wheel torque LAND ROVER DEFENDER 1996 User Guide

REAR AXLE AND FINAL DRIVE
1
SPECIFICATIONS, TORQUE REV: 05/99 TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
REAR AXLE
Pinion housing to axle case 41.......................................................................
Crown wheel to differential case 58................................................................
Differential bearing cap to pinion housing 90..................................................
Differential drive flange to drive shaft 47.........................................................
Bevel pinion nut 129........................................................................................
Lower link to axle 176......................................................................................
Pivot bracket ball joint to axle 176...................................................................

FRONT AXLE AND FINAL DRIVE
1
REPAIR REV: 05/99 FRONT AXLE ASSEMBLY
Service repair no - 54.10.01
Remove
WARNING: Remove and refit of axle
requires a further two persons to steady
axle when lowering or repositioning axle.
1.Support chassis front.
2.Remove road wheels.
3.Support axle weight with hydraulic jack.
4.Remove radius arms to chassis frame nuts.
5.Disconnect steering damper from track rod.
Using a extractor remove track rod links from
swivel pin arms.
6.Remove four nuts and bolts securing radius
arms to axle bracket.
7.Remove radius arms.
8.Remove bolts securing brake hose brackets .
Refit bolts to prevent oil leakage.
9.Remove bolts from brake calipers and tie to one
side.
10.Remove nuts and washers securing shock
absorbers to axle.
11.Disconnect drag link from swivel pin housing
arm.
12.Remove two nuts and bolts securing panhard
rod to axle bracket. Lift rod clear of axle.
13.Mark for reassembly drive shaft flanges.
Remove four nuts and bolts, tie propeller shaft to
one side.
14.Release axle ventilation pipe banjo and lower
axle assembly. Remove road springs.
15.Disconnect anti-roll bar link
See FRONT
SUSPENSION, Repair, Anti-roll bar ball
.
16.Remove axle assembly.
Refit
17.Position axle under vehicle, supporting left side
of axle, and fit anti-roll bar links
See FRONT
SUSPENSION, Repair, Anti-roll bar links
.
18.Fit propeller shaft. Tighten bolts to
47 Nm (35
lbf/ft).
19.Fit panhard rod to axle bracket. Tighten bolts to
88 Nm (65 lbf/ft).
20.Fit drag link to swivel pin arm. Tighten fixings to
40 Nm (30 lbf/ft).
21.Fit shock absorbers to axle.
22.Fit brake calipers. Tighten bolts to
82 Nm (60
lbf/ft).
23.Tighten upper swivel pin bolts to78 Nm (58
lbf/ft).
24.Fit radius arms to axle brackets. Tighten bolts to
197 Nm (145 lbf/ft).
25.Fit steering damper to track rod.
26.Fit radius arms to chassis side member. Tighten
fixings to
197 Nm (145 lbf/ft).
27.Tighten track rod end to40 Nm (30 lbf/ft)and fit
new split pin.
28.Remove chassis supports, fit road wheels and
tighten to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)

FRONT AXLE AND FINAL DRIVE
3
REPAIR REV: 05/99 Refit
11.Clean stub axle and drive shaft and fit hub
assembly to axle.
12.Fit spacing washer.
13.Fit hub adjusting nut. Tighten to
50 Nm (37
lbf/ft).
Ensure hub is free to rotate with no
bearing play.
14.Back off adjusting nut 90°and tighten to
10 Nm
(7 lbf/ft).
15.Fit a new lock washer.
16.Fit locknut. Tighten to
50 Nm (37 lbf/ft).
17.Tab over lock washer to secure adjusting nut
and locknut.
18.Fit a new joint washer to driving member and fit
member to hub. Tighten bolts to
65 Nm (48
lbf/ft).
19.Fit original drive shaft shim and secure with a
circlip.
20.To check drive shaft end play, mount a dial
gauge using bracketLRT-99-503and rest pin in
a loaded condition on end of drive shaft.
21.Fit a suitable bolt to threaded end of drive shaft.
Move drive shaft in and out noting dial gauge
reading. End play should be between 0,08 to
0,25 mm.
22.If end play requires adjustment, remove circlip,
measure shim thickness and fit an appropriate
shim to give required end-play.
23.Remove bolt from drive shaft, fit circlip and dust
cap.
24.Fit brake disc shield and brake caliper. Tighten
fixings to
82 Nm (60 lbf/ft).
25.Bleed brake systemSee BRAKES, Repair,
Brake system bleed
.
26.Fit road wheel, remove axle stands and tighten
road wheel nuts to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)
27.Operate footbrake to locate brake pads before
driving vehicle.

