warning LAND ROVER DEFENDER 1996 Owner's Guide

FRONT AXLE AND FINAL DRIVE
1
REPAIR REV: 05/99 FRONT AXLE ASSEMBLY
Service repair no - 54.10.01
Remove
WARNING: Remove and refit of axle
requires a further two persons to steady
axle when lowering or repositioning axle.
1.Support chassis front.
2.Remove road wheels.
3.Support axle weight with hydraulic jack.
4.Remove radius arms to chassis frame nuts.
5.Disconnect steering damper from track rod.
Using a extractor remove track rod links from
swivel pin arms.
6.Remove four nuts and bolts securing radius
arms to axle bracket.
7.Remove radius arms.
8.Remove bolts securing brake hose brackets .
Refit bolts to prevent oil leakage.
9.Remove bolts from brake calipers and tie to one
side.
10.Remove nuts and washers securing shock
absorbers to axle.
11.Disconnect drag link from swivel pin housing
arm.
12.Remove two nuts and bolts securing panhard
rod to axle bracket. Lift rod clear of axle.
13.Mark for reassembly drive shaft flanges.
Remove four nuts and bolts, tie propeller shaft to
one side.
14.Release axle ventilation pipe banjo and lower
axle assembly. Remove road springs.
15.Disconnect anti-roll bar link
See FRONT
SUSPENSION, Repair, Anti-roll bar ball
.
16.Remove axle assembly.
Refit
17.Position axle under vehicle, supporting left side
of axle, and fit anti-roll bar links
See FRONT
SUSPENSION, Repair, Anti-roll bar links
.
18.Fit propeller shaft. Tighten bolts to
47 Nm (35
lbf/ft).
19.Fit panhard rod to axle bracket. Tighten bolts to
88 Nm (65 lbf/ft).
20.Fit drag link to swivel pin arm. Tighten fixings to
40 Nm (30 lbf/ft).
21.Fit shock absorbers to axle.
22.Fit brake calipers. Tighten bolts to
82 Nm (60
lbf/ft).
23.Tighten upper swivel pin bolts to78 Nm (58
lbf/ft).
24.Fit radius arms to axle brackets. Tighten bolts to
197 Nm (145 lbf/ft).
25.Fit steering damper to track rod.
26.Fit radius arms to chassis side member. Tighten
fixings to
197 Nm (145 lbf/ft).
27.Tighten track rod end to40 Nm (30 lbf/ft)and fit
new split pin.
28.Remove chassis supports, fit road wheels and
tighten to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)

