battery LAND ROVER DEFENDER 1999 Repair Manual

PANEL REPAIRS
3
REPAIR WHEEL ARCH - FRONT
Remove
The procedure to change the Inner Front Wheelarch is
the same as for the Wing Upper, except for removal of
the ABS sensors and shield, if fitted.
BULKHEAD ASSEMBLY
Remove
1.Disconnect both battery leads, negative lead
first.
2.Remove front lower wing.See this Section.
3.Remove RH and LH front upper wing.See this
Section.
4.Remove headlamp mounting panels.See this
Section.
5.Remove screen aperture.See this Section.
6.Remove both front doors.
7.Remove lower fascia panel.See CHASSIS
AND BODY, Repair.
8. Models with A/C:Remove relevant A/C pipes.
9.Remove front grille.
10.Drain cooling system.See COOLING
SYSTEM, Adjustment.
11.Remove radiator and intercooler.
12. Models with A/C:Remove condensor.
13.Remove air cleaner assembly.
14.Remove heater unit.See HEATING AND
VENTILATION, Repair.
15.Remove brake servo assembly.
16.Remove heater ducts.
17.Remove both front seats.
18.Remove front carpets.
19.Release all relevant harnesses and position
aside.
20.Remove facia support bracket.
Refit
21.Prepare and clean panel joint faces. Ensure all
necessary grommets and sealant is applied to
new bulkhead.
22.Reverse removal procedure.
23.Bleed brake system.See BRAKES,
Adjustment.
24.Align headlamps.See ELECTRICAL,
Adjustment.
25.Water test after refitting.
ProCarManuals.com

77PANEL REPAIRS
4
REPAIR SCREEN APERTURE
Remove
1.Disconnect both battery leads, negative lead
first.
2.Raise side of vehicle.
3.Remove front and centre headlining sections.
4.Remove both’A’post upper trims.
5.Remove front door aperture seals.
6.Release upper front corner of rear door aperture
seal.
7.Remove both wiper arms.See WIPERS AND
WASHERS, Repair.
8.Remove front screen.
9.Remove all roof fixings, back to the’B/C’post.
10.Release sealant securing front edge of roof.
11.Insert wedges into top of both’B/C’posts. This
will allow access for removal of screen aperture.
12.With assistance remove screen aperture.Refit
13.Prepare and clean panel joint faces.
14.Reverse removal procedure. Fit new foam seal
to top edge of aperture.
NOTE: When refitting, ensure screen
aperture is correctly fitted onto location
pins in bulkhead.
15.When applying sealant to top edge of aperture,
the correct colour sealant must be used, see
note below.
NOTE: White roof vehicles use a white
sealant. Coloured roof vehicles use a
black sealant.
ProCarManuals.com

PANEL REPAIRS
5
REPAIR SILL - FRONT
Remove
NOTE: The procedure to replace the rear
sill section is the same as the front.
1.Remove bolts securing sill to body, discard seal.
Refit
NOTE: Front sill
NOTE: Rear sill
2.Prepare and clean panel joint faces. Refit new
seal.
3.Reverse removal procedure.’B/C’&’D’POST
Remove
1.Disconnect both battery leads, negative lead
first.
2.Remove rear door and striker.
3.Remove front seat belt reel.See CHASSIS
AND BODY, Repair.
4.Remove front and rear carpets.
5.Remove front seat.
6.Remove rear seat.
7.Remove front, centre and rear sections of
headlining.
NOTE: Assembly is held on with bolts.
Refit
8.Prepare and clean panel joint faces.
9.Reverse removal procedure.
ProCarManuals.com

77PANEL REPAIRS
6
REPAIR CORNER CAPPING
The Corner Capping is not replaced as a single panel.
It is replaced in conjunction with either the Body Side
Lower Panel or Body Side Assembly. The procedure
to replace the Corner Capping is shown in the Body
Side Lower Panel procedure.
BODY SIDE CAPPING
The Body Side Capping is not replaced as a single
panel. It is replaced in conjunction with either the
Body Side Lower Panel or Body Side Assembly. The
procedure to replace the Body Side Capping is shown
in the Body Side Lower Panel procedure.
BODY SIDE REAR - UPPER
Remove
1.Disconnect both battery leads, negative lead
first.
2.Remove front, centre and rear sections of
headlining.
3.Release upper edge of front door aperture seal.
4.Release upper edge of rear door aperture seal.
5.Remove fixings from front edge of roof, and
along side being replaced.
6.Release sealant securing front edge of roof.
7.Insert wedges into top of both’B/C’posts. This
will allow access for removal of body side.
8. RH side:Remove tail door.See CHASSIS
AND BODY, Repair.
9.Remove side window.
10.Remove rear sixth light.
11.Remove all bolts securing upper body side.
Refit
12.Prepare and clean panel joint faces.
13.Reverse removal procedure.
NOTE: When refitting, ensure body side
upper is correctly fitted onto location pins.
ProCarManuals.com