FRONT AXLE AND FINAL DRIVE
1
SPECIFICATIONS, TORQUE REV: 05/99 TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
FRONT AXLE
Hub driving member to hub 65*.......................................................................
Brake disc to hub 73.......................................................................................
Stub axle to swivel pin housing 65*.................................................................
Brake caliper to swivel pin housing 82............................................................
Upper swivel pin to swivel pin housing 78*.....................................................
Lower swivel pin to swivel pin housing 78*.....................................................
Oil seal retainer to swivel pin housing 11........................................................
Swivel bearing housing to axle case 73*.........................................................
Pinion housing to axle case 41.......................................................................
Crown wheel to differential housing 58...........................................................
Differential bearing cap to pinion housing 90..................................................
Differential drive flange to drive shaft 47.........................................................
Mudshield to bracket lower swivel pin 11........................................................
Bevel pinion nut 130........................................................................................
Draglink to hub arm 40....................................................................................
Panhard rod to axle bracket 88.......................................................................
Radius arm to axle 190....................................................................................
Radius arm to chassis side member 190.........................................................
NOTE: * These bolts to be coated with Loctite 270 prior to assembly.

STEERING
5
FAULT DIAGNOSIS REV: 05/99 Symptom :-
Steering excessively light/sensitive. Excessive
freeplay at steering wheel.
1.Are steering box adjustments correct?
NO -
See Adjustment, Power Steering Box.
WARNING: Adjustments of steering box
should not be required while in warranty
period. If box is within warranty, it must be
returned to manufacturer. No attempt must be
made to introduce backlash.
YES - Suspect worn panhard rod or radius arm
bushes. Check condition of ball joints and the
lower steering column shaft universal joints for
wear
See Repair, Lower Steering Shaft and
Universal Joints
.
Symptom :-
Steering vibration, road wheel shimmy - wobble.
Vibration through the steering linkage powerful
enough to induce high frequency oscillation of the
steering wheel, is generally caused by out of balance
road wheels. However there are a number of other
possible causes of this symptom which if severe, may
be described as shimmy or wobble. Regardless of the
terminology used by the owner/driver to describe the
symptoms, the following diagnostic checks should be
carried out in the order presented.
1.Check the tyres and balance of the road wheels
See GENERAL SPECIFICATION DATA,
Information, Wheels and Tyres
,See
WHEELS AND TYRES, Fault diagnosis, Fault
- Symptoms See WHEELS AND TYRES,
Repair, Wheel Balancing .
2.Check the steering hydraulic damper function
See Steering Damper.
3.Check steering column universal joints for wear
and correct alignment
See Repair, Lower
Steering Shaft and Universal Joints
.4.Check steering linkage ball joints for wear,
correct alignment and security, including steering
box and tie rod
See Steering Linkage Inspect
.
5.Check all front suspension rubbers for wear.
Check all fixing torques, including radius arm
bushes, panhard rod and anti-roll bar
See
FRONT SUSPENSION, Repair, Panhard Rod
,
See FRONT SUSPENSION, Repair, Radius
Arm
,See FRONT SUSPENSION, Repair,
Anti-Roll Bar
,See FRONT SUSPENSION,
Repair, Front Shock Absorber
.
6.Fit new radius arm bushes using NTC 6781. Fit
new nuts, bolts and washers.
7.If problem persists fit damper kit STC 288 - 90,
STC 290 - 110/130 (2 off front) and STC 289 -
90, STC 291 - 110 levelled, STC 292 - 110
unlevelled, STC 293 - 130 (2 off rear). Road test
vehicle.
8.Check the power steering box adjustments and
operation
See Overhaul, Power Steering Box.
9.Check the hub bearing end floats and determine
the condition of the hub bearings as applicable
See FRONT AXLE AND FINAL DRIVE, Repair,
Front Hub Assembly
.
10.Check the resistance and condition of the
swivels
See FRONT AXLE AND FINAL DRIVE,
Description and operation, Description
.
If problem is not diagnosed: Repeat checks
starting at 1.
11.Carry out a full steering geometry check
See
GENERAL SPECIFICATION DATA,
Information, Steering
.