STEERING
5
FAULT DIAGNOSIS REV: 05/99 Symptom :-
Steering excessively light/sensitive. Excessive
freeplay at steering wheel.
1.Are steering box adjustments correct?
NO -
See Adjustment, Power Steering Box.
WARNING: Adjustments of steering box
should not be required while in warranty
period. If box is within warranty, it must be
returned to manufacturer. No attempt must be
made to introduce backlash.
YES - Suspect worn panhard rod or radius arm
bushes. Check condition of ball joints and the
lower steering column shaft universal joints for
wear
See Repair, Lower Steering Shaft and
Universal Joints
.
Symptom :-
Steering vibration, road wheel shimmy - wobble.
Vibration through the steering linkage powerful
enough to induce high frequency oscillation of the
steering wheel, is generally caused by out of balance
road wheels. However there are a number of other
possible causes of this symptom which if severe, may
be described as shimmy or wobble. Regardless of the
terminology used by the owner/driver to describe the
symptoms, the following diagnostic checks should be
carried out in the order presented.
1.Check the tyres and balance of the road wheels
See GENERAL SPECIFICATION DATA,
Information, Wheels and Tyres
,See
WHEELS AND TYRES, Fault diagnosis, Fault
- Symptoms See WHEELS AND TYRES,
Repair, Wheel Balancing .
2.Check the steering hydraulic damper function
See Steering Damper.
3.Check steering column universal joints for wear
and correct alignment
See Repair, Lower
Steering Shaft and Universal Joints
.4.Check steering linkage ball joints for wear,
correct alignment and security, including steering
box and tie rod
See Steering Linkage Inspect
.
5.Check all front suspension rubbers for wear.
Check all fixing torques, including radius arm
bushes, panhard rod and anti-roll bar
See
FRONT SUSPENSION, Repair, Panhard Rod
,
See FRONT SUSPENSION, Repair, Radius
Arm
,See FRONT SUSPENSION, Repair,
Anti-Roll Bar
,See FRONT SUSPENSION,
Repair, Front Shock Absorber
.
6.Fit new radius arm bushes using NTC 6781. Fit
new nuts, bolts and washers.
7.If problem persists fit damper kit STC 288 - 90,
STC 290 - 110/130 (2 off front) and STC 289 -
90, STC 291 - 110 levelled, STC 292 - 110
unlevelled, STC 293 - 130 (2 off rear). Road test
vehicle.
8.Check the power steering box adjustments and
operation
See Overhaul, Power Steering Box.
9.Check the hub bearing end floats and determine
the condition of the hub bearings as applicable
See FRONT AXLE AND FINAL DRIVE, Repair,
Front Hub Assembly
.
10.Check the resistance and condition of the
swivels
See FRONT AXLE AND FINAL DRIVE,
Description and operation, Description
.
If problem is not diagnosed: Repeat checks
starting at 1.
11.Carry out a full steering geometry check
See
GENERAL SPECIFICATION DATA,
Information, Steering
.

57STEERING
10
FAULT DIAGNOSISREV: 05/99 VISUAL AND SAFETY CHECKS
WARNING: Before taking vehicle out on
the public highway for road test, it is
important that the following basic visual
checks are carried out to ensure that the vehicle
complies with legal requirements.
Tyres and wheel rims
1.Check and adjust tyre pressures
See
GENERAL SPECIFICATION DATA,
Information, Tyre Pressures
.
Note that this information refers to standard tyres
fitted as original equipment.
2.Check condition of tyres. Inspect for signs of
uneven wear, damage and feathering. Check
tread depth.
3.Ensure that the tyre make, type and general
condition are common across each axle.
4.Check wheel rims for signs of damage and
excessive run out.
5.Carry out road test
See Road Test Procedure
.
ROAD TEST PROCEDURE
General steering/handling problems can usually be
classified into one of the categories listed and ARE
GENERALLY RELATED TO THE AGE, CONDITION
AND USE OF THE VEHICLE.
WARNING: Ensure that all road tests are
conducted by suitably qualified drivers in
a safe and legal manner, and where local
traffic conditions allow.
1.Carry out visual and safety checks
See Visual
and Safety Checks
.
Confirm general nature of complaint with customer,
simulating where possible the conditions under which
the problem occurs. Carry out following road test
procedure to establish the problem.2.Steering load assessment - drive at 16 km/h (10
mph). Put 90°turn input into steering wheel,
check self centering. The self centering should
be equal on each lock but not necessarily return
to exactly straight ahead without assistance from
the driver.
3.Steering assessment - drive at 64 km/h (40 mph)
on a staight FLAT road (no camber), check for
steering veer. The vehicle should follow a
straight path with NO tendency to follow a
curved path. If vehicle veers towards the kerb,
vehicle may be 'camber sensitive'. A small
amount of veer in direction of camber is
acceptable.
4.Directional stability assessment - drive at 112
km/h (70 mph) or maximum legal speed on a
straight flat road. Carry out a normal lane
change. Vehicle should quickly settle into a new
straight path.
5.Braking assessment (medium effort) - drive at 96
km/h (60 mph) on a straight flat road. Apply
steady medium braking effort, noting any
tendency to veer. Carry out brake test three
times, if a veer is consistently noted carry out a
braking efficiency test on a rolling road.
6.Braking assessment (full effort) - drive at 96
km/h (60 mph) on a straight flat road. Apply full
braking effort, noting any tendency to veer. Carry
out brake test three times, if a veer is
consistently noted carry out a braking efficiency
test on a rolling road.
If the symptom described by the customer is stiff
steering or steering niggle, carry out stiff steering
procedure
See Stiff Steering Checklist.
If not, proceed with basic checks and adjustments
See Visual Check and Basic Adjustments.