PANEL REPAIRS
7
REPAIR BODY SIDE REAR - LOWER - ASSEMBLY
In this procedure the Body Side Capping and the
Corner Capping are also changed.
Remove
1.Disconnect both battery leads, negative lead
first.
2.Remove body side upper rear.See this
Section.
3.Remove all rear lamps and reflectors.
4. LH side:Remove number plate and lamp.
5. LH side:Remove tail door striker.
6. RH side:Remove fuel filler and grommet.
7.Remove all bolts and rivets securing lower body
side assembly.
Refit
8.Prepare and clean panel joint faces.
9.Reverse removal procedure.
NOTE: When refitting, ensure body side
upper is correctly fitted onto location pins.
ProCarManuals.com

77PANEL REPAIRS
8
REPAIR BODY SIDE REAR - PANEL
Remove
In this procedure the Body Side Capping and the
Corner Capping are also changed.
1.Disconnect both battery leads, negative lead
first.
2.Remove body side upper rear.See this
Section.
3.Remove rear lamp panel.See this Section.
4. LH side:Remove number plate and lamp.
5. LH side:Remove tail door striker.
6. RH side:Remove fuel filler and grommet.
Refit
7.Prepare and clean panel joint faces. Drill holes in
new body side lower panel for riveting. Spacing
of holes, dimension’A’= 100 mm (3.937’). In
conjunction with the rivets apply suitable
adhesive.
8.Prepare and clean panel joint faces.
9.Reverse removal procedure.
NOTE: When refitting, ensure body side
upper is correctly fitted onto location pins.
ProCarManuals.com

PANEL REPAIRS
9
REPAIR REAR LAMP PANEL
Remove
1.Disconnect both battery leads, negative lead
first.
2.Disconnect alternator.
3.Remove rear bench seat.
4. RH side:Remove tail door.See CHASSIS
AND BODY, Repair.
5.Remove rear lights and reflector.
6. LH side:Remove number plate and tail door
striker.
Refit
7.Prepare and clean panel joint faces.
8.Reverse removal procedure.REAR CROSSMEMBER PANEL
Remove
1.Disconnect both battery leads, negative lead
first.
2.Remove both rear lamp panels.See this
Section.
Refit
3.Prepare and clean panel joint faces.
4.Reverse removal procedure.
ProCarManuals.com

77PANEL REPAIRS
10
REPAIR ROOF ASSEMBLY
Remove
1.Disconnect both battery leads, negative lead
first.
2.Remove rear bench seats.
3.Remove front, centre and rear sections of
headlining.
4.Remove all bolts securing roof.
NOTE: Carefully cut sealant securing front
edge of roof to windscreen aperture.
Refit
5.Prepare and clean panel joint faces.
6.Reverse removal procedure.
ProCarManuals.com

82AIR CONDITIONING
4
REPAIR EVAPORATOR
Service repair no - 82.25.20
Remove
1.Remove battery cover.
2.Recover refrigerant from A/C system.See
Adjustment.
3.Remove 2 bolts securing A/C pipes to
evaporator.
4.Release pipes and discard’O’rings.
CAUTION: Immediately cap all air
conditioning pipes to prevent ingress of
dirt and moisture into the system.
5.Remove 2 screws and release fuse/relay bracket
from body and collect 2 spacers.
6.Remove 8 screws securing speakers to A/C
duct.
7.Disconnect speaker Lucars and remove
speakers.
8.Remove 4 screws and bolt securing A/C duct to
fascia panel.
ProCarManuals.com

WIPERS AND WASHERS
3
REPAIR WIPER MOTOR AND DRIVE RACK - FROM 02MY
Service repair no - 84.15.09
Remove
1.Disconnect battery negative lead.See
ELECTRICAL, Repair.
2.Remove wiper arms.See this Section.
3.Remove fascia console.See CHASSIS AND
BODY, Repair.
4.Remove air vent control knobs.
5.Remove 6 screws, remove fascia closing panel
and collect nut plate.
6.Move cover aside and loosen wiper motor drive
tube nut.
7.Remove 2 screws securing wiper motor, remove
retaining strap and mounting pad.
8.Disconnect multiplug from wiper motor.
9.Remove tube nut and remove wiper motor with
rack.
Refit
10.Lubricate wiper motor drive rack with grease.
11.Feed wiper motor rack into tube, connect
multiplug and fit but do not tighten tube nut.
12.Fit mounting pad and retaining strap, align wiper
motor and tighten screws.
13.Tighten wiper motor tube nut to8 Nm (6 lbf.ft)
and reposition nut cover.
14.Fit fascia closing panel.
ProCarManuals.com