light LAND ROVER DEFENDER 1996 Service Manual

ELECTRICAL
21
REPAIR MAIN LIGHT SWITCH
Service repair no - 86.65.10
Remove
1.Remove steering column nacelle
See
STEERING, Repair, Steering column nacelle.
2.Disconnect main light switch multi-plug from
main harness.
3.Slacken locknut and release light switch from
slot in mounting bracket.
Refit
4.Fit light switch in mounting bracket.
5.Reconnect switch multi-plug.
6.Fit steering column nacelle
See STEERING,
Repair, Steering column nacelle.
HEATED REAR SCREEN, REAR FOG LAMP AND
HAZARD WARNING SWITCHES
Service repair no - 86.65.36 - Heated rear screen
Service repair no - 86.65.65 - Rear fog lamp
Service repair no - 86.65.50 - Hazard warning
Remove
1.Remove 2 screws and withdraw switch panel
from lower fascia.
2.Disconnect multi-plug from rear of switch.
3.On hazard warning switch only, remove 2
separate leads.
4.Press in spring retainers and withdraw switch
from switch panel.
Refit
5.Fit new switch into switch panel.
6.Reconnect switch multi-plug, and leads if
applicable.
7.Fit switch panel to lower fascia.

86ELECTRICAL
22
REPAIR CIGAR LIGHTER
Service repair no - 86.65.60
Remove
1.Remove 2 screws and withdraw switch panel
from lower fascia.
2.Disconnect electrical leads from switch housing,
including illumination bulb.
3.Release 2 retaining tags and remove bulb holder
from switch housing.
4.Remove cigar lighter from switch housing.
5.Press in retaining tags and withdraw housing
from switch panel.
Refit
6.Fit housing to switch panel.
7.Fit bulb holder to switch housing.
8.Connect electrical leads and illumination bulb.
9.Insert cigar lighter into switch housing.
10.Fit switch panel to lower fascia.REAR SCREEN WIPER/WASHER SWITCH
Service repair no - 84.35.34
Remove1.Remove 2 screws and withdraw switch panel
from lower fascia.
2.Disconnect electrical leads from rear screen
wiper/washer switch.
3.Insert a small screwdriver in base of switch
knob, press in retaining lug, and remove knob
from switch spindle.
4.Unscrew locking ring, with wavy washer, and
withdraw wiper/washer switch from panel.
Refit
5.Fit switch to switch panel.
6.Press in retaining lug and fit knob onto switch
spindle.
7.Connect electrical leads to switch.
8.Fit switch panel.

INSTRUMENTS
3
REPAIR CLOCK - CENTRE DASH PANEL
Service repair no - 88.15.07
Remove
1.Remove 2 screws and withdraw switch panel
from centre dash.
2.Release illumination bulb holder and disconnect
electrical leads from clock.
3.Press in spring retainers and remove clock from
panel.
Refit
4.Fit clock into dash panel.
5.Fit electrical leads and bulb holder.
6.Secure switch panel to centre dash.WARNING LIGHT PANEL
Service repair no - 88.20.18
Remove
1.Remove 2 screws and withdraw warning light
panel.
2.Disconect both multi-plugs.
3.Disconnect illumination bulb leads.
4.Remove warning light panel.
Refit
5.Fit illumination bulb leads and multi-plugs to
warning light panel.
6.Secure warning light panel to instrument panel.

88INSTRUMENTS
4
REPAIR PRINTED CIRCUIT - WARNING LIGHT PANEL
Service repair no - 88.20.20
Remove
1.Remove warning light panel
See Warning light
panel
.
2.Remove 13 illumination bulb holders from light
panel.
3.Release printed circuit from locating pins and
remove from panel seatings.
Refit
4.Fit new printed circuit over panel seatings and
position on locating pins.
5.Fit illumination bulbs to secure circuit.
6.Fit warning light panel
See Warning light
panel
.FUEL GAUGE TANK UNIT - REAR FUEL TANK,
110/130
Service repair no - 88.25.30
WARNING: Ensure that fuel handling
precautions given in Section 01 -
Introduction are strictly adhered to when
carrying out the following instructions.
Remove
1.Disconnect battery.
2.Remove fuel filler cap.
3.Remove tank drain plug, allow fuel to drain into a
clean container, and refit plug.
4.On LH side of tank, disconnect fuel supply pipe
from outlet pipe on fuel gauge unit.
5.Disconnect electrical plug from fuel gauge unit.
6.Release locking ring and withdraw fuel gauge
unit from tank, complete with sealing ring.
Refit
7.Insert gauge unit into tank with float positioned to
base of tank. Fit new sealing washer, if
necessary.
8.Secure gauge unit with locking ring.
9.Fit electrical plug and reconnect fuel supply pipe.
10.Refill fuel tank.
11.Reconnect battery.