battery LAND ROVER DEFENDER 1999 Owner's Manual

18ENGINE MANAGEMENT SYSTEM
18
DESCRIPTION AND OPERATION ELECTRONIC UNIT INJECTOR (EUI)
The EUI’s are located in the top of the engine inside the camshaft cover. There is one EUI per cylinder. They inject
finely atomised fuel directly into the combustion chamber. Each EUI has its own electrical connection, which is
linked to a common harness also located under the camshaft cover. Each of the EUI’s has its own 5 letter grading
code. This code is used so that greater EUI precision is achieved.
Using an injection timing map within its memory and information from the CKP sensor the ECM is able to
determine precise crankshaft angle. When the ECM determines the crankshaft speed and position it closes the
spill valve within the EUI. Fuel pressure rises inside the EUI to a predetermined limit of 1500 bar (22,000 lbf.in
2)on
pre EU3 models, and 1750 bar (25,500 lbf.in2) on EU3 models . At this limit the pintle lifts off its seat allowing the
fuel to inject into the combustion chamber. The ECM de-energises the spill valve to control the quantity of fuel
delivered. This causes a rapid pressure drop within the EUI which allows the EUI return spring to re-seat the
pintle, ending fuel delivery.
The electrical circuit that drives the EUI works in two stages depending on battery voltage. If battery voltage is
between 9 and 16 volts the EUI’s will provide normal engine performance. If however battery voltage falls to
between 6 and 9 volts on pre EU3 models, EUI operation is restricted to a limit of 2100 rev/min. On EU3 models,
EUI operation is restricted to idle. If the vehicle is fitted with a new ECM, the EUI grades for that specific vehicle
must be downloaded to the new ECM using TestBook. In the event of the engine failing to rev above 3000 rev/min
it is probable that the EUI grading has not been completed.
Input / Output
Input to the EUI takes the form of both mechanical and electrical signals. The mechanical input to the EUI is diesel
fuel via the fuel pump operating at approximately 4 to 5 bar (58 to 72 lbf.in
2). Each of the EUI’s is operated
mechanically by an overhead camshaft to enable injection pressures of up to 1500 bar (22,000 lbf.in2) on pre EU3
models, and 1750 bar (25,500 lbf.in2) on EU3 models, to be achieved. The ECM controls the EUI’s to ensure that
fuel delivery is precise and as intended.
The EUI’s earth paths are as follows:
EUI 1 (C0522-1) via the ECM (C0158-25) on a yellow wire.
EUI 2 (C0523-1) via the ECM (C0158-26) on a yellow/brown wire.
EUI 3 (C0524-1) via the ECM (C0158-27) on a yellow/blue wire.
EUI 4 (C0525-1) via the ECM (C0158-24) on a yellow/red wire.
EUI 5 (C0526-1) via the ECM (C0158-1) on a yellow/purple wire.
ProCarManuals.com

ENGINE MANAGEMENT SYSTEM
21
DESCRIPTION AND OPERATION RELAY - FUEL PUMP
The fuel pump relay is located in the engine compartment fuse box. It switches on the fuel pump to draw fuel from
the tank to the electronic unit injectors (EUI).
Input / Output
The fuel pump relay is a 4 pin normally open relay. The fuel pump relay (C0730-4) is provided with a feed by the
main relay (C0063-78) via header 291 on a brown/orange wire. An earth path is provided for the fuel pump relay
(C0730-6) via the ECM (C658-5) on a blue/purple wire. This energises the fuel pump relay and allows a feed to be
provided to the fuel pump. When the ECM interrupts the earth, the relay is de-energised and the fuel pump stops
operating.
The fuel pump relay can fail in one or more of the following ways:
Relay open circuit.
Short circuit to vehicle supply.
Short circuit to vehicle earth.
Broken relay return spring.
In the event of a fuel pump relay failure any of the following symptoms may be observed:
Engine will crank but not start.
If the engine is running, it will stop.
RELAY - MAIN
The main relay is located in the engine compartment fuse box and supplies battery voltage to the following:
The ECM.
The MAF sensor.
Fuel pump relay.
Input / Output
The main relay is a 4 pin normally open relay, which must be energised to provide a voltage to the ECM. The main
relay (C0063-86) is provided with an earth path via a transistor within the ECM (C0658-21) on a blue/red wire.
When the earth path is completed, the relay is energised and supplies the ECM (C0658-3, C0658-22 & C0658-27)
with a feed on brown/orange wires via header 291.
The main relay can fail in the following ways:
Relay open circuit.
Short circuit to vehicle supply.
Short circuit to vehicle earth.
Broken relay return spring.
In the event of a main relay failure any of the following symptoms may be observed:
Engine will crank but not start.
If the engine is running, it will stop.
For the ECM start up to take place the ignition feed when the switch is in position’II’must be greater than 6.0
volts.
ProCarManuals.com