57STEERING
8
FAULT DIAGNOSIS 4. DIRECTIONAL STABILITY
From 1. GENERAL STEERING:
1.Is directional stability concern when vehicle is
towing?
YES - Check towing/vehicle loading parameters
in Owner's Handbook.
NO - go to 3.
2.Is problem resolved?
YES - end
NO - continue.
3.Check condition of rear trailing link/chassis
bushes.
4.Is problem resolved?
YES - end
NO - continue.
5.Check condition of front and rear shock
absorbers. If necessary, change units in pairs,
side to side.
6.Is problem resolved?
YES - end
NO - continue.
7.Check steering damper
See Steering Damper
.
8.Is problem resolved?
YES - end
NO - continue.
9.Check wheel balance
10.Is problem resolved?
YES - end
NO - contact local technical office.POWER STEERING FLUID LEAKS
1.Is fluid level correct?
YES - go to 3.
NO - Refill or drain to correct level. Bleed
system, check for leaks
See Repair, Power
Steering System - Bleed.
2.Is problem resolved?
YES - end
NO - continue.
3.Are hoses or joints leaking? Check on full lock
with engine at 2000 rev/min.
YES - loosen and retorque joints.
NO - go to 6.
4.Does leak remain?
YES - change PAS pipe.
NO - end.
5.Does leak remain?
YES - suspect seal in component. Check and
replace as necessary.
NO - end.
6.Is oil escaping from filler cap?
YES - bleed system
See Repair, Power
Steering System - Bleed.
NO - go to 8.
7.Is oil still escaping from filler cap?
YES - go back to 1.
NO - end.
8.Is oil leaking from PAS pump?
YES - go to 10.
NO - continue.
9.Is oil leaking from PAS box?
YES - go to 10.
NO - end.
10.Clean unit, add tracer dye to system. Retest
11.Is oil still leaking?
YES - establish leak point. Repair or replace unit
as necessary.
NO - end.

