The viscous coupling has a LH
thread.
1.Disconnect battery.
2.Using special pulley restraining toolLRT-12-094
and special spannerLRT-12-093unscrew
viscous coupling from pulley hub adaptor thread.
3.Remove viscous coupling and fan from vehicle.
NOTE: If air conditioning is fitted, the fan
cowl will also need removing,
See Fan
cowl
, with the viscous fan unit.
4.If required, remove 4 screws and release
viscous unit from fan blade.
Refit
5.Fit viscous unit to fan blades.
6.If applicable, fit fan cowl.
See Fan cowl
7.Carefully position viscous coupling and fit onto
pulley hub adaptor thread.
8.Using special pulley retaining tool, spanner and
a suitable torque wrench, tighten assembly to
45
Nm (33 lbf/ft).

MANUAL GEARBOX
1
SPECIFICATIONS, TORQUE REV: 05/99 TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Slave cylinder to bell housing 25....................................................................
Breather 15.....................................................................................................
Bell housing to cylinder block 40.....................................................................
High/low level to shaft 2.................................................................................
Transfer box to gearbox 45.............................................................................
NOTE: Torque values below apply to all screws and bolts used unless otherwise specified.
METRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12 90...................................................................................................
M14 105..................................................................................................
M16 180..................................................................................................
UNC / UNF
1/4 9......................................................................................................
5/16 24...................................................................................................
3/8 39.....................................................................................................
7/16 78...................................................................................................
1/2 90.....................................................................................................
5/8 136....................................................................................................

TRANSFER GEARBOX
1
SPECIFICATIONS, TORQUE REV: 05/99 TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Transfer gearbox
Pinch bolt - operating arm to crank arm 9......................................................
End cover gear change housing 9.................................................................
Bottom cover to transfer case 25....................................................................
Front output housing to transfer case 25........................................................
Cross shaft housing to front output housing 25...............................................
Gear change housing 25.................................................................................
Pivot shaft to link arm 25.................................................................................
Connecting rod to adjustable clevis 25...........................................................
Anti-rotation plate intermediate shaft 25.........................................................
Front output housing cover 25........................................................................
Pivot bracket to extension housing 25............................................................
Finger housing to front output housing 25......................................................
Bearing housing to transfer case 25...............................................................
Brake drum to coupling flange 25...................................................................
Bearing housing cover to transfer gearbox 45................................................
Rear output speedometer housing to transfer gearbox 45..............................
Selector finger to cross shaft high/low 25.......................................................
Selector fork, high/low to shaft 25...................................................................
Transmission brake to speedometer housing 72............................................
Gate plate to grommet plate 9.......................................................................
Gearbox to transfer case 45...........................................................................
Oil drain plug 30..............................................................................................
Oil filler/level plug 30.......................................................................................
Differential case (front to rear) 60...................................................................
Output flanges 162...........................................................................................
Differential case rear stake nut 72..................................................................
Transfer breather 15.......................................................................................
Transfer box front drive flange to drive shaft 45..............................................
Transfer box rear drive flange to drive shaft 45..............................................
Transfer gearbox mounting brackets to chassis 30........................................
Mounting brackets to transfer gearbox 55......................................................
Mounting rubbers to mounting brackets 21.....................................................

51REAR AXLE AND FINAL DRIVE
2
REPAIRREV: 05/99 Refit
15.Position axle and fit lower links. Tighten fixings
to
176 Nm (130 lbf/ft).
16.If applicable, fit anti-roll bar links to axleSee
REAR SUSPENSION, Repair, Anti-roll bar
links
.
17.Raise axle and locate road springs.
18.Fit coil spring retaining plates and secure with
fixing bolts.
19.Secure pivot bracket ball joint to axle bracket.
Tighten fixing to
176 Nm (130 lbf/ft).
20.Align propeller shaft to differential drive flange
and tighten fixings to
47 Nm (35 lbf/ft).
21.Reconnect flexible brake hose and axle breather
hose.
22.Refit shock absorbers.
23.Fit road wheels and tighten to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy Duty wheels -170 Nm (125 lbf/ft)
24.Remove rear chassis support.
25.Bleed brake system
See BRAKES, Repair,
brake system bleed
.