18ENGINE MANAGEMENT SYSTEM
24
DESCRIPTION AND OPERATION GLOW PLUGS
The 4 glow plugs are located in the engine block on the inlet side, in cylinders 1 to 4. Cylinder 5 has no glow plug.
The glow plugs are a vital part of the engine starting strategy. The purpose of the glow plugs are:
Assist cold engine start.
Reduce exhaust emissions at low engine load/speed.
The main part of the glow plug is a tubular heating element that protrudes into the combustion chamber of the
engine.The heating element contains a spiral filament that is encased in magnesium oxide powder. At the tip of
the tubular heating element is the heater coil. Behind the heater coil and connected in series is a control coil. The
control coil regulates the heater coil to ensure that it does not overheat and cause a possible failure. The glow
plug circuit has its own control relay, located underneath the RH front seat.
Pre-heat is the length of time the glow plugs operate prior to engine cranking. The ECM controls the pre-heat time
of the glow plugs based on battery voltage and coolant temperature information via the glow plug relay.
Post-heat is the length of time the glow plugs operate after the engine starts. The ECM controls the post-heat time
based upon ECT information. If the ECT fails the ECM will operate pre-post heat time strategies with default
values from its memory. In this case, the engine will be difficult to start.
ProCarManuals.com

ENGINE MANAGEMENT SYSTEM
1
REPAIR ENGINE CONTROL MODULE (ECM)
Service repair no - 18.30.03
Remove
1.Release fixings and remove battery cover.
2.Disconnect battery negative lead.
3.Remove RH seat cushion, release clip and
remove ECM access panel.
4.Remove 3 bolts, release ECM and disconnect 2
multiplugs. Remove ECM.
Refit
5.Position new ECM and connect multiplugs.
6.Fit ECM and tighten bolts.
7.Fit access panel and RH seat cushion.
8.Reconnect battery negative lead.
9.Fit battery cover and secure with fixings.SENSOR - ENGINE COOLANT TEMPERATURE
(ECT)
Service repair no - 18.30.10
Remove
1.Disconnect battery negative lead.
2.Remove spring clip and disconnect ECT sensor
multiplug.
3.Position cloth around ECT sensor to absorb
coolant spillage.
4.Remove ECT sensor.
5.Remove sealing washer and discard.
Refit
6.Clean sealing washer, sensor threads and
sensor location.
7.Coat sensor threads with Loctite 577 and fit new
sealing washer.
8.Fit ECT sensor and tighten to20 Nm (14 lbf.ft).
9.Fit spring clip to multiplug and connect multiplug
to ECT sensor.
10.Top up cooling system.
11.Run engine to normal operating temperature.
Check for leaks around ECT sensor.
12.Reconnect battery negative lead.
ProCarManuals.com