STEERING
11
FAULT DIAGNOSIS STIFF STEERING CHECKLIST
NOTE: Having completed visual checks
and steering assessment and confirmed
that vehicle steering load is incorrect carry
out the following procedure in order shown.
Steering wheel 'torque to turn' loads
1.Raise vehicle so both front wheels free.
2.With engine off, centralise steering wheel, and
remove steering wheel decal. Using torque
wrench on column nut, check torque required to
turn the steering wheel one turn in each
direction.
3.Record readings obtained in each direction.
Reading should be
4.40 Nm (3.5 lbf/ft).
NOTE: If figures are in excess of that
specified carry out steering box tie bar
reset below. If figures are as specified
See
Visual Check and Basic Adjustments
.
Steering box tie bar reset
1.Loosen the tie bar fixings one complete turn.
2.Drive vehicle carefully a short distance (within
the dealership) applying full lock in both
directions in order to settle steering components.
Drive vehicle over speed bumps and include
harsh braking if possible.
WARNING: Do not drive on public
highway.
3.Near end of operation 2. ensure vehicle is driven
in a straight line on level ground and halted.
4.Tighten panhard rod mounting arm nut to
110
Nm (81 lbf/ft).
5.Tighten the 2 fixings, tie bar to steering box, to
81 Nm (60 lbf/ft).
6.Recheck steering wheel torque to turn. If torque
reading is still greater than specified, carry out
steering shaft universal joint lubrication.Lower steering shaft universal joint lubrication
1.Check lower steering shaft is correctly phased
See Repair, Lower Steering Shaft and
Universal Joints
.
2.Lubricate universal joints with an anti-seizure
type penetrating spray. Work the joints to ensure
full penetration of the spray by driving vehicle
and steering from lock to lock.
3.If steering stiffness still persists carry out swivel
pin preload setting.
Swivel pin preload setting
1.The swivel pin preload setting must be checked
and set
See FRONT AXLE AND FINAL DRIVE,
Overhaul, Front Stub Axle, Constant Velocity
Joint and Swivel Pin Housing
.
Note that a pull load of 1.16 - 1.46 kg is required
after the axle shaft and swivel housing seal have
been removed.
Steering box adjustment
1.Check steering box adjustment
See
Adjustment, Power Steering Box
.
Steering damper check
1.Check condition of steering damper
See
Steering Damper
.

57STEERING
12
FAULT DIAGNOSISREV: 05/99 VISUAL CHECK AND BASIC ADJUSTMENTS
NOTE: It is important that the following
instructions are carried out in the
sequence shown and the results recorded.
1.Road springs - check that road springs are
correctly seated and are to correct specification
for vehicle. For spring specification
See
GENERAL SPECIFICATION DATA,
Information, Road Spring Data
.
2.Ride height - measure trim height from wheel
centre to wheelarch eyebrow. Record results on
data sheet.
3.Check/top up power steering fluid
See Repair,
Power Steering Fluid Reservoir
.
4.Check tension and condition of drive belt
See
ELECTRICAL, Repair, Auxiliary drive belt
.
5.Track rod/drag link - check condition of track rod,
drag link and ball joints
See Repair, Drag Link
and Drag Link Ends
.
If either component is damaged, check operation
of steering damper and steering box for
smoothness. Replace all damaged or worn
components that impair the operation of the
steering system.
6.Suspension bushes - examine all steering and
suspension bushes for signs of wear and
deterioration. Also check all fixings for torque
relaxation. Tighten to correct torque value
See
FRONT SUSPENSION, Specifications, torque,
Torque Values
.
7.Oil leaks - check front and rear axle hubs for
leak and repair as necessary.
8.Brake system - check brake system for leaks,
pipe condition, pad wear/contamination, disc
wear/condition.
9.Hub end float - check movement in the hubs by
rocking the wheels.
10.Check front wheel alignment. Vehicles displaying
a tendency to veer more than considered
allowable, it is permissible to set the front track
to parallel.11.Having completed all the above checks and
adjustments, road test vehicle
See Road Test
Procedure
.
Attempt to reproduce the symptoms established
earlier. If symptoms still exist refer to relevant
Diagnostic Chart.
STEERING LINKAGE INSPECT
NOTE: When inspecting steering linkages
and ball joints for wear the following items
must be checked.
Steering ball joints
1.Check ball joint rubber boots for security, signs
of cracking or deterioration.
2.Check ball joint assemblies for seizure i.e. no
movement on ball joint and associated
assemblies.
3.Check for excessive wear. This will be evident
as extreme movement on track rod and steering
linkages. Renew parts as necessary
See
Repair, Track Rod and Linkage
,See Repair,
Drag Link and Drag Link Ends
.
Steering linkages
1.Check all linkages for wear, deterioration and
damage. Renew parts as necessary
See
Repair, Track Rod and Linkage
,See Repair,
Drag Link and Drag Link Ends
.