STEERING
11
FAULT DIAGNOSIS STIFF STEERING CHECKLIST
NOTE: Having completed visual checks
and steering assessment and confirmed
that vehicle steering load is incorrect carry
out the following procedure in order shown.
Steering wheel 'torque to turn' loads
1.Raise vehicle so both front wheels free.
2.With engine off, centralise steering wheel, and
remove steering wheel decal. Using torque
wrench on column nut, check torque required to
turn the steering wheel one turn in each
direction.
3.Record readings obtained in each direction.
Reading should be
4.40 Nm (3.5 lbf/ft).
NOTE: If figures are in excess of that
specified carry out steering box tie bar
reset below. If figures are as specified
See
Visual Check and Basic Adjustments
.
Steering box tie bar reset
1.Loosen the tie bar fixings one complete turn.
2.Drive vehicle carefully a short distance (within
the dealership) applying full lock in both
directions in order to settle steering components.
Drive vehicle over speed bumps and include
harsh braking if possible.
WARNING: Do not drive on public
highway.
3.Near end of operation 2. ensure vehicle is driven
in a straight line on level ground and halted.
4.Tighten panhard rod mounting arm nut to
110
Nm (81 lbf/ft).
5.Tighten the 2 fixings, tie bar to steering box, to
81 Nm (60 lbf/ft).
6.Recheck steering wheel torque to turn. If torque
reading is still greater than specified, carry out
steering shaft universal joint lubrication.Lower steering shaft universal joint lubrication
1.Check lower steering shaft is correctly phased
See Repair, Lower Steering Shaft and
Universal Joints
.
2.Lubricate universal joints with an anti-seizure
type penetrating spray. Work the joints to ensure
full penetration of the spray by driving vehicle
and steering from lock to lock.
3.If steering stiffness still persists carry out swivel
pin preload setting.
Swivel pin preload setting
1.The swivel pin preload setting must be checked
and set
See FRONT AXLE AND FINAL DRIVE,
Overhaul, Front Stub Axle, Constant Velocity
Joint and Swivel Pin Housing
.
Note that a pull load of 1.16 - 1.46 kg is required
after the axle shaft and swivel housing seal have
been removed.
Steering box adjustment
1.Check steering box adjustment
See
Adjustment, Power Steering Box
.
Steering damper check
1.Check condition of steering damper
See
Steering Damper
.

STEERING
1
ADJUSTMENT POWER STEERING BOX - ADJUST
Service repair no - 57.35.01
WARNING: Adjustments of steering box
should not be required while in warranty
period. If box is stiff or tight and within
warranty, it must be returned to manufacturer. No
attempt must be made to introduce backlash.
1.Apply park brake brake, chock wheels and Jack
up front of vehicle until wheels are clear of
ground.
2.Support chassis front on axle stands.
3.Disconnect drag link from steering drop arm.
4.Check torque to turn
See Fault diagnosis,
Stiff Steering Checklist
.
5.Centralise steering box
See Centralise
Steering Box
.
NOTE: Only check for no backlash when
steering box is in central position.
NOTE: If steering wheel is not straight, it
should be repositioned
See Repair,
Steering Wheel
.
6.Adjustment is obtained by rocking the drop arm
about centre whilst an assistant slowly tightens
the steering box adjuster screw.
7.Tighten locknut when all backlash has been
removed.8.Repeat the check for backlash. If backlash exists
loosen locknut and repeat adjustment
procedure.
9.Turn steering wheel lock to lock and check no
tightness exists.
10.Ensure front wheels are aligned and in straight
ahead position.
11.Adjust drag link 924 mm between ball joint
centres.
12.Connect drag link and tighten to
40 Nm (30
lbf/ft).
13.Lower vehicle to ground level and remove
chocks.
14.Road test vehicle
See Fault diagnosis, Road
Test Procedure
.
Drag link adjust
1.RH drive vehicles - if steering wheel is to right,
drag link is too long. If steering wheel is to left
drag link is too short.
LH drive vehicles - if steering wheel is to right,
drag link is too short. If steering wheel is to left
drag link is too long.
2.Adjust drag link until steering wheel points
straight ahead when vehicle is travelling in a
straight line.
CENTRALISE STEERING BOX
Service repair no - 57.35.05
LH drive vehicle
1.Disconnect drag link from drop arm
See Repair,
Drag link and drag link ends
.
2.Turn steering wheel on full RH lock.
3.Turn steering wheel back exactly two turns.
4.Fit drag link
See Repair, Drag link and drag
link ends
.
RH drive vehicle
1.Repeat operation for LH drive vehicle but turn
steering wheel on full LH lock.