19FUEL SYSTEM
4
DESCRIPTION AND OPERATION Fuel Pump
The fuel pump assembly comprises a top cover which locates the electrical connector, and four fuel pipe
couplings. The top cover is attached to a plastic cup shaped housing and retained on three sliding clips. Two coil
springs are located between the cover and the housing and ensure that the fuel pump remains seated positively at
the bottom of the tank when installed.
The housing locates the two stage fuel pump and also the fuel gauge sender unit. The lower part of the housing is
the swirl pot which maintains a constant level of fuel at the fuel pick-up. A coarse filter is located in the base of the
housing and prevents the ingress of contaminants into the pump and the fuel system from the fuel being drawn
into the pump. A fine filter is located in the intake to the low pressure stage to protect the pump from
contaminants. Flexible pipes connect the couplings on the top cover to the pump.
A non-return valve is located in the base of the housing. When the fuel tank is full, fuel pressure keeps the valve
lifted from its seat, allowing fuel to flow into the swirl pot. As the tank level reduces, the fuel pressure in the tank
reduces causing the valve to close. When the valve is closed, fuel is retained in the swirl pot, ensuring that the
swirl pot remains full and maintains a constant supply to the fuel pump.
The two stage pump comprises a high and low pressure stage. The low pressure stage draws fuel from the swirl
pot through a filter. The low pressure stage pumps fluid at a pressure of 0.75 bar (10.9 lbf.in) and a flow of 30
litres/hour (8 US Gallons/hour) to the fuel filter. A proportion of the fuel from the low pressure stage also passes,
via a restrictor, through a jet pump which keeps fuel circulating in the swirl pot. The high pressure stage draws the
low pressure fuel from the fuel filter and pressurises it to a pressure of 4.0 bar (58 lbf.in). The pressurised fuel is
then passed from the pump to the injectors at a flow of 180 litres/hour (47.6 US Gallons/hour). A fuel pressure
regulator is located at the rear of the engine and ensures that the delivery pressure remains at 4.0 bar (58 lbf.in)
by controlling the amount of fuel returning to the fuel tank.
The fuel pump has a maximum current draw of 15 Amps at 12 Volts and is supplied a feed (C0114-1) from the fuel
pump relay (C0730-2) on a white/purple wire.
Fuel Gauge Sender
The fuel gauge sender unit comprises a rotary potentiometer operated by a float. The float rises and falls with the
fuel level in the tank and moves the potentiometer accordingly.
A feed is supplied to the fuel gauge sender (C0114-1) by the fuel pump relay (C0730-2) on a purple/white then
white/purple wire. The sender is earthed (C0114-3) on a slate/black wire via header 287. The output voltage
(C0114-2) from the sender to the instrument pack (C1061-3) varies in relation to the fuel level. This output voltage
is connected to the fuel gauge C1054-2). The fuel gauge receives a battery voltage input (C1054-3) on a
white/green wire. This is compared with the output voltage from the potentiometer. The difference between the two
voltages determines the deflection of the fuel gauge pointer.
ProCarManuals.com

FUEL SYSTEM
1
ADJUSTMENT HEATER PLUG TEST
Service repair no - 19.90.20.01
Check
1. Test out of engine
2.Remove heater plug.See Repair.
3.UsingLRT-12-511,connect RED lead to battery
’+’positive and the BLACK lead to battery’-’
negative.
4.Position heater plug into tester and retain with
spring loaded bar.
5.Connect YELLOW lead to heater plug terminal.
6.Press red button on tester and note ammeter
reading. Keep button depressed, heater plug tip
should start to glow after 5 seconds
CAUTION: The heater plug tip must glow
first, if it fails to do so, replace heater plug.
7.The ammeter reading should show an initial
current draw of 25 amps, which should fall to 12
amps after 20 seconds.
8.Refit heater plug.See Repair.FUEL SYSTEM - BLEED
Service repair no - 19.50.07
Fuel Purging Procedure
1.If the vehicle runs out of fuel, or the fuel level is
so low that the fuel system draws air into the fuel
rail, the fuel rail will need to be purged before the
engine will start. This can be achieved by
following a set procedure. The process does not
require the use of any specialist equipment and
can be performed by the driver of the vehicle.
The process is as follows:
2.Switch off ignition and wait 15 seconds.
3.Turn ignition key to position 2 and wait 3
minutes, (this ensures that the fuel system
purges all the air from the fuel rail within the
cylinder head).
4.Depress the throttle pedal to more than 90% of
its total travel, (to the throttle stop).
5.Crank the engine keeping the throttle pedal
depressed.
NOTE: This operation is controlled by the
ECM and it is important that the purging
operation is not carried out on a vehicle
that has not run out of fuel. If it is carried out
unnecessarily it can lead to the engine flooding
and failing to start.
This operation will be cancelled:
6.As soon as engine speed exceeds 600 rev/min.
7.The driver allows the throttle pedal to close to a
position less than 90% of its travel.
8.The ignition key is released from the start
position.
NOTE: The engine must not be cranked for
more than 30 seconds in any one period.
9.Repeat the above procedure if the engine fails to
start.
ProCarManuals.com

19FUEL SYSTEM
2
ADJUSTMENT FUEL TANK - DRAIN
Service repair no - 19.55.02
1.Remove battery cover.
2.Disconnect both leads from battery, earth lead
first.
WARNING: Fuel vapour is highly
flammable and in contained spaces is also
explosive and toxic. Always have a fire
extinguisher containing FOAM, CO2, GAS OR
POWDER close at hand when handling or draining
fuel.
3.Using a fuel recovery appliance, drain the fuel
from the tank into a sealed container. Follow the
manufacturers instructions for the connection
and safe use of the appliance.
4.Remove filler cap and insert hose into filler neck.
5.Connect bowser earth line. Drain fuel.
6.Connect battery leads.
7.Fit battery cover.
ProCarManuals.com