51REAR AXLE AND FINAL DRIVE
4
REPAIRREV: 05/99 Refit
10.Clean stub axle.
11.Fit hub assembly to stub axle.
12.Fit spacing washer.
13.Fit hub adjusting nut. Tighten to
50 Nm (37
lbf/ft).
Ensure hub is free to rotate with no
bearing play. Back off adjusting nut 90°and
tighten to
10 Nm (7 lbf/ft).
14.Fit a new lock washer.
15.Fit locknut. Tighten to
50 Nm (37 lbf/ft).
16.Tab over lock washer to secure adjusting nut
and locknut.
17.Using a new joint washer fit axle shaft to hub.
Tighten bolts to
65 Nm (48 lbf/ft).
18.Fit brake caliper. Tighten bolts to82 Nm (61
lbf/ft).
Secure brake pipes to axle casing.
19.Fit road wheel, remove axle stands and tighten
road wheel nuts to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)
20.Operate footbrake to locate brake pads before
driving vehicle.

51REAR AXLE AND FINAL DRIVE
6
REPAIRREV: 05/99 Refit
11.Clean stub axle and drive shaft and fit hub
assembly to axle.
12.Fit spacing washer.
13.Fit hub adjusting nut. Tighten to
50 Nm (37
lbf/ft).
Ensure hub is free to rotate with no
bearing play.
14.Back off adjusting nut 90°and tighten to
10 Nm
(7 lbf/ft).
15.Fit a new lock washer.
16.Fit locknut. Tighten to
50 Nm (37 lbf/ft).
17.Tab over lock washer to secure adjusting nut
and locknut.
18.Fit a new joint washer to driving member and fit
member to hub. Tighten bolts to
65 Nm (48
lbf/ft).
19.Fit circlip and dust cap.
20.Fit brake disc shield and brake caliper. Tighten
bolts to
82 Nm (61 lbf/ft).
21.Bleed brake systemSee BRAKES, Repair,
Brake system bleed
.
22.Fit road wheel, remove axle stands and tighten
road wheel nuts to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)
23.Operate footbrake to locate brake pads before
driving vehicle.

51REAR AXLE AND FINAL DRIVE
4
OVERHAUL
37.UsingLRT-51-500and pressLRT-99-002,
remove inner bearing cone from pinion.
INSPECTION
38.Examine all components for obvious wear or
damage.
39.Bearing cones must be a press fit on their
locations, except drive pinion flange and bearing
which is a slide fit.
40.The crown wheel and pinion are supplied as a
matched pair and must not be interchanged
separately. A new crown wheel and pinion
matched pair may be fitted to an original gear
carrier casing if sound. original crown wheel and
pinion, if sound, may be fitted into a replacement
casing.
41.The two parts of differential unit casing are
matched and must not be replaced separately.
42.Discard and renew all thrust washers.
43.Differential housings with worn thrust washer
seatings must be replaced as a pair.
44.Examine differential case to crown wheel joint
face for burrs and damage which could lead to
crown wheel run-out when fitted.ASSEMBLE
Differential
45.Fit differential lower wheel and thrust washer to
differential case. See illustration following
instruction 23.
46.Fit dished thrust washers.
47.Fit cross-shaft and pinions.
48.Fit differential upper wheel and thrust washer.
49.Fit differential upper case lining-up marks.
50.Secure assembly with bolts using Loctite
'Studlock' grade CVX on threads and tighten
evenly and diametrically to
95 Nm (70 lbf/ft).
51.Fit crown wheel to differential casing. Use Loctite
'Studlock' grade CVX on fixing bolt threads and
tighten to correct torque.
52.Press on differential roller bearing cones less
shim washers, usingLRT-51-504, and leave to
one side until required for instruction 96.
53.Fit bearing cups to differential.
54.Fit differential unit and bearings to gear carrier
casing, and rotate unit to centralize bearings. Do
not fit bearing caps.