STEERING
5
REPAIR REV: 05/99
23.Fit panhard rodSee FRONT SUSPENSION,
Repair, Panhard rod
.
24.Fit road wheels. Lower vehicle to ground and
tighten wheel nuts to correct torque:
Alloy wheels - 130 Nm (96 lbf/ft)
Steel wheels - 100 Nm (80 lbf/ft)
Heavy duty wheels - 170 Nm (125 lbf/ft)
25.Remove plugs and refit feed and return pipes to
steering box. Tighten 16mm thread to
20 Nm (15
lbf/ft),
14mm thread to15 Nm (11 lbf/ft).
26.Remove filler cap. Fill reservoir to oil level mark
on dipstick, using recommended fluid
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended lubricants and
fluids
.
27.Bleed power steering system
See Power
steering system - bleed
.
28.Recheck fluid level and replace cap.
29.With engine running, test steering system for
leaks by holding steering in both full lock
directions.
CAUTION: Do not maintain this pressure
for more than 30 seconds in any one
minute, to avoid oil overheating and
possible seal damage.
30.Test drive vehicle: using both full lock directions,
to settle steering components. If possible, drive
vehicle over uneven ground and include harsh
braking.
WARNING: Do not test drive vehicle on
public highway.
31.Drive vehicle in a straight line on level ground
and stop.
32.Tighten tie bar to mounting nut to
110 Nm (81
lbf/ft).
33.Tighten tie bar to steering box fixings to81 Nm
(60 lbf/ft).
34.Ensure steering wheel is correctly aligned when
wheels are positioned straight ahead.
35.If necessary, reposition steering wheel
See
Steering wheel
.
36.Road test vehicle.

57STEERING
16
REPAIR 15.Centralise steering box
See Adjustment,
Centralise steering box
.
16.Align steering wheel, if necessary.
CAUTION: A drag link that is damaged or
bent must be renewed. DO NOT attempt
repair.
17.Fit drag link to swivel housing arms and tighten
nuts to
40 Nm (30 lbf/ft).Fit new split pins.
18.Ensure full steering travel is obtained between
lock stops
See Adjustment, Steering lock
stops
. Adjust drag link length to suit.
19.Tap ball joints in direction shown so both pins
are in same angular plane.
20.Tighten clamp bolts to
14 Nm (10 lbf/ft).
21.Refit road wheel and remove axle stands or
vehicle from ramp.
22.Road test vehicle.
23.If driving straight ahead and steering wheel is
offset by 0°±5°in either direction, correct by
adjusting drag link length.
WARNING: To correct steering wheel
deviations greater than±5°remove and
reposition steering wheel
See Steering
wheel
.