STEERING
1
ADJUSTMENT POWER STEERING BOX - ADJUST
Service repair no - 57.35.01
WARNING: Adjustments of steering box
should not be required while in warranty
period. If box is stiff or tight and within
warranty, it must be returned to manufacturer. No
attempt must be made to introduce backlash.
1.Apply park brake brake, chock wheels and Jack
up front of vehicle until wheels are clear of
ground.
2.Support chassis front on axle stands.
3.Disconnect drag link from steering drop arm.
4.Check torque to turn
See Fault diagnosis,
Stiff Steering Checklist
.
5.Centralise steering box
See Centralise
Steering Box
.
NOTE: Only check for no backlash when
steering box is in central position.
NOTE: If steering wheel is not straight, it
should be repositioned
See Repair,
Steering Wheel
.
6.Adjustment is obtained by rocking the drop arm
about centre whilst an assistant slowly tightens
the steering box adjuster screw.
7.Tighten locknut when all backlash has been
removed.8.Repeat the check for backlash. If backlash exists
loosen locknut and repeat adjustment
procedure.
9.Turn steering wheel lock to lock and check no
tightness exists.
10.Ensure front wheels are aligned and in straight
ahead position.
11.Adjust drag link 924 mm between ball joint
centres.
12.Connect drag link and tighten to
40 Nm (30
lbf/ft).
13.Lower vehicle to ground level and remove
chocks.
14.Road test vehicle
See Fault diagnosis, Road
Test Procedure
.
Drag link adjust
1.RH drive vehicles - if steering wheel is to right,
drag link is too long. If steering wheel is to left
drag link is too short.
LH drive vehicles - if steering wheel is to right,
drag link is too short. If steering wheel is to left
drag link is too long.
2.Adjust drag link until steering wheel points
straight ahead when vehicle is travelling in a
straight line.
CENTRALISE STEERING BOX
Service repair no - 57.35.05
LH drive vehicle
1.Disconnect drag link from drop arm
See Repair,
Drag link and drag link ends
.
2.Turn steering wheel on full RH lock.
3.Turn steering wheel back exactly two turns.
4.Fit drag link
See Repair, Drag link and drag
link ends
.
RH drive vehicle
1.Repeat operation for LH drive vehicle but turn
steering wheel on full LH lock.

STEERING
5
REPAIR REV: 05/99
23.Fit panhard rodSee FRONT SUSPENSION,
Repair, Panhard rod
.
24.Fit road wheels. Lower vehicle to ground and
tighten wheel nuts to correct torque:
Alloy wheels - 130 Nm (96 lbf/ft)
Steel wheels - 100 Nm (80 lbf/ft)
Heavy duty wheels - 170 Nm (125 lbf/ft)
25.Remove plugs and refit feed and return pipes to
steering box. Tighten 16mm thread to
20 Nm (15
lbf/ft),
14mm thread to15 Nm (11 lbf/ft).
26.Remove filler cap. Fill reservoir to oil level mark
on dipstick, using recommended fluid
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended lubricants and
fluids
.
27.Bleed power steering system
See Power
steering system - bleed
.
28.Recheck fluid level and replace cap.
29.With engine running, test steering system for
leaks by holding steering in both full lock
directions.
CAUTION: Do not maintain this pressure
for more than 30 seconds in any one
minute, to avoid oil overheating and
possible seal damage.
30.Test drive vehicle: using both full lock directions,
to settle steering components. If possible, drive
vehicle over uneven ground and include harsh
braking.
WARNING: Do not test drive vehicle on
public highway.
31.Drive vehicle in a straight line on level ground
and stop.
32.Tighten tie bar to mounting nut to
110 Nm (81
lbf/ft).
33.Tighten tie bar to steering box fixings to81 Nm
(60 lbf/ft).
34.Ensure steering wheel is correctly aligned when
wheels are positioned straight ahead.
35.If necessary, reposition steering wheel
See
Steering wheel
.
36.Road test vehicle.