FUEL SYSTEM
1
REPAIR ELEMENT - AIR FILTER
Service repair no - 19.10.10
Remove
1.Release 2 clips and disconnect air flow meter
from air filter cover.
2.Disconnect multiplug from AAP sensor.
3.Release 2 clips and remove cover from air filter.
4.Remove air filter element.
Refit
5.Clean air filter body and cover.
6.Fit new air filter element.
7.Position air cleaner cover and secure clips.
8.Position air flow meter and secure clips.
9.Connect AAP sensor multiplug.SENSOR - FUEL TEMPERATURE
Service repair no - 19.22.08
Remove
1.Remove 3 bolts and remove engine acoustic
cover.
2.Release fixings and remove battery cover.
3.Disconnect battery negative lead.
4.Disconnect multiplug from fuel temperature
sensor.
5.Thoroughly clean area around fuel temperature
sensor before removal.
6.Remove fuel temperature sensor and discard
sealing washer.
Refit
7.Clean fuel temperature sensor mating faces.
8.Fit new sealing washer and tighten fuel
temperature sensor to13 Nm (9 lbf. ft).
9.Connect multiplug to fuel temperature sensor.
10.Reconnect battery negative lead.
11.Fit battery cover and secure fixings.
12.Fit engine acoustic cover and secure with bolts.
ProCarManuals.com

19FUEL SYSTEM
4
REPAIR ELEMENT - FUEL FILTER
Service repair no - 19.25.07
Remove
1.Release fixings and remove battery cover.
2.Disconnect battery negative lead.
3.Raise rear of vehicle.
WARNING: Support on safety stands.
4.Release fixing and remove fuel filter cover.
5.Clean area around fuel filter.
6.Disconnect multiplug from filter element.
7.Remove fuel filter element.
Refit
8.Clean fuel filter and mating face.
9.Fit new fuel filter element and connect multiplug.
10.Position fuel filter cover and secure with fixing.
11.Remove stand(s) and lower vehicle.
12.Reconnect battery negative lead.
13.Fit and secure battery cover.COOLER - FUEL
Service repair no - 19.25.30
Remove
1.Remove 3 bolts and remove engine acoustic
cover.
2.Remove battery cover.
3.Disconnect battery negative lead.
4.Drain cooling system.See COOLING
SYSTEM, Adjustment.
5.Release 3 clips and disconnect 3 coolant hoses
from fuel cooler.
6.Release 2 fuel hoses from fuel cooler.
CAUTION: Plug the connections.
7.Release vacuum pipe clip from fuel cooler.
8.Remove 4 bolts securing fuel cooler to inlet
manifold and remove cooler.
Refit
9.Clean fuel hose connections.
10.Position fuel cooler to inlet manifold. Apply
Loctite 242 to bolts and tighten to18 Nm (13
lbf.ft).
11.Connect fuel hoses.
12.Connect coolant hoses, secure with clips.
13.Secure vacuum hose to fuel cooler.
14.Refill cooling system.See COOLING SYSTEM,
Adjustment.
15.Fit engine acoustic cover and secure with bolts.
16.Reconnect battery negative lead.
17.Fit battery cover.
ProCarManuals.com

FUEL SYSTEM
5
REPAIR TURBOCHARGER
Service repair no - 19.42.01
Remove
1.Remove battery cover.
2.Disconnect battery negative lead.
3.Remove 3 bolts and remove engine acoustic
cover.
4.Release clip and disconnect breather hose from
camshaft cover.
5.Release clips and disconnect air flow meter from
air filter.
6.Disconnect multiplug from air flow meter.
7.Loosen clip screw and remove air inlet hose
from turbocharger.
8.Remove 3 bolts and remove exhaust manifold
heat shield.
9.Release clip and disconnect vacuum hose from
turbocharger wastegate.
10.Loosen clip screw and release air outlet hose
from turbocharger.
11.Remove turbocharger oil feed banjo bolt and
discard sealing washers.
12.Remove 3 nuts and release exhaust front pipe
from turbocharger and discard gasket.
13.Remove 3 nuts securing turbocharger to exhaust
manifold.
14.Loosen and unscrew turbocharger drain pipe
union from cylinder block.
15.Remove turbocharger and discard gasket.
16.Remove 2 bolts and remove turbocharger oil
drain pipe. Discard gasket.
ProCarManuals.com