STEERING
1
OVERHAUL POWER STEERING BOX - ADWEST
Service repair no - 57.10.07
Overhaul
NOTE: Overhaul of steering box should
not be carried out during the warranty
period.
WARNING: Wear safety glasses while
removing and refitting circlips and
retaining ring.
CAUTION: Absolute cleanliness is
essential when overhauling power steering
box.
1.Remove steering box from vehicleSee Repair,
Power Steering Box
. Mark drop arm and
steering box for realignment on assembly.
Remove drop arm using extractorLRT-57-012.
Loosen drop arm securing nut, but do not
remove before using extractor. Remove dirt
excluder from output shaft.
2.Drain oil, remove blanking plugs and bleed
screw. Hold steering box over suitable container,
turn input shaft from lock to lock, until oil is
drained. Refit bleed screw.
3.Rotate retainer ring until one end is 12 mm from
extractor hole. Using a drift through hole in
cylinder, lift retaining ring from groove in cylinder
bore.
4.Remove retainer ring, using a screwdriver.
5.Turn input shaft (left lock on left hand drive, right
lock on right hand drive) until piston pushes out
cover. Turn input shaft fully in opposite direction,
applying pressure to piston.
6.Remove set screw retaining rack pad adjuster.
7.Remove rack adjuster and pad.
8.Remove sector shaft adjuster locknut.
9.Remove four bolts from sector shaft cover.
10.Screw in sector shaft adjuster until cover is
removed.
NOTE: Sealant is applied to hexagon
socket to 'tamperproof' sector shaft
adjuster.
11.Slide out sector shaft.

FRONT SUSPENSION
1
REPAIR SELF LOCKING NUTS
WARNING: Where self locking nuts are
removed, they must be replaced with new
nuts of same specification.
PANHARD ROD
Service repair no - 60.10.07.
Remove
1.Remove fixings at mounting arm.
2.Remove fixings at axle bracket.
3.Remove panhard rod.
4.Using a suitable length of steel tubing, press out
flexible bushes. Ensure tubing locates on outer
edge of bush and not on rubber inner.
Refit
5.Fit replacement bushes.
CAUTION: Apply pressure to outer edge of
bush, and not rubber inner.
6.Fit panhard rod to axle bracket and mounting
arm. Tighten fixings to
88 Nm (65 lbf/ft).
RADIUS ARM
Service repair no - 60.10.16.
Remove
1.Loosen road wheel retaining nuts.
2.Raise front of vehicle. Support chassis on stands
and remove wheel.
3.Support front axle weight with jack.
4.Remove radius arm to chassis side member
fixings.
5.Disconnect track rod at ball joint.

REAR SUSPENSION
5
REPAIR ANTI-ROLL BAR LINKS
Service repair no - 64.35.24.
Remove
1.Remove 2 nuts, bolts, washers and rubber
bushes from links and lower anti-roll bar to clear
links.
2.Remove cotter pin and loosen castellated nut a
few turns.
3.Release link using special tool18G 1063Aas
shown.
4.Remove castellated nut and remove link.
Refit
5.Fit anti-roll bar link arm and castellated nut. Point
link arm down as shown. Tighten fixing to
40 Nm
(30 lbf/ft)
and fit new cotter pin.
6.Align anti-roll bar to links.
7.Fit bolts, washers and rubber bushes using new
self locking nuts and secure anti-roll bar to links.
Tighten to
68Nm (50 lbf/ft).
SELF LEVELLING UNIT
Service repair no - 64.30.09
Remove
WARNING: The levelling unit contains
pressurised gas and MUST NOT be
dismantled. Repair is by replacement of
complete unit only.
1.Raise and support the vehicle under chassis and
use a jack to support weight of the axle.
2.Disconnect upper links at pivot bracket.
3.Ease up levelling unit lower gaiter and unscrew
lower ball joint at push rod using thin jawed
spanners.
4.Release webbing strap from the chassis.
5.Remove 4 nuts securing top bracket to chassis
and withdraw levelling unit complete with
bracket.
Renew levelling unit ball joints
The ball joints for the levelling unit may be dismantled
for cleaning and examination.
6.Unscrew lower ball joint from pivot bracket.
7.Unscrew ball joint from top bracket.
8.Reassemble ball joints, packing with
Dextagrease G.P. or equivalent. Renew joints if
worn.
9.Check condition of gaiters and renew if
necessary.